#include <common.h>
#include <console.h>
+#include <dm.h>
#include <usb.h>
#include <asm/io.h>
#include <linux/iopoll.h>
+#include <power/regulator.h>
#include "r8a66597.h"
#define R8A66597_DPRINT(...)
#endif
-static struct r8a66597 gr8a66597;
+static inline struct usb_device *usb_dev_get_parent(struct usb_device *udev)
+{
+ struct udevice *parent = udev->dev->parent;
+
+ /*
+ * When called from usb-uclass.c: usb_scan_device() udev->dev points
+ * to the parent udevice, not the actual udevice belonging to the
+ * udev as the device is not instantiated yet.
+ *
+ * If dev is an usb-bus, then we are called from usb_scan_device() for
+ * an usb-device plugged directly into the root port, return NULL.
+ */
+ if (device_get_uclass_id(udev->dev) == UCLASS_USB)
+ return NULL;
+
+ /*
+ * If these 2 are not the same we are being called from
+ * usb_scan_device() and udev itself is the parent.
+ */
+ if (dev_get_parent_priv(udev->dev) != udev)
+ return udev;
+
+ /* We are being called normally, use the parent pointer */
+ if (device_get_uclass_id(parent) == UCLASS_USB_HUB)
+ return dev_get_parent_priv(parent);
+
+ return NULL;
+}
static void get_hub_data(struct usb_device *dev, u16 *hub_devnum, u16 *hubport)
{
- int i;
+ struct usb_device *parent = usb_dev_get_parent(dev);
*hub_devnum = 0;
*hubport = 0;
/* check a device connected to root_hub */
- if ((dev->parent && dev->parent->devnum == 1) ||
- (dev->devnum == 1))
+ if ((parent && parent->devnum == 1) ||
+ dev->devnum == 1)
return;
- for (i = 0; i < USB_MAXCHILDREN; i++) {
- if (dev->parent->children[i] == dev) {
- *hub_devnum = (u8)dev->parent->devnum;
- *hubport = i;
- return;
- }
- }
-
- printf("get_hub_data error.\n");
+ *hub_devnum = (u8)parent->devnum;
+ *hubport = parent->portnr - 1;
}
static void set_devadd(struct r8a66597 *r8a66597, u8 r8a66597_address,
- struct usb_device *dev, int port)
+ struct usb_device *dev, int port)
{
u16 val, usbspd, upphub, hubport;
unsigned long devadd_reg = get_devadd_addr(r8a66597_address);
u16 tmp;
int i = 0;
-#if defined(CONFIG_SUPERH_ON_CHIP_R8A66597)
- do {
- r8a66597_write(r8a66597, SCKE, SYSCFG0);
- tmp = r8a66597_read(r8a66597, SYSCFG0);
- if (i++ > 1000) {
- printf("register access fail.\n");
- return -1;
- }
- } while ((tmp & SCKE) != SCKE);
- r8a66597_write(r8a66597, 0x04, 0x02);
-#else
do {
r8a66597_write(r8a66597, USBE, SYSCFG0);
tmp = r8a66597_read(r8a66597, SYSCFG0);
}
} while ((tmp & USBE) != USBE);
r8a66597_bclr(r8a66597, USBE, SYSCFG0);
-#if !defined(CONFIG_RZA_USB)
- r8a66597_mdfy(r8a66597, CONFIG_R8A66597_XTAL, XTAL, SYSCFG0);
-
- i = 0;
- r8a66597_bset(r8a66597, XCKE, SYSCFG0);
- do {
- udelay(1000);
- tmp = r8a66597_read(r8a66597, SYSCFG0);
- if (i++ > 500) {
- printf("register access fail.\n");
- return -1;
- }
- } while ((tmp & SCKE) != SCKE);
-#else
/*
* RZ/A Only:
* Bits XTAL(UCKSEL) and UPLLE in SYSCFG0 for USB0 controls both USB0
* and USB1, so we must always set the USB0 register
*/
#if (CONFIG_R8A66597_XTAL == 1)
- setbits(le16, R8A66597_BASE0, XTAL);
+ r8a66597_bset(r8a66597, XTAL, SYSCFG0);
#endif
mdelay(1);
- setbits(le16, R8A66597_BASE0, UPLLE);
+ r8a66597_bset(r8a66597, UPLLE, SYSCFG0);
mdelay(1);
r8a66597_bset(r8a66597, SUSPM, SUSPMODE0);
-#endif /* CONFIG_RZA_USB */
-#endif /* #if defined(CONFIG_SUPERH_ON_CHIP_R8A66597) */
return 0;
}
static void r8a66597_clock_disable(struct r8a66597 *r8a66597)
{
-#if !defined(CONFIG_RZA_USB)
- r8a66597_bclr(r8a66597, SCKE, SYSCFG0);
- udelay(1);
-#if !defined(CONFIG_SUPERH_ON_CHIP_R8A66597)
- r8a66597_bclr(r8a66597, PLLC, SYSCFG0);
- r8a66597_bclr(r8a66597, XCKE, SYSCFG0);
- r8a66597_bclr(r8a66597, USBE, SYSCFG0);
-#endif
-#else
r8a66597_bclr(r8a66597, SUSPM, SUSPMODE0);
- clrbits(le16, R8A66597_BASE0, UPLLE);
+ r8a66597_bclr(r8a66597, UPLLE, SYSCFG0);
mdelay(1);
r8a66597_bclr(r8a66597, USBE, SYSCFG0);
mdelay(1);
-
-#endif
}
static void r8a66597_enable_port(struct r8a66597 *r8a66597, int port)
val = port ? DRPD : DCFM | DRPD;
r8a66597_bset(r8a66597, val, get_syscfg_reg(port));
r8a66597_bset(r8a66597, HSE, get_syscfg_reg(port));
-
-#if !defined(CONFIG_RZA_USB)
- r8a66597_write(r8a66597, BURST | CPU_ADR_RD_WR, get_dmacfg_reg(port));
-#endif
}
static void r8a66597_disable_port(struct r8a66597 *r8a66597, int port)
if (ret < 0)
return ret;
-#if !defined(CONFIG_RZA_USB)
- r8a66597_bset(r8a66597, CONFIG_R8A66597_LDRV & LDRV, PINCFG);
-#endif
r8a66597_bset(r8a66597, USBE, SYSCFG0);
r8a66597_bset(r8a66597, INTL, SOFCFG);
for (port = 0; port < R8A66597_MAX_ROOT_HUB; port++)
r8a66597_write(r8a66597, 0, get_intenb_reg(port));
- r8a66597_bset(r8a66597, CONFIG_R8A66597_ENDIAN & BIGEND, CFIFOSEL);
- r8a66597_bset(r8a66597, CONFIG_R8A66597_ENDIAN & BIGEND, D0FIFOSEL);
- r8a66597_bset(r8a66597, CONFIG_R8A66597_ENDIAN & BIGEND, D1FIFOSEL);
+ r8a66597_bclr(r8a66597, BIGEND, CFIFOSEL);
+ r8a66597_bclr(r8a66597, BIGEND, D0FIFOSEL);
+ r8a66597_bclr(r8a66597, BIGEND, D1FIFOSEL);
r8a66597_bset(r8a66597, TRNENSEL, SOFCFG);
for (port = 0; port < R8A66597_MAX_ROOT_HUB; port++)
unsigned long setup_addr = USBREQ;
u16 intsts1;
int timeout = 3000;
-#if defined(CONFIG_RZA_USB)
u16 dcpctr;
-#endif
u16 devsel = setup->request == USB_REQ_SET_ADDRESS ? 0 : dev->devnum;
r8a66597_write(r8a66597, make_devsel(devsel) |
(8 << dev->maxpacketsize), DCPMAXP);
r8a66597_write(r8a66597, ~(SIGN | SACK), INTSTS1);
-#if defined(CONFIG_RZA_USB)
dcpctr = r8a66597_read(r8a66597, DCPCTR);
if ((dcpctr & PID) == PID_BUF) {
if (readw_poll_timeout(r8a66597->reg + DCPCTR, dcpctr,
return -ETIMEDOUT;
}
}
-#endif
for (i = 0; i < 4; i++) {
r8a66597_write(r8a66597, le16_to_cpu(p[i]), setup_addr);
R8A66597_DPRINT("%s\n", __func__);
r8a66597_mdfy(r8a66597, MBW | BULK_OUT_PIPENUM,
- MBW | CURPIPE, CFIFOSEL);
+ MBW | CURPIPE, CFIFOSEL);
r8a66597_reg_wait(r8a66597, CFIFOSEL, CURPIPE, BULK_OUT_PIPENUM);
tmp = r8a66597_read(r8a66597, CFIFOCTR);
if ((tmp & FRDY) == 0) {
dev->act_len += size;
r8a66597_mdfy(r8a66597, PID_BUF, PID,
- get_pipectr_addr(BULK_OUT_PIPENUM));
+ get_pipectr_addr(BULK_OUT_PIPENUM));
while (!(r8a66597_read(r8a66597, BEMPSTS) & (1 << BULK_OUT_PIPENUM)))
if (ctrlc())
if (dev->act_len >= transfer_len)
r8a66597_mdfy(r8a66597, PID_NAK, PID,
- get_pipectr_addr(BULK_OUT_PIPENUM));
+ get_pipectr_addr(BULK_OUT_PIPENUM));
return 0;
}
/* prepare */
if (dev->act_len == 0) {
r8a66597_mdfy(r8a66597, PID_NAK, PID,
- get_pipectr_addr(pipenum));
+ get_pipectr_addr(pipenum));
r8a66597_write(r8a66597, ~(1 << pipenum), BRDYSTS);
r8a66597_write(r8a66597, TRCLR, get_pipetre_addr(pipenum));
r8a66597_write(r8a66597,
- (transfer_len + maxpacket - 1) / maxpacket,
+ (transfer_len + maxpacket - 1) / maxpacket,
get_pipetrn_addr(pipenum));
r8a66597_bset(r8a66597, TRENB, get_pipetre_addr(pipenum));
r8a66597_mdfy(r8a66597, PID_BUF, PID,
- get_pipectr_addr(pipenum));
+ get_pipectr_addr(pipenum));
}
r8a66597_mdfy(r8a66597, MBW | pipenum, MBW | CURPIPE, CFIFOSEL);
}
static int send_status_packet(struct r8a66597 *r8a66597,
- unsigned long pipe)
+ unsigned long pipe)
{
r8a66597_bset(r8a66597, SQSET, DCPCTR);
r8a66597_mdfy(r8a66597, PID_NAK, PID, DCPCTR);
return -1; /* fail */
}
-/*-------------------------------------------------------------------------*
- * Virtual Root Hub
- *-------------------------------------------------------------------------*/
+/* Virtual Root Hub */
#include <usbroothubdes.h>
-static int r8a66597_submit_rh_msg(struct usb_device *dev, unsigned long pipe,
- void *buffer, int transfer_len, struct devrequest *cmd)
+static int r8a66597_submit_rh_msg(struct udevice *udev, struct usb_device *dev,
+ unsigned long pipe, void *buffer,
+ int transfer_len, struct devrequest *cmd)
{
- struct r8a66597 *r8a66597 = &gr8a66597;
+ struct r8a66597 *r8a66597 = dev_get_priv(udev);
int leni = transfer_len;
int len = 0;
int stat = 0;
}
break;
case RH_SET_ADDRESS:
- gr8a66597.rh_devnum = wValue;
+ r8a66597->rh_devnum = wValue;
break;
case RH_GET_DESCRIPTOR:
switch ((wValue & 0xff00) >> 8) {
case (0x01): /* device descriptor */
len = min_t(unsigned int,
- leni,
+ leni,
min_t(unsigned int,
- sizeof(root_hub_dev_des),
+ sizeof(root_hub_dev_des),
wLength));
memcpy(buffer, root_hub_dev_des, len);
break;
case (0x02): /* configuration descriptor */
len = min_t(unsigned int,
- leni,
+ leni,
min_t(unsigned int,
- sizeof(root_hub_config_des),
+ sizeof(root_hub_config_des),
wLength));
memcpy(buffer, root_hub_config_des, len);
break;
case (0x03): /* string descriptors */
if (wValue == 0x0300) {
len = min_t(unsigned int,
- leni,
+ leni,
min_t(unsigned int,
- sizeof(root_hub_str_index0),
+ sizeof(root_hub_str_index0),
wLength));
memcpy(buffer, root_hub_str_index0, len);
}
if (wValue == 0x0301) {
len = min_t(unsigned int,
- leni,
+ leni,
min_t(unsigned int,
- sizeof(root_hub_str_index1),
+ sizeof(root_hub_str_index1),
wLength));
memcpy(buffer, root_hub_str_index1, len);
}
} else {
data[0] += 2;
data[8] = (temp & RH_B_DR) >> 8;
- data[10] = data[9] = 0xff;
+ data[9] = 0xff;
+ data[10] = 0xff;
}
len = min_t(unsigned int, leni,
}
case RH_GET_CONFIGURATION:
- *(__u8 *) buffer = 0x01;
+ *(__u8 *)buffer = 0x01;
len = 1;
break;
case RH_SET_CONFIGURATION:
return stat;
}
-int submit_bulk_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
- int transfer_len)
+static int r8a66597_submit_control_msg(struct udevice *udev,
+ struct usb_device *dev,
+ unsigned long pipe, void *buffer,
+ int length, struct devrequest *setup)
{
- struct r8a66597 *r8a66597 = &gr8a66597;
- int ret = 0;
-
- R8A66597_DPRINT("%s\n", __func__);
- R8A66597_DPRINT("pipe = %08x, buffer = %p, len = %d, devnum = %d\n",
- pipe, buffer, transfer_len, dev->devnum);
-
- set_devadd(r8a66597, dev->devnum, dev, 0);
-
- pipe_buffer_setting(r8a66597, dev, pipe);
-
- dev->act_len = 0;
- while (dev->act_len < transfer_len && ret == 0) {
- if (ctrlc())
- return -1;
-
- if (usb_pipein(pipe))
- ret = receive_bulk_packet(r8a66597, dev, pipe, buffer,
- transfer_len);
- else
- ret = send_bulk_packet(r8a66597, dev, pipe, buffer,
- transfer_len);
- }
-
- if (ret == 0)
- dev->status = 0;
-
- return ret;
-}
-
-int submit_control_msg(struct usb_device *dev, unsigned long pipe,
- void *buffer, int transfer_len, struct devrequest *setup)
-{
- struct r8a66597 *r8a66597 = &gr8a66597;
+ struct r8a66597 *r8a66597 = dev_get_priv(udev);
u16 r8a66597_address = setup->request == USB_REQ_SET_ADDRESS ?
0 : dev->devnum;
+ debug("%s: dev='%s', udev=%p, udev->dev='%s', portnr=%d\n", __func__,
+ udev->name, dev, dev->dev->name, dev->portnr);
+
R8A66597_DPRINT("%s\n", __func__);
if (usb_pipedevice(pipe) == r8a66597->rh_devnum)
- return r8a66597_submit_rh_msg(dev, pipe, buffer, transfer_len,
- setup);
+ return r8a66597_submit_rh_msg(udev, dev, pipe, buffer,
+ length, setup);
R8A66597_DPRINT("%s: setup\n", __func__);
set_devadd(r8a66597, r8a66597_address, dev, 0);
dev->act_len = 0;
if (usb_pipein(pipe))
if (receive_control_packet(r8a66597, dev, buffer,
- transfer_len) < 0)
+ length) < 0)
return -1;
if (send_status_packet(r8a66597, pipe) < 0)
return 0;
}
-int submit_int_msg(struct usb_device *dev, unsigned long pipe, void *buffer,
- int transfer_len, int interval)
+static int r8a66597_submit_bulk_msg(struct udevice *udev,
+ struct usb_device *dev, unsigned long pipe,
+ void *buffer, int length)
{
- /* no implement */
+ struct r8a66597 *r8a66597 = dev_get_priv(udev);
+ int ret = 0;
+
+ debug("%s: dev='%s', udev=%p\n", __func__, udev->name, dev);
+
R8A66597_DPRINT("%s\n", __func__);
- return 0;
+ R8A66597_DPRINT("pipe = %08x, buffer = %p, len = %d, devnum = %d\n",
+ pipe, buffer, length, dev->devnum);
+
+ set_devadd(r8a66597, dev->devnum, dev, 0);
+
+ pipe_buffer_setting(r8a66597, dev, pipe);
+
+ dev->act_len = 0;
+ while (dev->act_len < length && ret == 0) {
+ if (ctrlc())
+ return -1;
+
+ if (usb_pipein(pipe))
+ ret = receive_bulk_packet(r8a66597, dev, pipe, buffer,
+ length);
+ else
+ ret = send_bulk_packet(r8a66597, dev, pipe, buffer,
+ length);
+ }
+
+ if (ret == 0)
+ dev->status = 0;
+
+ return ret;
}
-int usb_lowlevel_init(int index, enum usb_init_type init, void **controller)
+static int r8a66597_usb_ofdata_to_platdata(struct udevice *dev)
{
- struct r8a66597 *r8a66597 = &gr8a66597;
+ struct r8a66597 *priv = dev_get_priv(dev);
+ fdt_addr_t addr;
- R8A66597_DPRINT("%s\n", __func__);
+ addr = dev_read_addr(dev);
+ if (addr == FDT_ADDR_T_NONE)
+ return -EINVAL;
+ priv->reg = addr;
- memset(r8a66597, 0, sizeof(*r8a66597));
- r8a66597->reg = CONFIG_R8A66597_BASE_ADDR;
+ return 0;
+}
+
+static int r8a66597_usb_probe(struct udevice *dev)
+{
+ struct r8a66597 *priv = dev_get_priv(dev);
+ struct usb_bus_priv *bus_priv = dev_get_uclass_priv(dev);
+ int ret;
+
+ bus_priv->desc_before_addr = true;
+
+ if (CONFIG_IS_ENABLED(DM_REGULATOR)) {
+ ret = device_get_supply_regulator(dev, "vbus-supply",
+ &priv->vbus_supply);
+ if (ret) {
+ dev_err(dev,
+ "can't get VBUS supply\n");
+ return ret;
+ }
+
+ ret = regulator_set_enable(priv->vbus_supply, true);
+ if (ret) {
+ dev_err(dev,
+ "can't enable VBUS supply\n");
+ return ret;
+ }
+ }
- disable_controller(r8a66597);
+ disable_controller(priv);
mdelay(100);
- enable_controller(r8a66597);
- r8a66597_port_power(r8a66597, 0 , 1);
+ enable_controller(priv);
+ r8a66597_port_power(priv, 0, 1);
/* check usb device */
- check_usb_device_connecting(r8a66597);
+ check_usb_device_connecting(priv);
mdelay(50);
return 0;
}
-int usb_lowlevel_stop(int index)
+static int r8a66597_usb_remove(struct udevice *dev)
{
- disable_controller(&gr8a66597);
+ struct r8a66597 *priv = dev_get_priv(dev);
+ int ret;
+
+ disable_controller(priv);
+
+ if (CONFIG_IS_ENABLED(DM_REGULATOR)) {
+ ret = regulator_set_enable(priv->vbus_supply, false);
+ if (ret) {
+ dev_err(dev,
+ "can't disable VBUS supply\n");
+ return ret;
+ }
+ }
return 0;
}
+
+struct dm_usb_ops r8a66597_usb_ops = {
+ .control = r8a66597_submit_control_msg,
+ .bulk = r8a66597_submit_bulk_msg,
+};
+
+static const struct udevice_id r8a66597_usb_ids[] = {
+ { .compatible = "renesas,rza1-usbhs" },
+ { }
+};
+
+U_BOOT_DRIVER(usb_r8a66597) = {
+ .name = "r8a66597_usb",
+ .id = UCLASS_USB,
+ .of_match = r8a66597_usb_ids,
+ .ofdata_to_platdata = r8a66597_usb_ofdata_to_platdata,
+ .probe = r8a66597_usb_probe,
+ .remove = r8a66597_usb_remove,
+ .ops = &r8a66597_usb_ops,
+ .priv_auto_alloc_size = sizeof(struct r8a66597),
+ .flags = DM_FLAG_ALLOC_PRIV_DMA,
+};
#define PIPE3TRE 0x98
#define PIPE3TRN 0x9A
#define PIPE4TRE 0x9C
-#define PIPE4TRN 0x9E
-#define PIPE5TRE 0xA0
-#define PIPE5TRN 0xA2
+#define PIPE4TRN 0x9E
+#define PIPE5TRE 0xA0
+#define PIPE5TRN 0xA2
#define DEVADD0 0xD0
#define DEVADD1 0xD2
#define DEVADD2 0xD4
#define SUSPMODE0 0x102 /* RZ/A only */
/* System Configuration Control Register */
-#if !defined(CONFIG_RZA_USB)
-#define XTAL 0xC000 /* b15-14: Crystal selection */
-#define XTAL48 0x8000 /* 48MHz */
-#define XTAL24 0x4000 /* 24MHz */
-#define XTAL12 0x0000 /* 12MHz */
-#define XCKE 0x2000 /* b13: External clock enable */
-#define PLLC 0x0800 /* b11: PLL control */
-#define SCKE 0x0400 /* b10: USB clock enable */
-#define PCSDIS 0x0200 /* b9: not CS wakeup */
-#define LPSME 0x0100 /* b8: Low power sleep mode */
-#endif
-#define HSE 0x0080 /* b7: Hi-speed enable */
-#define DCFM 0x0040 /* b6: Controller function select */
-#define DRPD 0x0020 /* b5: D+/- pull down control */
-#define DPRPU 0x0010 /* b4: D+ pull up control */
-#if defined(CONFIG_RZA_USB)
-#define XTAL 0x0004 /* b2: Crystal selection */
-#define XTAL12 0x0004 /* 12MHz */
-#define XTAL48 0x0000 /* 48MHz */
-#define UPLLE 0x0002 /* b1: internal PLL control */
-#endif
-#define USBE 0x0001 /* b0: USB module operation enable */
+#define HSE 0x0080 /* b7: Hi-speed enable */
+#define DCFM 0x0040 /* b6: Controller function select */
+#define DRPD 0x0020 /* b5: D+/- pull down control */
+#define DPRPU 0x0010 /* b4: D+ pull up control */
+#define XTAL 0x0004 /* b2: Crystal selection */
+#define XTAL12 0x0004 /* 12MHz */
+#define XTAL48 0x0000 /* 48MHz */
+#define UPLLE 0x0002 /* b1: internal PLL control */
+#define USBE 0x0001 /* b0: USB module operation enable */
/* System Configuration Status Register */
-#define OVCBIT 0x8000 /* b15-14: Over-current bit */
-#define OVCMON 0xC000 /* b15-14: Over-current monitor */
-#define SOFEA 0x0020 /* b5: SOF monitor */
-#define IDMON 0x0004 /* b3: ID-pin monitor */
-#define LNST 0x0003 /* b1-0: D+, D- line status */
-#define SE1 0x0003 /* SE1 */
-#define FS_KSTS 0x0002 /* Full-Speed K State */
-#define FS_JSTS 0x0001 /* Full-Speed J State */
-#define LS_JSTS 0x0002 /* Low-Speed J State */
-#define LS_KSTS 0x0001 /* Low-Speed K State */
-#define SE0 0x0000 /* SE0 */
+#define OVCBIT 0x8000 /* b15-14: Over-current bit */
+#define OVCMON 0xC000 /* b15-14: Over-current monitor */
+#define SOFEA 0x0020 /* b5: SOF monitor */
+#define IDMON 0x0004 /* b3: ID-pin monitor */
+#define LNST 0x0003 /* b1-0: D+, D- line status */
+#define SE1 0x0003 /* SE1 */
+#define FS_KSTS 0x0002 /* Full-Speed K State */
+#define FS_JSTS 0x0001 /* Full-Speed J State */
+#define LS_JSTS 0x0002 /* Low-Speed J State */
+#define LS_KSTS 0x0001 /* Low-Speed K State */
+#define SE0 0x0000 /* SE0 */
/* Device State Control Register */
-#define EXTLP0 0x0400 /* b10: External port */
-#define VBOUT 0x0200 /* b9: VBUS output */
-#define WKUP 0x0100 /* b8: Remote wakeup */
-#define RWUPE 0x0080 /* b7: Remote wakeup sense */
-#define USBRST 0x0040 /* b6: USB reset enable */
-#define RESUME 0x0020 /* b5: Resume enable */
-#define UACT 0x0010 /* b4: USB bus enable */
-#define RHST 0x0007 /* b1-0: Reset handshake status */
-#define HSPROC 0x0004 /* HS handshake is processing */
-#define HSMODE 0x0003 /* Hi-Speed mode */
-#define FSMODE 0x0002 /* Full-Speed mode */
-#define LSMODE 0x0001 /* Low-Speed mode */
-#define UNDECID 0x0000 /* Undecided */
+#define EXTLP0 0x0400 /* b10: External port */
+#define VBOUT 0x0200 /* b9: VBUS output */
+#define WKUP 0x0100 /* b8: Remote wakeup */
+#define RWUPE 0x0080 /* b7: Remote wakeup sense */
+#define USBRST 0x0040 /* b6: USB reset enable */
+#define RESUME 0x0020 /* b5: Resume enable */
+#define UACT 0x0010 /* b4: USB bus enable */
+#define RHST 0x0007 /* b1-0: Reset handshake status */
+#define HSPROC 0x0004 /* HS handshake is processing */
+#define HSMODE 0x0003 /* Hi-Speed mode */
+#define FSMODE 0x0002 /* Full-Speed mode */
+#define LSMODE 0x0001 /* Low-Speed mode */
+#define UNDECID 0x0000 /* Undecided */
/* Test Mode Register */
-#define UTST 0x000F /* b3-0: Test select */
-#define H_TST_PACKET 0x000C /* HOST TEST Packet */
-#define H_TST_SE0_NAK 0x000B /* HOST TEST SE0 NAK */
-#define H_TST_K 0x000A /* HOST TEST K */
-#define H_TST_J 0x0009 /* HOST TEST J */
-#define H_TST_NORMAL 0x0000 /* HOST Normal Mode */
-#define P_TST_PACKET 0x0004 /* PERI TEST Packet */
-#define P_TST_SE0_NAK 0x0003 /* PERI TEST SE0 NAK */
-#define P_TST_K 0x0002 /* PERI TEST K */
-#define P_TST_J 0x0001 /* PERI TEST J */
-#define P_TST_NORMAL 0x0000 /* PERI Normal Mode */
+#define UTST 0x000F /* b3-0: Test select */
+#define H_TST_PACKET 0x000C /* HOST TEST Packet */
+#define H_TST_SE0_NAK 0x000B /* HOST TEST SE0 NAK */
+#define H_TST_K 0x000A /* HOST TEST K */
+#define H_TST_J 0x0009 /* HOST TEST J */
+#define H_TST_NORMAL 0x0000 /* HOST Normal Mode */
+#define P_TST_PACKET 0x0004 /* PERI TEST Packet */
+#define P_TST_SE0_NAK 0x0003 /* PERI TEST SE0 NAK */
+#define P_TST_K 0x0002 /* PERI TEST K */
+#define P_TST_J 0x0001 /* PERI TEST J */
+#define P_TST_NORMAL 0x0000 /* PERI Normal Mode */
/* Data Pin Configuration Register */
-#define LDRV 0x8000 /* b15: Drive Current Adjust */
-#define VIF1 0x0000 /* VIF = 1.8V */
-#define VIF3 0x8000 /* VIF = 3.3V */
-#define INTA 0x0001 /* b1: USB INT-pin active */
+#define LDRV 0x8000 /* b15: Drive Current Adjust */
+#define VIF1 0x0000 /* VIF = 1.8V */
+#define VIF3 0x8000 /* VIF = 3.3V */
+#define INTA 0x0001 /* b1: USB INT-pin active */
/* DMAx Pin Configuration Register */
-#define DREQA 0x4000 /* b14: Dreq active select */
-#define BURST 0x2000 /* b13: Burst mode */
-#define DACKA 0x0400 /* b10: Dack active select */
-#define DFORM 0x0380 /* b9-7: DMA mode select */
-#define CPU_ADR_RD_WR 0x0000 /* Address + RD/WR mode (CPU bus) */
-#define CPU_DACK_RD_WR 0x0100 /* DACK + RD/WR mode (CPU bus) */
-#define CPU_DACK_ONLY 0x0180 /* DACK only mode (CPU bus) */
-#define SPLIT_DACK_ONLY 0x0200 /* DACK only mode (SPLIT bus) */
-#define DENDA 0x0040 /* b6: Dend active select */
-#define PKTM 0x0020 /* b5: Packet mode */
-#define DENDE 0x0010 /* b4: Dend enable */
-#define OBUS 0x0004 /* b2: OUTbus mode */
+#define DREQA 0x4000 /* b14: Dreq active select */
+#define BURST 0x2000 /* b13: Burst mode */
+#define DACKA 0x0400 /* b10: Dack active select */
+#define DFORM 0x0380 /* b9-7: DMA mode select */
+#define CPU_ADR_RD_WR 0x0000 /* Address + RD/WR mode (CPU bus) */
+#define CPU_DACK_RD_WR 0x0100 /* DACK + RD/WR mode (CPU bus) */
+#define CPU_DACK_ONLY 0x0180 /* DACK only mode (CPU bus) */
+#define SPLIT_DACK_ONLY 0x0200 /* DACK only mode (SPLIT bus) */
+#define DENDA 0x0040 /* b6: Dend active select */
+#define PKTM 0x0020 /* b5: Packet mode */
+#define DENDE 0x0010 /* b4: Dend enable */
+#define OBUS 0x0004 /* b2: OUTbus mode */
/* CFIFO/DxFIFO Port Select Register */
-#define RCNT 0x8000 /* b15: Read count mode */
-#define REW 0x4000 /* b14: Buffer rewind */
-#define DCLRM 0x2000 /* b13: DMA buffer clear mode */
-#define DREQE 0x1000 /* b12: DREQ output enable */
-#if defined(CONFIG_SUPERH_ON_CHIP_R8A66597)
-#define MBW 0x0800
-#else
-#if !defined(CONFIG_RZA_USB)
-#define MBW 0x0400 /* b10: Maximum bit width for FIFO access */
-#else
-#define MBW 0x0800 /* b10: Maximum bit width for FIFO access */
-#endif
-#endif
-#define MBW_8 0x0000 /* 8bit */
-#define MBW_16 0x0400 /* 16bit */
-#define MBW_32 0x0800 /* 32bit */
-#define BIGEND 0x0100 /* b8: Big endian mode */
-#define BYTE_LITTLE 0x0000 /* little dendian */
-#define BYTE_BIG 0x0100 /* big endifan */
-#define ISEL 0x0020 /* b5: DCP FIFO port direction select */
-#define CURPIPE 0x000F /* b2-0: PIPE select */
+#define RCNT 0x8000 /* b15: Read count mode */
+#define REW 0x4000 /* b14: Buffer rewind */
+#define DCLRM 0x2000 /* b13: DMA buffer clear mode */
+#define DREQE 0x1000 /* b12: DREQ output enable */
+#define MBW 0x0800 /* b10: Maximum bit width for FIFO access */
+#define MBW_8 0x0000 /* 8bit */
+#define MBW_16 0x0400 /* 16bit */
+#define MBW_32 0x0800 /* 32bit */
+#define BIGEND 0x0100 /* b8: Big endian mode */
+#define BYTE_LITTLE 0x0000 /* little dendian */
+#define BYTE_BIG 0x0100 /* big endifan */
+#define ISEL 0x0020 /* b5: DCP FIFO port direction select */
+#define CURPIPE 0x000F /* b2-0: PIPE select */
/* CFIFO/DxFIFO Port Control Register */
-#define BVAL 0x8000 /* b15: Buffer valid flag */
-#define BCLR 0x4000 /* b14: Buffer clear */
-#define FRDY 0x2000 /* b13: FIFO ready */
-#define DTLN 0x0FFF /* b11-0: FIFO received data length */
+#define BVAL 0x8000 /* b15: Buffer valid flag */
+#define BCLR 0x4000 /* b14: Buffer clear */
+#define FRDY 0x2000 /* b13: FIFO ready */
+#define DTLN 0x0FFF /* b11-0: FIFO received data length */
/* Interrupt Enable Register 0 */
-#define VBSE 0x8000 /* b15: VBUS interrupt */
-#define RSME 0x4000 /* b14: Resume interrupt */
-#define SOFE 0x2000 /* b13: Frame update interrupt */
-#define DVSE 0x1000 /* b12: Device state transition interrupt */
-#define CTRE 0x0800 /* b11: Control transfer stage transition interrupt */
-#define BEMPE 0x0400 /* b10: Buffer empty interrupt */
-#define NRDYE 0x0200 /* b9: Buffer not ready interrupt */
-#define BRDYE 0x0100 /* b8: Buffer ready interrupt */
+#define VBSE 0x8000 /* b15: VBUS interrupt */
+#define RSME 0x4000 /* b14: Resume interrupt */
+#define SOFE 0x2000 /* b13: Frame update interrupt */
+#define DVSE 0x1000 /* b12: Device state transition interrupt */
+#define CTRE 0x0800 /* b11: Control transfer stage transition interrupt */
+#define BEMPE 0x0400 /* b10: Buffer empty interrupt */
+#define NRDYE 0x0200 /* b9: Buffer not ready interrupt */
+#define BRDYE 0x0100 /* b8: Buffer ready interrupt */
/* Interrupt Enable Register 1 */
-#define OVRCRE 0x8000 /* b15: Over-current interrupt */
-#define BCHGE 0x4000 /* b14: USB us chenge interrupt */
-#define DTCHE 0x1000 /* b12: Detach sense interrupt */
-#define ATTCHE 0x0800 /* b11: Attach sense interrupt */
-#define EOFERRE 0x0040 /* b6: EOF error interrupt */
-#define SIGNE 0x0020 /* b5: SETUP IGNORE interrupt */
-#define SACKE 0x0010 /* b4: SETUP ACK interrupt */
+#define OVRCRE 0x8000 /* b15: Over-current interrupt */
+#define BCHGE 0x4000 /* b14: USB us chenge interrupt */
+#define DTCHE 0x1000 /* b12: Detach sense interrupt */
+#define ATTCHE 0x0800 /* b11: Attach sense interrupt */
+#define EOFERRE 0x0040 /* b6: EOF error interrupt */
+#define SIGNE 0x0020 /* b5: SETUP IGNORE interrupt */
+#define SACKE 0x0010 /* b4: SETUP ACK interrupt */
/* BRDY Interrupt Enable/Status Register */
-#define BRDY9 0x0200 /* b9: PIPE9 */
-#define BRDY8 0x0100 /* b8: PIPE8 */
-#define BRDY7 0x0080 /* b7: PIPE7 */
-#define BRDY6 0x0040 /* b6: PIPE6 */
-#define BRDY5 0x0020 /* b5: PIPE5 */
-#define BRDY4 0x0010 /* b4: PIPE4 */
-#define BRDY3 0x0008 /* b3: PIPE3 */
-#define BRDY2 0x0004 /* b2: PIPE2 */
-#define BRDY1 0x0002 /* b1: PIPE1 */
-#define BRDY0 0x0001 /* b1: PIPE0 */
+#define BRDY9 0x0200 /* b9: PIPE9 */
+#define BRDY8 0x0100 /* b8: PIPE8 */
+#define BRDY7 0x0080 /* b7: PIPE7 */
+#define BRDY6 0x0040 /* b6: PIPE6 */
+#define BRDY5 0x0020 /* b5: PIPE5 */
+#define BRDY4 0x0010 /* b4: PIPE4 */
+#define BRDY3 0x0008 /* b3: PIPE3 */
+#define BRDY2 0x0004 /* b2: PIPE2 */
+#define BRDY1 0x0002 /* b1: PIPE1 */
+#define BRDY0 0x0001 /* b1: PIPE0 */
/* NRDY Interrupt Enable/Status Register */
-#define NRDY9 0x0200 /* b9: PIPE9 */
-#define NRDY8 0x0100 /* b8: PIPE8 */
-#define NRDY7 0x0080 /* b7: PIPE7 */
-#define NRDY6 0x0040 /* b6: PIPE6 */
-#define NRDY5 0x0020 /* b5: PIPE5 */
-#define NRDY4 0x0010 /* b4: PIPE4 */
-#define NRDY3 0x0008 /* b3: PIPE3 */
-#define NRDY2 0x0004 /* b2: PIPE2 */
-#define NRDY1 0x0002 /* b1: PIPE1 */
-#define NRDY0 0x0001 /* b1: PIPE0 */
+#define NRDY9 0x0200 /* b9: PIPE9 */
+#define NRDY8 0x0100 /* b8: PIPE8 */
+#define NRDY7 0x0080 /* b7: PIPE7 */
+#define NRDY6 0x0040 /* b6: PIPE6 */
+#define NRDY5 0x0020 /* b5: PIPE5 */
+#define NRDY4 0x0010 /* b4: PIPE4 */
+#define NRDY3 0x0008 /* b3: PIPE3 */
+#define NRDY2 0x0004 /* b2: PIPE2 */
+#define NRDY1 0x0002 /* b1: PIPE1 */
+#define NRDY0 0x0001 /* b1: PIPE0 */
/* BEMP Interrupt Enable/Status Register */
-#define BEMP9 0x0200 /* b9: PIPE9 */
-#define BEMP8 0x0100 /* b8: PIPE8 */
-#define BEMP7 0x0080 /* b7: PIPE7 */
-#define BEMP6 0x0040 /* b6: PIPE6 */
-#define BEMP5 0x0020 /* b5: PIPE5 */
-#define BEMP4 0x0010 /* b4: PIPE4 */
-#define BEMP3 0x0008 /* b3: PIPE3 */
-#define BEMP2 0x0004 /* b2: PIPE2 */
-#define BEMP1 0x0002 /* b1: PIPE1 */
-#define BEMP0 0x0001 /* b0: PIPE0 */
+#define BEMP9 0x0200 /* b9: PIPE9 */
+#define BEMP8 0x0100 /* b8: PIPE8 */
+#define BEMP7 0x0080 /* b7: PIPE7 */
+#define BEMP6 0x0040 /* b6: PIPE6 */
+#define BEMP5 0x0020 /* b5: PIPE5 */
+#define BEMP4 0x0010 /* b4: PIPE4 */
+#define BEMP3 0x0008 /* b3: PIPE3 */
+#define BEMP2 0x0004 /* b2: PIPE2 */
+#define BEMP1 0x0002 /* b1: PIPE1 */
+#define BEMP0 0x0001 /* b0: PIPE0 */
/* SOF Pin Configuration Register */
-#define TRNENSEL 0x0100 /* b8: Select transaction enable period */
-#define BRDYM 0x0040 /* b6: BRDY clear timing */
-#define INTL 0x0020 /* b5: Interrupt sense select */
-#define EDGESTS 0x0010 /* b4: */
-#define SOFMODE 0x000C /* b3-2: SOF pin select */
-#define SOF_125US 0x0008 /* SOF OUT 125us Frame Signal */
-#define SOF_1MS 0x0004 /* SOF OUT 1ms Frame Signal */
-#define SOF_DISABLE 0x0000 /* SOF OUT Disable */
+#define TRNENSEL 0x0100 /* b8: Select transaction enable period */
+#define BRDYM 0x0040 /* b6: BRDY clear timing */
+#define INTL 0x0020 /* b5: Interrupt sense select */
+#define EDGESTS 0x0010 /* b4: */
+#define SOFMODE 0x000C /* b3-2: SOF pin select */
+#define SOF_125US 0x0008 /* SOF OUT 125us Frame Signal */
+#define SOF_1MS 0x0004 /* SOF OUT 1ms Frame Signal */
+#define SOF_DISABLE 0x0000 /* SOF OUT Disable */
/* Interrupt Status Register 0 */
-#define VBINT 0x8000 /* b15: VBUS interrupt */
-#define RESM 0x4000 /* b14: Resume interrupt */
-#define SOFR 0x2000 /* b13: SOF frame update interrupt */
-#define DVST 0x1000 /* b12: Device state transition interrupt */
-#define CTRT 0x0800 /* b11: Control transfer stage transition interrupt */
-#define BEMP 0x0400 /* b10: Buffer empty interrupt */
-#define NRDY 0x0200 /* b9: Buffer not ready interrupt */
-#define BRDY 0x0100 /* b8: Buffer ready interrupt */
-#define VBSTS 0x0080 /* b7: VBUS input port */
-#define DVSQ 0x0070 /* b6-4: Device state */
-#define DS_SPD_CNFG 0x0070 /* Suspend Configured */
-#define DS_SPD_ADDR 0x0060 /* Suspend Address */
-#define DS_SPD_DFLT 0x0050 /* Suspend Default */
-#define DS_SPD_POWR 0x0040 /* Suspend Powered */
-#define DS_SUSP 0x0040 /* Suspend */
-#define DS_CNFG 0x0030 /* Configured */
-#define DS_ADDS 0x0020 /* Address */
-#define DS_DFLT 0x0010 /* Default */
-#define DS_POWR 0x0000 /* Powered */
-#define DVSQS 0x0030 /* b5-4: Device state */
-#define VALID 0x0008 /* b3: Setup packet detected flag */
-#define CTSQ 0x0007 /* b2-0: Control transfer stage */
-#define CS_SQER 0x0006 /* Sequence error */
-#define CS_WRND 0x0005 /* Control write nodata status stage */
-#define CS_WRSS 0x0004 /* Control write status stage */
-#define CS_WRDS 0x0003 /* Control write data stage */
-#define CS_RDSS 0x0002 /* Control read status stage */
-#define CS_RDDS 0x0001 /* Control read data stage */
-#define CS_IDST 0x0000 /* Idle or setup stage */
+#define VBINT 0x8000 /* b15: VBUS interrupt */
+#define RESM 0x4000 /* b14: Resume interrupt */
+#define SOFR 0x2000 /* b13: SOF frame update interrupt */
+#define DVST 0x1000 /* b12: Device state transition interrupt */
+#define CTRT 0x0800 /* b11: Control transfer stage transition interrupt */
+#define BEMP 0x0400 /* b10: Buffer empty interrupt */
+#define NRDY 0x0200 /* b9: Buffer not ready interrupt */
+#define BRDY 0x0100 /* b8: Buffer ready interrupt */
+#define VBSTS 0x0080 /* b7: VBUS input port */
+#define DVSQ 0x0070 /* b6-4: Device state */
+#define DS_SPD_CNFG 0x0070 /* Suspend Configured */
+#define DS_SPD_ADDR 0x0060 /* Suspend Address */
+#define DS_SPD_DFLT 0x0050 /* Suspend Default */
+#define DS_SPD_POWR 0x0040 /* Suspend Powered */
+#define DS_SUSP 0x0040 /* Suspend */
+#define DS_CNFG 0x0030 /* Configured */
+#define DS_ADDS 0x0020 /* Address */
+#define DS_DFLT 0x0010 /* Default */
+#define DS_POWR 0x0000 /* Powered */
+#define DVSQS 0x0030 /* b5-4: Device state */
+#define VALID 0x0008 /* b3: Setup packet detected flag */
+#define CTSQ 0x0007 /* b2-0: Control transfer stage */
+#define CS_SQER 0x0006 /* Sequence error */
+#define CS_WRND 0x0005 /* Control write nodata status stage */
+#define CS_WRSS 0x0004 /* Control write status stage */
+#define CS_WRDS 0x0003 /* Control write data stage */
+#define CS_RDSS 0x0002 /* Control read status stage */
+#define CS_RDDS 0x0001 /* Control read data stage */
+#define CS_IDST 0x0000 /* Idle or setup stage */
/* Interrupt Status Register 1 */
-#define OVRCR 0x8000 /* b15: Over-current interrupt */
-#define BCHG 0x4000 /* b14: USB bus chenge interrupt */
-#define DTCH 0x1000 /* b12: Detach sense interrupt */
-#define ATTCH 0x0800 /* b11: Attach sense interrupt */
-#define EOFERR 0x0040 /* b6: EOF-error interrupt */
-#define SIGN 0x0020 /* b5: Setup ignore interrupt */
-#define SACK 0x0010 /* b4: Setup acknowledge interrupt */
+#define OVRCR 0x8000 /* b15: Over-current interrupt */
+#define BCHG 0x4000 /* b14: USB bus chenge interrupt */
+#define DTCH 0x1000 /* b12: Detach sense interrupt */
+#define ATTCH 0x0800 /* b11: Attach sense interrupt */
+#define EOFERR 0x0040 /* b6: EOF-error interrupt */
+#define SIGN 0x0020 /* b5: Setup ignore interrupt */
+#define SACK 0x0010 /* b4: Setup acknowledge interrupt */
/* Frame Number Register */
-#define OVRN 0x8000 /* b15: Overrun error */
-#define CRCE 0x4000 /* b14: Received data error */
-#define FRNM 0x07FF /* b10-0: Frame number */
+#define OVRN 0x8000 /* b15: Overrun error */
+#define CRCE 0x4000 /* b14: Received data error */
+#define FRNM 0x07FF /* b10-0: Frame number */
/* Micro Frame Number Register */
-#define UFRNM 0x0007 /* b2-0: Micro frame number */
+#define UFRNM 0x0007 /* b2-0: Micro frame number */
/* Default Control Pipe Maxpacket Size Register */
/* Pipe Maxpacket Size Register */
-#define DEVSEL 0xF000 /* b15-14: Device address select */
-#define MAXP 0x007F /* b6-0: Maxpacket size of default control pipe */
+#define DEVSEL 0xF000 /* b15-14: Device address select */
+#define MAXP 0x007F /* b6-0: Maxpacket size of default control pipe */
/* Default Control Pipe Control Register */
-#define BSTS 0x8000 /* b15: Buffer status */
-#define SUREQ 0x4000 /* b14: Send USB request */
-#define CSCLR 0x2000 /* b13: complete-split status clear */
-#define CSSTS 0x1000 /* b12: complete-split status */
-#define SUREQCLR 0x0800 /* b11: stop setup request */
-#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */
-#define SQSET 0x0080 /* b7: Sequence toggle bit set */
-#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */
-#define PBUSY 0x0020 /* b5: pipe busy */
-#define PINGE 0x0010 /* b4: ping enable */
-#define CCPL 0x0004 /* b2: Enable control transfer complete */
-#define PID 0x0003 /* b1-0: Response PID */
-#define PID_STALL11 0x0003 /* STALL */
-#define PID_STALL 0x0002 /* STALL */
-#define PID_BUF 0x0001 /* BUF */
-#define PID_NAK 0x0000 /* NAK */
+#define BSTS 0x8000 /* b15: Buffer status */
+#define SUREQ 0x4000 /* b14: Send USB request */
+#define CSCLR 0x2000 /* b13: complete-split status clear */
+#define CSSTS 0x1000 /* b12: complete-split status */
+#define SUREQCLR 0x0800 /* b11: stop setup request */
+#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */
+#define SQSET 0x0080 /* b7: Sequence toggle bit set */
+#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */
+#define PBUSY 0x0020 /* b5: pipe busy */
+#define PINGE 0x0010 /* b4: ping enable */
+#define CCPL 0x0004 /* b2: Enable control transfer complete */
+#define PID 0x0003 /* b1-0: Response PID */
+#define PID_STALL11 0x0003 /* STALL */
+#define PID_STALL 0x0002 /* STALL */
+#define PID_BUF 0x0001 /* BUF */
+#define PID_NAK 0x0000 /* NAK */
/* Pipe Window Select Register */
-#define PIPENM 0x0007 /* b2-0: Pipe select */
+#define PIPENM 0x0007 /* b2-0: Pipe select */
/* Pipe Configuration Register */
-#define R8A66597_TYP 0xC000 /* b15-14: Transfer type */
-#define R8A66597_ISO 0xC000 /* Isochronous */
-#define R8A66597_INT 0x8000 /* Interrupt */
-#define R8A66597_BULK 0x4000 /* Bulk */
-#define R8A66597_BFRE 0x0400 /* b10: Buffer ready interrupt mode select */
-#define R8A66597_DBLB 0x0200 /* b9: Double buffer mode select */
-#define R8A66597_CNTMD 0x0100 /* b8: Continuous transfer mode select */
-#define R8A66597_SHTNAK 0x0080 /* b7: Transfer end NAK */
-#define R8A66597_DIR 0x0010 /* b4: Transfer direction select */
-#define R8A66597_EPNUM 0x000F /* b3-0: Eendpoint number select */
+#define R8A66597_TYP 0xC000 /* b15-14: Transfer type */
+#define R8A66597_ISO 0xC000 /* Isochronous */
+#define R8A66597_INT 0x8000 /* Interrupt */
+#define R8A66597_BULK 0x4000 /* Bulk */
+#define R8A66597_BFRE 0x0400 /* b10: Buffer ready interrupt mode select */
+#define R8A66597_DBLB 0x0200 /* b9: Double buffer mode select */
+#define R8A66597_CNTMD 0x0100 /* b8: Continuous transfer mode select */
+#define R8A66597_SHTNAK 0x0080 /* b7: Transfer end NAK */
+#define R8A66597_DIR 0x0010 /* b4: Transfer direction select */
+#define R8A66597_EPNUM 0x000F /* b3-0: Eendpoint number select */
/* Pipe Buffer Configuration Register */
-#define BUFSIZE 0x7C00 /* b14-10: Pipe buffer size */
-#define BUFNMB 0x007F /* b6-0: Pipe buffer number */
-#define PIPE0BUF 256
-#define PIPExBUF 64
+#define BUFSIZE 0x7C00 /* b14-10: Pipe buffer size */
+#define BUFNMB 0x007F /* b6-0: Pipe buffer number */
+#define PIPE0BUF 256
+#define PIPExBUF 64
/* Pipe Maxpacket Size Register */
-#define MXPS 0x07FF /* b10-0: Maxpacket size */
+#define MXPS 0x07FF /* b10-0: Maxpacket size */
/* Pipe Cycle Configuration Register */
-#define IFIS 0x1000 /* b12: Isochronous in-buffer flush mode select */
-#define IITV 0x0007 /* b2-0: Isochronous interval */
+#define IFIS 0x1000 /* b12: Isochronous in-buffer flush mode select */
+#define IITV 0x0007 /* b2-0: Isochronous interval */
/* Pipex Control Register */
-#define BSTS 0x8000 /* b15: Buffer status */
-#define INBUFM 0x4000 /* b14: IN buffer monitor (Only for PIPE1 to 5) */
-#define CSCLR 0x2000 /* b13: complete-split status clear */
-#define CSSTS 0x1000 /* b12: complete-split status */
-#define ATREPM 0x0400 /* b10: Auto repeat mode */
-#define ACLRM 0x0200 /* b9: Out buffer auto clear mode */
-#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */
-#define SQSET 0x0080 /* b7: Sequence toggle bit set */
-#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */
-#define PBUSY 0x0020 /* b5: pipe busy */
-#define PID 0x0003 /* b1-0: Response PID */
+#define BSTS 0x8000 /* b15: Buffer status */
+#define INBUFM 0x4000 /* b14: IN buffer monitor (Only for PIPE1 to 5) */
+#define CSCLR 0x2000 /* b13: complete-split status clear */
+#define CSSTS 0x1000 /* b12: complete-split status */
+#define ATREPM 0x0400 /* b10: Auto repeat mode */
+#define ACLRM 0x0200 /* b9: Out buffer auto clear mode */
+#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */
+#define SQSET 0x0080 /* b7: Sequence toggle bit set */
+#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */
+#define PBUSY 0x0020 /* b5: pipe busy */
+#define PID 0x0003 /* b1-0: Response PID */
/* PIPExTRE */
-#define TRENB 0x0200 /* b9: Transaction counter enable */
-#define TRCLR 0x0100 /* b8: Transaction counter clear */
+#define TRENB 0x0200 /* b9: Transaction counter enable */
+#define TRCLR 0x0100 /* b8: Transaction counter clear */
/* PIPExTRN */
-#define TRNCNT 0xFFFF /* b15-0: Transaction counter */
+#define TRNCNT 0xFFFF /* b15-0: Transaction counter */
/* DEVADDx */
-#define UPPHUB 0x7800
-#define HUBPORT 0x0700
-#define USBSPD 0x00C0
-#define RTPORT 0x0001
+#define UPPHUB 0x7800
+#define HUBPORT 0x0700
+#define USBSPD 0x00C0
+#define RTPORT 0x0001
/* Suspend Mode Register */
-#define SUSPM 0x4000 /* b14: Suspend */
+#define SUSPM 0x4000 /* b14: Suspend */
#define R8A66597_MAX_NUM_PIPE 10
#define R8A66597_BUF_BSIZE 8
#define R8A66597_MAX_DEVICE 10
-#if defined(CONFIG_SUPERH_ON_CHIP_R8A66597)
-#define R8A66597_MAX_ROOT_HUB 1
-#else
#define R8A66597_MAX_ROOT_HUB 2
-#endif
#define R8A66597_MAX_SAMPLING 5
#define R8A66597_RH_POLL_TIME 10
#define BULK_OUT_PIPENUM 4
#define BULK_OUT_BUFNUM 40
-#define check_bulk_or_isoc(pipenum) ((pipenum >= 1 && pipenum <= 5))
-#define check_interrupt(pipenum) ((pipenum >= 6 && pipenum <= 9))
-#define make_devsel(addr) (addr << 12)
+#define make_devsel(addr) ((addr) << 12)
struct r8a66597 {
unsigned long reg;
unsigned short port_change;
u16 speed; /* HSMODE or FSMODE or LSMODE */
unsigned char rh_devnum;
+ struct udevice *vbus_supply;
};
static inline u16 r8a66597_read(struct r8a66597 *r8a66597, unsigned long offset)
{
- return inw(r8a66597->reg + offset);
+ return readw(r8a66597->reg + offset);
}
static inline void r8a66597_read_fifo(struct r8a66597 *r8a66597,
int len)
{
int i;
-#if defined(CONFIG_SUPERH_ON_CHIP_R8A66597) || defined(CONFIG_RZA_USB)
unsigned long fifoaddr = r8a66597->reg + offset;
unsigned long count;
unsigned long *p = buf;
count = len / 4;
for (i = 0; i < count; i++)
- p[i] = inl(r8a66597->reg + offset);
+ p[i] = readl(r8a66597->reg + offset);
if (len & 0x00000003) {
- unsigned long tmp = inl(fifoaddr);
+ unsigned long tmp = readl(fifoaddr);
+
memcpy((unsigned char *)buf + count * 4, &tmp, len & 0x03);
}
-#else
- unsigned short *p = buf;
-
- len = (len + 1) / 2;
- for (i = 0; i < len; i++)
- p[i] = inw(r8a66597->reg + offset);
-#endif
}
static inline void r8a66597_write(struct r8a66597 *r8a66597, u16 val,
unsigned long offset)
{
- outw(val, r8a66597->reg + offset);
+ writew(val, r8a66597->reg + offset);
}
static inline void r8a66597_write_fifo(struct r8a66597 *r8a66597,
{
int i;
unsigned long fifoaddr = r8a66597->reg + offset;
-#if defined(CONFIG_SUPERH_ON_CHIP_R8A66597) || defined(CONFIG_RZA_USB)
unsigned long count;
unsigned char *pb;
unsigned long *p = buf;
count = len / 4;
for (i = 0; i < count; i++)
- outl(p[i], fifoaddr);
+ writel(p[i], fifoaddr);
if (len & 0x00000003) {
pb = (unsigned char *)buf + count * 4;
for (i = 0; i < (len & 0x00000003); i++) {
if (r8a66597_read(r8a66597, CFIFOSEL) & BIGEND)
- outb(pb[i], fifoaddr + i);
+ writeb(pb[i], fifoaddr + i);
else
- outb(pb[i], fifoaddr + 3 - i);
+ writeb(pb[i], fifoaddr + 3 - i);
}
}
-#else
- int odd = len & 0x0001;
- unsigned short *p = buf;
-
- len = len / 2;
- for (i = 0; i < len; i++)
- outw(p[i], fifoaddr);
-
- if (odd) {
- unsigned char *pb = (unsigned char *)(buf + len);
- outb(*pb, fifoaddr);
- }
-#endif
}
static inline void r8a66597_mdfy(struct r8a66597 *r8a66597,
u16 val, u16 pat, unsigned long offset)
{
u16 tmp;
+
tmp = r8a66597_read(r8a66597, offset);
tmp = tmp & (~pat);
tmp = tmp | val;
#define get_pipetrn_addr(pipenum) (PIPE1TRN + (pipenum - 1) * 4)
#define get_devadd_addr(address) (DEVADD0 + address * 2)
-
/* USB HUB CONSTANTS (not OHCI-specific; see hub.h, based on usb_ohci.h) */
/* destination of request */
/* roothub.a masks */
#define RH_A_NDP (0xff << 0) /* number of downstream ports */
-#define RH_A_PSM (1 << 8) /* power switching mode */
-#define RH_A_NPS (1 << 9) /* no power switching */
-#define RH_A_DT (1 << 10) /* device type (mbz) */
-#define RH_A_OCPM (1 << 11) /* over current protection mode */
-#define RH_A_NOCP (1 << 12) /* no over current protection */
+#define RH_A_PSM BIT(8) /* power switching mode */
+#define RH_A_NPS BIT(9) /* no power switching */
+#define RH_A_DT BIT(10) /* device type (mbz) */
+#define RH_A_OCPM BIT(11) /* over current protection mode */
+#define RH_A_NOCP BIT(12) /* no over current protection */
#define RH_A_POTPGT (0xff << 24) /* power on to power good time */
#endif /* __R8A66597_H__ */
projects / oweals / u-boot.git / commitdiff