Eneas U de Queiroz [Mon, 24 Feb 2020 12:59:38 +0000 (09:59 -0300)]
kernel: build neon-asm version of ghash module
This alone improves AES-GCM performance by up to 50% on ipq40xx. This
is enabled for targets that support neon and set CONFIG_ARM_CRYPTO:
imx6, ipq40xx, and mvebu.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Eneas U de Queiroz [Fri, 20 Dec 2019 13:52:17 +0000 (10:52 -0300)]
ipq40xx: qce - add fixes for AES ciphers
This backports commits from master that fix AES ciphers when using the
qce driver:
- A couple of simple fixes for CTR and XTS modes used with AES:
* 041-crypto-qce-fix-ctr-aes-qce-block-chunk-sizes.patch
* 042-crypto-qce-fix-xts-aes-qce-key-sizes.patch
- A fix for a bug that affected cases when there were more entries in
the input sg list than necessary to actually encrypt, resulting in
failure in gcm, where the authentication tag is present after the
encryption data:
* 043-crypto-qce-save-a-sg-table-slot-for-result-buf.patch
- A fix to update the IV buffer passed to the driver from the kernel:
* 044-crypto-qce-update-the-skcipher-IV.patch
- A patch that reduces memory footprint and driver initialization by
only initializing the fallback mechanism where it is actually used:
* 046-crypto-qce-initialize-fallback-only-for-AES.patch
- Three patches that make gcm and xts modes work with the qce driver,
and improve performance with small blocks:
* 047-crypto-qce-use-cryptlen-when-adding-extra-sgl.patch
* 048-crypto-qce-use-AES-fallback-for-small-requests.patch
* 049-crypto-qce-handle-AES-XTS-cases-that-qce-fails.patch
- A patch that allows the hashes/ciphers to be built individually.
* 051-crypto-qce-allow-building-only-hashes-ciphers.patch
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[renumbered patches, added patches from dropped commit, refreshed, 5.4]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Eneas U de Queiroz [Fri, 21 Feb 2020 18:44:39 +0000 (15:44 -0300)]
ipq40xx: use neon crypto drivers
This adds the neon based implementations of AES & SHA256.
For AES, according to the kernel config help:
Use a faster and more secure NEON based implementation of AES in CBC,
CTR and XTS modes.
Bit sliced AES gives around 45% speedup on Cortex-A15 for CTR mode
and for XTS mode encryption, CBC and XTS mode decryption speedup is
around 25%. (CBC encryption speed is not affected by this driver.)
This implementation does not rely on any lookup tables so it is
believed to be invulnerable to cache timing attacks.
...
The observed speedups on ipq40xx are more modest: speedup is around 20%
for CTR mode and for XTS mode encryption, CBC and XTS mode decryption
speedup is around 10%. Measurements were made using tcrypt, with
1024-bytes blocks for CTR & CBC, and 4096-bytes for XTS.
The aes-neon-bs driver uses a fallback for CBC encryption; that fallback
could be either the generic driver written in C, or the scalar arm-asm
one. Even though aes-arm is 1.9% slower, it is more resilient to timing
attacks (the reason for being slower), so it is being included here.
The neon sha256 module increases performance over the generic module by
33%.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[Enable only ciphers for now, reorder patch in series to help bisect
as new symbols could lead to build failures, 5.4]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Eneas U de Queiroz [Fri, 20 Dec 2019 13:37:21 +0000 (10:37 -0300)]
ipq40xx: qce - switch to skcipher API
This backports a commit updating the API of the QCE crypto engine to
what is used in current kerenl, easing future upstream backports.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[renumber patches, refreshed, added 5.4 patches]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Wed, 26 Feb 2020 21:25:34 +0000 (22:25 +0100)]
kernel: 4.19,5.4: disable ARM CE & NEON
This patch disables the CRYPTO KERNEL SYMBOLs that are touched
by the upcoming ipq40xx patch "ipq40xx: use neon crypto drivers"
from "Eneas U de Queiroz" and more so for his follow up patches
for the other ARM targets in this series. This should help to
prevent at least a few potential build errors on other archs.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Steven Lin [Mon, 2 Sep 2019 02:39:45 +0000 (10:39 +0800)]
ipq40xx: add support for EnGenius EAP2200
SOC: IPQ4019 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
FLASH: NOR 4 MiB + NAND 128 MiB
ETH: Qualcomm Atheros QCA8072
WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11a/n/ac 2:2x2
WLAN2: Qualcomm Atheros QCA9888 5GHz 802.11a/n/ac 2:2x2
INPUT: WPS Button
LEDS: Power, LAN1, LAN2, WLAN 2.4GHz, WLAN 5GHz-1, WLAN 5GHz-2, OPMODE
1. Load Ramdisk via U-Boot
To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
* 115200bps
* 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports.
c. Set a static ip 192.168.99.8 for Ethernet that connects to board.
d. The PC must have a TFTP server launched and listening on the interface to which the board is connected.
e. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.
U-BOOT> set serverip 192.168.99.9 && tftpboot 0x84000000 192.168.99.8:openwrt.itb && bootm
Signed-off-by: Steven Lin <steven.lin@senao.com>
[copied 4.19 dts to 5.4]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Adrian Schmutzler [Fri, 28 Feb 2020 19:00:10 +0000 (20:00 +0100)]
ipq807x: fix indent in image/Makefile
Convert space indent to tab like the rest of the file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Álvaro Fernández Rojas [Fri, 28 Feb 2020 18:30:16 +0000 (19:30 +0100)]
bcm27xx-userland: update to latest version
Remove upstream cmake fix.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Kevin Darbyshire-Bryant [Wed, 5 Feb 2020 19:48:27 +0000 (19:48 +0000)]
kernel: 5.4 fix build on darwin
Fix typedef clash on darwin.
HOSTCC scripts/mod/file2alias.o
scripts/mod/file2alias.c:47:3: error: typedef redefinition with different types ('struct uuid_t' vs '__darwin_uuid_t' (aka 'unsigned char [16]'))
} uuid_t;
^
/Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer/SDKs/MacOSX.sdk/usr/include/sys/_types/_uuid_t.h:31:25: note: previous definition is here
typedef __darwin_uuid_t uuid_t;
^
scripts/mod/file2alias.c:1305:42: error: array initializer must be an initializer list or string literal
DEF_FIELD(symval, tee_client_device_id, uuid);
^
2 errors generated.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
John Crispin [Wed, 26 Feb 2020 12:01:32 +0000 (13:01 +0100)]
ipq807x: add very basic target support
This is still missing a lot of love but people want to start working on it
so lets give them a common baseline.
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Tue, 14 Jan 2020 16:15:57 +0000 (17:15 +0100)]
ipq40xx: add v5.4 support
Signed-off-by: John Crispin <john@phrozen.org>
Mark-MC Lee (李明昌) [Mon, 10 Feb 2020 08:33:15 +0000 (09:33 +0100)]
mediatek: add v5.4 support
Signed-off-by: Mark-MC Lee (李明昌) <Mark-MC.Lee@mediatek.com>
John Crispin [Mon, 10 Feb 2020 06:46:56 +0000 (07:46 +0100)]
bcm53xx: add v5.4 support
Signed-off-by: John Crispin <john@phrozen.org>
Koen Vandeputte [Mon, 9 Dec 2019 14:19:26 +0000 (15:19 +0100)]
imx6: add support for kernel 5.4
Refreshed all patches.
Refreshed kernel config.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
David Bauer [Wed, 4 Dec 2019 16:35:04 +0000 (17:35 +0100)]
mpc85xx: add support for kernel 5.4
Signed-off-by: David Bauer <mail@david-bauer.net>
Hauke Mehrtens [Mon, 17 Feb 2020 23:36:28 +0000 (00:36 +0100)]
ath79: Make upstream ag71xx driver work
* Fix some bugs in the driver
* Add missing clock and reset references in dts
* Rename mdio-bus to mdio so the driver find it
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
David Bauer [Sun, 8 Dec 2019 20:44:23 +0000 (21:44 +0100)]
ath79: add support for kernel 5.4
Signed-off-by: David Bauer <mail@david-bauer.net>
[refreshed]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* Sync the patches with the changes done for kernel 4.19
* Use KERNEL_TESTING_PATCHVER
* Refresh the configuration
* Fix multiple compile bugs in the patches
* Only add own ag71xx files for kernel 4.19 and use upstream version for
5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Christian Lamparter [Sat, 30 Nov 2019 19:57:11 +0000 (20:57 +0100)]
apm821xx: add linux kernel 5.4 testing support
This patch adds support for the linux kernel version 5.4
as an optional testing kernel.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hauke Mehrtens [Sun, 23 Feb 2020 17:57:45 +0000 (18:57 +0100)]
kernel: Use new symbol to deactivate MIPS FPU support
With kernel 5.4 the upstream kernel supports deactivating the FPU
support on MIPS. Use this new upstream feature instead of our older
patch which was removed when porting the kernel patches to kernel 5.4.
This way both options are set which should work for older kernel
versions and also new ones.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 23 Feb 2020 15:46:01 +0000 (16:46 +0100)]
kernel: Remove nvmem hack patch from 5.4
The nvmem framework is now used in net/ethernet/eth.c and the nvmem
sysfs is split into a separate Kconfig option. More work would be needed
to adapt this patch for the broader use. The current patch compiles fine
on ath79, but it breaks the x86 target.
nvmem is also compiled into the kernel for most of our targets for
example ath79 anyway, so patching the kernel to remove it is now harder
and not the case on multiple targets anyway. Instead of making this work
on kernel 5.4 just remove this hack patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 23 Feb 2020 15:41:58 +0000 (16:41 +0100)]
kernel: Remove chash.ko from kmod-drm-amdgpu
This module was added with kernel 4.15, but is was removed again with
kernel version 5.3. OpenWrt does not support specifying a kernel version
range so just break it with kernel 4.14 and only support recent kernel
versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 23 Feb 2020 15:41:16 +0000 (16:41 +0100)]
kernel: Add snd-intel-nhlt.ko to kmod-sound-hda-intel
With kernel 5.4 kmod-sound-hda-intel also needs snd-intel-nhlt.ko, but
this kernel module is only build on x86, make the OpenWrt kmod depend on
TARGET_x86.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 23 Feb 2020 15:39:30 +0000 (16:39 +0100)]
kernel: Make kmod-ixgbe depend on kmod-libphy
With kernel 5.4 kmod-ixgbe is depending on kmod-libphy, add this
missing dependency.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 23 Feb 2020 15:28:21 +0000 (16:28 +0100)]
kernel: Make LIB_ARC4 selectable
This makes it possible to select CONFIG_CRYPTO_LIB_ARC4 directly. We
need this to be able to compile this into the kernel and make use of it
from mac80211 backports.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Wed, 5 Feb 2020 21:57:14 +0000 (22:57 +0100)]
nat46: Fix compile with kernel 5.4
nf_reset() was renamed to nf_reset_ct() in upstream Linux commit
895b5c9f206e ("netfilter: drop bridge nf reset from nf_reset)"
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Koen Vandeputte [Fri, 28 Feb 2020 14:09:27 +0000 (15:09 +0100)]
kernel: Make kmod-rtc-pcf2123 depend on kmod-regmap-spi
In kernel 5.4 kmod-rtc-pcf2123 depends on kmod-regmap-spi, add this missing
dependency.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Hauke Mehrtens [Wed, 5 Feb 2020 21:58:57 +0000 (22:58 +0100)]
kernel: Make kmod-nft-core depend on kmod-nf-nat
In kernel 5.4 kmod-nf-core depends on kmod-nf-nat, add this missing
dependency.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Fri, 31 Jan 2020 12:48:24 +0000 (13:48 +0100)]
kernel: Make kmod-fs-f2fs depend on kmod-nls-base
Since kernel 5.4 kmod-fs-f2fs is depending on kmod-nls-base.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Fri, 31 Jan 2020 12:47:29 +0000 (13:47 +0100)]
kernel: Add of_touchscreen.ko to kmod-input-touchscreen-ads7846
kmod-input-touchscreen-ads7846 depends on of_touchscreen.ko since
kernel 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Fri, 31 Jan 2020 12:46:31 +0000 (13:46 +0100)]
kernel: Remove kmod-gigaset for kernel 5.4
gigaset was moved to staging in kernel 5.4, just deactivate it on
recent kernel versions instead of adapting it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Fri, 31 Jan 2020 12:45:07 +0000 (13:45 +0100)]
kernel: Add roles.ko to kmod-usb-chipidea
kmod-usb-chipidea depends on roles.ko since kernel 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Fri, 31 Jan 2020 12:40:10 +0000 (13:40 +0100)]
kernel: Make kmod-gpio-pca953x depend on kmod-regmap-i2c
In kernel 5.4 kmod-gpio-pca953x depends on kmod-regmap-i2c.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Fri, 31 Jan 2020 12:38:23 +0000 (13:38 +0100)]
kernel: module v4l2-common.ko was removed
The content of v4l2-common.ko was merged into videodev.ko and it was
removed in kernel 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Fri, 31 Jan 2020 12:36:15 +0000 (13:36 +0100)]
kernel: Adapt moved crodic.ko module
The module was moved in the kernel, adapt OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Fri, 31 Jan 2020 12:32:03 +0000 (13:32 +0100)]
kernel: Add crypto libraries to modules
In kernel 5.3 and 5.4 some crypto modules were split into two modules,
one implementing the crypto algorithm and the other integrating it
into the Linux crypto framework.
Adapt OpenWrt to support this split.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Koen Vandeputte [Sun, 23 Feb 2020 14:30:37 +0000 (15:30 +0100)]
kernel: Include xt_MASQUERADE for kernel 5.2 and later
Instead of ip6t_MASQUERADE, include xt_MASQUERADE on kernel >= 5.2.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Sun, 23 Feb 2020 14:28:15 +0000 (15:28 +0100)]
kernel: mode_beet mode_transport mode_tunnel xfram modules
This adds the new xfrm4_mode_beet, xfrm4_mode_transport,
xfrm4_mode_tunnel and their IPv6 versions on kernel 5.4. These modules
were newly added in kernel 5.2.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Hauke Mehrtens [Sun, 23 Feb 2020 15:46:41 +0000 (16:46 +0100)]
x86: Update configuration
The configuration was refreshed and KERNEL_TESTING_PATCHVER was set to
make it easy to compile for kernel 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 23 Feb 2020 13:58:32 +0000 (14:58 +0100)]
x86: Refresh patches on kernel 5.4
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 23 Feb 2020 13:55:25 +0000 (14:55 +0100)]
x86: copy kernel patches from 4.19 to 5.4
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Koen Vandeputte [Mon, 25 Nov 2019 15:08:31 +0000 (16:08 +0100)]
kernel: add support for kernel 5.4
The following patches were removed because they are integrated in the upstream kernel 5.4:
* backport-5.4/047-v4.21-mtd-keep-original-flags-for-every-struct-mtd_info.patch
* backport-5.4/048-v4.21-mtd-improve-calculating-partition-boundaries-when-ch.patch
* backport-5.4/080-v5.1-0001-bcma-keep-a-direct-pointer-to-the-struct-device.patch
* backport-5.4/080-v5.1-0002-bcma-use-dev_-printing-functions.patch
* backport-5.4/095-Allow-class-e-address-assignment-via-ifconfig-ioctl.patch
* backport-5.4/101-arm-cns3xxx-use-actual-size-reads-for-PCIe.patch
* backport-5.4/200-v5.2-usb-dwc2-Set-lpm-mode-parameters-depend-on-HW-configuration.patch
* backport-5.4/210-arm64-sve-Disentangle-uapi-asm-ptrace.h-from-uapi-as.patch
* backport-5.4/380-v5.3-net-sched-Introduce-act_ctinfo-action.patch
* backport-5.4/450-v5.0-mtd-spinand-winbond-Add-support-for-W25N01GV.patch
* backport-5.4/451-v5.0-mtd-spinand-Add-initial-support-for-Toshiba-TC58CVG2.patch
* backport-5.4/452-v5.0-mtd-spinand-add-support-for-GigaDevice-GD5FxGQ4xA.patch
* backport-5.4/455-v5.1-mtd-spinand-Add-support-for-all-Toshiba-Memory-produ.patch
* backport-5.4/456-v5.1-mtd-spinand-Add-support-for-GigaDevice-GD5F1GQ4UExxG.patch
* backport-5.4/460-v5.0-mtd-spi-nor-Add-support-for-mx25u12835f.patch
* backport-5.4/460-v5.3-mtd-spinand-Define-macros-for-page-read-ops-with-thr.patch
* backport-5.4/461-v5.3-mtd-spinand-Add-support-for-two-byte-device-IDs.patch
* backport-5.4/462-v5.3-mtd-spinand-Add-support-for-GigaDevice-GD5F1GQ4UFxxG.patch
* backport-5.4/463-v5.3-mtd-spinand-Add-initial-support-for-Paragon-PN26G0xA.patch
* backport-5.4/700-v5.1-net-phylink-only-call-mac_config-during-resolve-when.patch
* backport-5.4/701-v5.2-net-phylink-ensure-inband-AN-works-correctly.patch
* backport-5.4/702-v4.20-net-ethernet-Add-helper-for-MACs-which-support-asym-.patch
* backport-5.4/703-v4.20-net-ethernet-Add-helper-for-set_pauseparam-for-Asym-.patch
* backport-5.4/704-v4.20-net-phy-Stop-with-excessive-soft-reset.patch
* backport-5.4/705-v5.1-net-phy-provide-full-set-of-accessor-functions-to-MM.patch
* backport-5.4/706-v5.1-net-phy-add-register-modifying-helpers-returning-1-o.patch
* backport-5.4/707-v5.1-net-phy-add-genphy_c45_check_and_restart_aneg.patch
* backport-5.4/708-v5.3-net-phylink-remove-netdev-from-phylink-mii-ioctl-emu.patch
* backport-5.4/709-v5.3-net-phylink-support-for-link-gpio-interrupt.patch
* backport-5.4/710-v5.3-net-phy-allow-Clause-45-access-via-mii-ioctl.patch
* backport-5.4/711-v5.3-net-sfp-add-mandatory-attach-detach-methods-for-sfp-.patch
* backport-5.4/712-v5.3-net-sfp-remove-sfp-bus-use-of-netdevs.patch
* backport-5.4/713-v5.2-net-phylink-avoid-reducing-support-mask.patch
* backport-5.4/714-v5.3-net-sfp-Stop-SFP-polling-and-interrupt-handling-duri.patch
* backport-5.4/715-v5.3-net-phylink-don-t-start-and-stop-SGMII-PHYs-in-SFP-m.patch
* backport-5.4/740-v5.5-net-phy-avoid-matching-all-ones-clause-45-PHY-IDs.patch
* backport-5.4/741-v5.5-net-phylink-fix-link-mode-modification-in-PHY-mode.patch
* pending-5.4/103-MIPS-perf-ath79-Fix-perfcount-IRQ-assignment.patch
* pending-5.4/131-spi-use-gpio_set_value_cansleep-for-setting-chipsele.patch
* pending-5.4/132-spi-spi-gpio-fix-crash-when-num-chipselects-is-0.patch
* pending-5.4/220-optimize_inlining.patch
* pending-5.4/341-MIPS-mm-remove-no-op-dma_map_ops-where-possible.patch
* pending-5.4/475-mtd-spi-nor-Add-Winbond-w25q128jv-support.patch
* pending-5.4/477-mtd-add-spi-nor-add-mx25u3235f.patch
* pending-5.4/479-mtd-spi-nor-add-eon-en25qh64.patch
Some bigger changes were done to this feature and we did not port this patch yet:
* hack-5.4/207-disable-modorder.patch
This depends on BOOTMEM which was removed from the kernel, this needs some bigger changes:
* hack-5.4/930-crashlog.patch
A different version of the FPU disable patch was merged upstream, OpenWrt needs some adaptations.
* pending-5.4/304-mips_disable_fpu.patch
- no crashlog support yet as a required file got deleted upstream
- Removed patch below, which is now seen as a recursive dependency [1]
- Removed patch below due to build error [2]
- fix still required to avoid identical function def [3]
- Fixes included from Blocktrron
- Fixes included from Chunkeey
- Fix included from nbd regarding "dst leak in Flow Offload"
[1] target/linux/generic/hack-5.4/260-crypto_test_dependencies.patch
[2] target/linux/generic/hack-5.4/207-disable-modorder.patch
[3] target/linux/generic/pending-5.4/613-netfilter_optional_tcp_window_check.patch
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 23 Feb 2020 12:20:11 +0000 (13:20 +0100)]
kernel: copy kernel 4.19 code to 5.4
No changes were done to the patches while coping them. Currently they do
not apply on top of kernel 5.4.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Jo-Philipp Wich [Thu, 27 Feb 2020 21:03:18 +0000 (22:03 +0100)]
libubox: update to latest Git HEAD
7da6643 tests: blobmsg: add test case
75e300a blobmsg: fix wrong payload len passed from blobmsg_check_array
Fixes: FS#2833
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Adrian Schmutzler [Thu, 27 Feb 2020 13:49:08 +0000 (14:49 +0100)]
ath79: also reduce spi-max-frequency for buffalo_wzr-hp-ag300h
In accordance to
ebc090e420d1 ("ath79: reduce spi-max-frequency to 50 MHz")
this also reduces the spi-max-frequency to 50 MHz for the last remaining
device with higher frequency in ath79. This will save us from having a
single special case that will require adjustment when the spi driver for
this device is changed in the future.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Chuanhong Guo <gch981213@gmail.com>
Adrian Schmutzler [Thu, 27 Feb 2020 12:05:51 +0000 (13:05 +0100)]
kirkwood: apply minor DTS style improvements
This applies some minor DTS style improvements to the files kept
in OpenWrt at the moment:
- harmonize/improve LED/pinmux node names
- harmonize empty lines between nodes
- change "ok" to "okay"
- some other minor formatting adjustments
Since changes are only cosmetical, they are only applied to the
"newer" DTS files for kernel 4.19.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Mon, 24 Feb 2020 12:06:04 +0000 (21:06 +0900)]
kirkwood: convert DTS patches into plain DTS files
Move DTS files newly created by patch files to files directory. This will make
these files much more maintainable.
Patching the kernel Makefile is unnecessary, as the DTS files specified in
DEVICE_DTS will be compiled by OpenWrt buildroot anyway.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Thu, 27 Feb 2020 10:55:36 +0000 (11:55 +0100)]
ath79: reduce spi-max-frequency to 50 MHz
The introduction of
ebf0d8dadeca ("ath79: add new ar934x spi driver")
made the SPI memory unusable on devices with very high spi-max-frequency
(104 MHz).
Here's how the actual clock is calculated: (AHB_CLK/((CLOCK_DIVIDER+1)*2))
where AHB_CLK is a fixed clock (e.g. 200MHz on AR9331) and CLOCK_DIVIDER
is the parameter we can set. Highest clock according to this formula is
AHB_CLK/2 (100MHz, but that didn't work in device tests).
The next possible value is AHB_CLK/4 (50MHz). Speeds between 50 MHz and
100 MHz will be rounded down, so using values higher than 50 MHz does
not provide any benefit.
Consequently, this patch reduces spi-max-frequency for all devices with
values higher than 50 MHz to 50 MHz (effectively, this only affects
devices with 104 MHz before this patch).
Tested on GL.inet GL-AR150:
Boot fails with 104 MHz but is successful with both 50 MHz and 80 MHz
(fast-read), where the latter two yield identical read speeds.
Fixes:
ebf0d8dadeca ("ath79: add new ar934x spi driver")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Roger Pueyo Centelles [Mon, 24 Feb 2020 20:07:59 +0000 (21:07 +0100)]
ath79: fix spi-max-frequency for wAP G-5HacT2HnD
The introduction of
ebf0d8dade (ath79: add new ar934x spi driver)
made the SPI memory unusable. Reducing the spi-max-frequency to
a smaller value makes it work again.
Tested on two MikroTik RouterBOARD wAP G-5HacT2HnD devices.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Xu Wang [Sat, 8 Feb 2020 23:04:11 +0000 (23:04 +0000)]
base-files: add all buildinfo with INCLUDE_CONFIG
CONFIG_INCLUDE_CONFIG option is helpful for being able to rebuild the
exact same firmware as you see on a live OpenWRT instance, but it's
crucially missing feeds information, so we can't rebuild the exact same
package versions. This commit fixes this by adding the remaining feeds
(and version) buildinfo files to the image.
Signed-off-by: Xu Wang <xwang1498@gmx.com>
Petr Štetiar [Thu, 20 Feb 2020 08:03:54 +0000 (09:03 +0100)]
ppp: backport security fixes
8d45443bb5c9 pppd: Ignore received EAP messages when not doing EAP
8d7970b8f3db pppd: Fix bounds check in EAP code
858976b1fc31 radius: Prevent buffer overflow in rc_mksid()
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes: CVE-2020-8597
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Jo-Philipp Wich [Wed, 26 Feb 2020 15:36:16 +0000 (16:36 +0100)]
Revert "ppp: backport security fixes"
This reverts commit
215598fd03899c19a9cd26266221269dd5ec8cee since it
didn't contain a reference to the CVE it addresses. The next commit
will re-add the commit including a CVE reference in its commit message.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Roger Pueyo Centelles [Sun, 26 Jan 2020 16:56:05 +0000 (17:56 +0100)]
ath79: add support for MikroTik RouterBOARD 922UAGS-5HPacD
This patch ports support for the MikroTik RouterBOARD 922UAGS-5HPacD
with a built-in 802.11ac High-Power radio (31dBm), which was already
available in the ar71xx target.
See https://mikrotik.com/product/RB922UAGS-5HPacD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9558 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9882 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE-in 24V
- SFP: 1x host
- USB: 1x 2.0 type A
- PCIe: 1x Mini slot (also contains USB 2.0 for 3G/LTE modems)
- SIM slot: 1x mini-SIM
Working:
- Board/system detection
- SPI and NAND storage
- PCIe
- USB type A host
- Wireless
- Ethernet
- LEDs (user, phy0)
- Reset button
- Sysupgrade to/from ar71xx
Not supported:
- RSSI LEDs
- SFP cage
Installation methods:
- Sysupgrade from ar71xx (it is advisable to use the -n option to
wipe any previous settings), or
- Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Roger Pueyo Centelles [Wed, 29 Jan 2020 10:27:03 +0000 (11:27 +0100)]
rbextract: support devices with plain RLE caldata
Old MikroTik devices have the RLE-encoded radio calibration data
directly stored in the art (hard_config) partition, without LZO
compression nor any preceding ERD magic bytes. This commit adds
a fallback for these devices.
Tested on the ath79 target with a MikroTik SXT 5nD r2 (SXT Lite5),
only locally --not yet merged upstream--.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Kevin Darbyshire-Bryant [Tue, 25 Feb 2020 16:38:35 +0000 (16:38 +0000)]
kernel: x86_64: drop CALGARY properly
Use correct config syntax of 'is not set' instead of just commenting the
line
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
John Crispin [Tue, 25 Feb 2020 16:15:07 +0000 (17:15 +0100)]
mediatek: add latest fixes provided by MTK
Signed-off-by: John Crispin <john@phrozen.org>
Kevin Darbyshire-Bryant [Mon, 24 Feb 2020 13:53:57 +0000 (13:53 +0000)]
kernel: x86_64: drop CALGARY IOMMU
The calgary IOMMU was only used on high-end IBM systems in the early
x86_64 age. This is an unlikely OpenWrt target and in fact upstream
are looking to drop the driver entirely with the bonus that we no
longer see:
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
John Crispin [Tue, 25 Feb 2020 16:03:44 +0000 (17:03 +0100)]
mac80211: enhance wifi reload
If the reconf call fails force a full restart of the radio.
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Tue, 25 Feb 2020 16:01:55 +0000 (17:01 +0100)]
hostapd: enhance wifi reload
Add a radio_config_id property. If the radio config changes return an error
upon receiving the reconf call.
Signed-off-by: John Crispin <john@phrozen.org>
Felix Fietkau [Tue, 25 Feb 2020 12:33:46 +0000 (13:33 +0100)]
mt76: update to the latest version
0a53dcda5203 mt76: mt7603: add upper limit for dynamic sensitivity minimum receive power
46e63c05f7d1 mt76: mt7603: enable dynamic sensitivity adjustment by default
81476f11b68c mt76: mt7615: fix antenna mask initialization in DBDC mode
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Piotr Dymacz [Fri, 31 Jan 2020 14:22:54 +0000 (15:22 +0100)]
base-files: diag: restore default trigger for 'boot' LED
For devices without a dedicated 'diag' LED, we use sometimes one of
other LEDs for indicating at least 'boot', 'failsafe' and 'upgrade'
stages. In some cases, at the same time these LEDs have defined default
triggers in DTS using 'linux,default-trigger' property. Current 'diag'
setup removes the trigger and turns off 'boot' LED after bootup.
One of the examples of such device is TP-Link TL-WR841N v14 (ramips)
which uses 'wlan' LED with defined 'linux,default-trigger' for 'diag':
aliases {
led-boot = &led_wlan;
led-failsafe = &led_wlan;
led-upgrade = &led_wlan;
};
[...]
led_wlan: wlan {
label = "tl-wr841n-v14:green:wlan";
gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
This patch extends 'diag.sh' and 'leds.sh' scripts to make sure default
trigger defined in DTS is restored for 'diag' LED which isn't used for
indicating 'running' stage.
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Piotr Dymacz [Mon, 20 Jan 2020 18:35:01 +0000 (19:35 +0100)]
hostapd: start hostapd/wpa_supplicant for all wiphy devices
c888e17e06 ("hostapd: manage instances via procd instead of pidfile")
added procd support for managing hostapd and wpa_supplicant daemons
but at the same time limited wiphy names to 'phy*'.
This brings back initial behaviour (introduced in
60fb4c92b6 ("hostapd:
add ubus reload") and makes procd manage daemons for any wiphy device
found in '/sys/class/ieee80211'.
CC: Felix Fietkau <nbd@nbd.name>
CC: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Piotr Dymacz [Mon, 25 Nov 2019 20:00:30 +0000 (21:00 +0100)]
umbim: move package to 'WWAN' submenu
'uqmi' was moved to 'WWAN' submenu in
9abdeee0b7.
Let's be consistent and do the same with 'umbim'.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Josef Schlehofer [Sat, 22 Feb 2020 22:03:37 +0000 (23:03 +0100)]
mbedtls: use correct SPDX License Identifier and add License file
License "GPL-2.0+" is deprecated License Identifier according to
SPDX License list [1]. The correct one is GPL-2.0-or-later.
While at it, also add the License file.
[1] https://spdx.org/licenses/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Josef Schlehofer [Sat, 22 Feb 2020 22:03:36 +0000 (23:03 +0100)]
mbedtls: update to version 2.16.5
Changelog:
https://tls.mbed.org/tech-updates/releases/mbedtls-2.16.5-and-2.7.14-released
Security advisory:
https://tls.mbed.org/tech-updates/security-advisories/mbedtls-security-advisory-2020-02
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Josef Schlehofer [Sun, 23 Feb 2020 07:48:39 +0000 (08:48 +0100)]
strace: update to version 5.5
Changelog:
https://strace.io/files/5.5/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Hauke Mehrtens [Sun, 23 Feb 2020 12:20:11 +0000 (13:20 +0100)]
kernel: Sort generic configuration
This was done by executing these commands:
$ ./scripts/kconfig.pl '+' target/linux/generic/config-4.19 /dev/null > target/linux/generic/config-4.19-new
$ mv target/linux/generic/config-4.14-new target/linux/generic/config-4.14
$ ./scripts/kconfig.pl '+' target/linux/generic/config-4.14 /dev/null > target/linux/generic/config-4.14-new
$ mv target/linux/generic/config-4.19-new target/linux/generic/config-4.19
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 22 Feb 2020 19:39:47 +0000 (20:39 +0100)]
linux-atm: Fix compile warning
The function trace_on_exit() is given to atexit() as a parameter, but
atexit() only takes a function pointer to a function with a void
parameter.
This problem was introduced when the on_exit() function was incompletely
replaced by atexit().
Fixes:
ba6c8bd6142f ("linux-atm: add portability fixes")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 9 Nov 2019 16:06:06 +0000 (17:06 +0100)]
ath10k-ct: Use ath10k-ct version 5.4
This makes ath10k-ct use the version based on kernel 5.4 by default.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 22 Feb 2020 18:12:34 +0000 (19:12 +0100)]
ath10k-ct: Update to version 2020-02-18
This adds AP VLAN support.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 9 Nov 2019 16:06:05 +0000 (17:06 +0100)]
mac80211: Allow IBSS mode and different beacon intervals
ath10k-ct supports the combination to select IBSS (ADHOC) mode and
different beacon intervals together. mac80211 does not like this
combination, but Ben says this is ok, so remove this check.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Wed, 5 Feb 2020 21:49:27 +0000 (22:49 +0100)]
rtl8812au-ct: Update to version 2020-01-12
This fixes compile problems with kernel 5.4
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Roger Pueyo Centelles [Mon, 24 Feb 2020 17:21:49 +0000 (18:21 +0100)]
ath79: add missing reset-gpios for NanoStation Loco M (XW)
When porting support from ar71xx to ath79, the reset-gpios option was
missed. Due to a hardware bug, this would eventually leave the devices
with RX-deaf Ethernet PHY.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Koen Vandeputte [Mon, 24 Feb 2020 15:11:02 +0000 (16:11 +0100)]
kernel: bump 4.19 to 4.19.106
Refreshed all patches.
Remove upstreamed:
- 950-0786-leds-pca963x-Fix-open-drain-initialization.patch
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Sungbo Eo [Sun, 23 Feb 2020 15:14:22 +0000 (00:14 +0900)]
kirkwood: remove kmod-i2c-mv64xxx from DEVICE_PACKAGES
Commit
9a1f441ac81c ("kirkwood: enable SoC drivers in the kernel config")
enabled I2C_MV64XXX in the kernel config, and the subsequent commit
0d5ba94088ef
("orion: enable SoC drivers in the kernel config") removed kmod-i2c-mv64xxx
package entirely. As the feature is now kernel built-in and the package does not
exist anymore, we can safely remove kmod-i2c-mv64xxx from DEVICE_PACKAGES.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Koen Vandeputte [Fri, 21 Feb 2020 14:09:00 +0000 (15:09 +0100)]
kernel: bump 4.19 to 4.19.105
Refreshed all patches.
Fixes:
- CVE-2013-1798
- CVE-2019-3016
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Fri, 21 Feb 2020 14:04:52 +0000 (15:04 +0100)]
kernel: bump 4.14 to 4.14.171
Refreshed all patches.
Fixes:
- CVE-2013-1798
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Sungbo Eo [Sun, 23 Feb 2020 15:17:16 +0000 (00:17 +0900)]
kirkwood: tidy up hwmon_fancontrol
Add indent and sort board_name alphabetically.
Sourcing /lib/functions.sh is already handled by /etc/rc.common. Drop the line.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sun, 23 Feb 2020 12:38:24 +0000 (21:38 +0900)]
urngd: avoid PKG_NAME in define lines
> Avoid reuse of PKG_NAME in call, define and eval lines for consistency and
> readability. Write the full name instead.
Ref: https://openwrt.org/docs/guide-developer/packages
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sun, 23 Feb 2020 12:37:36 +0000 (21:37 +0900)]
urandom-seed: avoid PKG_NAME in define lines
> Avoid reuse of PKG_NAME in call, define and eval lines for consistency and
> readability. Write the full name instead.
Ref: https://openwrt.org/docs/guide-developer/packages
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sun, 23 Feb 2020 15:14:22 +0000 (00:14 +0900)]
kirkwood: add kmod-hwmon-core to DEVICE_PACKAGES
kmod-hwmon-lm* will not get into images unless kmod-hwmon-core is added to
DEVICE_PACKAGES as well.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[only address kmod-hwmon-core in this commit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Sun, 23 Feb 2020 15:16:16 +0000 (00:16 +0900)]
kirkwood: tidy up image Makefile
- use k in SIZE variables
- break long lines
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sun, 23 Feb 2020 15:12:23 +0000 (00:12 +0900)]
kirkwood: fix device node name of Iomega ix2-200
The current device node name of ix2-200 is "iom_ix2_200", which results
in a SUPPORTED_DEVICES string "iom,ix2,200" that does not match the
compatible in DTS and the board name used in board.d.
Fix this by replacing the second underscore with a dash, following
vendor_model scheme.
Fixes:
27b2f0fc0fc5 ("kirkwood: add support for Iomega Storcenter ix2-200")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[commit title/message rephrase]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
David Bauer [Sun, 23 Feb 2020 11:50:30 +0000 (12:50 +0100)]
ath79: fix TP-Link TL-WA901ND v2 PHY stuck in reset
Some newer bootloaders for the TP-Link TL-WA901ND put the ethernet PHY
in reset before loading the kernel, thus the LAN interface is not
working in OpenWrt.
Clear the reset to restore ethernet functionality.
Signed-off-by: David Bauer <mail@david-bauer.net>
Sungbo Eo [Sun, 23 Feb 2020 04:05:35 +0000 (13:05 +0900)]
x86: avoid underscore in package name
As
07e1d88d7beb ("kernel: avoid underscore in *6lowpan package names") shows,
underscores might cause build failures. Replace underscore with dash.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sun, 23 Feb 2020 04:05:27 +0000 (13:05 +0900)]
ltq-vdsl-mei: avoid underscore in package name
As
07e1d88d7beb ("kernel: avoid underscore in *6lowpan package names") shows,
underscores might cause build failures. Replace underscore with dash.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Adrian Schmutzler [Sat, 22 Feb 2020 18:33:41 +0000 (19:33 +0100)]
ramips: move includes to DTSI for mt7628an_tplink_8m*
All devices inherited from mt7628an_tplink_8m.dtsi and
mt7628an_tplink_8m-split-uboot.dtsi contain the same additional
includes in the DTS files.
Move them to the DTSI files instead.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sat, 22 Feb 2020 18:28:17 +0000 (19:28 +0100)]
ramips: move compatible for Ubiquiti Edgerouter X to DTS file
So far, the compatible for the Ubiquiti Edgerouter X has been
defined in the DTSI file and inherited for the edgerouterx.dts,
but overwritten for the edgerouterx-sfp.dts. In contrast, the
model was stored in the DTS file in both cases.
To resolve this somewhat confusing situation, move the compatible
with the device name for edgerouterx to the DTS file as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sat, 22 Feb 2020 18:26:17 +0000 (19:26 +0100)]
ramips: remove redundant includes in DTS files
Many DTS files contain the same includes again that are already
present in the DTSI files they are derived from.
Remove those redundant includes in the DTS files. For vocore, the
include is moved to the parent DTSI file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sat, 22 Feb 2020 18:16:05 +0000 (19:16 +0100)]
ath79: remove redundant includes in DTS files
Many DTS files contain the same includes again that are already
present in the DTSI files they are derived from.
Remove those redundant includes in the DTS files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Scott Roberts [Wed, 22 Jan 2020 22:42:46 +0000 (15:42 -0700)]
packages/boot: bump arm-trusted-firmware-mvebu version
The current version of ATF does not support power off for SGMII
COMPHY. Update to latest ATF to resolve this issue.
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
Fredrik Olofsson [Wed, 29 Jan 2020 14:39:53 +0000 (15:39 +0100)]
mac80211: backport fix TID field in monitor mode transmit
Backport
753ffad3d6243303994227854d951ff5c70fa9e0 as merged in Linux v5.5-rc3.
Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
Martin Schiller [Wed, 5 Feb 2020 07:12:54 +0000 (08:12 +0100)]
kernel: fix xt_connmark.h
Commit
a1cfe0dcbb24 (kernel: connmark set-dscpmark follow upstreamimg
attempt") broke the usage of xt_connmark.h in user-space (e.g.
strongswan), because the BIT() macro is unknown there.
Fixes:
a1cfe0dcbb24 (kernel: connmark set-dscpmark follow upstreamimg attempt")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Daniel Engberg [Mon, 3 Feb 2020 15:30:06 +0000 (15:30 +0000)]
toolchain/binutils: Add binutils 2.34
Refresh patches
Drop 300-012_check_ldrunpath_length.patch
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Daniel Engberg [Tue, 4 Feb 2020 01:10:17 +0000 (01:10 +0000)]
package/utils/f2fs-tools: Update to 1.13.0
Update f2fs-tools to 1.13.0
Remove upstreamed patches
Disable build of static library
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Aleksander Jan Bajkowski [Sun, 9 Feb 2020 15:23:06 +0000 (16:23 +0100)]
generic: refresh patches
just run: make target/linux/refresh V=s
Fixes:
6e315de0f422acf66c3505a4ed8c095a0f5d3424
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Davide Fioravanti [Wed, 19 Feb 2020 18:43:00 +0000 (19:43 +0100)]
usbmode: Update modeswitch data to
20191128
Add support for new hardware
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Aleksander Jan Bajkowski [Tue, 18 Feb 2020 19:32:11 +0000 (20:32 +0100)]
kernel: remove non-existant symbols from 4.19 config
These symbols only exist in kernel version <= 4.15
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Tomasz Maciej Nowak [Mon, 20 Jan 2020 14:42:00 +0000 (15:42 +0100)]
kernel: replace SUBDIRS with M in package recipes
The SUBDIRS variable has been removed in kernel 5.4, and was deprecated
since the beginnig of kernel git history in favour of M or KBUILD_EXTMOD.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
DENG Qingfang [Fri, 14 Feb 2020 13:41:06 +0000 (21:41 +0800)]
linux-firmware: update to
20200122
Update linux-firmware to
20200122
git log --pretty=oneline --abbrev-commit
20191215..
20200122
1eb2408 linux-firmware: Update firmware file for Intel Bluetooth AX200
0dc1611 linux-firmware: Update firmware file for Intel Bluetooth AX201
d03f79c linux-firmware: Update firmware file for Intel Bluetooth 9560
aab62bc linux-firmware: Update firmware file for Intel Bluetooth 9260
ed0aa3a nvidia: add TU102/TU104/TU106 signed firmware
9c340bd amdgpu: update navi10 firmware for 19.50
3b4a503 amdgpu: Add navi10 TA ucode
16cc13a Merge branch 'v1.1.3' of https://github.com/ruiwang-mtk/linux_fw_vpu_v1.1.
37f3177d mediatek: update MT8173 VPU firmware to v1.1.3
67d4ff5 Mellanox: Add new mlxsw_spectrum firmware xx.2000.2714
f1c9e7b radeon: update oland rlc microcode from amdgpu
b1dafb7 amdgpu: update vega20 microcode for 19.50
c38789e amdgpu: update vega12 microcode for 19.50
5a141c1 amdgpu: update vega10 microcode for 19.50
a03173a amdgpu: update picasso microcode for 19.50
86e9a5f amdgpu: update raven2 microcode for 19.50
febe09a amdgpu: update raven microcode for 19.50
af76fd0 amdgpu: update navi10 microcode for 19.50
b5b176a amdgpu: update navi14 microcode for 19.50
ad90178 amdgpu: add TA microcode for Raven asics
379551b qed: Add firmware 8.42.2.0
58b4003 Merge branch 'RB3-wlan-firmware-1387-v2' of https://github.com/andersson/linux-firmware
5967a45 Adjust WHENCE entry to check_whence doesn't complain
d1e743d Merge branch 'master' of https://github.com/NXP/mwifiex-firmware
d6219ab qcom: Switch SDM845 WLAN firmware
e65245c linux-firmware: add NXP firmware licence file
6871bff Merge branch 'ath10k-
20191220' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/linux-firmware
b142c2e ath10k: WCN3990 hw1.0: add firmware WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
8809b87 ath10k: QCA9984 hw1.0: update firmware-5.bin to 10.4-3.9.0.2-00070
513d70c ath10k: QCA988X hw2.0: update firmware-5.bin to 10.2.4-1.0-00047
203435b ath10k: QCA9888 hw2.0: update firmware-5.bin to 10.4-3.9.0.2-00070
a66d2fc ath10k: QCA9887 hw1.0: update firmware-5.bin to 10.2.4-1.0-00047
6d19154 ath10k: QCA6174 hw3.0: update board-2.bin
c4586ff linux-firmware: Update AMD cpu microcode
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Wed, 12 Feb 2020 12:16:05 +0000 (20:16 +0800)]
iw: update to 5.4
Update iw to 5.4
This increases the ipk size of iw-tiny/full by about 400 bytes
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
projects / oweals / openwrt.git / log