--- /dev/null
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "Seagate GoFlex Home";
+ compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ aliases {
+ led-boot = &led_health;
+ led-failsafe = &led_fault;
+ led-running = &led_health;
+ led-upgrade = &led_fault;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
+ stdout-path = &uart0;
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ pmx_usb_power_enable: pmx-usb-power-enable {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+ pmx_led_white: pmx-led-white {
+ marvell,pins = "mpp40";
+ marvell,function = "gpio";
+ };
+ pmx_led_green: pmx-led_green {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+ pmx_led_orange: pmx-led-orange {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ };
+ serial@12000 {
+ status = "ok";
+ };
+
+ sata@80000 {
+ status = "okay";
+ nr-ports = <2>;
+ };
+
+ };
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ led_health: health {
+ label = "status:green:health";
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+ led_fault: fault {
+ label = "status:orange:fault";
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+ misc {
+ label = "status:white:misc";
+ gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "disk-activity";
+ };
+ };
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_usb_power_enable>;
+ pinctrl-names = "default";
+
+ usb_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&nand {
+ chip-delay = <40>;
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "ubi";
+ reg = <0x100000 0x0ff00000>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
--- /dev/null
+/*
+ * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500
+ *
+ * (c) 2013 Jonas Gorski <jogo@openwrt.org>
+ * (c) 2013 Deutsche Telekom Innovation Laboratories
+ * (c) 2014 Luka Perkov <luka@openwrt.org>
+ * (c) 2014 Dan Walters <dan@walters.io>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6282.dtsi"
+
+/ {
+ model = "Linksys Audi (EA3500)";
+ compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x4000000>;
+ };
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >;
+ pinctrl-names = "default";
+
+ wps {
+ label = "WPS Button";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+
+ reset {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = < &pmx_led_green_power >;
+ pinctrl-names = "default";
+
+ led_power: power {
+ label = "audi:green:power";
+ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ mvsw61xx {
+ compatible = "marvell,88e6171";
+ status = "okay";
+ reg = <0x10>;
+
+ mii-bus = <&mdio>;
+ cpu-port-0 = <5>;
+ cpu-port-1 = <6>;
+ is-indirect;
+ };
+
+ dsa {
+ compatible = "marvell,dsa";
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ dsa,ethernet = <ð0port>;
+ dsa,mii-bus = <&mdio>;
+
+ switch@16,0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <16 0>; /* MDIO address 16, switch 0 in tree */
+
+ port@0 {
+ reg = <0>;
+ label = "ethernet1";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "ethernet2";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "ethernet3";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "ethernet4";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "internet";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "cpu";
+ };
+ };
+ };
+};
+
+&pinctrl {
+ pmx_led_green_power: pmx-led-green-power {
+ marvell,pins = "mpp7";
+ marvell,function = "gpo";
+ };
+ pmx_btn_wps: pmx-btn-wps {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ pmx_btn_reset: pmx-btn-reset {
+ marvell,pins = "mpp48";
+ marvell,function = "gpio";
+ };
+};
+
+&nand {
+ status = "okay";
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "u_env";
+ reg = <0x80000 0x4000>;
+ };
+
+ partition@84000 {
+ label = "s_env";
+ reg = <0x84000 0x4000>;
+ };
+
+ partition@200000 {
+ label = "kernel1";
+ reg = <0x200000 0x290000>;
+ };
+
+ partition@490000 {
+ label = "rootfs1";
+ reg = <0x490000 0x1170000>;
+ };
+
+ partition@1600000 {
+ label = "kernel2";
+ reg = <0x1600000 0x290000>;
+ };
+
+ partition@1890000 {
+ label = "rootfs2";
+ reg = <0x1890000 0x1170000>;
+ };
+
+ partition@2a00000 {
+ label = "syscfg";
+ reg = <0x2a00000 0x1600000>;
+ };
+
+ partition@88000 {
+ label = "unused";
+ reg = <0x88000 0x178000>;
+ };
+
+ };
+};
+
+&pciec {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set
+ * fixed speed and duplex.
+ */
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ speed = <1000>;
+ duplex = <1>;
+ };
+};
+
+/* eth1 is connected to the switch at port 6. However DSA only supports a
+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion.
+ */
+ð1 {
+ status = "okay";
+ ethernet1-port@0 {
+ speed = <1000>;
+ duplex = <1>;
+ };
+};
+
+/* There is no battery on the board, so the RTC does not keep
+ * time when there is no power, making it useless.
+ */
+&rtc {
+ status = "disabled";
+};
--- /dev/null
+/dts-v1/;
+
+#include "kirkwood-nsa3x0-common.dtsi"
+
+/*
+ * There are at least two different NSA310 designs. This variant has
+ * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller.
+ */
+
+/ {
+ model = "ZyXEL NSA310b";
+ compatible = "zyxel,nsa310b", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ aliases {
+ led-boot = &led_green_sys;
+ led-failsafe = &led_red_sys;
+ led-running = &led_green_sys;
+ led-upgrade = &led_red_sys;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x10000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ stdout-path = &uart0;
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ pinctrl-names = "default";
+
+ pmx_led_esata_green: pmx-led-esata-green {
+ marvell,pins = "mpp12";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_esata_red: pmx-led-esata-red {
+ marvell,pins = "mpp13";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_usb_green: pmx-led-usb-green {
+ marvell,pins = "mpp15";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_usb_red: pmx-led-usb-red {
+ marvell,pins = "mpp16";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_sys_green: pmx-led-sys-green {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_sys_red: pmx-led-sys-red {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_hdd_green: pmx-led-hdd-green {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_hdd_red: pmx-led-hdd-red {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+
+ };
+
+ i2c@11000 {
+ status = "okay";
+
+ lm85: lm85@2e {
+ compatible = "national,lm85";
+ reg = <0x2e>;
+ };
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ led_green_sys: green-sys {
+ label = "nsa310:green:sys";
+ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ led_red_sys: red-sys {
+ label = "nsa310:red:sys";
+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ };
+ green-hdd {
+ label = "nsa310:green:hdd";
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ };
+ red-hdd {
+ label = "nsa310:red:hdd";
+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ };
+ green-esata {
+ label = "nsa310:green:esata";
+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ };
+ red-esata {
+ label = "nsa310:red:esata";
+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+ };
+ green-usb {
+ label = "nsa310:green:usb";
+ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+ };
+ red-usb {
+ label = "nsa310:red:usb";
+ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+ };
+ green-copy {
+ label = "nsa310:green:copy";
+ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ };
+ red-copy {
+ label = "nsa310:red:copy";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
--- /dev/null
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6282.dtsi"
+
+/ {
+ model = "Cisco Systems ON100";
+ compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>;
+ };
+
+ aliases {
+ led-boot = &led_health_green;
+ led-failsafe = &led_health_red;
+ led-running = &led_health_green;
+ led-upgrade = &led_health_red;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_btn_reset>;
+ pinctrl-names = "default";
+
+ button@1 {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >;
+ pinctrl-names = "default";
+
+ led_health_green: health_green {
+ label = "on100:green:health";
+ gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ led_health_red: health_red {
+ label = "on100:red:health";
+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+ };
+
+ health2_green {
+ label = "on100:green:health2";
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ };
+
+ health2_red {
+ label = "on100:red:health2";
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ phy-connection-type = "rgmii-id";
+ };
+};
+
+ð1 {
+ status = "okay";
+
+ ethernet1-port@0 {
+ phy-handle = <ðphy1>;
+ phy-connection-type = "rgmii-id";
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 {
+ /* Marvell 88E1121R */
+ compatible = "ethernet-phy-id0141.0cb0",
+ "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+
+ ethphy1: ethernet-phy@1 {
+ /* Marvell 88E1121R */
+ compatible = "ethernet-phy-id0141.0cb0",
+ "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x00000000 0x000a0000>;
+ read-only;
+ };
+
+ partition@a0000 {
+ label = "u-boot environment";
+ reg = <0x000a0000 0x00020000>;
+ read-only;
+ };
+
+ partition@c0000 {
+ label = "kernel";
+ reg = <0x000c0000 0x00540000>;
+ };
+
+ partition@600000 {
+ label = "ubi";
+ reg = <0x00600000 0x1fa00000>;
+ };
+};
+
+&pinctrl {
+ pmx_led_health_r: pmx-led-health-r {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_health_g: pmx-led-health-g {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_health2_r: pmx-led-health2-r {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_health2_g: pmx-led-health2-g {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+
+ pmx_btn_reset: pmx-led-reset {
+ marvell,pins = "mpp31";
+ marvell,function = "gpio";
+ };
+};
+
+&sdio {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
--- /dev/null
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "Seagate GoFlex Home";
+ compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ aliases {
+ led-boot = &led_health;
+ led-failsafe = &led_fault;
+ led-running = &led_health;
+ led-upgrade = &led_fault;
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
+ stdout-path = &uart0;
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ pmx_usb_power_enable: pmx-usb-power-enable {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+ pmx_led_white: pmx-led-white {
+ marvell,pins = "mpp40";
+ marvell,function = "gpio";
+ };
+ pmx_led_green: pmx-led_green {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+ pmx_led_orange: pmx-led-orange {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ };
+ serial@12000 {
+ status = "ok";
+ };
+
+ sata@80000 {
+ status = "okay";
+ nr-ports = <2>;
+ };
+
+ };
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ led_health: health {
+ label = "status:green:health";
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+ led_fault: fault {
+ label = "status:orange:fault";
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+ misc {
+ label = "status:white:misc";
+ gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "disk-activity";
+ };
+ };
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_usb_power_enable>;
+ pinctrl-names = "default";
+
+ usb_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&nand {
+ chip-delay = <40>;
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "ubi";
+ reg = <0x100000 0x0ff00000>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500
+ *
+ * (c) 2013 Jonas Gorski <jogo@openwrt.org>
+ * (c) 2013 Deutsche Telekom Innovation Laboratories
+ * (c) 2014 Luka Perkov <luka@openwrt.org>
+ * (c) 2014 Dan Walters <dan@walters.io>
+ *
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6282.dtsi"
+
+/ {
+ model = "Linksys Audi (EA3500)";
+ compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x00000000 0x4000000>;
+ };
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >;
+ pinctrl-names = "default";
+
+ wps {
+ label = "WPS Button";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+
+ reset {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = < &pmx_led_green_power >;
+ pinctrl-names = "default";
+
+ led_power: power {
+ label = "audi:green:power";
+ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ switches {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mvsw61xx@10 {
+ compatible = "marvell,88e6171";
+ status = "okay";
+ reg = <0x10>;
+
+ mii-bus = <&mdio>;
+ cpu-port-0 = <5>;
+ cpu-port-1 = <6>;
+ is-indirect;
+ };
+ };
+
+ dsa {
+ compatible = "marvell,dsa";
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ dsa,ethernet = <ð0port>;
+ dsa,mii-bus = <&mdio>;
+
+ switch@16,0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <16 0>; /* MDIO address 16, switch 0 in tree */
+
+ port@0 {
+ reg = <0>;
+ label = "ethernet1";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "ethernet2";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "ethernet3";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "ethernet4";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "internet";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "cpu";
+ };
+ };
+ };
+};
+
+&pinctrl {
+ pmx_led_green_power: pmx-led-green-power {
+ marvell,pins = "mpp7";
+ marvell,function = "gpo";
+ };
+ pmx_btn_wps: pmx-btn-wps {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ pmx_btn_reset: pmx-btn-reset {
+ marvell,pins = "mpp48";
+ marvell,function = "gpio";
+ };
+};
+
+&nand {
+ status = "okay";
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "u_env";
+ reg = <0x80000 0x4000>;
+ };
+
+ partition@84000 {
+ label = "s_env";
+ reg = <0x84000 0x4000>;
+ };
+
+ partition@200000 {
+ label = "kernel1";
+ reg = <0x200000 0x290000>;
+ };
+
+ partition@490000 {
+ label = "rootfs1";
+ reg = <0x490000 0x1170000>;
+ };
+
+ partition@1600000 {
+ label = "kernel2";
+ reg = <0x1600000 0x290000>;
+ };
+
+ partition@1890000 {
+ label = "rootfs2";
+ reg = <0x1890000 0x1170000>;
+ };
+
+ partition@2a00000 {
+ label = "syscfg";
+ reg = <0x2a00000 0x1600000>;
+ };
+
+ partition@88000 {
+ label = "unused";
+ reg = <0x88000 0x178000>;
+ };
+
+ };
+};
+
+&pciec {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set
+ * fixed speed and duplex.
+ */
+ð0 {
+ status = "okay";
+ ethernet0-port@0 {
+ speed = <1000>;
+ duplex = <1>;
+ };
+};
+
+/* eth1 is connected to the switch at port 6. However DSA only supports a
+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion.
+ */
+ð1 {
+ status = "okay";
+ ethernet1-port@0 {
+ speed = <1000>;
+ duplex = <1>;
+ };
+};
+
+/* There is no battery on the board, so the RTC does not keep
+ * time when there is no power, making it useless.
+ */
+&rtc {
+ status = "disabled";
+};
--- /dev/null
+/dts-v1/;
+
+#include "kirkwood-nsa3x0-common.dtsi"
+
+/*
+ * There are at least two different NSA310 designs. This variant has
+ * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller.
+ */
+
+/ {
+ model = "ZyXEL NSA310b";
+ compatible = "zyxel,nsa310b", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ aliases {
+ led-boot = &led_green_sys;
+ led-failsafe = &led_red_sys;
+ led-running = &led_green_sys;
+ led-upgrade = &led_red_sys;
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x00000000 0x10000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ stdout-path = &uart0;
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ pinctrl-names = "default";
+
+ pmx_led_esata_green: pmx-led-esata-green {
+ marvell,pins = "mpp12";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_esata_red: pmx-led-esata-red {
+ marvell,pins = "mpp13";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_usb_green: pmx-led-usb-green {
+ marvell,pins = "mpp15";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_usb_red: pmx-led-usb-red {
+ marvell,pins = "mpp16";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_sys_green: pmx-led-sys-green {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_sys_red: pmx-led-sys-red {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_hdd_green: pmx-led-hdd-green {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_hdd_red: pmx-led-hdd-red {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+
+ };
+
+ i2c@11000 {
+ status = "okay";
+
+ lm85: lm85@2e {
+ compatible = "national,lm85";
+ reg = <0x2e>;
+ };
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ led_green_sys: green-sys {
+ label = "nsa310:green:sys";
+ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ led_red_sys: red-sys {
+ label = "nsa310:red:sys";
+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ };
+ green-hdd {
+ label = "nsa310:green:hdd";
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ };
+ red-hdd {
+ label = "nsa310:red:hdd";
+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ };
+ green-esata {
+ label = "nsa310:green:esata";
+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ };
+ red-esata {
+ label = "nsa310:red:esata";
+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+ };
+ green-usb {
+ label = "nsa310:green:usb";
+ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+ };
+ red-usb {
+ label = "nsa310:red:usb";
+ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+ };
+ green-copy {
+ label = "nsa310:green:copy";
+ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ };
+ red-copy {
+ label = "nsa310:red:copy";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
--- /dev/null
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6282.dtsi"
+
+/ {
+ model = "Cisco Systems ON100";
+ compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>;
+ };
+
+ aliases {
+ led-boot = &led_health_green;
+ led-failsafe = &led_health_red;
+ led-running = &led_health_green;
+ led-upgrade = &led_health_red;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&pmx_btn_reset>;
+ pinctrl-names = "default";
+
+ reset {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >;
+ pinctrl-names = "default";
+
+ led_health_green: health_green {
+ label = "on100:green:health";
+ gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+
+ led_health_red: health_red {
+ label = "on100:red:health";
+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+ };
+
+ health2_green {
+ label = "on100:green:health2";
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ };
+
+ health2_red {
+ label = "on100:red:health2";
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ phy-connection-type = "rgmii-id";
+ };
+};
+
+ð1 {
+ status = "okay";
+
+ ethernet1-port@0 {
+ phy-handle = <ðphy1>;
+ phy-connection-type = "rgmii-id";
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 {
+ /* Marvell 88E1121R */
+ compatible = "ethernet-phy-id0141.0cb0",
+ "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+
+ ethphy1: ethernet-phy@1 {
+ /* Marvell 88E1121R */
+ compatible = "ethernet-phy-id0141.0cb0",
+ "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x00000000 0x000a0000>;
+ read-only;
+ };
+
+ partition@a0000 {
+ label = "u-boot environment";
+ reg = <0x000a0000 0x00020000>;
+ read-only;
+ };
+
+ partition@c0000 {
+ label = "kernel";
+ reg = <0x000c0000 0x00540000>;
+ };
+
+ partition@600000 {
+ label = "ubi";
+ reg = <0x00600000 0x1fa00000>;
+ };
+};
+
+&pinctrl {
+ pmx_led_health_r: pmx-led-health-r {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_health_g: pmx-led-health-g {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_health2_r: pmx-led-health2-r {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_health2_g: pmx-led-health2-g {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+
+ pmx_btn_reset: pmx-led-reset {
+ marvell,pins = "mpp31";
+ marvell,function = "gpio";
+ };
+};
+
+&sdio {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+++ /dev/null
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -250,6 +250,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-linkstation-lswsxl.dtb \
- kirkwood-linkstation-lswvl.dtb \
- kirkwood-linkstation-lswxl.dtb \
-+ kirkwood-linksys-audi.dtb \
- kirkwood-linksys-viper.dtb \
- kirkwood-lschlv2.dtb \
- kirkwood-lsxhl.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-linksys-audi.dts
-@@ -0,0 +1,250 @@
-+/*
-+ * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500
-+ *
-+ * (c) 2013 Jonas Gorski <jogo@openwrt.org>
-+ * (c) 2013 Deutsche Telekom Innovation Laboratories
-+ * (c) 2014 Luka Perkov <luka@openwrt.org>
-+ * (c) 2014 Dan Walters <dan@walters.io>
-+ *
-+ * This file is licensed under the terms of the GNU General Public
-+ * License version 2. This program is licensed "as is" without any
-+ * warranty of any kind, whether express or implied.
-+ */
-+
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6282.dtsi"
-+
-+/ {
-+ model = "Linksys Audi (EA3500)";
-+ compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood";
-+
-+ memory {
-+ device_type = "memory";
-+ reg = <0x00000000 0x4000000>;
-+ };
-+
-+ aliases {
-+ led-boot = &led_power;
-+ led-failsafe = &led_power;
-+ led-running = &led_power;
-+ led-upgrade = &led_power;
-+ serial0 = &uart0;
-+ };
-+
-+ chosen {
-+ stdout-path = "serial0:115200n8";
-+ };
-+
-+ gpio_keys {
-+ compatible = "gpio-keys";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >;
-+ pinctrl-names = "default";
-+
-+ wps {
-+ label = "WPS Button";
-+ linux,code = <KEY_WPS_BUTTON>;
-+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-+ };
-+
-+ reset {
-+ label = "Reset Button";
-+ linux,code = <KEY_RESTART>;
-+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
-+ };
-+ };
-+
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+ pinctrl-0 = < &pmx_led_green_power >;
-+ pinctrl-names = "default";
-+
-+ led_power: power {
-+ label = "audi:green:power";
-+ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
-+ default-state = "on";
-+ };
-+ };
-+
-+ mvsw61xx {
-+ compatible = "marvell,88e6171";
-+ status = "okay";
-+ reg = <0x10>;
-+
-+ mii-bus = <&mdio>;
-+ cpu-port-0 = <5>;
-+ cpu-port-1 = <6>;
-+ is-indirect;
-+ };
-+
-+ dsa {
-+ compatible = "marvell,dsa";
-+ #address-cells = <2>;
-+ #size-cells = <0>;
-+
-+ dsa,ethernet = <ð0port>;
-+ dsa,mii-bus = <&mdio>;
-+
-+ switch@16,0 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <16 0>; /* MDIO address 16, switch 0 in tree */
-+
-+ port@0 {
-+ reg = <0>;
-+ label = "ethernet1";
-+ };
-+
-+ port@1 {
-+ reg = <1>;
-+ label = "ethernet2";
-+ };
-+
-+ port@2 {
-+ reg = <2>;
-+ label = "ethernet3";
-+ };
-+
-+ port@3 {
-+ reg = <3>;
-+ label = "ethernet4";
-+ };
-+
-+ port@4 {
-+ reg = <4>;
-+ label = "internet";
-+ };
-+
-+ port@5 {
-+ reg = <5>;
-+ label = "cpu";
-+ };
-+ };
-+ };
-+};
-+
-+&pinctrl {
-+ pmx_led_green_power: pmx-led-green-power {
-+ marvell,pins = "mpp7";
-+ marvell,function = "gpo";
-+ };
-+ pmx_btn_wps: pmx-btn-wps {
-+ marvell,pins = "mpp47";
-+ marvell,function = "gpio";
-+ };
-+ pmx_btn_reset: pmx-btn-reset {
-+ marvell,pins = "mpp48";
-+ marvell,function = "gpio";
-+ };
-+};
-+
-+&nand {
-+ status = "okay";
-+ pinctrl-0 = <&pmx_nand>;
-+ pinctrl-names = "default";
-+
-+ partitions {
-+ compatible = "fixed-partitions";
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+
-+ partition@0 {
-+ label = "u-boot";
-+ reg = <0x0 0x80000>;
-+ read-only;
-+ };
-+
-+ partition@80000 {
-+ label = "u_env";
-+ reg = <0x80000 0x4000>;
-+ };
-+
-+ partition@84000 {
-+ label = "s_env";
-+ reg = <0x84000 0x4000>;
-+ };
-+
-+ partition@200000 {
-+ label = "kernel1";
-+ reg = <0x200000 0x290000>;
-+ };
-+
-+ partition@490000 {
-+ label = "rootfs1";
-+ reg = <0x490000 0x1170000>;
-+ };
-+
-+ partition@1600000 {
-+ label = "kernel2";
-+ reg = <0x1600000 0x290000>;
-+ };
-+
-+ partition@1890000 {
-+ label = "rootfs2";
-+ reg = <0x1890000 0x1170000>;
-+ };
-+
-+ partition@2a00000 {
-+ label = "syscfg";
-+ reg = <0x2a00000 0x1600000>;
-+ };
-+
-+ partition@88000 {
-+ label = "unused";
-+ reg = <0x88000 0x178000>;
-+ };
-+
-+ };
-+};
-+
-+&pciec {
-+ status = "okay";
-+};
-+
-+&pcie0 {
-+ status = "okay";
-+};
-+
-+&pcie1 {
-+ status = "okay";
-+};
-+
-+&mdio {
-+ status = "okay";
-+};
-+
-+&uart0 {
-+ status = "okay";
-+};
-+
-+/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set
-+ * fixed speed and duplex.
-+ */
-+ð0 {
-+ status = "okay";
-+ ethernet0-port@0 {
-+ speed = <1000>;
-+ duplex = <1>;
-+ };
-+};
-+
-+/* eth1 is connected to the switch at port 6. However DSA only supports a
-+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion.
-+ */
-+ð1 {
-+ status = "okay";
-+ ethernet1-port@0 {
-+ speed = <1000>;
-+ duplex = <1>;
-+ };
-+};
-+
-+/* There is no battery on the board, so the RTC does not keep
-+ * time when there is no power, making it useless.
-+ */
-+&rtc {
-+ status = "disabled";
-+};
+++ /dev/null
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -237,6 +237,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-ds411.dtb \
- kirkwood-ds411j.dtb \
- kirkwood-ds411slim.dtb \
-+ kirkwood-goflexhome.dtb \
- kirkwood-goflexnet.dtb \
- kirkwood-guruplug-server-plus.dtb \
- kirkwood-ib62x0.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-goflexhome.dts
-@@ -0,0 +1,124 @@
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6281.dtsi"
-+
-+/ {
-+ model = "Seagate GoFlex Home";
-+ compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+
-+ aliases {
-+ led-boot = &led_health;
-+ led-failsafe = &led_fault;
-+ led-running = &led_health;
-+ led-upgrade = &led_fault;
-+ };
-+
-+ memory {
-+ device_type = "memory";
-+ reg = <0x00000000 0x8000000>;
-+ };
-+
-+ chosen {
-+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
-+ stdout-path = &uart0;
-+ };
-+
-+ ocp@f1000000 {
-+ pinctrl: pin-controller@10000 {
-+ pmx_usb_power_enable: pmx-usb-power-enable {
-+ marvell,pins = "mpp29";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_white: pmx-led-white {
-+ marvell,pins = "mpp40";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_green: pmx-led_green {
-+ marvell,pins = "mpp46";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_orange: pmx-led-orange {
-+ marvell,pins = "mpp47";
-+ marvell,function = "gpio";
-+ };
-+ };
-+ serial@12000 {
-+ status = "ok";
-+ };
-+
-+ sata@80000 {
-+ status = "okay";
-+ nr-ports = <2>;
-+ };
-+
-+ };
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+
-+ led_health: health {
-+ label = "status:green:health";
-+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
-+ default-state = "on";
-+ };
-+ led_fault: fault {
-+ label = "status:orange:fault";
-+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-+ };
-+ misc {
-+ label = "status:white:misc";
-+ gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
-+ linux,default-trigger = "disk-activity";
-+ };
-+ };
-+ regulators {
-+ compatible = "simple-bus";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-0 = <&pmx_usb_power_enable>;
-+ pinctrl-names = "default";
-+
-+ usb_power: regulator@1 {
-+ compatible = "regulator-fixed";
-+ reg = <1>;
-+ regulator-name = "USB Power";
-+ regulator-min-microvolt = <5000000>;
-+ regulator-max-microvolt = <5000000>;
-+ enable-active-high;
-+ regulator-always-on;
-+ regulator-boot-on;
-+ gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
-+ };
-+ };
-+};
-+
-+&nand {
-+ chip-delay = <40>;
-+ status = "okay";
-+
-+ partition@0 {
-+ label = "u-boot";
-+ reg = <0x0000000 0x100000>;
-+ read-only;
-+ };
-+
-+ partition@100000 {
-+ label = "ubi";
-+ reg = <0x100000 0x0ff00000>;
-+ };
-+};
-+
-+&mdio {
-+ status = "okay";
-+
-+ ethphy0: ethernet-phy@0 {
-+ reg = <0>;
-+ };
-+};
-+
-+ð0 {
-+ status = "okay";
-+ ethernet0-port@0 {
-+ phy-handle = <ðphy0>;
-+ };
-+};
+++ /dev/null
-kirkwood: add nsa310b dtb, a zyxel nsa310 variant
-
-add support to a nsa310 variant with red/green usb led
-and lm85 temp/fan controller
-
-Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
-
-NOTE: this patch can be upstreamed as-is, LEDE-specific
- nand partitions are set in another patch
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -268,6 +268,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-ns2mini.dtb \
- kirkwood-nsa310.dtb \
- kirkwood-nsa310a.dtb \
-+ kirkwood-nsa310b.dtb \
- kirkwood-nsa320.dtb \
- kirkwood-nsa325.dtb \
- kirkwood-openblocks_a6.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-nsa310b.dts
-@@ -0,0 +1,132 @@
-+/dts-v1/;
-+
-+#include "kirkwood-nsa3x0-common.dtsi"
-+
-+/*
-+ * There are at least two different NSA310 designs. This variant has
-+ * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller.
-+ */
-+
-+/ {
-+ model = "ZyXEL NSA310b";
-+ compatible = "zyxel,nsa310b", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+
-+ aliases {
-+ led-boot = &led_green_sys;
-+ led-failsafe = &led_red_sys;
-+ led-running = &led_green_sys;
-+ led-upgrade = &led_red_sys;
-+ };
-+
-+ memory {
-+ device_type = "memory";
-+ reg = <0x00000000 0x10000000>;
-+ };
-+
-+ chosen {
-+ bootargs = "console=ttyS0,115200";
-+ stdout-path = &uart0;
-+ };
-+
-+ ocp@f1000000 {
-+ pinctrl: pin-controller@10000 {
-+ pinctrl-names = "default";
-+
-+ pmx_led_esata_green: pmx-led-esata-green {
-+ marvell,pins = "mpp12";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_esata_red: pmx-led-esata-red {
-+ marvell,pins = "mpp13";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_usb_green: pmx-led-usb-green {
-+ marvell,pins = "mpp15";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_usb_red: pmx-led-usb-red {
-+ marvell,pins = "mpp16";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_sys_green: pmx-led-sys-green {
-+ marvell,pins = "mpp28";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_sys_red: pmx-led-sys-red {
-+ marvell,pins = "mpp29";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_hdd_green: pmx-led-hdd-green {
-+ marvell,pins = "mpp41";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_hdd_red: pmx-led-hdd-red {
-+ marvell,pins = "mpp42";
-+ marvell,function = "gpio";
-+ };
-+
-+ };
-+
-+ i2c@11000 {
-+ status = "okay";
-+
-+ lm85: lm85@2e {
-+ compatible = "national,lm85";
-+ reg = <0x2e>;
-+ };
-+ };
-+ };
-+
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+
-+ led_green_sys: green-sys {
-+ label = "nsa310:green:sys";
-+ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
-+ default-state = "on";
-+ };
-+ led_red_sys: red-sys {
-+ label = "nsa310:red:sys";
-+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
-+ };
-+ green-hdd {
-+ label = "nsa310:green:hdd";
-+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
-+ };
-+ red-hdd {
-+ label = "nsa310:red:hdd";
-+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
-+ };
-+ green-esata {
-+ label = "nsa310:green:esata";
-+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
-+ };
-+ red-esata {
-+ label = "nsa310:red:esata";
-+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
-+ };
-+ green-usb {
-+ label = "nsa310:green:usb";
-+ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
-+ };
-+ red-usb {
-+ label = "nsa310:red:usb";
-+ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
-+ };
-+ green-copy {
-+ label = "nsa310:green:copy";
-+ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
-+ };
-+ red-copy {
-+ label = "nsa310:red:copy";
-+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
-+ };
-+ };
-+};
+++ /dev/null
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-on100.dts
-@@ -0,0 +1,165 @@
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6282.dtsi"
-+
-+/ {
-+ model = "Cisco Systems ON100";
-+ compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood";
-+
-+ memory {
-+ device_type = "memory";
-+ reg = <0x00000000 0x20000000>;
-+ };
-+
-+ aliases {
-+ led-boot = &led_health_green;
-+ led-failsafe = &led_health_red;
-+ led-running = &led_health_green;
-+ led-upgrade = &led_health_red;
-+ serial0 = &uart0;
-+ };
-+
-+ chosen {
-+ bootargs = "console=ttyS0,115200n8 earlyprintk";
-+ stdout-path = "serial0:115200n8";
-+ };
-+
-+ gpio_keys {
-+ compatible = "gpio-keys";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-0 = <&pmx_btn_reset>;
-+ pinctrl-names = "default";
-+
-+ button@1 {
-+ label = "Reset Button";
-+ linux,code = <KEY_RESTART>;
-+ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
-+ };
-+ };
-+
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+ pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >;
-+ pinctrl-names = "default";
-+
-+ led_health_green: health_green {
-+ label = "on100:green:health";
-+ gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
-+ default-state = "on";
-+ };
-+
-+ led_health_red: health_red {
-+ label = "on100:red:health";
-+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
-+ };
-+
-+ health2_green {
-+ label = "on100:green:health2";
-+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
-+ };
-+
-+ health2_red {
-+ label = "on100:red:health2";
-+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-+ };
-+ };
-+};
-+
-+ð0 {
-+ status = "okay";
-+
-+ ethernet0-port@0 {
-+ phy-handle = <ðphy0>;
-+ phy-connection-type = "rgmii-id";
-+ };
-+};
-+
-+ð1 {
-+ status = "okay";
-+
-+ ethernet1-port@0 {
-+ phy-handle = <ðphy1>;
-+ phy-connection-type = "rgmii-id";
-+ };
-+};
-+
-+&mdio {
-+ status = "okay";
-+
-+ ethphy0: ethernet-phy@0 {
-+ /* Marvell 88E1121R */
-+ compatible = "ethernet-phy-id0141.0cb0",
-+ "ethernet-phy-ieee802.3-c22";
-+ reg = <0>;
-+ };
-+
-+ ethphy1: ethernet-phy@1 {
-+ /* Marvell 88E1121R */
-+ compatible = "ethernet-phy-id0141.0cb0",
-+ "ethernet-phy-ieee802.3-c22";
-+ reg = <1>;
-+ };
-+};
-+
-+&nand {
-+ status = "okay";
-+
-+ partition@0 {
-+ label = "u-boot";
-+ reg = <0x00000000 0x000a0000>;
-+ read-only;
-+ };
-+
-+ partition@a0000 {
-+ label = "u-boot environment";
-+ reg = <0x000a0000 0x00020000>;
-+ read-only;
-+ };
-+
-+ partition@c0000 {
-+ label = "kernel";
-+ reg = <0x000c0000 0x00540000>;
-+ };
-+
-+ partition@600000 {
-+ label = "ubi";
-+ reg = <0x00600000 0x1fa00000>;
-+ };
-+};
-+
-+&pinctrl {
-+ pmx_led_health_r: pmx-led-health-r {
-+ marvell,pins = "mpp45";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_health_g: pmx-led-health-g {
-+ marvell,pins = "mpp44";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_health2_r: pmx-led-health2-r {
-+ marvell,pins = "mpp47";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_health2_g: pmx-led-health2-g {
-+ marvell,pins = "mpp46";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_btn_reset: pmx-led-reset {
-+ marvell,pins = "mpp31";
-+ marvell,function = "gpio";
-+ };
-+};
-+
-+&sdio {
-+ status = "okay";
-+};
-+
-+&uart0 {
-+ status = "okay";
-+};
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -271,6 +271,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-nsa310b.dtb \
- kirkwood-nsa320.dtb \
- kirkwood-nsa325.dtb \
-+ kirkwood-on100.dtb \
- kirkwood-openblocks_a6.dtb \
- kirkwood-openblocks_a7.dtb \
- kirkwood-openrd-base.dtb \
+++ /dev/null
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -269,6 +269,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-linkstation-lswsxl.dtb \
- kirkwood-linkstation-lswvl.dtb \
- kirkwood-linkstation-lswxl.dtb \
-+ kirkwood-linksys-audi.dtb \
- kirkwood-linksys-viper.dtb \
- kirkwood-lschlv2.dtb \
- kirkwood-lsxhl.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-linksys-audi.dts
-@@ -0,0 +1,251 @@
-+// SPDX-License-Identifier: GPL-2.0
-+/*
-+ * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500
-+ *
-+ * (c) 2013 Jonas Gorski <jogo@openwrt.org>
-+ * (c) 2013 Deutsche Telekom Innovation Laboratories
-+ * (c) 2014 Luka Perkov <luka@openwrt.org>
-+ * (c) 2014 Dan Walters <dan@walters.io>
-+ *
-+ */
-+
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6282.dtsi"
-+
-+/ {
-+ model = "Linksys Audi (EA3500)";
-+ compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood";
-+
-+ memory@0 {
-+ device_type = "memory";
-+ reg = <0x00000000 0x4000000>;
-+ };
-+
-+ aliases {
-+ led-boot = &led_power;
-+ led-failsafe = &led_power;
-+ led-running = &led_power;
-+ led-upgrade = &led_power;
-+ serial0 = &uart0;
-+ };
-+
-+ chosen {
-+ stdout-path = "serial0:115200n8";
-+ };
-+
-+ gpio_keys {
-+ compatible = "gpio-keys";
-+ pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >;
-+ pinctrl-names = "default";
-+
-+ wps {
-+ label = "WPS Button";
-+ linux,code = <KEY_WPS_BUTTON>;
-+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-+ };
-+
-+ reset {
-+ label = "Reset Button";
-+ linux,code = <KEY_RESTART>;
-+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
-+ };
-+ };
-+
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+ pinctrl-0 = < &pmx_led_green_power >;
-+ pinctrl-names = "default";
-+
-+ led_power: power {
-+ label = "audi:green:power";
-+ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
-+ default-state = "on";
-+ };
-+ };
-+
-+ switches {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ mvsw61xx@10 {
-+ compatible = "marvell,88e6171";
-+ status = "okay";
-+ reg = <0x10>;
-+
-+ mii-bus = <&mdio>;
-+ cpu-port-0 = <5>;
-+ cpu-port-1 = <6>;
-+ is-indirect;
-+ };
-+ };
-+
-+ dsa {
-+ compatible = "marvell,dsa";
-+ #address-cells = <2>;
-+ #size-cells = <0>;
-+
-+ dsa,ethernet = <ð0port>;
-+ dsa,mii-bus = <&mdio>;
-+
-+ switch@16,0 {
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ reg = <16 0>; /* MDIO address 16, switch 0 in tree */
-+
-+ port@0 {
-+ reg = <0>;
-+ label = "ethernet1";
-+ };
-+
-+ port@1 {
-+ reg = <1>;
-+ label = "ethernet2";
-+ };
-+
-+ port@2 {
-+ reg = <2>;
-+ label = "ethernet3";
-+ };
-+
-+ port@3 {
-+ reg = <3>;
-+ label = "ethernet4";
-+ };
-+
-+ port@4 {
-+ reg = <4>;
-+ label = "internet";
-+ };
-+
-+ port@5 {
-+ reg = <5>;
-+ label = "cpu";
-+ };
-+ };
-+ };
-+};
-+
-+&pinctrl {
-+ pmx_led_green_power: pmx-led-green-power {
-+ marvell,pins = "mpp7";
-+ marvell,function = "gpo";
-+ };
-+ pmx_btn_wps: pmx-btn-wps {
-+ marvell,pins = "mpp47";
-+ marvell,function = "gpio";
-+ };
-+ pmx_btn_reset: pmx-btn-reset {
-+ marvell,pins = "mpp48";
-+ marvell,function = "gpio";
-+ };
-+};
-+
-+&nand {
-+ status = "okay";
-+ pinctrl-0 = <&pmx_nand>;
-+ pinctrl-names = "default";
-+
-+ partitions {
-+ compatible = "fixed-partitions";
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+
-+ partition@0 {
-+ label = "u-boot";
-+ reg = <0x0 0x80000>;
-+ read-only;
-+ };
-+
-+ partition@80000 {
-+ label = "u_env";
-+ reg = <0x80000 0x4000>;
-+ };
-+
-+ partition@84000 {
-+ label = "s_env";
-+ reg = <0x84000 0x4000>;
-+ };
-+
-+ partition@200000 {
-+ label = "kernel1";
-+ reg = <0x200000 0x290000>;
-+ };
-+
-+ partition@490000 {
-+ label = "rootfs1";
-+ reg = <0x490000 0x1170000>;
-+ };
-+
-+ partition@1600000 {
-+ label = "kernel2";
-+ reg = <0x1600000 0x290000>;
-+ };
-+
-+ partition@1890000 {
-+ label = "rootfs2";
-+ reg = <0x1890000 0x1170000>;
-+ };
-+
-+ partition@2a00000 {
-+ label = "syscfg";
-+ reg = <0x2a00000 0x1600000>;
-+ };
-+
-+ partition@88000 {
-+ label = "unused";
-+ reg = <0x88000 0x178000>;
-+ };
-+
-+ };
-+};
-+
-+&pciec {
-+ status = "okay";
-+};
-+
-+&pcie0 {
-+ status = "okay";
-+};
-+
-+&pcie1 {
-+ status = "okay";
-+};
-+
-+&mdio {
-+ status = "okay";
-+};
-+
-+&uart0 {
-+ status = "okay";
-+};
-+
-+/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set
-+ * fixed speed and duplex.
-+ */
-+ð0 {
-+ status = "okay";
-+ ethernet0-port@0 {
-+ speed = <1000>;
-+ duplex = <1>;
-+ };
-+};
-+
-+/* eth1 is connected to the switch at port 6. However DSA only supports a
-+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion.
-+ */
-+ð1 {
-+ status = "okay";
-+ ethernet1-port@0 {
-+ speed = <1000>;
-+ duplex = <1>;
-+ };
-+};
-+
-+/* There is no battery on the board, so the RTC does not keep
-+ * time when there is no power, making it useless.
-+ */
-+&rtc {
-+ status = "disabled";
-+};
+++ /dev/null
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -256,6 +256,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-ds411.dtb \
- kirkwood-ds411j.dtb \
- kirkwood-ds411slim.dtb \
-+ kirkwood-goflexhome.dtb \
- kirkwood-goflexnet.dtb \
- kirkwood-guruplug-server-plus.dtb \
- kirkwood-ib62x0.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-goflexhome.dts
-@@ -0,0 +1,124 @@
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6281.dtsi"
-+
-+/ {
-+ model = "Seagate GoFlex Home";
-+ compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+
-+ aliases {
-+ led-boot = &led_health;
-+ led-failsafe = &led_fault;
-+ led-running = &led_health;
-+ led-upgrade = &led_fault;
-+ };
-+
-+ memory@0 {
-+ device_type = "memory";
-+ reg = <0x00000000 0x8000000>;
-+ };
-+
-+ chosen {
-+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
-+ stdout-path = &uart0;
-+ };
-+
-+ ocp@f1000000 {
-+ pinctrl: pin-controller@10000 {
-+ pmx_usb_power_enable: pmx-usb-power-enable {
-+ marvell,pins = "mpp29";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_white: pmx-led-white {
-+ marvell,pins = "mpp40";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_green: pmx-led_green {
-+ marvell,pins = "mpp46";
-+ marvell,function = "gpio";
-+ };
-+ pmx_led_orange: pmx-led-orange {
-+ marvell,pins = "mpp47";
-+ marvell,function = "gpio";
-+ };
-+ };
-+ serial@12000 {
-+ status = "ok";
-+ };
-+
-+ sata@80000 {
-+ status = "okay";
-+ nr-ports = <2>;
-+ };
-+
-+ };
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+
-+ led_health: health {
-+ label = "status:green:health";
-+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
-+ default-state = "on";
-+ };
-+ led_fault: fault {
-+ label = "status:orange:fault";
-+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-+ };
-+ misc {
-+ label = "status:white:misc";
-+ gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
-+ linux,default-trigger = "disk-activity";
-+ };
-+ };
-+ regulators {
-+ compatible = "simple-bus";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ pinctrl-0 = <&pmx_usb_power_enable>;
-+ pinctrl-names = "default";
-+
-+ usb_power: regulator@1 {
-+ compatible = "regulator-fixed";
-+ reg = <1>;
-+ regulator-name = "USB Power";
-+ regulator-min-microvolt = <5000000>;
-+ regulator-max-microvolt = <5000000>;
-+ enable-active-high;
-+ regulator-always-on;
-+ regulator-boot-on;
-+ gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
-+ };
-+ };
-+};
-+
-+&nand {
-+ chip-delay = <40>;
-+ status = "okay";
-+
-+ partition@0 {
-+ label = "u-boot";
-+ reg = <0x0000000 0x100000>;
-+ read-only;
-+ };
-+
-+ partition@100000 {
-+ label = "ubi";
-+ reg = <0x100000 0x0ff00000>;
-+ };
-+};
-+
-+&mdio {
-+ status = "okay";
-+
-+ ethphy0: ethernet-phy@0 {
-+ reg = <0>;
-+ };
-+};
-+
-+ð0 {
-+ status = "okay";
-+ ethernet0-port@0 {
-+ phy-handle = <ðphy0>;
-+ };
-+};
+++ /dev/null
-kirkwood: add nsa310b dtb, a zyxel nsa310 variant
-
-add support to a nsa310 variant with red/green usb led
-and lm85 temp/fan controller
-
-Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
-
-NOTE: this patch can be upstreamed as-is, LEDE-specific
- nand partitions are set in another patch
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -287,6 +287,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-ns2mini.dtb \
- kirkwood-nsa310.dtb \
- kirkwood-nsa310a.dtb \
-+ kirkwood-nsa310b.dtb \
- kirkwood-nsa320.dtb \
- kirkwood-nsa325.dtb \
- kirkwood-openblocks_a6.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-nsa310b.dts
-@@ -0,0 +1,132 @@
-+/dts-v1/;
-+
-+#include "kirkwood-nsa3x0-common.dtsi"
-+
-+/*
-+ * There are at least two different NSA310 designs. This variant has
-+ * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller.
-+ */
-+
-+/ {
-+ model = "ZyXEL NSA310b";
-+ compatible = "zyxel,nsa310b", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-+
-+ aliases {
-+ led-boot = &led_green_sys;
-+ led-failsafe = &led_red_sys;
-+ led-running = &led_green_sys;
-+ led-upgrade = &led_red_sys;
-+ };
-+
-+ memory@0 {
-+ device_type = "memory";
-+ reg = <0x00000000 0x10000000>;
-+ };
-+
-+ chosen {
-+ bootargs = "console=ttyS0,115200";
-+ stdout-path = &uart0;
-+ };
-+
-+ ocp@f1000000 {
-+ pinctrl: pin-controller@10000 {
-+ pinctrl-names = "default";
-+
-+ pmx_led_esata_green: pmx-led-esata-green {
-+ marvell,pins = "mpp12";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_esata_red: pmx-led-esata-red {
-+ marvell,pins = "mpp13";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_usb_green: pmx-led-usb-green {
-+ marvell,pins = "mpp15";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_usb_red: pmx-led-usb-red {
-+ marvell,pins = "mpp16";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_sys_green: pmx-led-sys-green {
-+ marvell,pins = "mpp28";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_sys_red: pmx-led-sys-red {
-+ marvell,pins = "mpp29";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_hdd_green: pmx-led-hdd-green {
-+ marvell,pins = "mpp41";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_hdd_red: pmx-led-hdd-red {
-+ marvell,pins = "mpp42";
-+ marvell,function = "gpio";
-+ };
-+
-+ };
-+
-+ i2c@11000 {
-+ status = "okay";
-+
-+ lm85: lm85@2e {
-+ compatible = "national,lm85";
-+ reg = <0x2e>;
-+ };
-+ };
-+ };
-+
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+
-+ led_green_sys: green-sys {
-+ label = "nsa310:green:sys";
-+ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
-+ default-state = "on";
-+ };
-+ led_red_sys: red-sys {
-+ label = "nsa310:red:sys";
-+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
-+ };
-+ green-hdd {
-+ label = "nsa310:green:hdd";
-+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
-+ };
-+ red-hdd {
-+ label = "nsa310:red:hdd";
-+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
-+ };
-+ green-esata {
-+ label = "nsa310:green:esata";
-+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
-+ };
-+ red-esata {
-+ label = "nsa310:red:esata";
-+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
-+ };
-+ green-usb {
-+ label = "nsa310:green:usb";
-+ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
-+ };
-+ red-usb {
-+ label = "nsa310:red:usb";
-+ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
-+ };
-+ green-copy {
-+ label = "nsa310:green:copy";
-+ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
-+ };
-+ red-copy {
-+ label = "nsa310:red:copy";
-+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
-+ };
-+ };
-+};
+++ /dev/null
---- /dev/null
-+++ b/arch/arm/boot/dts/kirkwood-on100.dts
-@@ -0,0 +1,163 @@
-+/dts-v1/;
-+
-+#include "kirkwood.dtsi"
-+#include "kirkwood-6282.dtsi"
-+
-+/ {
-+ model = "Cisco Systems ON100";
-+ compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood";
-+
-+ memory@0 {
-+ device_type = "memory";
-+ reg = <0x00000000 0x20000000>;
-+ };
-+
-+ aliases {
-+ led-boot = &led_health_green;
-+ led-failsafe = &led_health_red;
-+ led-running = &led_health_green;
-+ led-upgrade = &led_health_red;
-+ serial0 = &uart0;
-+ };
-+
-+ chosen {
-+ bootargs = "console=ttyS0,115200n8 earlyprintk";
-+ stdout-path = "serial0:115200n8";
-+ };
-+
-+ gpio_keys {
-+ compatible = "gpio-keys";
-+ pinctrl-0 = <&pmx_btn_reset>;
-+ pinctrl-names = "default";
-+
-+ reset {
-+ label = "Reset Button";
-+ linux,code = <KEY_RESTART>;
-+ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
-+ };
-+ };
-+
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+ pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >;
-+ pinctrl-names = "default";
-+
-+ led_health_green: health_green {
-+ label = "on100:green:health";
-+ gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
-+ default-state = "on";
-+ };
-+
-+ led_health_red: health_red {
-+ label = "on100:red:health";
-+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
-+ };
-+
-+ health2_green {
-+ label = "on100:green:health2";
-+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
-+ };
-+
-+ health2_red {
-+ label = "on100:red:health2";
-+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-+ };
-+ };
-+};
-+
-+ð0 {
-+ status = "okay";
-+
-+ ethernet0-port@0 {
-+ phy-handle = <ðphy0>;
-+ phy-connection-type = "rgmii-id";
-+ };
-+};
-+
-+ð1 {
-+ status = "okay";
-+
-+ ethernet1-port@0 {
-+ phy-handle = <ðphy1>;
-+ phy-connection-type = "rgmii-id";
-+ };
-+};
-+
-+&mdio {
-+ status = "okay";
-+
-+ ethphy0: ethernet-phy@0 {
-+ /* Marvell 88E1121R */
-+ compatible = "ethernet-phy-id0141.0cb0",
-+ "ethernet-phy-ieee802.3-c22";
-+ reg = <0>;
-+ };
-+
-+ ethphy1: ethernet-phy@1 {
-+ /* Marvell 88E1121R */
-+ compatible = "ethernet-phy-id0141.0cb0",
-+ "ethernet-phy-ieee802.3-c22";
-+ reg = <1>;
-+ };
-+};
-+
-+&nand {
-+ status = "okay";
-+
-+ partition@0 {
-+ label = "u-boot";
-+ reg = <0x00000000 0x000a0000>;
-+ read-only;
-+ };
-+
-+ partition@a0000 {
-+ label = "u-boot environment";
-+ reg = <0x000a0000 0x00020000>;
-+ read-only;
-+ };
-+
-+ partition@c0000 {
-+ label = "kernel";
-+ reg = <0x000c0000 0x00540000>;
-+ };
-+
-+ partition@600000 {
-+ label = "ubi";
-+ reg = <0x00600000 0x1fa00000>;
-+ };
-+};
-+
-+&pinctrl {
-+ pmx_led_health_r: pmx-led-health-r {
-+ marvell,pins = "mpp45";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_health_g: pmx-led-health-g {
-+ marvell,pins = "mpp44";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_health2_r: pmx-led-health2-r {
-+ marvell,pins = "mpp47";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_led_health2_g: pmx-led-health2-g {
-+ marvell,pins = "mpp46";
-+ marvell,function = "gpio";
-+ };
-+
-+ pmx_btn_reset: pmx-led-reset {
-+ marvell,pins = "mpp31";
-+ marvell,function = "gpio";
-+ };
-+};
-+
-+&sdio {
-+ status = "okay";
-+};
-+
-+&uart0 {
-+ status = "okay";
-+};
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -290,6 +290,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
- kirkwood-nsa310b.dtb \
- kirkwood-nsa320.dtb \
- kirkwood-nsa325.dtb \
-+ kirkwood-on100.dtb \
- kirkwood-openblocks_a6.dtb \
- kirkwood-openblocks_a7.dtb \
- kirkwood-openrd-base.dtb \
projects / oweals / openwrt.git / commitdiff