oweals/u-boot.git
4 years agoarm64: zynqmp: Enable netconsole for ZynqMP
Michal Simek [Wed, 18 Mar 2020 08:19:02 +0000 (09:19 +0100)]
arm64: zynqmp: Enable netconsole for ZynqMP

It is nice feature

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: zynqmp Add support for zcu111 revA
Michal Simek [Mon, 16 Mar 2020 11:40:16 +0000 (12:40 +0100)]
arm64: zynqmp Add support for zcu111 revA

Add low level configuration for zcu111 for easier SPL run.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agonet: eth-uclass: Fix message if mac is coming from DT or ROM
Michal Simek [Mon, 16 Mar 2020 10:36:17 +0000 (11:36 +0100)]
net: eth-uclass: Fix message if mac is coming from DT or ROM

When local-mac-address DT property is specified it is reported the same way
as address read from eeprom/ROM. Show properly if mac address is coming
from DT or ROM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoARM: zynq: Enable i2c mux support for all boards
Michal Simek [Thu, 5 Mar 2020 07:17:49 +0000 (08:17 +0100)]
ARM: zynq: Enable i2c mux support for all boards

zc702/zc706 have pca9548 i2c muxes that's why enable the driver by default.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: zynqmp Add support for zcu102 rev1.1
Michal Simek [Thu, 12 Mar 2020 08:03:13 +0000 (09:03 +0100)]
arm64: zynqmp Add support for zcu102 rev1.1

rev1.1 has different DDR sodimm module that's why it requires different DDR
configuration.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: zynqmp: Add third backup bootmode
Michal Simek [Wed, 11 Mar 2020 14:00:51 +0000 (15:00 +0100)]
arm64: zynqmp: Add third backup bootmode

I found this issue when was running py/test.py on zcu102 which is for me by
default setup to SD boot mode without any way to change boot mode.
Alternative software bootmode selection to JTAG is not working because JTAG
mode is 0 which also reset value for it. That's why saying SPL to take
u-boot.itb from RAM instead of SD in SD boot mode is not possible via
alternative bootmode selection.
That's why setup third boot mode to JTAG(BOOT_DEVICE_RAM) as final
fallback.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agowatchdog: cadence: Remove DECLARE_GLOBAL_DATA_PTR from driver
Michal Simek [Mon, 9 Mar 2020 07:44:43 +0000 (08:44 +0100)]
watchdog: cadence: Remove DECLARE_GLOBAL_DATA_PTR from driver

gd is not used in the driver that's why declaration is not needed at all.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agonet: zynq-gem: Setup and use mdio base separately
Michal Simek [Mon, 30 May 2016 08:43:11 +0000 (10:43 +0200)]
net: zynq-gem: Setup and use mdio base separately

Not all IPs have private MDIO bus and MDIO bus should be shared between
several IPs. In past one patch tried to implement it
(https://lists.denx.de/pipermail/u-boot/2018-February/319285.html)
in pretty raw way but it is not the cleanest solution.
This patch is just taking the part of that solution to be able to handle it
over releases without conflicts.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoARM: zynq: Do not print message about boot device
Michal Simek [Thu, 5 Mar 2020 10:01:50 +0000 (11:01 +0100)]
ARM: zynq: Do not print message about boot device

This information is shown already that's why there is no reason to print it
again via custom prints.

U-Boot SPL 2020.01-03080-ga6214d033bd0 (Mar 05 2020 - 09:59:05 +0100)
mmc boot
Trying to boot from MMC1

or

U-Boot SPL 2020.01-03080-ga6214d033bd0 (Mar 05 2020 - 10:49:46 +0100)
qspi boot
Trying to boot from SPI

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: zynqmp: Check firmware node when driver is enabled
Michal Simek [Wed, 4 Mar 2020 07:48:16 +0000 (08:48 +0100)]
arm64: zynqmp: Check firmware node when driver is enabled

ZynqMP mini configurations works without PMU firmware that's why there is
no reason to enable the driver and check if it was probed properly.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: versal: Enable support for Gigadevice/ISSI flashes
T Karthik Reddy [Mon, 17 Feb 2020 11:49:40 +0000 (04:49 -0700)]
arm64: versal: Enable support for Gigadevice/ISSI flashes

Enable support for Gigadevice/ISSI flash parts for Versal platform.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoenv: Make mmc as default option for CONFIG_ENV_FAT_INTERFACE
Michal Simek [Tue, 25 Feb 2020 14:50:33 +0000 (15:50 +0100)]
env: Make mmc as default option for CONFIG_ENV_FAT_INTERFACE

All configs are using mmc as default fat interface. That's why make it
default for everybody.
The reason for this patch is to make it default for Xilinx Zynq platform
which is not listed there.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoARM: zynq: Enable DM for CFI NOR flash
Michal Simek [Tue, 25 Feb 2020 14:29:40 +0000 (15:29 +0100)]
ARM: zynq: Enable DM for CFI NOR flash

With multi defconfig NOR flash information about NOR should be taken from
DT that's why there is no reason to specify address and sizes via fixed
config.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoARM: zynq: Do not report NOR flash detection failure
Michal Simek [Tue, 25 Feb 2020 13:55:58 +0000 (14:55 +0100)]
ARM: zynq: Do not report NOR flash detection failure

With multi defconfig targeting several board configurations bug report like
below is so verbose.
Flash: ## Unknown flash on Bank 1 - Size = 0x00000000 = 0 MB
0 Bytes

Do not report that message and simply say "Flash: 0 Bytes" because most of
Zynq boards are using different type of flashes than NOR.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agonand: raw: zynq: Do not try to probe driver if nand flash is disabled
Michal Simek [Tue, 25 Feb 2020 13:40:42 +0000 (14:40 +0100)]
nand: raw: zynq: Do not try to probe driver if nand flash is disabled

There is no reason to continue when DT status property indicates that NAND
flash is disabled. But that means that NOR flash should be present that's
why try it find it out.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
4 years agonand: raw: Do not free xnand structure
Michal Simek [Tue, 25 Feb 2020 13:51:48 +0000 (14:51 +0100)]
nand: raw: Do not free xnand structure

xnand structure is private data structure and it is handled by core and
probe shouldn't touch it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
4 years agoARM: zynq: Do not include full zynq-7000.dtsi to cse-nor configuration
Michal Simek [Wed, 26 Feb 2020 10:11:38 +0000 (11:11 +0100)]
ARM: zynq: Do not include full zynq-7000.dtsi to cse-nor configuration

There is no real need to include full DT when only some nodes are enough to
use. It will save some space.

Retested with FSBL for initial SoC setup. SPL didn't work.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agonet: zynq_gem: Add cache flush to zynq_gem_free_pkt
Ashok Reddy Soma [Sun, 23 Feb 2020 15:01:29 +0000 (08:01 -0700)]
net: zynq_gem: Add cache flush to zynq_gem_free_pkt

Add cache flush to zynq_gem_free_pkt. This is necessary
because some net routines would modify this buffer in place.
The cache_invalidate in the zynq_gem_recv function would cause
the modifications to the buffer to overwrite the DMA from the GEM,
if cache coherency is not enabled in the GEM, the next time the
buffer is in use.

Flushing the cache when the buffer is no longer in use by the
net functions ensures that the GEM DMA is going to take place
into a clean buffer.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoARM: zynq: Switch to single zynq configurations
Michal Simek [Thu, 13 Feb 2020 14:03:29 +0000 (15:03 +0100)]
ARM: zynq: Switch to single zynq configurations

There are a lot of zynq configurations which can be merged together and use
only one for all. The similar change has been done for ZynqMP by commit
be1b6c32d940 ("arm64: zynqmp: Use zynqmp_virt platform")

Build SPL with u-boot.img for zc706 like this.
export DEVICE_TREE=zynq-zc706 && make xilinx_zynq_virt_defconfig && make -j8
u-boot.img is generic for all boards.

Tested on Zybo, zc702, zc706, zc770-xm011-x16, cc108 and microzed.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoMakefile: Add environment variable DEVICE_TREE to header
Michal Simek [Tue, 18 Feb 2020 14:03:13 +0000 (15:03 +0100)]
Makefile: Add environment variable DEVICE_TREE to header

Users have option to overwrite default device tree
(CONFIG_DEFAULT_DEVICE_TREE) via environment variable DEVICE_TREE.

Feature has been added long time ago by commit 74de8c9a1672
("dts/Makefile: Build the user specified dts") for a little bit different
reason.

But this variable can be also used for different purpose like choosing
proper configuration from FIT image in SPL.
And this is the functionality I would like to use on Xilinx Zynq devices
that current u-boot.img can be composed in the same way based on OF_LIST
and different configuration is taken based on platform specific SPL.
SPL requires low level ps7_init_gpl configuration that's why different
boards require different SPL with fixed board_fit_config_name_match().

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
4 years agoARM: zynq: Change zc770 xm011 Nand x16 configurations
Michal Simek [Tue, 18 Feb 2020 14:58:33 +0000 (15:58 +0100)]
ARM: zynq: Change zc770 xm011 Nand x16 configurations

Instead of symlink include origin file and just change model description.
Difference is not in DT but in ps7_init configurations which is taken based
on device tree name that's why the same DT can't be used.

Also update model and update comments to match configurations.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoenv: Kconfig: Adding default values for Microblaze
Varalaxmi Bingi [Wed, 5 Feb 2020 10:58:20 +0000 (03:58 -0700)]
env: Kconfig: Adding default values for Microblaze

This patch will add default values for ENV_OFFSET
and ENV_SECT_SIZE for Microblaze.

Signed-off-by: Varalaxmi Bingi <varalaxmi.bingi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: zynqmp: Move pinctrl node under firmware node
Michal Simek [Tue, 18 Feb 2020 12:04:06 +0000 (13:04 +0100)]
arm64: zynqmp: Move pinctrl node under firmware node

Pinctrl is handled via firmare interface that's why move it there without
reg property and new compatible string.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: zynqmp: Fix GIC compatible property
Michal Simek [Tue, 18 Feb 2020 09:01:26 +0000 (10:01 +0100)]
arm64: zynqmp: Fix GIC compatible property

dtbs_check is showing warning around GIC compatible property as
interrupt-controller@f9010000: compatible: ['arm,gic-400', 'arm,cortex-a15-gic']
is not valid under any of the given schemas

Similar change has been done also by Linux kernel commit 5400cdc1410b
("ARM: dts: sunxi: Fix GIC compatible")

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoARM: zynq: Fix addresses in partition definitions
Michal Simek [Wed, 19 Feb 2020 09:57:34 +0000 (10:57 +0100)]
ARM: zynq: Fix addresses in partition definitions

Node name should be <name>@<address> which is not how partitions are
described.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: zynqmp: Fix addresses in partition definitions
Michal Simek [Fri, 14 Feb 2020 13:19:56 +0000 (14:19 +0100)]
arm64: zynqmp: Fix addresses in partition definitions

Node name should be <name>@<address> which is not how partitions are
described.

Issue was found by running dtbs_check as:
flash@0: 'partition@qspi-device-tree', 'partition@qspi-fsbl-uboot',
'partition@qspi-linux', 'partition@qspi-rootfs'
do not match any of the regexes: ...

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: zynqmp: Sync DP subsystem
Michal Simek [Tue, 18 Feb 2020 08:24:08 +0000 (09:24 +0100)]
arm64: zynqmp: Sync DP subsystem

Sync DP subsystem with the latest state in Xilinx U-Boot repository.
This binding hasn't been approved in mainline Linux but it is much better
than ancient version which this patch removes.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: zynqmp: Do not duplicate flash partition label property
Amit Kumar Mahapatra [Mon, 17 Feb 2020 14:50:05 +0000 (07:50 -0700)]
arm64: zynqmp: Do not duplicate flash partition label property

In kernel 5.4, support has been added for reading MTD devices via
the nvmem API.
For this the mtd devices are registered as read-only NVMEM providers
under sysfs with the same name as the flash partition label property.

So if flash partition label property of multiple flash devices are identical
then the second mtd device fails to get registered as a NVMEM provider.

This patch fixes the issue by having different label property for different
flashes.

Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: dts: zynqmp: Add clk cells for sdhci
Ashok Reddy Soma [Tue, 18 Feb 2020 06:32:57 +0000 (23:32 -0700)]
arm64: dts: zynqmp: Add clk cells for sdhci

Add clock-cells and clock-output-names for sdhci0 and sdhci1.
These are needed for linux sdhci driver from 5.4 version onwards.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: zynqmp: Remove second copy of reset-controller
Michal Simek [Tue, 18 Feb 2020 08:20:21 +0000 (09:20 +0100)]
arm64: zynqmp: Remove second copy of reset-controller

Reset controller is handled via firmware that's why it should be the part
of firmware node. Origin solution hasn't been removed when above change was
applied by commit b07e97b4ba27 ("arm64: zynqmp: Use reset header in
zynqmp.dtsi").

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: zynqmp: Add 'no-1-8-v' property for ZynqMP Boards
Manish Narani [Fri, 14 Feb 2020 06:37:30 +0000 (23:37 -0700)]
arm64: zynqmp: Add 'no-1-8-v' property for ZynqMP Boards

Modify dts files to add 'no-1-8-v' property for all the ZynqMP boards.
User can remove this property to enable the UHS mode. This is to keep
the same speed (HS) modes across all the stages of the Linux Boot. Due
to power cycling limitation of some of the ZynqMP boards, some SD cards
don't get power cycled and are failing in Linux.

Signed-off-by: Manish Narani <manish.narani@xilinx.com>
4 years agoarm64: zynqmp: Sync zynqmp fpga manager with mainline
Nava kishore Manne [Fri, 18 Oct 2019 16:07:32 +0000 (18:07 +0200)]
arm64: zynqmp: Sync zynqmp fpga manager with mainline

Sync zynqmp fpga manager with mainline.

Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: zynqmp: Remove unused zynqmp-clk.dtsi
Michal Simek [Tue, 18 Feb 2020 08:10:18 +0000 (09:10 +0100)]
arm64: zynqmp: Remove unused zynqmp-clk.dtsi

All boards have been converted to firmware based driver that's why we can
remove this file now.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoARM: zynq: Fix spi name node
Michal Simek [Thu, 26 Sep 2019 10:53:09 +0000 (12:53 +0200)]
ARM: zynq: Fix spi name node

None name address should be aligned with address. DTC 1.5.1 is reporting
issues related to that.

arch/arm/boot/dts/zynq-zc770-xm010.dts:106.10-119.4: Warning
 (spi_bus_reg): /amba/spi@e0007000/flash@0: SPI bus unit address format
 error, expected "1"
arch/arm/boot/dts/zynq-zc770-xm013.dts:101.19-109.4: Warning
(spi_bus_reg): /amba/spi@e0006000/eeprom@0: SPI bus unit address format
 error, expected "2"

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: zynqmp: Update Copyright years to 2020
Michal Simek [Tue, 18 Feb 2020 07:38:06 +0000 (08:38 +0100)]
arm64: zynqmp: Update Copyright years to 2020

Trivial change.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: zynqmp: Replace gpio-key,wakeup with wakeup source
Michal Simek [Tue, 18 Feb 2020 11:06:14 +0000 (12:06 +0100)]
arm64: zynqmp: Replace gpio-key,wakeup with wakeup source

The same change has been done for Zynq by commit 1241c72b6db1
("ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source property")
in mainline Linux kernel.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoARM: dts: zynq: replace gpio-key,wakeup with wakeup-source property
Sudeep Holla [Fri, 21 Dec 2018 18:12:13 +0000 (18:12 +0000)]
ARM: dts: zynq: replace gpio-key,wakeup with wakeup-source property

Most of the legacy "gpio-key,wakeup" boolean property is already
replaced with "wakeup-source". However few occurrences of old property
has popped up again, probably from the remnants in downstream trees.

Replace the legacy properties with the unified "wakeup-source"
property introduced in the Linux kernel commit 700a38b27eef
("Input: gpio_keys - switch to using generic device properties")

Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoARM: dts: zc702: Fix I2C bus warnings
Quanyang Wang [Mon, 23 Sep 2019 09:47:08 +0000 (17:47 +0800)]
ARM: dts: zc702: Fix I2C bus warnings

The dtc has new checks for I2C and SPI buses.
Fix the warnings in node names and unit-addresses.

Warning from Linux kernel:
arch/arm/boot/dts/zynq-zc702.dts:187.13-190.6: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@52: I2C bus unit address format error, expected "34"
arch/arm/boot/dts/zynq-zc702.dts:191.13-194.6: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@53: I2C bus unit address format error, expected "35"
arch/arm/boot/dts/zynq-zc702.dts:195.13-198.6: Warning (i2c_bus_reg): /amba/i2c@e0004000/i2c-mux@74/i2c@7/hwmon@54: I2C bus unit address format error, expected "36"

Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: zynqmp: Enable cache command for mini mtest configuration
Michal Simek [Mon, 17 Feb 2020 11:14:32 +0000 (12:14 +0100)]
arm64: zynqmp: Enable cache command for mini mtest configuration

Enable cache commands by default for mtest configuration. It is good to be
able to enable/disable caches when you test memory.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoconfigs: versal: Add CONFIG_DISTRO_DEFAULTS to versal defconfig
T Karthik Reddy [Fri, 14 Feb 2020 05:26:56 +0000 (22:26 -0700)]
configs: versal: Add CONFIG_DISTRO_DEFAULTS to versal defconfig

Add DISTRO_DEFAULTS config to versal virt defconfig file which is
suitable for booting general purpose Linux distributions. Remove
other configs which are selected by default by DISTRO_DEFAULTS
configuration.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoarm64: zynqmp: Print multiboot register value in EL3
Michal Simek [Tue, 11 Feb 2020 11:43:14 +0000 (12:43 +0100)]
arm64: zynqmp: Print multiboot register value in EL3

Multi boot register can be used for using different boot images and design
better boot strategy. Let EL3 SPL or U-Boot to read it and print it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
4 years agoMerge branch 'master' of git://git.denx.de/u-boot-sh
Tom Rini [Sat, 4 Apr 2020 23:20:45 +0000 (19:20 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-sh

- net: sh_eth: Init the hardware before PHY access

4 years agoMerge https://gitlab.denx.de/u-boot/custodians/u-boot-x86
Tom Rini [Sat, 4 Apr 2020 23:20:26 +0000 (19:20 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86

- verdin-imx8mm board reST documentation update
- Intel Edison board ACPI table I2C/USB minor updates
- Fix a regression of ns16550 serial driver that breaks Intel Edison

4 years agoserial: ns16550: Fix ordering of getting base address
Bin Meng [Sat, 4 Apr 2020 01:35:32 +0000 (18:35 -0700)]
serial: ns16550: Fix ordering of getting base address

Currently the driver gets ns16550 base address in the driver
probe() routine, which may potentially break any ns16550 wrapper
driver that does additional initialization before calling
ns16550_serial_probe().

Things are complicated that we need consider ns16550 devices on
both simple-bus and PCI bus. To fix the issue we move the base
address assignment for simple-bus ns16550 device back to the
ofdata_to_platdata(), and assign base address for PCI ns16550
device in ns16550_serial_probe().

This is still not perfect. If any PCI bus based ns16550 wrapper
driver tries to access plat->base before calling probe(), it is
still subject to break.

Fixes: 720f9e1fdb0c9 ("serial: ns16550: Move PCI access from ofdata_to_platdata() to probe()")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Tested-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
4 years agox86: acpi: Describe USB 3 host controller found on Intel Tangier
Andy Shevchenko [Thu, 26 Mar 2020 10:33:36 +0000 (12:33 +0200)]
x86: acpi: Describe USB 3 host controller found on Intel Tangier

USB 3 host controller may be described in ACPI to allow users alter
the properties or other features. Describe it for Intel Tangier SoC.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
4 years agox86: acpi: Add I²C timings to Intel Merrifield platform
Andy Shevchenko [Fri, 20 Mar 2020 17:59:21 +0000 (19:59 +0200)]
x86: acpi: Add I²C timings to Intel Merrifield platform

There is established way to provide I²C timings, or actually counters,
to the OS via ACPI. Fill them for Intel Merrifield platform.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
4 years agodoc: board: verdin-imx8mm: use mainline TF-A
Igor Opaniuk [Thu, 5 Mar 2020 20:56:26 +0000 (22:56 +0200)]
doc: board: verdin-imx8mm: use mainline TF-A

1. Update build steps where mainline Trusted Firmware A is used.
2. Fix BL31_BASE to the proper one according to the SoC reference
manual.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
4 years agox86: acpi: Refactor XSDT handling in acpi_add_table()
Andy Shevchenko [Thu, 27 Feb 2020 14:00:51 +0000 (16:00 +0200)]
x86: acpi: Refactor XSDT handling in acpi_add_table()

There is no need to have an assignment to NULL for XSDT pointer.
Therefore, no need to assign it when rsdt_address is not set.
Because of above changes we may decrease indentation level as well.

While here, drop unnecessary parentheses.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
4 years agonet: sh_eth: Init the hardware before PHY access
Marek Vasut [Sat, 4 Apr 2020 13:01:22 +0000 (15:01 +0200)]
net: sh_eth: Init the hardware before PHY access

To access the PHY, the MAC registers must be initialized. Call the init
function in probe() to make it so, otherwise the PHY ID readout returns
all zeroes.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
4 years agoMerge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-tegra
Tom Rini [Fri, 3 Apr 2020 20:05:46 +0000 (16:05 -0400)]
Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-tegra

- Add support for Jetson Nano, plus miscellaneous other fixes found
  during Nano bringup.
- Add Igor's update_uboot wrapper patches.

4 years agoarch: Add explicit linker script for u-boot-elf
Michal Simek [Mon, 30 Mar 2020 11:58:59 +0000 (13:58 +0200)]
arch: Add explicit linker script for u-boot-elf

Commit f4dc714aaa2d ("arm64: Turn u-boot.bin back into an ELF file after
relocate-rela")
introduce REMAKE_ELF option to recreate u-boot.elf from u-boot ->
u-boot.bin + DT -> u-boot.elf.

The best is to ilustrate it from make V=1 output
  cat u-boot-nodtb.bin dts/dt.dtb > u-boot-dtb.bin
  cp u-boot-dtb.bin u-boot.bin
aarch64-linux-gnu-objcopy -I binary -B aarch64 -O elf64-littleaarch64  u-boot.bin u-boot-elf.o
  aarch64-linux-gnu-ld.bfd u-boot-elf.o -o u-boot.elf --defsym="_start"=0x8000000 -Ttext=0x8000000

Last command has no explicit linker script passed that's why toolchain
internal linker script is used.
In Binutils 2.32 case it contains SIZEOF_HEADERS symbol which has changed
behavior by commit
https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=64029e93683a266c38d19789e780f3748bd6a188
which result in situation that program headers has changed from
(xilinx_zynqmp_mini_defconfig)

Program Headers:
  Type           Offset             VirtAddr           PhysAddr
                 FileSiz            MemSiz              Flags  Align
  LOAD           0x0000000000010000 0x00000000fffc0000 0x00000000fffc0000
                 0x0000000000018918 0x0000000000018918  RW     0x10000

to

Program Headers:
  Type           Offset             VirtAddr           PhysAddr
                 FileSiz            MemSiz              Flags  Align
  LOAD           0x0000000000000000 0x00000000fffb0000 0x00000000fffb0000
                 0x0000000000028918 0x0000000000028918  RW     0x10000

Xilinx tools like XSDB or Bootgen are using program headers for loading ELF
to the right location and by above binutils change ELF is loaded to
incorrect location.

The patch is explicitly use u-boot-elf.lds (just cat now) for u-boot.elf
recreation which is called when REMAKE_ELF is setup.
By purpose u-boot-elf.lds doesn't contain OUTPUT_FORMAT/OUTPUT_ARCH to be
able to use by all archs.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-By: Álvaro Fernández Rojas <noltari@gmail.com>
4 years agomach-snapdragon: Fix overwriting last digit of serial number
Jan-Christoph Tebbe [Mon, 16 Mar 2020 16:51:51 +0000 (17:51 +0100)]
mach-snapdragon: Fix overwriting last digit of serial number

When generating the MAC address based on the boards serial number
the last digit was overwritten with the null termination. That way
boards with serial numbers close to each other would use the same
MAC address.

Signed-off-by: Jan-Christoph Tebbe <Jan-Christoph.Tebbe@ithinx.io>
4 years agoRevert "common: spl_fit: Default to IH_OS_U_BOOT if FIT_IMAGE_TINY enabled"
Ye Li [Wed, 1 Apr 2020 14:42:04 +0000 (07:42 -0700)]
Revert "common: spl_fit: Default to IH_OS_U_BOOT if FIT_IMAGE_TINY enabled"

Commit cf8dcc5d02c3 ("common: spl_fit: Default to IH_OS_U_BOOT if
FIT_IMAGE_TINY enabled") is not correct, it will append fdt to each loadable
image. Actually when using TINY FIT, the first loadable image is thought as
u-boot and already have fdt appended.

Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
4 years agoMerge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-spi
Tom Rini [Fri, 3 Apr 2020 15:26:13 +0000 (11:26 -0400)]
Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-spi

- fix for MMIO window size (Tudor Ambarus)

4 years agoARM: tegra: Add NVIDIA Jetson Nano Developer Kit support
Tom Warren [Fri, 28 Feb 2020 23:17:07 +0000 (16:17 -0700)]
ARM: tegra: Add NVIDIA Jetson Nano Developer Kit support

The Jetson Nano Developer Kit is a Tegra X1-based development board. It
is similar to Jetson TX1 but it is not pin compatible. It features 4GB
of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot
used for storage.

HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0
and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI
Ethernet controller provides onboard network connectivity. NVMe support
has also been added. Env save is at the end of QSPI (4MB-8K).

A 40-pin header on the board can be used to extend the capabilities and
exposed interfaces of the Jetson Nano.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
4 years agomtd: spi: Add Macronix MX25U3235F device
Tom Warren [Fri, 20 Mar 2020 21:20:09 +0000 (14:20 -0700)]
mtd: spi: Add Macronix MX25U3235F device

Add Macronix MX25U3235F flash device description.
This is a 4MiB part.

Signed-off-by: Tom Warren <twarren@nvidia.com>
4 years agot210: Adjust ramdisk_addr_r/fdt_addr_r to allow for large kernels
Tom Warren [Tue, 17 Mar 2020 00:01:43 +0000 (17:01 -0700)]
t210: Adjust ramdisk_addr_r/fdt_addr_r to allow for large kernels

The L4T kernel is 32MB+, and can overwrite the ramdisk/fdt loaded
from extlinux.conf. Adjust the load addresses to fix this for now.
Using the calculated_env addresses table from T186 U-Boot is a
better fix, but it isn't working correctly on T210 U-Boot right now,
so this will do until I can fix it.

Signed-off-by: Tom Warren <twarren@nvidia.com>
4 years agoqspi: t210: Use dev_read calls to get FDT data like base, freq
Tom Warren [Fri, 20 Mar 2020 21:33:00 +0000 (14:33 -0700)]
qspi: t210: Use dev_read calls to get FDT data like base, freq

This Tegra QSPI driver hadn't been brought up to date with how
DM drivers are fetching data from the FDT now, and was pulling
in bogus data for base, max freq, etc. Fixed ofdata_to_platdata
to work the same way it does in the tegra114 SPI driver, using
dev_read_ functions.

Signed-off-by: Tom Warren <twarren@nvidia.com>
4 years agoqspi: t210: Fix QSPI clock and tap delays
Tom Warren [Mon, 25 Nov 2019 21:43:50 +0000 (14:43 -0700)]
qspi: t210: Fix QSPI clock and tap delays

When claim_bus was setting the clock, it reset the QSPI controller,
which wipes out any tap delays set by previous bootloaders (nvtboot,
CBoot for example on Nano). Instead of doing that in claim_bus, which
gets called a lot, moved clock setting to probe(), and set tap delays
there, too. Also updated clock to 80MHz to match CBoot. Now QSPI env
save works reliably again.

Signed-off-by: Tom Warren <twarren@nvidia.com>
4 years agoqspi: t210: Fix claim_bus's use of the wrong bus/device
Tom Warren [Tue, 12 Nov 2019 20:17:37 +0000 (13:17 -0700)]
qspi: t210: Fix claim_bus's use of the wrong bus/device

claim_bus() is passed a udevice *dev, which is the bus device's parent.
In this driver, claim_bus assumed it was the bus, which caused the
'priv' info pointer to be wrong, and periph_id was incorrect. This in
turn caused the periph clock call to assign the wrong clock (PLLM
instead of PLLP0), which caused a kernel warning. I only saw the 'bad'
periph_id when enabling DEBUG due to an assert. Not sure how QSPI was
working w/this errant clock, but it was moot as QSPI wasn't active
unless you probed it, and that wasn't happening until I posted a patch
to enable env save to QSPI for Nano (coming soon).

Signed-off-by: Tom Warren <twarren@nvidia.com>
4 years agommc: t210: Fix 'bad' SD-card clock when doing 400KHz card detect
Tom Warren [Mon, 3 Jun 2019 23:06:34 +0000 (16:06 -0700)]
mmc: t210: Fix 'bad' SD-card clock when doing 400KHz card detect

According to the HW team, for some reason the normal clock select code
picks what appears to be a perfectly valid 375KHz SD card clock, based
on the CAR clock source and SDMMC1 controller register settings (CAR =
408MHz PLLP0 divided by 68 for 6MHz, then a SD Clock Control register
divisor of 16 = 375KHz). But the resulting SD card clock, as measured by
the HW team, is 700KHz, which is out-of-spec. So the WAR is to use the
values given in the TRM PLLP table to generate a 400KHz SD-clock (CAR
clock of 24.7MHz, SD Clock Control divisor of 62) only for SDMMC1 on
T210 when the requested clock is <= 400KHz. Note that as far as I can
tell, the other requests for clocks in the Tegra MMC driver result in
valid SD clocks.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
4 years agommc: t210: Add autocal and tap/trim updates for SDMMC1/3
Tom Warren [Wed, 29 May 2019 16:30:01 +0000 (09:30 -0700)]
mmc: t210: Add autocal and tap/trim updates for SDMMC1/3

As per the T210 TRM, when running at 3.3v, the SDMMC1 tap/trim and
autocal values need to be set to condition the signals correctly before
talking to the SD-card. This is the same as what's being done in CBoot,
but it gets reset when the SDMMC1 HW is soft-reset during SD driver
init, so needs to be repeated here. Also set autocal and tap/trim for
SDMMC3, although no T210 boards use it for SD-card at this time.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
4 years agotegra: Enable CONFIG_BOOTP_PREFER_SERVERIP for all Jetson boards
Tom Warren [Thu, 26 Mar 2020 22:59:14 +0000 (15:59 -0700)]
tegra: Enable CONFIG_BOOTP_PREFER_SERVERIP for all Jetson boards

This allows the user to set $serverip in the environment before
executing a DHCP request. If they do, U-Boot will use that IP rather
than using the IP in the DHCP response.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
4 years agoARM: tegra: p2771-0000: enable PIE relocation
Vishruth [Thu, 26 Mar 2020 22:20:43 +0000 (15:20 -0700)]
ARM: tegra: p2771-0000: enable PIE relocation

U-Boot is configured to build as position independent executable. Enable
relocation of RELA section required to work with different load
addresses.

Signed-off-by: Vishruth <vishruthj@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Peter Robinson <probinson@gmail.com>
4 years agoi2c: t210: Add VI_I2C clock source support
Tom Warren [Fri, 27 Mar 2020 17:24:31 +0000 (10:24 -0700)]
i2c: t210: Add VI_I2C clock source support

Fix VI_I2C clock source type. Will be needed by VI_I2C driver.
Also added use of INTERNAL_ID macro in two places, needed to keep
the id returned to 8 bits.

Signed-off-by: Tom Warren <twarren@nvidia.com>
4 years agot210: pinmux: Remove pinmux/GPIO init from T210 boards
Tom Warren [Thu, 26 Mar 2020 23:10:11 +0000 (16:10 -0700)]
t210: pinmux: Remove pinmux/GPIO init from T210 boards

T210 CBoot is now doing the full pinmux and GPIO init, based on the DTB
tables. Remove pinmux/GPIO init tables & code from all T210-based builds
below:

p2371-2180 aka TX1
p2371-0000
e2220-1170
p2571

Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
4 years agot210: do not enable PLLE and UPHY PLL HW PWRSEQ
JC Kuo [Thu, 26 Mar 2020 23:10:09 +0000 (16:10 -0700)]
t210: do not enable PLLE and UPHY PLL HW PWRSEQ

This commit removes the programming sequence that enables PLLE and UPHY
PLL hardware power sequencers. Per TRM, boot software should enable PLLE
and UPHY PLLs in software controlled power-on state and should power
down PLL before jumping into kernel or the next stage boot software.

Adds call to board_cleanup_before_linux to facilitate this.

Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
4 years agoARM: tegra: p2371-2180: add I2C nodes to DT
Stephen Warren [Thu, 26 Mar 2020 22:20:45 +0000 (15:20 -0700)]
ARM: tegra: p2371-2180: add I2C nodes to DT

This adds to the DT the I2C controllers that connect to the board ID EEPROM,
etc. With this change, you can now probe all I2C devices on a TX1 board.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
4 years agocolibri_t30: add update_uboot wrapper
Igor Opaniuk [Fri, 27 Mar 2020 10:15:48 +0000 (12:15 +0200)]
colibri_t30: add update_uboot wrapper

Add universal update_uboot wrapper that helps to update
U-Boot image on internal storage.

Create an proper tegra image:
$ cbootimage -s tegra30 colibri_t30.img.cfg colibri_t30.img

Flash in U-boot shell:
> tftpboot ${loadaddr} ${board_name}/${board_name}.img
> run update_uboot

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
4 years agocolibri_t20: add update_uboot wrapper
Igor Opaniuk [Fri, 27 Mar 2020 10:15:47 +0000 (12:15 +0200)]
colibri_t20: add update_uboot wrapper

Add universal update_uboot wrapper that helps to update
U-Boot image on internal storage(NAND).

Create an proper tegra image:
$ cbootimage -s tegra20 colibri_t20-512-v12-nand.img.cfg colibri_t20.img

Flash in U-boot shell:
> tftpboot ${loadaddr} ${board_name}/${board_name}.img
> run update_uboot

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
4 years agoapalis_t30: add update_uboot wrapper
Igor Opaniuk [Fri, 27 Mar 2020 10:15:46 +0000 (12:15 +0200)]
apalis_t30: add update_uboot wrapper

Add universal update_uboot wrapper that helps to update
U-Boot image on internal storage.

Create an proper tegra image:
$ cbootimage -s tegra30 apalis_t30.img.cfg apalis_t30.img

Flash in U-boot shell:
> tftpboot ${loadaddr} ${board_name}/${board_name}.img
> run update_uboot

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
4 years agoapalis-tk1: add update_uboot wrapper
Igor Opaniuk [Fri, 27 Mar 2020 10:15:45 +0000 (12:15 +0200)]
apalis-tk1: add update_uboot wrapper

Add universal update_uboot wrapper that helps to update
U-Boot image on internal storage.

Create an proper tegra image:
$ cbootimage -s tegra124 apalis-tk1.img.cfg apalis-tk1.img

Flash in U-boot shell:
> tftpboot ${loadaddr} ${board_name}/${board_name}.img
> run update_uboot

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
4 years agoMerge tag 'video-fixes-2apr20' of https://gitlab.denx.de/u-boot/custodians/u-boot...
Tom Rini [Thu, 2 Apr 2020 16:15:17 +0000 (12:15 -0400)]
Merge tag 'video-fixes-2apr20' of https://gitlab.denx.de/u-boot/custodians/u-boot-video

- rockchip RK3399 HDMI output fix

4 years agovideo: rockchip: Support 4K resolution for rk3399, HDMI
Jagan Teki [Thu, 2 Apr 2020 11:41:25 +0000 (17:11 +0530)]
video: rockchip: Support 4K resolution for rk3399, HDMI

The default resolution for rockchip display is 1920x1080
which failed to work on 4K HDMI out displays on rk3399.

So, mark the default resolution as 3480x2160 for rk3399
HDMI out.

This would work all the hdmi display resolutions till
4K.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
4 years agorockchip: Enable HDMI output on rk3399 board w/ HDMI
Jagan Teki [Thu, 2 Apr 2020 11:41:24 +0000 (17:11 +0530)]
rockchip: Enable HDMI output on rk3399 board w/ HDMI

Enable config options and console setting to respective
rk3399 board for HDMI output.

Boards supported and tested on this patch are:
- NanoPc T4
- NanoPi M4
- NanoPi Neo4
- ROC-RK3399-PC
- Rock960

Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
4 years agorockchip: Enable pre console for rk3399
Jagan Teki [Thu, 2 Apr 2020 11:41:23 +0000 (17:11 +0530)]
rockchip: Enable pre console for rk3399

Enable pre console buffer for rk3399 platform.

This would help to capture the console messages prior to
the console being initialised. Enabling this would help
to capture all the console messages on video output source
like HDMI. So we can find the full console messages of
U-Boot proper on HDMI display when enabled it for RK3399
platform boards.

Buffer address used for pre console is 0x0f200000 which is
ram base plus 240MiB. right now the Allwinner SoC is using
similar computation.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
4 years agovideo: rockchip: Fix vop modes for rk3399
Jagan Teki [Thu, 2 Apr 2020 11:41:22 +0000 (17:11 +0530)]
video: rockchip: Fix vop modes for rk3399

VOP display endpoint pipeline configuration differs
between rk3288 vs rk3399.

These VOP pipeline configuration depends on how the
different display interfaces connected in sequence to
IN and OUT ports like for,

RK3288:

vopb_out: port {
#address-cells = <1>;
#size-cells = <0>;
vopb_out_edp: endpoint@0 {
reg = <0>;
remote-endpoint = <&edp_in_vopb>;
};
vopb_out_hdmi: endpoint@1 {
reg = <1>;
                remote-endpoint = <&hdmi_in_vopb>;
        };
        vopb_out_lvds: endpoint@2 {
                reg = <2>;
                remote-endpoint = <&lvds_in_vopb>;
        };
        vopb_out_mipi: endpoint@3 {
                reg = <3>;
                remote-endpoint = <&mipi_in_vopb>;
        };
};

RK3399:

vopb_out: port {
         #address-cells = <1>;
         #size-cells = <0>;
         vopb_out_edp: endpoint@0 {
                reg = <0>;
                remote-endpoint = <&edp_in_vopb>;
         };
         vopb_out_mipi: endpoint@1 {
                reg = <1>;
                remote-endpoint = <&mipi_in_vopb>;
         };
         vopb_out_hdmi: endpoint@2 {
                reg = <2>;
                remote-endpoint = <&hdmi_in_vopb>;
         };
         vopb_out_mipi1: endpoint@3 {
                reg = <3>;
                remote-endpoint = <&mipi1_in_vopb>;
         };
         vopb_out_dp: endpoint@4 {
                reg = <4>;
                remote-endpoint = <&dp_in_vopb>;
         };
};

here, HDMI interface has endpoint 1 in rk3288 and 2 in rk3399.

The rockchip vop driver often depends on this determined endpoint
number and stored in vop_mode. So based on this vop_mode the bpp
and pin polarity would configure on detected display interface.

Since, the existing driver using rk3288 vop mode settings enabling
the same will result wrong display interface configuration for rk3399.

Add the patch for fixing these vop modes for rk3399.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
4 years agoclk: rk3399: Set empty for vopl assigned-clocks
Jagan Teki [Thu, 2 Apr 2020 11:41:21 +0000 (17:11 +0530)]
clk: rk3399: Set empty for vopl assigned-clocks

During vidconsole probe, the device probe will try to
check whether the assigned clocks on that video console
node is initialized or not? and return an error if not.

But, unlike Linux U-Boot won't require to handle these
vopl assigned-clocks since core clocks are enough to
handle the video out to process.

So, mark them as empty in set_rate to satisfy clk_set_defaults
so-that probe happened properly.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
4 years agospi: atmel-quadspi: Add verbose debug facilities to monitor register accesses
Tudor Ambarus [Fri, 20 Mar 2020 09:37:59 +0000 (09:37 +0000)]
spi: atmel-quadspi: Add verbose debug facilities to monitor register accesses

This feature should not be enabled in release but can be useful for
developers who need to monitor register accesses at some specific places.

Helped me identify a bug in u-boot, by comparing the register accesses
from the u-boot driver with the ones from its linux variant.

Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
[jagan: use 16 bit array with tmp variable]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
4 years agospi: atmel-quadspi: fix possible MMIO window size overrun
Tudor Ambarus [Fri, 20 Mar 2020 09:37:59 +0000 (09:37 +0000)]
spi: atmel-quadspi: fix possible MMIO window size overrun

The sama5d2 QSPI controller memory space is limited to 128MB:
0x9000_00000-0x9800_00000/0XD000_0000--0XD800_0000.

There are nor flashes that are bigger in size than the memory size
supported by the controller: Micron MT25QL02G (256 MB).

Check if the address exceeds the MMIO window size. An improvement
would be to add support for regular SPI mode and fall back to it
when the flash memories overrun the controller's memory space.

Fixes: 24c8ff4684c5 ("spi: Add Atmel QuadSPI driver")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
4 years agoMerge tag 'dm-pull-1apr20' of git://git.denx.de/u-boot-dm
Tom Rini [Wed, 1 Apr 2020 18:29:21 +0000 (14:29 -0400)]
Merge tag 'dm-pull-1apr20' of git://git.denx.de/u-boot-dm

Vboot vulnerability fix

4 years agoMerge tag 'u-boot-stm32-20200401' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
Tom Rini [Wed, 1 Apr 2020 13:47:30 +0000 (09:47 -0400)]
Merge tag 'u-boot-stm32-20200401' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm

- Fix device tree of Avenger96 board from Arrow Electronics and add
  compatibility with stm32mp15_dhcom_basic_defconfig

4 years agotest: vboot: Reduce fake kernel size to 500 bytes
Simon Glass [Wed, 18 Mar 2020 17:44:08 +0000 (11:44 -0600)]
test: vboot: Reduce fake kernel size to 500 bytes

We don't need 5KB to test things out. A smaller size makes it easier to
look at the FIT with fdtdump.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agotest: vboot: Move key creation into a function
Simon Glass [Wed, 18 Mar 2020 17:44:07 +0000 (11:44 -0600)]
test: vboot: Move key creation into a function

This code is repeated so move it into a function with a parameter.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agoimage: Use constants for 'required' and 'key-name-hint'
Simon Glass [Wed, 18 Mar 2020 17:44:06 +0000 (11:44 -0600)]
image: Use constants for 'required' and 'key-name-hint'

These are used in multiple places so update them to use a shared #define.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
4 years agotest: vboot: Fix pylint errors
Simon Glass [Wed, 18 Mar 2020 17:44:05 +0000 (11:44 -0600)]
test: vboot: Fix pylint errors

Fix various minor things noticed by pylint.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agotest: vboot: Tidy up the code a little
Simon Glass [Wed, 18 Mar 2020 17:44:04 +0000 (11:44 -0600)]
test: vboot: Tidy up the code a little

Fix some long lines and comments. Use a distinct name for the
'required key' test.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agofit_check_sign: Allow selecting the configuration to verify
Simon Glass [Wed, 18 Mar 2020 17:44:03 +0000 (11:44 -0600)]
fit_check_sign: Allow selecting the configuration to verify

This tool always verifies the default configuration. It is useful to be
able to verify a specific one. Add a command-line flag for this and plumb
the logic through.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agoimage: Load the correct configuration in fit_check_sign
Simon Glass [Wed, 18 Mar 2020 17:44:02 +0000 (11:44 -0600)]
image: Load the correct configuration in fit_check_sign

At present bootm_host_load_images() is passed the configuration that has
been verified, but ignores it and just uses the default configuration.
This may not be the same.

Update this function to use the selected configuration.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agoimage: Check hash-nodes when checking configurations
Simon Glass [Wed, 18 Mar 2020 17:44:01 +0000 (11:44 -0600)]
image: Check hash-nodes when checking configurations

It is currently possible to use a different configuration's signature and
thus bypass the configuration check. Make sure that the configuration node
that was hashed matches the one being checked, to catch this problem.

Also add a proper function comment to fit_config_check_sig() and make it
static.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agotest: vboot: Parameterise the test
Simon Glass [Wed, 18 Mar 2020 17:44:00 +0000 (11:44 -0600)]
test: vboot: Parameterise the test

This test is actually made up of five separate tests. Split them out so
that they appear as separate tests.

Unfortunately this restarts U-Boot multiple times which adds about a
second to the already-long vboot test, about 8 seconds total on my
machine. We could add a special 'teardown' test afterwards but if the
tests are executed out of order that would not work.

Changing test_vboot into a class causes it not to be discovered and makes
it different from all other tests.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agotest: vboot: Add a test for a forged configuration
Simon Glass [Wed, 18 Mar 2020 17:43:59 +0000 (11:43 -0600)]
test: vboot: Add a test for a forged configuration

Add a check to make sure that it is not possible to add a new
configuration and use the hashed nodes and hash of another configuration.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agotest: vboot: Drop unnecessary parameter for fit_check_sign
Simon Glass [Wed, 18 Mar 2020 17:43:58 +0000 (11:43 -0600)]
test: vboot: Drop unnecessary parameter for fit_check_sign

This tool only uses the last -k parameter provided. Drop the earlier one
since it has no effect.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agoimage: Return an error message from fit_config_verify_sig()
Simon Glass [Wed, 18 Mar 2020 17:43:57 +0000 (11:43 -0600)]
image: Return an error message from fit_config_verify_sig()

This function only returns an error message sometimes. Update it to always
return an error message if one is available. This makes it easier to see
what went wrong.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agoimage: Be a little more verbose when checking signatures
Simon Glass [Wed, 18 Mar 2020 17:43:56 +0000 (11:43 -0600)]
image: Be a little more verbose when checking signatures

It is useful to be a little more specific about what is being checked.
Update a few messages to help with this.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agoimage: Correct comment for fit_conf_get_node()
Simon Glass [Wed, 18 Mar 2020 17:43:55 +0000 (11:43 -0600)]
image: Correct comment for fit_conf_get_node()

This should mention that conf_uname can be NULL and should be in the
header file. Fix this.

Signed-off-by: Simon Glass <sjg@chromium.org>
4 years agoARM: dts: stm32: Repair PMIC configuration on AV96
Marek Vasut [Tue, 31 Mar 2020 17:51:34 +0000 (19:51 +0200)]
ARM: dts: stm32: Repair PMIC configuration on AV96

The core and vdd PMIC buck regulators were misconfigured, which caused
instability of the board and malfunction of high-speed interfaces, like
the RGMII. Configure the PMIC correctly to repair these problems. Also,
model the missing Enpirion EP53A8LQI on the DHCOR SoM as a fixed regulator.

Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
4 years agoARM: dts: stm32: Add missing ethernet PHY reset on AV96
Marek Vasut [Tue, 31 Mar 2020 17:51:33 +0000 (19:51 +0200)]
ARM: dts: stm32: Add missing ethernet PHY reset on AV96

Add PHY reset GPIO on AV96 ethernet PHY.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
4 years agoARM: dts: stm32: Repair ethernet operation on AV96
Marek Vasut [Tue, 31 Mar 2020 17:51:32 +0000 (19:51 +0200)]
ARM: dts: stm32: Repair ethernet operation on AV96

The AV96 RGMII uses different pinmux for ETH_RGMII_TXD0, ETH_RGMII_RXD2
and ETH_RGMII_TX_CTL. Use the correct pinmux to make ethernet operational.

Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
4 years agoARM: dts: stm32: Add alternate pinmux for ethernet RGMII
Marek Vasut [Tue, 31 Mar 2020 17:51:31 +0000 (19:51 +0200)]
ARM: dts: stm32: Add alternate pinmux for ethernet RGMII

Add another mux option for DWMAC RGMII, this is used on AV96 board.

Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>