David Bauer [Fri, 13 Dec 2019 20:31:50 +0000 (21:31 +0100)]
mpc85xx: add support for Enterasys WS-AP3710i
Hardware
--------
SoC: NXP P1020 (2x e500 @ 800MHz)
RAM: 256M DDR3 (Micron)
FLASH: 32M NOR (Spansion S29GL128S)
BTN: 1x Reset
WiFi: 1x Atheros AR9590 2.4 bgn 3x3
2x Atheros AR9590 5.0 an 3x3
ETH: 1x Gigabit Ethernet (Atheros AR8033)
LED: System (green/red) - Radio{0,1} (green)
LAN (connected to PHY)
- GE blue
- FE green
Serial is a Cisco-compatible RJ45 next to the ethernet port.
115200-N-8 are the settings for OS and U-Boot.
Installation
------------
1. Grab the OpenWrt initramfs, rename it to
01C8A8C0.img. Place it in
the root directory of a TFTP server and serve it at
192.168.200.200/24.
2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot
by pressing Enter when prompted. Credentials are identical to the one
in the APs interface. By default it is admin / new2day.
3. Set the bootcmd so the AP can boot OpenWrt by executing
$ setenv boot_openwrt "setenv bootargs;
cp.b 0xee000000 0x1000000 0x1000000; bootm 0x1000000"
$ setenv bootcmd "run boot_openwrt"
$ saveenv
If you plan on going back to the vendor firmware - the bootcmd for it
is stored in the boot_flash variable.
4. Load the initramfs image to RAM and boot by executing
$ tftpboot 0x1000000 192.168.200.200:
01C8A8C0.img; bootm
5. Make a backup of the "firmware" partition if you ever wish to go back
to the vendor firmware.
6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp
folder.
7. Flash OpenWrt using sysupgrade.
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
DENG Qingfang [Fri, 13 Dec 2019 16:24:19 +0000 (00:24 +0800)]
ramips: add support for JCG JHR-AC876M
JCG JHR-AC876M is an AC2600M router
Hardware specs:
SoC: MT7621AT
2.4GHz: MT7615N 4x4 @ PCIe0
5GHz: MT7615N 4x4 @ PCIe1
Flash: Winbond W25Q128JVSQ 16MiB
RAM: Nanya NT5CB128M16 256MiB
USB 2.0 and 3.0 ports
6 LEDs, 3 of which are connected to SoC GPIO
Reset and WPS buttons
Flash instructions:
Stock to OpenWrt:
Upload factory.bin in stock firmware's upgrade page,
do not preserve settings
OpenWrt to stock:
Push and hold the reset button for 5s while power cycling to
enter recovery mode;
Visit 192.168.1.1 and upload stock firmware
MAC addresses map:
0x0004 *:1c wlan2g/wan/label
0x8004 *:20 wlan5g
0xe000 *:1b lan
0xe006 *:1a not used in stock fw
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Adrian Schmutzler [Thu, 12 Dec 2019 19:26:06 +0000 (20:26 +0100)]
ramips: allow JCG_MAXSIZE in kiB in Build/jcg-header
This allows JCG_MAXSIZE to be specified in kilobytes. This makes
this value more consistent and easier comparable with other size
variables.
This also changes the only occurence of the variable, for Cudy WR1000.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Mon, 11 Nov 2019 16:25:31 +0000 (01:25 +0900)]
ramips: add support for ipTIME A6ns-M
ipTIME A6ns-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7615
- 5GHz: MT7615
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- UART:
- J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Adrian Schmutzler [Thu, 12 Dec 2019 18:49:55 +0000 (19:49 +0100)]
ramips: DTS style improvements for mt7621_wevo_w2914ns-v2.dtsi
This does several trivial DTS style improvements:
- Move device name compatible to DTS files (and fix compatible in
11acnas.dts)
- Remove xhci node as status is set to okay in mt7621.dtsi already
- 0x0 instead of 0x0000
- Simplify state_default node definition
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Mon, 11 Nov 2019 16:26:44 +0000 (01:26 +0900)]
ramips: add support for ZIO FREEZIO
ZIO FREEZIO is a 2.4/5GHz band AC1200 router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7603EN
- 5GHz: MT7612EN
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- USB: 1x 3.0
- UART:
- J4: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1
Notes:
- FREEZIO has almost the same board as WeVO W2914NS v2.
- Stock firmware is based on OpenWrt BB.
MAC addresses in factory partition:
0x0004: WiFi 2.4GHz (label_mac-8)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-4)
0xe000: LAN (label_mac+1)
Installation via web interface:
1. Access web admin page and turn on "OpenWrt UI mode".
2. Flash sysupgrade image through LuCI, with the "Keep settings" option
OFF.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Make sure to NOT preserve settings.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebase, use mt7621_wevo_w2914ns-v2.dtsi]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Roman Bazalevsky [Thu, 5 Dec 2019 14:21:28 +0000 (17:21 +0300)]
sunxi: add support for FriendlyARM Nano PI NEO Air dev board
Hardware:
Allwinner H3 upto 1.2GHz
512MB DDR3 RAM
8GB on-board eMMC - mountable, can be used as boot with custom boot.scr
microSD-card slot
WiFi 802.11n (AP6212A) - working
Bluetooth (AP6212A) - not working for now
Micro-USB OTG + 2*USB headers
UART 3.3V - working
GPIO/I2C/SPI 2.54mm headers
Standard sunxi SD-card installation procedure - copy image to SD card,
insert in into slot and boot. First time you will need UART adapter to
enable on-board wireless (or just build custom image with enabled WiFi).
To boot from eMMC:
- boot from SD
- copy SD image to emmc (dd bs=... if=.... of=/dev/mmcblk2)
- mount eMMC boot partition and replace boot script on it
- unmount, reboot
To use i2c, spi and more uarts - replace dtb on boot partition with
fixed one (use dtc or fdt-tools).
Signed-off-by: Roman Bazalevsky <rvb@rvb.name>
[rebase onto device name consolidation patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Thu, 5 Dec 2019 23:47:18 +0000 (00:47 +0100)]
sunxi: construct DTS name from device node name and SOC
The device part in the SUNXI_DTS variable always corresponds to
device node name. This is another redundancy that can be removed
by calculating the DTS name from a newly introduced SUNXI_SOC
variable and the node name.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Thu, 5 Dec 2019 23:11:56 +0000 (00:11 +0100)]
sunxi: use vendor_device scheme for device definitions
This changes device definition to resemble the vendor_device scheme
already present for the majority of device compatible strings.
By doing this, we achieve several advantages at once:
- Image names and node names are more consistent with other targets.
- SUPPORTED_DEVICES can be set automatically for all but two cases.
- Image names and node names are in line with DEVICE_TITLEs.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Mon, 9 Dec 2019 12:53:21 +0000 (13:53 +0100)]
ath79: add support for TP-Link TL-WDR4300 v1 (IL)
The TL-WDR4300 v1 sold in Israel has a different TPLINK_HWID.
Thanks to Josh4300 for testing on device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Fri, 6 Dec 2019 12:56:51 +0000 (13:56 +0100)]
ath79: redistribute UBNT variables in Ubiquiti image Makefile
The variables UBNT_BOARD and UBNT_VERSION are defined in the parent
Device/ubnt definition and then overwritten for most of the derived
platform definitions (e.g. Device/ubnt-wa).
Since this mixed use of inheritance and overwriting can be misleading,
this moves the variables to the platform-based definitions.
While at it, reorder the definitions to have order consistent, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Mon, 9 Dec 2019 11:56:12 +0000 (12:56 +0100)]
ramips: add label MAC address for Mikrotik RBM33G
The device label contains:
E01: B8:69:F4:xx:xx:07
E02: B8:69:F4:xx:xx:09
The first value corresponds to the address set in hard_config 0x10.
That one is taken for the label MAC address.
Thanks to Martin Schiller for retrieving the information.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 8 Dec 2019 15:15:00 +0000 (16:15 +0100)]
ramips: rt305x: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
This removes the wan_mac setup for the following devices as they
do not set up a MAC address for ethernet in the first place:
- asiarf,awapn2403
- belkin,f7c027
- dlink,dir-615-d
- mofinetwork,mofi3500-3gn
- prolink,pwh2004
- ralink,v22rw-2x2
- unbranded,wr512-3gn-4m
- unbranded,wr512-3gn-8m
While at it, make some DT node labels consistent with the label
property.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 8 Dec 2019 13:55:49 +0000 (14:55 +0100)]
ramips: rt288x: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
This removes the wan_mac setup for ralink,v11st-fe as this device
does not set up a MAC address for ethernet in the first place.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 8 Dec 2019 13:26:34 +0000 (14:26 +0100)]
ramips: mt76x8: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
While at it, change the partition label for zyxel,keenetic-extra-ii
to factory to be consistent with node label and all the other devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 8 Dec 2019 12:42:39 +0000 (13:42 +0100)]
ramips: mt7621: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 8 Dec 2019 12:20:50 +0000 (13:20 +0100)]
ramips: mt7620: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 8 Dec 2019 12:23:56 +0000 (13:23 +0100)]
ramips: remove wan_mac setup for evaluation boards
The evaluation boards do not set up a MAC address for eth0
in the first place, so it does not make sense to calculate a WAN
address from the random MAC used there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 8 Dec 2019 11:51:20 +0000 (12:51 +0100)]
ramips: create common DTSI for TP-Link Archer C20i/C20 v1/C50 v1
The TP-Link Archer C20i/C20 v1/C50 v1 seem to be almost the same,
so creating a common DTSI will reduce duplicate code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sat, 7 Dec 2019 22:37:40 +0000 (23:37 +0100)]
ramips: remove unused DTS variable from DEVICE_VARS
The DTS variable has been removed in
402138d12dca ("ramips: Derive
DTS name from device name in Makefile"), but the DEVICE_VARS entry
has been overlooked.
Remove it now since we are not using this variable.
This must _not_ be backported to 19.07, where the variable is still
in use.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Gabor Varga [Mon, 9 Dec 2019 22:03:58 +0000 (23:03 +0100)]
ramips: fix switch port numbering for RT-AC65P/RT-AC85P
The switch LAN port numbers are in reversed order with original config.
With this patch they are fixed.
Port order checked on both devices.
Signed-off-by: Gabor Varga <vargagab@gmail.com>
[merged definitions into appropriate block, extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 8 Dec 2019 11:28:22 +0000 (12:28 +0100)]
ramips: add label MAC address for TP-Link Archer C20i
Current OpenWrt MAC setup:
eth0 &rom 0xf100 :48
eth0.2 eth0+1 :49
wlan0 (5 GHz) &radio 0x8004 different OUI
wlan1 (2.4 GHz) &radio 0x4 same OUI as wlan0
Label MAC address corresponds to eth0 (ðernet).
No additional addresses found in hexdump of rom/radio.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
DENG Qingfang [Sat, 7 Dec 2019 16:37:31 +0000 (00:37 +0800)]
ath79: fix typos in DTS
Replace "usb_ochi" with "usb_ohci", and "usb_echi" with "usb_ehci".
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Hans Dedecker [Wed, 11 Dec 2019 21:27:26 +0000 (22:27 +0100)]
glibc: update to latest 2.27 commit (BZ #2503, BZ #2504)
bef0b1cb31 libio: Disable vtable validation for pre-2.1 interposed handles [BZ #25203]
4d5cfeb510 rtld: Check __libc_enable_secure before honoring LD_PREFER_MAP_32BIT_EXEC (CVE-2019-19126) [BZ #25204]
92f04eedb5 mips: Force RWX stack for hard-float builds that can run on pre-4.8 kernels
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Koen Vandeputte [Mon, 9 Dec 2019 10:47:01 +0000 (11:47 +0100)]
ath10k-firmware: update Candela Tech firmware images
The release notes since last time for wave-1:
* November 29, 2019: Fix IBSS merge issue, related to TSF id leakage bug in firmware code.
Thanks for Ahmed Zaki @ Mage-Networks for helping to diagnose and test.
The release notes since last time for wave-2:
* December 6, 2019: Fix 160Mhz problem caused by logic that did not take into account the fact that
160Mhz has only 1/2 of the NSS of lower bandwidths in the rate table.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Fri, 6 Dec 2019 15:25:06 +0000 (16:25 +0100)]
kernel: bump 4.19 to 4.19.88
Refreshed all patches.
Remove upstreamed:
- 0004-boot-sq201-from-sda1.patch
- 500-v4.20-ubifs-Fix-default-compression-selection-in-ubifs.patch
- 0003-usb-dwc2-use-a-longer-core-rest-timeout-in-dwc2_core.patch
Altered patches:
- 0011-ARM-dts-Fix-up-SQ201-flash-access.patch
- 400-mtd-add-rootfs-split-support.patch
- 0101-pci-mediatek-backport-fix-pcie.patch
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Fri, 6 Dec 2019 13:55:57 +0000 (14:55 +0100)]
kernel: bump 4.14 to 4.14.158
Refreshed all patches.
Altered patches:
- 400-mtd-add-rootfs-split-support.patch
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Fri, 6 Dec 2019 13:06:33 +0000 (14:06 +0100)]
kernel: bump 4.9 to 4.9.206
Refreshed all patches.
Altered patches:
- 400-mtd-add-rootfs-split-support.patch
Compile-tested on: none
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Daniel Golle [Mon, 9 Dec 2019 19:16:53 +0000 (20:16 +0100)]
malta: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 9 Dec 2019 19:15:36 +0000 (20:15 +0100)]
sunxi: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 9 Dec 2019 19:15:02 +0000 (20:15 +0100)]
layerscape: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 9 Dec 2019 19:13:41 +0000 (20:13 +0100)]
kirkwood: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 9 Dec 2019 19:12:41 +0000 (20:12 +0100)]
at91: disable legacy PTYs and virtual terminals
Enabling legacy PTYs causes problems with procd-hotplug.
And as this is a headless target, no need to have virtual terminals.
Remove corresponding kernel config options, they are disabled in
generic kernel config.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 9 Dec 2019 19:11:18 +0000 (20:11 +0100)]
mpc85xx: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 9 Dec 2019 19:10:18 +0000 (20:10 +0100)]
ixp4xx: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 9 Dec 2019 19:09:13 +0000 (20:09 +0100)]
uml: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 9 Dec 2019 19:07:00 +0000 (20:07 +0100)]
oxnas: disable legacy PTYs and virtual terminals
Enabling legacy PTYs causes problems with procd-hotplug.
And as this is a headless target, no need to have virtual terminals.
Remove corresponding kernel config options, they are disabled in
generic kernel config.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 5 Dec 2019 20:17:58 +0000 (21:17 +0100)]
mac80211: don't call md5sum on non-existing file
If no AP is configured, hostapd-${phy}.conf is not being created,
hence md5sum fails and causes log pollution:
netifd: radio1 (3183): md5sum: can't open '/var/run/hostapd-phy1.conf': No such file or directoy
Hence make sure the file exists when calling md5sum.
Fixes:
a5bc9787d4 ("mac80211: add support for dynamically reconfiguring wifi")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 5 Dec 2019 17:35:36 +0000 (18:35 +0100)]
hostapd: re-introduce process tracking
Before commit
60fb4c92b6 ("hostapd: add ubus reload") netifd was
tracking hostapd/wpa_supplicant and restarting wifi in case of a
process crash. Restore this behaviour by tracking the PIDs of
hostapd and wpa_supplicant.
Also make sure hostapd and/or wpa_supplicant have been started before
emmitting ubus calls to them using ubus wait_for.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 5 Dec 2019 17:22:55 +0000 (18:22 +0100)]
mac80211: track unmanaged interfaces
In addition to wpa_supplicant and hostapd managed interfaces, also
track unmanaged interfaces. This is used to make sure that running
'wifi' always returns into a clean state regardless of what the user
did before.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Wed, 4 Dec 2019 23:26:53 +0000 (00:26 +0100)]
hostapd: manage instances via procd instead of pidfile
Allows graceful restart of crashing hostapd/wpa_supplicant instances
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: attempt to launch only present services]
Felix Fietkau [Wed, 4 Dec 2019 23:01:28 +0000 (00:01 +0100)]
hostapd: fix crash regression triggered by mesh mode
Fixes:
60fb4c92b6 ("hostapd: add ubus reload")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: polish commit message]
Adrian Schmutzler [Sat, 23 Nov 2019 10:44:51 +0000 (11:44 +0100)]
treewide: remove dts-v1 identifier from DTSI files
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.
This removes the identifier from all DTSI files in /target/linux.
Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx
This does not touch ipq806x for now, as the bump to 4.19 is close.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
David Bauer [Thu, 5 Dec 2019 18:29:14 +0000 (19:29 +0100)]
hostapd: enable CTRL_IFACE_MIB for hostapd-full
This enables the CTRL_IFACE_MIB symbol for wpad-full and hostapd-full.
If it is not enabled, statistic outputs such as "hostapd_cli all_sta"
are empty.
Signed-off-by: David Bauer <mail@david-bauer.net>
Olli Asikainen [Fri, 15 Nov 2019 15:07:37 +0000 (17:07 +0200)]
brcm47xx: add switch configuration for WNR3500L
Netgear WNR3500L is an already supported device, but out of the
box, the device has no switch configuration and there is no wan.
The correct configuration for this specific model is similar to
some other models. This simple commit adds the correct switch
and the out-of-the-box experience is improved.
Experimentally determined:
Port 0 => WAN
Port 1..4 => LAN
Port 5..7 => unused
Port 8 => CPU
Signed-off-by: Olli Asikainen <olli.asikainen@gmail.com>
Tested-by: Fabian Zaremba <fabian@youremail.eu>
[added port mapping to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sat, 7 Dec 2019 23:09:25 +0000 (00:09 +0100)]
ramips: convert mediatek,mtd-eeprom from decimal to hex notation
A small subset of devices uses decimal notation for mediatek,mtd-eeprom
in DTS files. Convert to hexadecimal notation to be consistent with
all the rest.
Also change "0" to "0x0" in the same files for consistency.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Martin Schiller [Wed, 4 Dec 2019 09:43:02 +0000 (10:43 +0100)]
ramips: fix number of LAN Ports for Mikrotik RBM33G
The Mikrotik RBM33G has only 2 LAN ports.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[moved node in 02_network to maintain alphabetic sorting]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Walter Sonius [Wed, 4 Dec 2019 20:07:58 +0000 (21:07 +0100)]
ramips: fix switch port order for TP-Link Archer C20i
Physical port order watched from the backside of the C20i
(from left to right) is: Internet / 1 / 2 / 3 / 4
Physical Port Switch port
WAN 0
LAN 3 1
LAN 4 2
LAN 1 3
LAN 2 4
(not used) 5
CPU 6
Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[commit message/title improvements]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Christian Lamparter [Wed, 15 Aug 2018 15:53:48 +0000 (17:53 +0200)]
ath79: fix WNDR3700/WNDR3800 wifi reg size
"[...] the size component shall be zero."
(See "PCI Bus Binding to: IEEE Std 1275-1994 Rev 2.1"
section "4.1.1 Open Firmware-defined Properties for Child Nodes")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hans Dedecker [Thu, 5 Dec 2019 21:46:50 +0000 (22:46 +0100)]
iproute2: update to 5.4.0
Update iproute2 to latest stable version, see https://lwn.net/Articles/805654/
for the changes in 5.4.0
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
John Crispin [Thu, 5 Dec 2019 09:22:56 +0000 (10:22 +0100)]
mediatek: fix pcie bringup issue
Signed-off-by: John Crispin <john@phrozen.org>
Jason A. Donenfeld [Thu, 5 Dec 2019 10:59:41 +0000 (11:59 +0100)]
wireguard: bump to 0.0.
20191205
* wg-quick: linux: suppress error when finding unused table
This fixes a spurious warning messages seen with recent versions of iproute2
and kernels.
* wg-quick: linux: ensure postdown hooks execute
* wg-quick: linux: have remove_iptables return true
* wg-quick: linux: iptables-* -w is not widely supported
Adding in iptables had some hiccups. For the record, I'm very unhappy about
having to put any firewalling code into wg-quick(8). We'll of course need to
support nftables too at some point if this continues. I'm investigating with
upstream the possibility of adding a sysctl to patch the issue that iptables
is handling now, so hopefully at somepoint down the line we'll be able to shed
this dependency once again.
* send: use kfree_skb_list
* device: prepare skb_list_walk_safe for upstreaming
* send: avoid touching skb->{next,prev} directly
Suggestions from LKML.
* ipc: make sure userspace communication frees wgdevice
Free things properly on error paths.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Stijn Tintel [Fri, 12 Apr 2019 17:21:58 +0000 (20:21 +0300)]
ath79: add support for Ubiquiti LiteBeam AC Gen2
Hardware:
* SoC: Atheros AR9342-BL1A
* RAM: 64MB DDR2 (Winbond W9751G6KB-25)
* Flash: 16MB SPI NOR (Macronix MX25L12835FZ2I-10G)
* Ethernet: 1x 10/100/1000 Mbps (Atheros AR8035-A) with 24V PoE support
* Wifi 2.4GHz: Atheros AR9340 v2
* WiFi 5GHz: Ubiquiti U-AME-G1-BR4A (rebranded QCA988X v2)
* LEDs: 1x Power, 1x Ethernet
* Buttons: 1x Reset
* UART: 1x TTL 115200n8, 3.3V RX TX GND, 3.3V pin closest to RJ45 port
The LEDs do not seem to be connected to any GPIO, so there is currently
no way to control them.
Installation via U-Boot, TFTP and serial console:
* Configure your TFTP server with IP 192.168.1.254
* Connect serial console and power up the device
* Hit any key to stop autoboot
* tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin
* bootm 0x81000000
* copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin
to /tmp
* sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Stijn Tintel [Tue, 3 Dec 2019 11:57:20 +0000 (13:57 +0200)]
ath79: drop IMAGE/factory.bin from ubnt-wa devices
The sysupgrade image contains OpenWrt specific metadata. Having this
metadata in the factory images makes no sense. Drop IMAGE/factory.bin
from Device/ubnt-wa and use the default from Device/ubnt instead.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Kevin Darbyshire-Bryant [Wed, 4 Dec 2019 12:06:26 +0000 (12:06 +0000)]
kernel: act_ctinfo: fix updated backport on 4.14
It turns out my 4.14 testing had a rather large flaw in it and the
'extack' mechanism isn't quite ready. Remove the extack stuff from this
backport.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kevin Darbyshire-Bryant [Tue, 26 Nov 2019 08:45:38 +0000 (08:45 +0000)]
kernel: act_ctinfo: update backport
Since the original backports from kernel 5.3 a few things have been
tweaked by kernel bumps & other upstream changes. Update the backport
to reflect upstream as closely as possible and remove the bitrot.
Functions remain the same, error reporting improved.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Adrian Schmutzler [Tue, 19 Nov 2019 14:24:58 +0000 (15:24 +0100)]
ath79: fix source of label MAC address for Ubiquiti XM devices
In
d421a8b94489 ("ath79: read label MAC address from flash instead
of using phy0/phy1") the source of the label MAC address was changed
for devices just reading it from phy0. To get rid of the dependency
from phy startup, addresses were read directly from the flash
locations that are used to initialize the phy MAC addresses.
Unfortunately, it turned out that Ubiquiti XM devices seem to have
different flash locations than expected, and also seem to have
specific locations for different devices (all in art/EEPROM):
0xe012 AR9280 Nanostation M2 - 0x120c
0xe035 AR9280 Nanostation M3 - 0x120c
0xe1b2 AR9280 Rocket M2 - 0x120c
0xe1c3 AR9280 Rocket M3 - 0x120c
0xe1b5 AR9280 Rocket M5 - 0x120c
0xe2d5 AR9280 Bullet M2 Titanium - 0x120c
0xe2b5 AR9280 Nanobridge M5 - 0x120c
0xe202 AR9280 Bullet M2 - 0x120c
0xe232 AR9287 Nanobridge M2 - 0x110c
0xe4a2 AR9285 AirRouter - 0xa0bf
Picostation M2 - 0x120c and 0xa0bf
Nanostation Loco M2 - not in 0x120c, other locations not checked
An additional problem of the Ubiquiti device support in OpenWrt is
that we provide images that match several subvariants of the devices,
which might have different MAC address locations.
Given that reading the address from phy0 in 02_network _is_ working
for the ath79 target in general, it does not seem reasonable to
rebuild a complex MAC address retrieval mechanism which is already
present in the ath9k driver.
So, this patch reverts the label MAC address source for Ubiquiti XM
devices (and the Unifi AP) to /sys/class/ieee80211/phy0/macaddress.
This doesn't affect XW and Unifi AC devices, where the label MAC
address source is defined via device tree.
For alfa-network,ap121f the location 0x1002 is kept, as this has
been verified during device support preparation in PR #2199.
Fixes:
d421a8b94489 ("ath79: read label MAC address from flash
instead of using phy0/phy1")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Alin Nastac [Tue, 12 Nov 2019 14:11:00 +0000 (15:11 +0100)]
gre: add ipv6 parameter to gre interfaces
IPv6 protocol is enabled on all gre interfaces, but gre(v6)tap
interfaces are usually added to a bridge interface, in which case
IPv6 should be enabled only on the bridge interface.
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
Hans Dedecker [Mon, 2 Dec 2019 19:42:46 +0000 (20:42 +0100)]
curl: bump to 7.67.0
For changes in 7.67.0; see https://curl.haxx.se/changes.html#7_67_0
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Stijn Tintel [Sat, 30 Nov 2019 18:17:42 +0000 (20:17 +0200)]
octeon: fix sysupgrade
Sysupgrade was failing due to incorrect replacement of backticks:
/sbin/sysupgrade: /lib/upgrade/platform.sh: line 101: syntax error: missing '))'
Fixes:
0bbfc3dff719 ("octeon: replace backticks by $(...)")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
David Bauer [Sun, 24 Nov 2019 19:53:39 +0000 (20:53 +0100)]
generic ar8xxx: increase VLAN table for AR83x7
The Atheros AR8327 and AR8337 have (according to their datasheet) a
VLAN table with a maximum of 4096 entries.
Currently, there's a hard limit of 128 VLANs, which is the same as
for most other Atheros switches. Increase this limit only for the
AR83x7 series and modify some shared functions to allow them to work
with a variable max VLAN count.
Signed-off-by: David Bauer <mail@david-bauer.net>
Christian Lamparter [Sat, 16 Nov 2019 16:08:07 +0000 (17:08 +0100)]
mac80211: switch to upstream owl-loader driver
The Owl Loader (named after the codename that Atheros gave
these devices back in the day) has been accepted upstream.
This patch removes the "misc" driver OpenWrt had and adds
the remaining differences against the version that ships
with 5.4-rc1 into a separate "120-owl-loader-compat.patch"
file that can be cut down once AR71XX is being dealt with.
Note: I decided to keep the existing (kmod-)owl-loader
package name around for now. The kernel module file in
the kmod package will be called ath9k_pci_owl_loader.ko
though.
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Satadru Pramanik [Fri, 15 Nov 2019 17:42:44 +0000 (12:42 -0500)]
busybox: add glibc dependency for vi regex option
Build with musl libc fails with BUSYBOX_DEFAULT_FEATURE_VI_REGEX_SEARCH
enabled. Enabling BusyBox's vi regex search option depends upon GNU
regex. Musl libc does not support GNU regex[1].
So this patch adds explicit dependency on GNU libc and while at it
remove the FIXME comment.
1. https://wiki.musl-libc.org/functional-differences-from-glibc.html
Ref: https://dev.archive.openwrt.org/ticket/21741.html
Ref: https://forum.openwrt.org/t/busybox-not-compiling/
Ref: https://github.com/openwrt/packages/issues/4453
Signed-off-by: Satadru Pramanik <satadru@umich.edu>
[commit subject/description tweaks, From: fix, USE_GLIBC fix, removed comments]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Alin Nastac [Thu, 21 Nov 2019 13:06:18 +0000 (14:06 +0100)]
glibc: backport fix for regexec buffer read overrun
Problem found by AddressSanitizer[1]:
Latest `grep` (git commit
1019e6e) compiled with asan may cause a
heap-buffer-overflow when `-i` is specified.
./grep -i '\(\(\)*.\)*\(\)\(\)\1' /bin/chvt
=================================================================
==16206==ERROR: AddressSanitizer: heap-buffer-overflow on address
1. https://debbugs.gnu.org/34140
Ref: https://sourceware.org/bugzilla/show_bug.cgi?id=24114
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
[commit title and description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
DENG Qingfang [Mon, 14 Oct 2019 07:48:32 +0000 (15:48 +0800)]
Revert "mt76: probe load mt7615 driver asynchronously"
This reverts commit
81764319637f ("mt76: probe load mt7615 driver
asynchronously"). After said commit, users report that MT7615 no longer
works on boot and they have to manually enable WiFi (via command "wifi") to
make it working again.
Fixes: FS#2546
Ref: https://forum.openwrt.org/t/xiaomi-r3p-no-wifi-on-boot/45509
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Robert Marko [Mon, 25 Nov 2019 14:25:00 +0000 (15:25 +0100)]
ipq40xx: add support for Crisis Innovation Lab MeshPoint.One
MeshPoint.One is Wi-Fi hotspot and smart IoT gateway (based upon
Jalapeno module from 8Devices).
MeshPoint.One (https://meshpointone.com) is a unique Wi-Fi hotspot and
smart city gateway that can be installed and powered from street
lighting (even solar power in the future). MeshPoint provides up to 27
hours of interrupted Wi-Fi and IoT services from internal battery even
when external power is not available. MeshPoint.One can be used for
disaster relief efforts in order to provide instant Wi-Fi coverage that
can be easily expanded by just adding more devices that create wide area
mesh network. MeshPoint.One devices have standard Luci UI for
management.
Features:
- 1x 1Gpbs WAN
- 1x 1Gbps LAN
- POE input (eth0)
- POE output (eth1)
- Sensor for temperature, humidity and pressure (Bosch BME280)
- current, voltage and power measurement via TI INA230
- Hardware real time clock
- optional power via Li-Ion battery
- micro USB port with USB to serial chip for easy OpenWrt terminal
access
- I2C header for connecting additional sensors
Installation:
-------------
Simply flash the sysupgrade image from stock firmware.
Or use the built in Web recovery into bootloader:
Hold Reset button for 5 to 20 seconds or use UART and httpd command.
Web UI will appear on 192.168.2.100 by default.
For web recovery use the factory.ubi image.
Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
Signed-off-by: Damir Franusic <damir.franusic@sartura.hr>
Signed-off-by: Valent Turkovic <valent@meshpoint.me>
Signed-off-by: Robert Marko <robert@meshpoint.me>
[commit description long line wrap, usb->USB]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Robert Marko [Mon, 25 Nov 2019 14:12:24 +0000 (15:12 +0100)]
ipq40xx: use DTSI for Jalapeno
Lets move common code for Jalapeno into DTSI, this way Jalapeno based
boards don't introduce duplicate code.
While at it, lets also fix some style issues and update to current DTS
style.
Signed-off-by: Robert Marko <robert@meshpoint.me>
[commit description long line wrap]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hans Dedecker [Fri, 29 Nov 2019 20:53:21 +0000 (21:53 +0100)]
netifd: update to latest git HEAD
e45b140 interface: warn if ip6hint is truncated
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Santiago Piccinini [Mon, 25 Nov 2019 19:53:59 +0000 (16:53 -0300)]
mac80211: unify setup of iw htmode for mesh and adhoc
This also fixes mac80211_prepare_vif iw set channel in monitor or
mesh mode.
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: fixed commit message]
Koen Vandeputte [Fri, 29 Nov 2019 09:52:01 +0000 (10:52 +0100)]
kernel: bump 4.9 to 4.9.205
Refreshed all patches.
Fixes:
- CVE-2019-18660
Compile-tested on: none
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 25 Nov 2019 10:32:08 +0000 (11:32 +0100)]
kernel: bump 4.19 to 4.19.86
Refreshed all patches.
Altered patches:
- 950-0064-mfd-Add-Raspberry-Pi-Sense-HAT-core-driver.patch
- 0005-mtd-physmap_of-Move-custom-initialization.patch
Remove upstreamed:
- 0001-pinctrl-gemini-Mask-and-set-properly.patch
- 0002-pinctrl-gemini-Fix-up-TVC-clock-group.patch
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 25 Nov 2019 10:29:17 +0000 (11:29 +0100)]
kernel: bump 4.14 to 4.14.156
Refreshed all patches.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Daniel Golle [Thu, 28 Nov 2019 19:17:20 +0000 (11:17 -0800)]
ucert: update to latest git HEAD
e4bd927 cast ucert_argv to proper type when passing to execv
Fixes warnings:
warning: passing argument 2 of 'execv' from incompatible pointer type
[-Wincompatible-pointer-types]
254 | execv(usign_argv[0], usign_argv)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Stijn Tintel [Thu, 28 Nov 2019 00:01:05 +0000 (02:01 +0200)]
config: kernel: fix typo in HFSPLUG_FS_POSIX_ACL
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Adrian Schmutzler [Sat, 23 Nov 2019 17:20:34 +0000 (18:20 +0100)]
mpc85xx: add vendor to Makefile node name, derive SUPPORTED_DEVICES
By adding the vendor to the Makefile device definition node name,
one can derive the standard compatible used in SUPPORTED_DEVICES
instead of having to specify it manually.
Despite, this moves the naming scheme closer to what is used for
other targets (ath79, ramips).
Build-tested on all subtargets.
Run-tested on TP-Link TL-WDR4900 v1.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 27 Nov 2019 20:05:29 +0000 (21:05 +0100)]
tools: tplink-safeloader: fix whitespace issues
This replaces tabs by spaces when preceding an equal sign. This improves
consistency in the file and makes the indent look correct on all platforms.
While at it, also fix one case of inconsistent leading spaces.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Anderson Vulczak [Sat, 5 Oct 2019 13:44:55 +0000 (10:44 -0300)]
ath79: add support for TP-Link Archer C6 v2 (US) and A6 (US/TW)
This patch is based on #1689 and adds support for TP-Link Archer
C6 v2 (US) and A6 (US/TW).
The hardware is the same as EU and RU variant, except for GPIOs
(LEDS/Buttons), flash(chip/partitions) and UART being available
on the board.
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q127CS1G (16MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) QCA9563 integrated (3x3)
- 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: 115200, 8n1 (header available on board)
Known issues:
- Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range.
Flash instructions:
Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin
via the router Web interface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
tftp root directory renamed to ArcherA6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the
reset button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing
Flash partitioning: I've followed #1689 for defining the partition layout
for this patch. The partition named as "tplink" @ 0xfd0000 is marked
as read only as it is where some config for stock firmware are stored.
On stock firmware those stock partitions starts at 0xfd9400 however
I had not been able to make it functional starting on the same address as
on stock fw, so it has been partitioned following #1689 and not the stock
partition layout for this specific partition. Due to that firmware/rootfs
partition lenght is 0xf80000 and not 0xf89400 as stock.
According to the GPL code, the EU/RU/JP variant does have different GPIO pins
assignment to LEDs and buttons, also the flash memory layout is different.
GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz
Signed-off-by: Anderson Vulczak <andi@andi.com.br>
[wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases
to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Fri, 22 Nov 2019 13:42:47 +0000 (14:42 +0100)]
ath79: rename EEPROM to art
This renames all remaining occurrences of "EEPROM" to "art" to
further harmonize the partition labelling in ath79. This will
help to reduce the amount of user-space code and might be
beneficial when code is copy/pasted in the future.
Affected are only devices from Ubiquiti, where the XM board is
already using "art" in ath79.
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Jason A. Donenfeld [Wed, 27 Nov 2019 14:50:49 +0000 (15:50 +0100)]
wireguard: bump to 0.0.
20191127
* messages: recalculate rekey max based on a one minute flood
* allowedips: safely dereference rcu roots
* socket: remove redundant check of new4
* allowedips: avoid double lock in selftest error case
* tools: add syncconf command
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Hans Dedecker [Tue, 26 Nov 2019 20:53:21 +0000 (21:53 +0100)]
procd: update to latest git HEAD
3aa051b system: sysupgrade: close input side of pipe before reading
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Piotr Dymacz [Wed, 13 Nov 2019 13:51:31 +0000 (14:51 +0100)]
uboot-envtools: ath79: add support for YunCore XD4200 and A782
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Piotr Dymacz [Tue, 12 Nov 2019 21:36:28 +0000 (22:36 +0100)]
ath79: add support for YunCore XD4200 and A782
YunCore XD4200 ('XD4200_W6.0' marking on PCB) is Qualcomm/Atheros based
(QCA9563, QCA9886, QCA8334) dual-band, Wave-2 AC1200 ceiling AP with PoE
(802.3at) support. A782 model ('T750_V5.1' marking on PCB) is a smaller
version of the XD4200, with similar specification but lower TX power.
Specification:
- QCA9563 (775 MHz)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet (QCA8334), with 802.3at PoE support (WAN)
- Wi-Fi 2.4 GHz:
- XD4200: 2T2R (QCA9563), with ext. PA (SKY65174-21) and LNA
- A782: 2T2R (QCA9563), with ext. FEM (SKY85329-11)
- Wi-Fi 5 GHz:
- XD4200: 2T2R (QCA9886), with ext. FEM (SKY85728-11)
- A782: 2T2R (QCA9886), with ext. FEM (SKY85735-11)
- LEDs:
- XD4200: 5x (2x driven by SOC, 1x driven by AC radio, 2x Ethernet)
- A782: 3x (1x RGB, driven by SOC and radio, 2x Ethernet)
- 1x button (reset)
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x DC jack (12 V)
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Vincent Wiemann [Mon, 12 Aug 2019 23:26:45 +0000 (01:26 +0200)]
ath79: add support for YunCore TFTP image generation
YunCore QCA9k based devices released in 2019 require a custom TFTP image
for U-Boot built-in recovery mode (triggered with reset button). Image
has to be prepended with 'YUNCORE' keyword followed by U-Boot CLI
commands which will be executed later. Images without the custom header
will be ignored by U-Boot.
To be able to support both the vendor firmware (QSDK) and OpenWrt flash
layouts, used here commands change the 'bootcmd' before flashing image.
This commit adds generic helper script for YunCore devices with 16 MB of
flash and enables TFTP image generation for A770 model.
Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
[pepe2k@gmail.com: commit description reworded, recipe renamed]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Piotr Dymacz [Sun, 10 Nov 2019 23:33:58 +0000 (00:33 +0100)]
ath79: generic: base-files: fix indentation in 02_network
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
David Bauer [Sat, 23 Nov 2019 18:28:47 +0000 (19:28 +0100)]
tools/expat: change package source to GitHub
According to the SourceForge page, the project is migrating to GitHub.
Thus, change the source of the package to GitHub.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sun, 17 Nov 2019 14:51:48 +0000 (15:51 +0100)]
ramips: reorganize NETGEAR sercomm boards
This re-organizes the device-tree files for the Sercomm-manufactured
NETGEAR routers. They are now split into two different base-boards,
from which the respective model is extended.
This partially reverts commit
c7842ceaaa27 ("ramips: reorganize DTSI
files for Netgear R devices"), which introduced inheritance between two
completely unrelated base-boards.
Signed-off-by: David Bauer <mail@david-bauer.net>
DENG Qingfang [Sun, 24 Nov 2019 12:27:53 +0000 (20:27 +0800)]
ccache: update to 3.7.6
Update ccache to 3.7.6
Release notes:
https://ccache.dev/releasenotes.html#_ccache_3_7_6
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Hannu Nyman [Sat, 9 Nov 2019 20:22:15 +0000 (22:22 +0200)]
tools/quilt: update to 0.66
Update quilt to version 0.66
Release notes at:
http://git.savannah.nongnu.org/cgit/quilt.git/tree/NEWS?id=
294006e12
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Petr Štetiar [Sun, 24 Nov 2019 12:51:42 +0000 (13:51 +0100)]
libubox: update to latest Git HEAD
07413cce72e1 tests: jshn: add more test cases
26586dae43a8 jshn: fix missing usage for -p and -o arguments
8e832a771d3a jshn: fix off by one in jshn_parse_file
cb698e35409b jshn: jshn_parse: fix leaks of memory pointed to by 'obj'
c42f11cc7c0f jshn: main: fix leak of memory pointed to by 'vars'
93848ec96dc5 jshn: refactor main into smaller pieces
9b6ede0e5312 avl: guard against theoretical null pointer dereference
c008294a8323 blobmsg_json: fix possible uninitialized struct member
0003ea9c45cc base64: fix possible null pointer dereference
8baeeea1f52d add assert.h component
b0a5cd8a28bf add cram based unit tests
1fefb7c4d7f9 add initial GitLab CI support
c955464d7a9b enable extra compiler checks
6228df9de91d iron out all extra compiler warnings
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Stijn Segers [Fri, 22 Nov 2019 18:38:46 +0000 (19:38 +0100)]
ath79: remove ath10k drivers from Archer C7 v1 profile
Ath10k packages were removed from ar71xx in master in commit
34113999ef43 ("ar71xx: Remove ath10k packages from archer-c7-v1 (fixes
FS#1743)") but ath79 in master and the 19.07 branch still suffer from
the issue.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 18 Nov 2019 14:40:08 +0000 (15:40 +0100)]
treewide: kernel config: remove runtime options
Remove CC_HAS_ASM_GOTO, CC_IS_GCC and GCC_VERSION kernel config options
which are set at runtime and which should be ignored now.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 18 Nov 2019 13:32:23 +0000 (14:32 +0100)]
kernel-build: ignore runtime config options during reconfig
Don't put CC_HAS_ASM_GOTO, IS_GCC, IS_CLANG and GCC_VERSION runtime
config options into the kernel configs during reconfiguration as it
makes no sense, since these options should be set at runtime.
Fixes: FS#2588
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hans Dedecker [Sat, 23 Nov 2019 20:25:13 +0000 (21:25 +0100)]
nghttp2: bump to 1.40.0
41060943 Bump up version number to 1.40.0, LT revision to 33:0:19
5ae9bb89 Fail fast if huffman decoding context is in failure state
bb519154 Merge pull request #1413 from nghttp2/check-authority
77f5487a Add nghttp2_check_authority as public API
db9a8f6e Merge pull request #1409 from nghttp2/fix-wrong-stream-close-error-code
6f28a69b Merge pull request #1411 from richard78917/fix_warning
6ce4835e Fix the bug that stream is closed with wrong error code
29042f1c priority_spec::valid(): remove const qualifier from return value
d08c4395 Merge pull request #1405 from nghttp2/huffman
5d6964cf Faster huffman decoding
0d855bfc Faster huffman encoding
6f967c6e Fix errors reported by coverity scan
b8a43db8 Merge pull request #1394 from wrowe/fix-static-libname
70b62c1a Merge pull request #1393 from wrowe/fix-static-msvcrt
28b1f0b9 Avoid filename collision of static and dynamic lib
1dd966f1 Merge branch 'fix-nghttpx-mruby'
fe8946dd nghttpx: Fix bug that mruby is incorrectly shared between backends
72b71a6b Add new flag ENABLE_STATIC_CRT for Windows
f8933fe5 nghttpx: Reconnect h1 backend if it lost connection before sending headers
89c33d69 Update neverbleed
7079dc5e Update neverbleed to fix memory leak
5080db84 Revert "nghttpx: Reconnect h1 backend if it lost connection before sending headers"
053c7ac5 nghttpx: Returns 408 if backend timed out before sending headers
8a59ce6d nghttpx: Reconnect h1 backend if it lost connection before sending headers
f2fde180 Remove redundant null check before delete
95efb3e1 Don't read too greedily
0a6ce87c Add nghttp2_option_set_max_outbound_ack
2aa79fa9 Bump up LT revision to 32:0:18
3980678d Merge branch 'nghttpx-fix-request-stall'
319d5ab1 nghttpx: Fix request stall
448bbbc3 integration-tests: gofmt
e575a2aa Merge pull request #1377 from Aldrog/cmake_systemd
4f7aedc9 cmake: Support building nghttpx with systemd
7a590893 Fix clang-8 warning
ee443134 Fix FPE with default backend
abef9b90 Fix log-level is not set with cmd-line or configuration file
12a999f0 Bump up version number to 1.40.0-DEV
acfb3607 Update manual pages
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Yousong Zhou [Sat, 23 Nov 2019 18:05:45 +0000 (18:05 +0000)]
kernel: nf_conntrack_rtcache: fix WARNING on rmmod
Fixes
b7c58a1ee ("kernel: nf_conntrack_rtcache: fix cleanup on netns
delete and rmmod")
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Yousong Zhou [Sat, 23 Nov 2019 17:10:09 +0000 (17:10 +0000)]
kernel: nf_conntrack_rtcache: fix WARNING on forward path
Fixes
b7c58a1ee ("kernel: nf_conntrack_rtcache: fix cleanup on netns
delete and rmmod")
Resolves FS#2624
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Kamil Wcislo [Thu, 5 Jul 2018 19:40:19 +0000 (21:40 +0200)]
build: add PKG_SOURCE_URL_FILE support
It seems that there is a missing PKG_SOURCE_URL_FILE support.
This little fix adds the support for packages to change the name of the
downloaded file.
Sometimes it is desirable to change the downloaded archive file name, like
for mitigating name conflicts for different packages (some files on the server
could be named like, e.g. 2018-01-01.tar.gz) or for the cases that there is
no name for the file in the URL (e.g. http://someserver.com/download).
Signed-off-by: Kamil Wcislo <kamil.wcislo@lpnplant.io>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Adrian Schmutzler [Fri, 22 Nov 2019 10:50:00 +0000 (11:50 +0100)]
ath79: improve TP-Link CPE DTSI names for ar9344 SOC
The initial DTSI names for the TP-Link CPE devices have become
quite confusing, as several non-V1 devices now use the *-v1.dtsi,
the *cpe510-v1.dts does not use the cpe510.dtsi, etc.
This introduces a new naming scheme based on whether devices have
one or two ports, which should be easier to grasp.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Bernhard Geier [Fri, 22 Nov 2019 22:11:24 +0000 (23:11 +0100)]
tplink-safeloader: shorten version number of TP-Link WBS210 v2
"2.0" instead of "2.00" is sufficient and more in line with the
other definitions.
Signed-off-by: Bernhard Geier <freifunk@geierb.de>
[commit message/title adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Mon, 11 Nov 2019 16:20:45 +0000 (01:20 +0900)]
base-files: config_generate: split macaddr with multiple ifaces
netifd does not handle network.@device[x].name properly if it
contains multiple ifaces separated by spaces. Due to this, board.d
lan_mac setup does not work if multiple ifaces are set to LAN by
ucidef_set_interface_lan.
To fix this, create a device node for each member iface when
running config_generate instead. Those are named based on the
member ifname:
ucidef_set_interface_lan "eth0 eth1.1"
ucidef_set_interface_macaddr "lan" "yy:yy:yy:yy:yy:01"
will return
config device 'lan_eth0_dev'
option name 'eth0'
option macaddr 'yy:yy:yy:yy:yy:01'
config device 'lan_eth1_1_dev'
option name 'eth1.1'
option macaddr 'yy:yy:yy:yy:yy:01'
ref: https://github.com/openwrt/openwrt/pull/2542
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[always use new scheme, extend description, change commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Tue, 19 Nov 2019 14:47:11 +0000 (15:47 +0100)]
ath79: DTS style improvement for Ubiquiti XM and BZ devices
This applies minor style improvements and removes commented pll
clock adjustments from ubnt_xm DTSI. The latter were introduced
(already commented out) when adding ath79 target and have never
been touched since then. For Unifi (BZ board), similar clock
adjustments are employed and used.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>