powerpc/b4860qds: Added Support for B4860QDS
authorYork Sun <yorksun@freescale.com>
Sun, 23 Dec 2012 19:25:27 +0000 (19:25 +0000)
committerAndy Fleming <afleming@freescale.com>
Wed, 30 Jan 2013 17:25:11 +0000 (11:25 -0600)
B4860QDS is a high-performance computing evaluation, development and
test platform supporting the B4860 QorIQ Power Architecture processor.

B4860QDS Overview
------------------
- DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,
  ECC, 4 GB of memory in two ranks of 2 GB.
- DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s,  ECC, 2 GB of memory. Single rank.
- SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point
  16x16 switch VSC3316
- SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point
  8x8 switch VSC3308
- USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode.
- B4860 UART port is available over USB-to-UART translator USB2SER or over
  RS232 flat cable.
- A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper
  connectors for Stand-alone mode and to the 1000Base-X over AMC MicroTCA
  connector ports 0 and 2 for AMC mode.
- The B4860 configuration may be loaded from nine bits coded reset
  configuration reset source. The RCW source is set by appropriate
  DIP-switches:
- 16-bit NOR Flash / PROMJet
- QIXIS 8-bit NOR Flash Emulator
- 8-bit NAND Flash
- 24-bit SPI Flash
- Long address I2C EEPROM
- Available debug interfaces are:
- On-board eCWTAP controller with ETH and USB I/F
- JTAG/COP 16-pin header for any external TAP controller
- External JTAG source over AMC to support B2B configuration
- 70-pin Aurora debug connector
- QIXIS (FPGA) logic:
- 2 KB internal memory space including
- IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK,
  DDRCLK1, 2 and RTCCLK.
- Two 8T49N222A SerDes ref clock devices support two SerDes port clocks
  - total four refclk, including CPRI clock scheme

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
13 files changed:
board/freescale/b4860qds/Makefile [new file with mode: 0644]
board/freescale/b4860qds/b4860qds.c [new file with mode: 0644]
board/freescale/b4860qds/b4860qds.h [new file with mode: 0644]
board/freescale/b4860qds/b4860qds_crossbar_con.h [new file with mode: 0644]
board/freescale/b4860qds/b4860qds_qixis.h [new file with mode: 0644]
board/freescale/b4860qds/ddr.c [new file with mode: 0644]
board/freescale/b4860qds/eth_b4860qds.c [new file with mode: 0644]
board/freescale/b4860qds/law.c [new file with mode: 0644]
board/freescale/b4860qds/pci.c [new file with mode: 0644]
board/freescale/b4860qds/tlb.c [new file with mode: 0644]
boards.cfg
doc/README.b4860qds [new file with mode: 0644]
include/configs/B4860QDS.h [new file with mode: 0644]

diff --git a/board/freescale/b4860qds/Makefile b/board/freescale/b4860qds/Makefile
new file mode 100644 (file)
index 0000000..06018f4
--- /dev/null
@@ -0,0 +1,54 @@
+#
+# Copyright 2012 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB    = $(obj)lib$(BOARD).o
+
+COBJS-y        += $(BOARD).o
+COBJS-y        += ddr.o
+COBJS-$(CONFIG_B4860QDS)+= eth_b4860qds.o
+COBJS-$(CONFIG_PCI)    += pci.o
+COBJS-y        += law.o
+COBJS-y        += tlb.o
+
+SRCS   := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS   := $(addprefix $(obj),$(COBJS-y))
+SOBJS  := $(addprefix $(obj),$(SOBJS))
+
+$(LIB):        $(obj).depend $(OBJS) $(SOBJS)
+       $(call cmd_link_o_target, $(OBJS))
+
+clean:
+       rm -f $(OBJS) $(SOBJS)
+
+distclean:     clean
+       rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c
new file mode 100644 (file)
index 0000000..88bdc1f
--- /dev/null
@@ -0,0 +1,458 @@
+/*
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <fm_eth.h>
+
+#include "../common/qixis.h"
+#include "../common/vsc3316_3308.h"
+#include "b4860qds.h"
+#include "b4860qds_qixis.h"
+#include "b4860qds_crossbar_con.h"
+
+#define CLK_MUX_SEL_MASK       0x4
+#define ETH_PHY_CLK_OUT                0x4
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+       char buf[64];
+       u8 sw;
+       struct cpu_type *cpu = gd->cpu;
+       ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+       unsigned int i;
+       static const char *const freq[] = {"100", "125", "156.25", "161.13",
+                                               "122.88", "122.88", "122.88"};
+       int clock;
+
+       printf("Board: %sQDS, ", cpu->name);
+       printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, ",
+               QIXIS_READ(id), QIXIS_READ(arch));
+
+       sw = QIXIS_READ(brdcfg[0]);
+       sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
+
+       if (sw < 0x8)
+               printf("vBank: %d\n", sw);
+       else if (sw >= 0x8 && sw <= 0xE)
+               puts("NAND\n");
+       else
+               printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
+
+       printf("FPGA: v%d (%s), build %d",
+               (int)QIXIS_READ(scver), qixis_read_tag(buf),
+               (int)qixis_read_minor());
+       /* the timestamp string contains "\n" at the end */
+       printf(" on %s", qixis_read_time(buf));
+
+       /* Display the RCW, so that no one gets confused as to what RCW
+        * we're actually using for this boot.
+        */
+       puts("Reset Configuration Word (RCW):");
+       for (i = 0; i < ARRAY_SIZE(gur->rcwsr); i++) {
+               u32 rcw = in_be32(&gur->rcwsr[i]);
+
+               if ((i % 4) == 0)
+                       printf("\n       %08x:", i * 4);
+               printf(" %08x", rcw);
+       }
+       puts("\n");
+
+       /*
+        * Display the actual SERDES reference clocks as configured by the
+        * dip switches on the board.  Note that the SWx registers could
+        * technically be set to force the reference clocks to match the
+        * values that the SERDES expects (or vice versa).  For now, however,
+        * we just display both values and hope the user notices when they
+        * don't match.
+        */
+       puts("SERDES Reference Clocks: ");
+       sw = QIXIS_READ(brdcfg[2]);
+       clock = (sw >> 5) & 7;
+       printf("Bank1=%sMHz ", freq[clock]);
+       sw = QIXIS_READ(brdcfg[4]);
+       clock = (sw >> 6) & 3;
+       printf("Bank2=%sMHz\n", freq[clock]);
+
+       return 0;
+}
+
+int select_i2c_ch_pca(u8 ch)
+{
+       int ret;
+
+       /* Selecting proper channel via PCA*/
+       ret = i2c_write(I2C_MUX_PCA_ADDR, 0x0, 1, &ch, 1);
+       if (ret) {
+               printf("PCA: failed to select proper channel.\n");
+               return ret;
+       }
+
+       return 0;
+}
+
+int configure_vsc3316_3308(void)
+{
+       ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+       unsigned int num_vsc16_con, num_vsc08_con;
+       u32 serdes1_prtcl, serdes2_prtcl;
+       int ret;
+
+       serdes1_prtcl = in_be32(&gur->rcwsr[4]) &
+                       FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+       if (!serdes1_prtcl) {
+               printf("SERDES1 is not enabled\n");
+               return 0;
+       }
+       serdes1_prtcl >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+       debug("Using SERDES1 Protocol: 0x%x:\n", serdes1_prtcl);
+
+       serdes2_prtcl = in_be32(&gur->rcwsr[4]) &
+                       FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
+       if (!serdes2_prtcl) {
+               printf("SERDES2 is not enabled\n");
+               return 0;
+       }
+       serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
+       debug("Using SERDES2 Protocol: 0x%x:\n", serdes2_prtcl);
+
+       switch (serdes1_prtcl) {
+       case 0x2a:
+       case 0x2C:
+       case 0x2D:
+       case 0x2E:
+                       /*
+                        * Configuration:
+                        * SERDES: 1
+                        * Lanes: A,B: SGMII
+                        * Lanes: C,D,E,F,G,H: CPRI
+                        */
+               debug("Configuring crossbar to use onboard SGMII PHYs:"
+                               "srds_prctl:%x\n", serdes1_prtcl);
+               num_vsc16_con = NUM_CON_VSC3316;
+               /* Configure VSC3316 crossbar switch */
+               ret = select_i2c_ch_pca(I2C_CH_VSC3316);
+               if (!ret) {
+                       ret = vsc3316_config(VSC3316_TX_ADDRESS,
+                                       vsc16_tx_sgmii_lane_ab, num_vsc16_con);
+                       if (ret)
+                               return ret;
+                       ret = vsc3316_config(VSC3316_RX_ADDRESS,
+                                       vsc16_rx_sgmii_lane_ab, num_vsc16_con);
+                       if (ret)
+                               return ret;
+               } else {
+                       return ret;
+               }
+               break;
+
+#ifdef CONFIG_PPC_B4420
+       case 0x18:
+                       /*
+                        * Configuration:
+                        * SERDES: 1
+                        * Lanes: A,B,C,D: SGMII
+                        * Lanes: E,F,G,H: CPRI
+                        */
+               debug("Configuring crossbar to use onboard SGMII PHYs:"
+                               "srds_prctl:%x\n", serdes1_prtcl);
+               num_vsc16_con = NUM_CON_VSC3316;
+               /* Configure VSC3316 crossbar switch */
+               ret = select_i2c_ch_pca(I2C_CH_VSC3316);
+               if (!ret) {
+                       ret = vsc3316_config(VSC3316_TX_ADDRESS,
+                                       vsc16_tx_sgmii_lane_cd, num_vsc16_con);
+                       if (ret)
+                               return ret;
+                       ret = vsc3316_config(VSC3316_RX_ADDRESS,
+                                       vsc16_rx_sgmii_lane_cd, num_vsc16_con);
+                       if (ret)
+                               return ret;
+               } else {
+                       return ret;
+               }
+               break;
+#endif
+
+       case 0x3E:
+       case 0x0D:
+       case 0x0E:
+       case 0x12:
+               num_vsc16_con = NUM_CON_VSC3316;
+               /* Configure VSC3316 crossbar switch */
+               ret = select_i2c_ch_pca(I2C_CH_VSC3316);
+               if (!ret) {
+                       ret = vsc3316_config(VSC3316_TX_ADDRESS,
+                                       vsc16_tx_sfp, num_vsc16_con);
+                       if (ret)
+                               return ret;
+                       ret = vsc3316_config(VSC3316_RX_ADDRESS,
+                                       vsc16_rx_sfp, num_vsc16_con);
+                       if (ret)
+                               return ret;
+               } else {
+                       return ret;
+               }
+               break;
+       default:
+               printf("WARNING:VSC crossbars programming not supported for:%x"
+                                       " SerDes1 Protocol.\n", serdes1_prtcl);
+               return -1;
+       }
+
+       switch (serdes2_prtcl) {
+       case 0x9E:
+       case 0x9A:
+       case 0x98:
+       case 0xb2:
+       case 0x49:
+       case 0x4E:
+       case 0x8D:
+       case 0x7A:
+               num_vsc08_con = NUM_CON_VSC3308;
+               /* Configure VSC3308 crossbar switch */
+               ret = select_i2c_ch_pca(I2C_CH_VSC3308);
+               if (!ret) {
+                       ret = vsc3308_config(VSC3308_TX_ADDRESS,
+                                       vsc08_tx_amc, num_vsc08_con);
+                       if (ret)
+                               return ret;
+                       ret = vsc3308_config(VSC3308_RX_ADDRESS,
+                                       vsc08_rx_amc, num_vsc08_con);
+                       if (ret)
+                               return ret;
+               } else {
+                       return ret;
+               }
+               break;
+       default:
+               printf("WARNING:VSC crossbars programming not supported for: %x"
+                                       " SerDes2 Protocol.\n", serdes2_prtcl);
+               return -1;
+       }
+
+       return 0;
+}
+
+int board_early_init_r(void)
+{
+       const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+       const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+       /*
+        * Remap Boot flash + PROMJET region to caching-inhibited
+        * so that flash can be erased properly.
+        */
+
+       /* Flush d-cache and invalidate i-cache of any FLASH data */
+       flush_dcache();
+       invalidate_icache();
+
+       /* invalidate existing TLB entry for flash + promjet */
+       disable_tlb(flash_esel);
+
+       set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+                       MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+                       0, flash_esel, BOOKE_PAGESZ_256M, 1);
+
+       set_liodns();
+#ifdef CONFIG_SYS_DPAA_QBMAN
+       setup_portals();
+#endif
+
+       /* Configure VSC3316 and VSC3308 crossbar switches */
+       if (configure_vsc3316_3308())
+               printf("VSC:failed to configure VSC3316/3308.\n");
+       else
+               printf("VSC:VSC3316/3308 successfully configured.\n");
+
+       select_i2c_ch_pca(I2C_CH_DEFAULT);
+
+       return 0;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+       u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+
+       switch ((sysclk_conf & 0x0C) >> 2) {
+       case QIXIS_CLK_100:
+               return 100000000;
+       case QIXIS_CLK_125:
+               return 125000000;
+       case QIXIS_CLK_133:
+               return 133333333;
+       }
+       return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+       u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+
+       switch (ddrclk_conf & 0x03) {
+       case QIXIS_CLK_100:
+               return 100000000;
+       case QIXIS_CLK_125:
+               return 125000000;
+       case QIXIS_CLK_133:
+               return 133333333;
+       }
+       return 66666666;
+}
+
+static int serdes_refclock(u8 sw, u8 sdclk)
+{
+       unsigned int clock;
+       int ret = -1;
+       u8 brdcfg4;
+
+       if (sdclk == 1) {
+               brdcfg4 = QIXIS_READ(brdcfg[4]);
+               if ((brdcfg4 & CLK_MUX_SEL_MASK) == ETH_PHY_CLK_OUT)
+                       return SRDS_PLLCR0_RFCK_SEL_125;
+               else
+                       clock = (sw >> 5) & 7;
+       } else
+               clock = (sw >> 6) & 3;
+
+       switch (clock) {
+       case 0:
+               ret = SRDS_PLLCR0_RFCK_SEL_100;
+               break;
+       case 1:
+               ret = SRDS_PLLCR0_RFCK_SEL_125;
+               break;
+       case 2:
+               ret = SRDS_PLLCR0_RFCK_SEL_156_25;
+               break;
+       case 3:
+               ret = SRDS_PLLCR0_RFCK_SEL_161_13;
+               break;
+       case 4:
+       case 5:
+       case 6:
+               ret = SRDS_PLLCR0_RFCK_SEL_122_88;
+               break;
+       default:
+               ret = -1;
+               break;
+       }
+
+       return ret;
+}
+
+static const char *serdes_clock_to_string(u32 clock)
+{
+       switch (clock) {
+       case SRDS_PLLCR0_RFCK_SEL_100:
+               return "100";
+       case SRDS_PLLCR0_RFCK_SEL_125:
+               return "125";
+       case SRDS_PLLCR0_RFCK_SEL_156_25:
+               return "156.25";
+       case SRDS_PLLCR0_RFCK_SEL_161_13:
+               return "161.13";
+       default:
+               return "122.88";
+       }
+}
+
+#define NUM_SRDS_BANKS 2
+
+int misc_init_r(void)
+{
+       u8 sw;
+       serdes_corenet_t *srds_regs =
+               (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR;
+       u32 actual[NUM_SRDS_BANKS];
+       unsigned int i;
+       int clock;
+
+       sw = QIXIS_READ(brdcfg[2]);
+       clock = serdes_refclock(sw, 1);
+       if (clock >= 0)
+               actual[0] = clock;
+       else
+               printf("Warning: SDREFCLK1 switch setting is unsupported\n");
+
+       sw = QIXIS_READ(brdcfg[4]);
+       clock = serdes_refclock(sw, 2);
+       if (clock >= 0)
+               actual[1] = clock;
+       else
+               printf("Warning: SDREFCLK2 switch setting unsupported\n");
+
+       for (i = 0; i < NUM_SRDS_BANKS; i++) {
+               u32 pllcr0 = srds_regs->bank[i].pllcr0;
+               u32 expected = pllcr0 & SRDS_PLLCR0_RFCK_SEL_MASK;
+               if (expected != actual[i]) {
+                       printf("Warning: SERDES bank %u expects reference clock"
+                              " %sMHz, but actual is %sMHz\n", i + 1,
+                              serdes_clock_to_string(expected),
+                              serdes_clock_to_string(actual[i]));
+               }
+       }
+
+       return 0;
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+       phys_addr_t base;
+       phys_size_t size;
+
+       ft_cpu_setup(blob, bd);
+
+       base = getenv_bootm_low();
+       size = getenv_bootm_size();
+
+       fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+       pci_of_setup(blob, bd);
+#endif
+
+       fdt_fixup_liodn(blob);
+
+#ifdef CONFIG_HAS_FSL_DR_USB
+       fdt_fixup_dr_usb(blob, bd);
+#endif
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+       fdt_fixup_fman_ethernet(blob);
+       fdt_fixup_board_enet(blob);
+#endif
+}
diff --git a/board/freescale/b4860qds/b4860qds.h b/board/freescale/b4860qds/b4860qds.h
new file mode 100644 (file)
index 0000000..f290f3c
--- /dev/null
@@ -0,0 +1,26 @@
+/*
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CORENET_DS_H__
+#define __CORENET_DS_H__
+
+void fdt_fixup_board_enet(void *blob);
+void pci_of_setup(void *blob, bd_t *bd);
+
+#endif
diff --git a/board/freescale/b4860qds/b4860qds_crossbar_con.h b/board/freescale/b4860qds/b4860qds_crossbar_con.h
new file mode 100644 (file)
index 0000000..994dec5
--- /dev/null
@@ -0,0 +1,67 @@
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CROSSBAR_CONNECTIONS_H__
+#define __CROSSBAR_CONNECTIONS_H__
+
+#define NUM_CON_VSC3316        8
+#define NUM_CON_VSC3308        4
+
+static const int8_t vsc16_tx_amc[8][2] = { {15, 3}, {0, 2}, {7, 4}, {9, 10},
+                               {5, 11}, {4, 5}, {2, 6}, {12, 9} };
+
+static const int8_t vsc16_tx_sfp[8][2] = { {15, 8}, {0, 0}, {7, 7}, {9, 1},
+                               {5, 15}, {4, 14}, {2, 12}, {12, 13} };
+
+static const int8_t vsc16_tx_sgmii_lane_ab[8][2] = { {2, 14}, {12, 15},
+               {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
+
+#ifdef CONFIG_PPC_B4420
+static const int8_t vsc16_tx_sgmii_lane_cd[8][2] = { {5, 14}, {4, 15},
+               {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
+#endif
+static const int8_t vsc16_tx_aurora[8][2] = { {2, 13}, {12, 12}, {-1, -1},
+                       {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
+
+static const int8_t vsc16_rx_amc[8][2] = { {3, 15}, {2, 1}, {4, 8}, {10, 9},
+                               {11, 11}, {5, 10}, {6, 3}, {9, 12} };
+
+static const int8_t vsc16_rx_sfp[8][2] = { {0, 15}, {8, 1}, {1, 8}, {7, 9},
+                               {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
+
+static const int8_t vsc16_rx_sgmii_lane_ab[8][2] = { {14, 3}, {15, 12},
+               {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
+
+#ifdef CONFIG_PPC_B4420
+static const int8_t vsc16_rx_sgmii_lane_cd[8][2] = { {14, 11}, {15, 10},
+               {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
+#endif
+
+static const int8_t vsc16_rx_aurora[8][2] = { {12, 3}, {13, 12}, {-1, -1},
+                       {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1}, {-1, -1} };
+
+static const int8_t vsc08_tx_amc[4][2] = { {2, 2}, {3, 3}, {7, 4}, {1, 5} };
+
+static const int8_t vsc08_tx_sfp[4][2] = { {2, 6}, {3, 7}, {7, 1}, {1, 0} };
+
+static const int8_t vsc08_rx_amc[4][2] = { {2, 3}, {3, 4}, {4, 7}, {5, 1} };
+
+static const int8_t vsc08_rx_sfp[4][2] = { {6, 3}, {7, 4}, {1, 7}, {0, 1} };
+
+#endif
diff --git a/board/freescale/b4860qds/b4860qds_qixis.h b/board/freescale/b4860qds/b4860qds_qixis.h
new file mode 100644 (file)
index 0000000..575b2ae
--- /dev/null
@@ -0,0 +1,37 @@
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __B4860QDS_QIXIS_H__
+#define __B4860QDS_QIXIS_H__
+
+/* Definitions of QIXIS Registers for B4860QDS */
+
+/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */
+#define BRDCFG4_EMISEL_MASK            0xE0
+#define BRDCFG4_EMISEL_SHIFT           5
+
+/* CLK */
+#define QIXIS_CLK_66           0x0
+#define QIXIS_CLK_100          0x1
+#define QIXIS_CLK_125          0x2
+#define QIXIS_CLK_133          0x3
+
+#define QIXIS_SRDS1CLK_122             0x5a
+#define QIXIS_SRDS1CLK_125             0x5e
+#endif
diff --git a/board/freescale/b4860qds/ddr.c b/board/freescale/b4860qds/ddr.c
new file mode 100644 (file)
index 0000000..dd4c0f6
--- /dev/null
@@ -0,0 +1,190 @@
+/*
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 or later as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+dimm_params_t ddr_raw_timing = {
+       .n_ranks = 2,
+       .rank_density = 2147483648u,
+       .capacity = 4294967296u,
+       .primary_sdram_width = 64,
+       .ec_sdram_width = 8,
+       .registered_dimm = 0,
+       .mirrored_dimm = 1,
+       .n_row_addr = 15,
+       .n_col_addr = 10,
+       .n_banks_per_sdram_device = 8,
+       .edc_config = 2,        /* ECC */
+       .burst_lengths_bitmask = 0x0c,
+
+       .tCKmin_X_ps = 1071,
+       .caslat_X = 0x2fe << 4, /* 5,6,7,8,9,10,11,13 */
+       .tAA_ps = 13910,
+       .tWR_ps = 15000,
+       .tRCD_ps = 13910,
+       .tRRD_ps = 6000,
+       .tRP_ps = 13910,
+       .tRAS_ps = 34000,
+       .tRC_ps = 48910,
+       .tRFC_ps = 260000,
+       .tWTR_ps = 7500,
+       .tRTP_ps = 7500,
+       .refresh_rate_ps = 7800000,
+       .tFAW_ps = 35000,
+};
+
+int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
+               unsigned int controller_number,
+               unsigned int dimm_number)
+{
+       const char dimm_model[] = "RAW timing DDR";
+
+       if ((controller_number == 0) && (dimm_number == 0)) {
+               memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
+               memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
+               memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
+       }
+
+       return 0;
+}
+
+struct board_specific_parameters {
+       u32 n_ranks;
+       u32 datarate_mhz_high;
+       u32 clk_adjust;
+       u32 wrlvl_start;
+       u32 wrlvl_ctl_2;
+       u32 wrlvl_ctl_3;
+       u32 cpo;
+       u32 write_data_delay;
+       u32 force_2T;
+};
+
+/*
+ * This table contains all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+static const struct board_specific_parameters udimm0[] = {
+       /*
+        * memory controller 0
+        *   num|  hi|  clk| wrlvl |   wrlvl   |  wrlvl | cpo  |wrdata|2T
+        * ranks| mhz|adjst| start |   ctl2    |  ctl3  |      |delay |
+        */
+       {2,  1350,    4,     7, 0x09080807, 0x07060607,   0xff,    2,  0},
+       {2,  1666,    4,     7, 0x09080806, 0x06050607,   0xff,    2,  0},
+       {2,  1900,    3,     7, 0x08070706, 0x06040507,   0xff,    2,  0},
+       {1,  1350,    4,     7, 0x09080807, 0x07060607,   0xff,    2,  0},
+       {1,  1700,    4,     7, 0x09080806, 0x06050607,   0xff,    2,  0},
+       {1,  1900,    3,     7, 0x08070706, 0x06040507,   0xff,    2,  0},
+       {}
+};
+
+static const struct board_specific_parameters *udimms[] = {
+       udimm0,
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+                               dimm_params_t *pdimm,
+                               unsigned int ctrl_num)
+{
+       const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+       ulong ddr_freq;
+
+       if (ctrl_num > 2) {
+               printf("Not supported controller number %d\n", ctrl_num);
+               return;
+       }
+       if (!pdimm->n_ranks)
+               return;
+
+       pbsp = udimms[0];
+
+
+       /* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+        * freqency and n_banks specified in board_specific_parameters table.
+        */
+       ddr_freq = get_ddr_freq(0) / 1000000;
+       while (pbsp->datarate_mhz_high) {
+               if (pbsp->n_ranks == pdimm->n_ranks) {
+                       if (ddr_freq <= pbsp->datarate_mhz_high) {
+                               popts->cpo_override = pbsp->cpo;
+                               popts->write_data_delay =
+                                       pbsp->write_data_delay;
+                               popts->clk_adjust = pbsp->clk_adjust;
+                               popts->wrlvl_start = pbsp->wrlvl_start;
+                               popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+                               popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+                               popts->twoT_en = pbsp->force_2T;
+                               goto found;
+                       }
+                       pbsp_highest = pbsp;
+               }
+               pbsp++;
+       }
+
+       if (pbsp_highest) {
+               printf("Error: board specific timing not found "
+                       "for data rate %lu MT/s\n"
+                       "Trying to use the highest speed (%u) parameters\n",
+                       ddr_freq, pbsp_highest->datarate_mhz_high);
+               popts->cpo_override = pbsp_highest->cpo;
+               popts->write_data_delay = pbsp_highest->write_data_delay;
+               popts->clk_adjust = pbsp_highest->clk_adjust;
+               popts->wrlvl_start = pbsp_highest->wrlvl_start;
+               popts->twoT_en = pbsp_highest->force_2T;
+       } else {
+               panic("DIMM is not supported by this board");
+       }
+found:
+       /*
+        * Factors to consider for half-strength driver enable:
+        *      - number of DIMMs installed
+        */
+       popts->half_strength_driver_enable = 0;
+       /*
+        * Write leveling override
+        */
+       popts->wrlvl_override = 1;
+       popts->wrlvl_sample = 0xf;
+
+       /*
+        * Rtt and Rtt_WR override
+        */
+       popts->rtt_override = 0;
+
+       /* Enable ZQ calibration */
+       popts->zq_en = 1;
+
+       /* DHC_EN =1, ODT = 75 Ohm */
+       popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+       popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+}
+
+phys_size_t initdram(int board_type)
+{
+       phys_size_t dram_size;
+
+       puts("Initializing....using SPD\n");
+
+       dram_size = fsl_ddr_sdram();
+
+       dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+       dram_size *= 0x100000;
+
+       puts("    DDR: ");
+       return dram_size;
+}
diff --git a/board/freescale/b4860qds/eth_b4860qds.c b/board/freescale/b4860qds/eth_b4860qds.c
new file mode 100644 (file)
index 0000000..68e2725
--- /dev/null
@@ -0,0 +1,338 @@
+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Author: Sandeep Kumar Singh <sandeep@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* This file is based on board/freescale/corenet_ds/eth_superhydra.c */
+
+/*
+ * This file handles the board muxing between the Fman Ethernet MACs and
+ * the RGMII/SGMII/XGMII PHYs on a Freescale B4860 "Centaur". The SGMII
+ * PHYs are the two on-board 1Gb ports. There are no RGMII PHY on board.
+ * The 10Gb XGMII PHY is provided via the XAUI riser card. There is only
+ * one Fman device on B4860. The SERDES configuration is used to determine
+ * where the SGMII and XAUI cards exist, and also which Fman MACs are routed
+ * to which PHYs. So for a given Fman MAC, there is one and only PHY it
+ * connects to. MACs cannot be routed to PHYs dynamically. This configuration
+ * is done at boot time by reading SERDES protocol from RCW.
+ */
+
+#include <common.h>
+#include <netdev.h>
+#include <asm/fsl_serdes.h>
+#include <fm_eth.h>
+#include <fsl_mdio.h>
+#include <malloc.h>
+#include <fdt_support.h>
+#include <asm/fsl_dtsec.h>
+
+#include "../common/ngpixis.h"
+#include "../common/fman.h"
+#include "../common/qixis.h"
+#include "b4860qds_qixis.h"
+
+#define EMI_NONE       0xFFFFFFFF
+
+#ifdef CONFIG_FMAN_ENET
+
+/*
+ * Mapping of all 16 SERDES lanes to board slots. A value n(>0) will mean that
+ * lane at index is mapped to slot number n. A value of '0' will mean
+ * that the mapping must be determined dynamically, or that the lane maps to
+ * something other than a board slot
+ */
+static u8 lane_to_slot[] = {
+       0, 0, 0, 0,
+       0, 0, 0, 0,
+       1, 1, 1, 1,
+       0, 0, 0, 0
+};
+
+/*
+ * This function initializes the lane_to_slot[] array. It reads RCW to check
+ * if Serdes2{E,F,G,H} is configured as slot 2 or as SFP and initializes
+ * lane_to_slot[] accordingly
+ */
+static void initialize_lane_to_slot(void)
+{
+       unsigned int  serdes2_prtcl;
+       ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+       serdes2_prtcl = in_be32(&gur->rcwsr[4]) &
+               FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
+       serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
+       debug("Initializing lane to slot: Serdes2 protocol: %x\n",
+                       serdes2_prtcl);
+
+       switch (serdes2_prtcl) {
+       case 0x18:
+               /*
+                * Configuration:
+                * SERDES: 2
+                * Lanes: A,B,C,D: SGMII
+                * Lanes: E,F: Aur
+                * Lanes: G,H: SRIO
+                */
+       case 0x91:
+               /*
+                * Configuration:
+                * SERDES: 2
+                * Lanes: A,B: SGMII
+                * Lanes: C,D: SRIO2
+                * Lanes: E,F,G,H: XAUI2
+                */
+       case 0x93:
+               /*
+                * Configuration:
+                * SERDES: 2
+                * Lanes: A,B,C,D: SGMII
+                * Lanes: E,F,G,H: XAUI2
+                */
+       case 0x98:
+               /*
+                * Configuration:
+                * SERDES: 2
+                * Lanes: A,B,C,D: XAUI2
+                * Lanes: E,F,G,H: XAUI2
+                */
+       case 0x9a:
+               /*
+                * Configuration:
+                * SERDES: 2
+                * Lanes: A,B: PCI
+                * Lanes: C,D: SGMII
+                * Lanes: E,F,G,H: XAUI2
+                */
+       case 0x9e:
+               /*
+                * Configuration:
+                * SERDES: 2
+                * Lanes: A,B,C,D: PCI
+                * Lanes: E,F,G,H: XAUI2
+                */
+       case 0xb2:
+               /*
+                * Configuration:
+                * SERDES: 2
+                * Lanes: A,B,C,D: PCI
+                * Lanes: E,F: SGMII 3&4
+                * Lanes: G,H: XFI
+                */
+       case 0xc2:
+               /*
+                * Configuration:
+                * SERDES: 2
+                * Lanes: A,B: SGMII
+                * Lanes: C,D: SRIO2
+                * Lanes: E,F,G,H: XAUI2
+                */
+               lane_to_slot[12] = 2;
+               lane_to_slot[13] = lane_to_slot[12];
+               lane_to_slot[14] = lane_to_slot[12];
+               lane_to_slot[15] = lane_to_slot[12];
+               break;
+
+       default:
+               printf("Fman: Unsupported SerDes2 Protocol 0x%02x\n",
+                               serdes2_prtcl);
+                       break;
+       }
+       return;
+}
+
+#endif /* #ifdef CONFIG_FMAN_ENET */
+
+int board_eth_init(bd_t *bis)
+{
+#ifdef CONFIG_FMAN_ENET
+       struct memac_mdio_info memac_mdio_info;
+       struct memac_mdio_info tg_memac_mdio_info;
+       unsigned int i;
+       unsigned int  serdes1_prtcl, serdes2_prtcl;
+       ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+       serdes1_prtcl = in_be32(&gur->rcwsr[4]) &
+               FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+       if (!serdes1_prtcl) {
+               printf("SERDES1 is not enabled\n");
+               return 0;
+       }
+       serdes1_prtcl >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+       debug("Using SERDES1 Protocol: 0x%x:\n", serdes1_prtcl);
+
+       serdes2_prtcl = in_be32(&gur->rcwsr[4]) &
+               FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
+       if (!serdes2_prtcl) {
+               printf("SERDES2 is not enabled\n");
+               return 0;
+       }
+       serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
+       debug("Using SERDES2 Protocol: 0x%x:\n", serdes2_prtcl);
+
+       printf("Initializing Fman\n");
+
+       initialize_lane_to_slot();
+
+       memac_mdio_info.regs =
+               (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
+       memac_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+       /* Register the real 1G MDIO bus */
+       fm_memac_mdio_init(bis, &memac_mdio_info);
+
+       tg_memac_mdio_info.regs =
+               (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
+       tg_memac_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
+
+       /* Register the real 10G MDIO bus */
+       fm_memac_mdio_init(bis, &tg_memac_mdio_info);
+
+       /*
+        * Program the two on board DTSEC PHY addresses assuming that they are
+        * all SGMII. RGMII is not supported on this board. Setting SGMII 5 and
+        * 6 to on board SGMII phys
+        */
+       fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
+       fm_info_set_phy_address(FM1_DTSEC6, CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
+
+       switch (serdes1_prtcl) {
+       case 0x2a:
+               /* Serdes 1: A-B SGMII, Configuring DTSEC 5 and 6 */
+               debug("Setting phy addresses for FM1_DTSEC5: %x and"
+                       "FM1_DTSEC6: %x\n", CONFIG_SYS_FM1_DTSEC5_PHY_ADDR,
+                       CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
+               /* Fixing Serdes clock by programming FPGA register */
+               QIXIS_WRITE(brdcfg[4], QIXIS_SRDS1CLK_125);
+               fm_info_set_phy_address(FM1_DTSEC5,
+                               CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
+               fm_info_set_phy_address(FM1_DTSEC6,
+                               CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
+               break;
+#ifdef CONFIG_PPC_B4420
+       case 0x18:
+               /* Serdes 1: A-D SGMII, Configuring on board dual SGMII Phy */
+               debug("Setting phy addresses for FM1_DTSEC3: %x and"
+                       "FM1_DTSEC4: %x\n", CONFIG_SYS_FM1_DTSEC5_PHY_ADDR,
+                       CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
+               /* Fixing Serdes clock by programming FPGA register */
+               QIXIS_WRITE(brdcfg[4], QIXIS_SRDS1CLK_125);
+               fm_info_set_phy_address(FM1_DTSEC3,
+                               CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
+               fm_info_set_phy_address(FM1_DTSEC4,
+                               CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
+               break;
+#endif
+       default:
+               printf("Fman:  Unsupported SerDes1 Protocol 0x%02x\n",
+                               serdes1_prtcl);
+               break;
+       }
+       switch (serdes2_prtcl) {
+       case 0x18:
+               debug("Setting phy addresses on SGMII Riser card for"
+                               "FM1_DTSEC ports: \n");
+               fm_info_set_phy_address(FM1_DTSEC1,
+                               CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR);
+               fm_info_set_phy_address(FM1_DTSEC2,
+                               CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR);
+               fm_info_set_phy_address(FM1_DTSEC3,
+                               CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR);
+               fm_info_set_phy_address(FM1_DTSEC4,
+                               CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR);
+               break;
+       case 0x49:
+               debug("Setting phy addresses on SGMII Riser card for"
+                               "FM1_DTSEC ports: \n");
+               fm_info_set_phy_address(FM1_DTSEC1,
+                               CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR);
+               fm_info_set_phy_address(FM1_DTSEC2,
+                               CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR);
+               fm_info_set_phy_address(FM1_DTSEC3,
+                               CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR);
+               break;
+       case 0x8d:
+       case 0xb2:
+               debug("Setting phy addresses on SGMII Riser card for"
+                               "FM1_DTSEC ports: \n");
+               fm_info_set_phy_address(FM1_DTSEC3,
+                               CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR);
+               fm_info_set_phy_address(FM1_DTSEC4,
+                               CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR);
+               break;
+       default:
+               printf("Fman:  Unsupported SerDes2 Protocol 0x%02x\n",
+                               serdes2_prtcl);
+               break;
+       }
+
+       for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+               int idx = i - FM1_DTSEC1;
+
+               switch (fm_info_get_enet_if(i)) {
+               case PHY_INTERFACE_MODE_SGMII:
+                       fm_info_set_mdio(i,
+                               miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
+                       break;
+               case PHY_INTERFACE_MODE_NONE:
+                       fm_info_set_phy_address(i, 0);
+                       break;
+               default:
+                       printf("Fman1: DTSEC%u set to unknown interface %i\n",
+                                       idx + 1, fm_info_get_enet_if(i));
+                       fm_info_set_phy_address(i, 0);
+                       break;
+               }
+       }
+
+       cpu_eth_init(bis);
+#endif
+
+       return pci_eth_init(bis);
+}
+
+void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
+                             enum fm_port port, int offset)
+{
+       int phy;
+       char alias[32];
+
+       if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) {
+               phy = fm_info_get_phy_address(port);
+
+               sprintf(alias, "phy_sgmii_%x", phy);
+               fdt_set_phy_handle(fdt, compat, addr, alias);
+       }
+}
+
+void fdt_fixup_board_enet(void *fdt)
+{
+       int i;
+       char alias[32];
+
+       for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+               switch (fm_info_get_enet_if(i)) {
+               case PHY_INTERFACE_MODE_NONE:
+                       sprintf(alias, "ethernet%u", i);
+                       fdt_status_disabled_by_alias(fdt, alias);
+                       break;
+               default:
+                       break;
+               }
+       }
+}
diff --git a/board/freescale/b4860qds/law.c b/board/freescale/b4860qds/law.c
new file mode 100644 (file)
index 0000000..4142e01
--- /dev/null
@@ -0,0 +1,44 @@
+/*
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+       SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+       SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+       SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
+#endif
+       SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+       SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE_PHYS
+       SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/b4860qds/pci.c b/board/freescale/b4860qds/pci.c
new file mode 100644 (file)
index 0000000..b130d13
--- /dev/null
@@ -0,0 +1,39 @@
+/*
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+void pci_init_board(void)
+{
+       fsl_pcie_init_board(0);
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+       FT_FSL_PCI_SETUP;
+}
diff --git a/board/freescale/b4860qds/tlb.c b/board/freescale/b4860qds/tlb.c
new file mode 100644 (file)
index 0000000..373cb78
--- /dev/null
@@ -0,0 +1,127 @@
+/*
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+       /* TLB 0 - for temp stack in cache */
+       SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+                     CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+                     MAS3_SX|MAS3_SW|MAS3_SR, 0,
+                     0, 0, BOOKE_PAGESZ_4K, 0),
+       SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+                     CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+                     MAS3_SX|MAS3_SW|MAS3_SR, 0,
+                     0, 0, BOOKE_PAGESZ_4K, 0),
+       SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+                     CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+                     MAS3_SX|MAS3_SW|MAS3_SR, 0,
+                     0, 0, BOOKE_PAGESZ_4K, 0),
+       SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+                     CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+                     MAS3_SX|MAS3_SW|MAS3_SR, 0,
+                     0, 0, BOOKE_PAGESZ_4K, 0),
+
+       /* TLB 1 */
+       /* *I*** - Covers boot page */
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
+       /*
+        * *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the
+        * SRAM is at 0xfff00000, it covered the 0xfffff000.
+        */
+       SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
+                       MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+                       0, 0, BOOKE_PAGESZ_1M, 1),
+#else
+       SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+                     MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+                     0, 0, BOOKE_PAGESZ_4K, 1),
+#endif
+
+       /* *I*G* - CCSRBAR */
+       SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+                     MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+                     0, 1, BOOKE_PAGESZ_16M, 1),
+
+       /* *I*G* - Flash, localbus */
+       /* This will be changed to *I*G* after relocation to RAM. */
+       SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+                     MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+                     0, 2, BOOKE_PAGESZ_256M, 1),
+
+       /* *I*G* - PCI */
+       SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+                     MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+                     0, 3, BOOKE_PAGESZ_256M, 1),
+
+       SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x10000000,
+                      CONFIG_SYS_PCIE1_MEM_PHYS + 0x10000000,
+                     MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+                     0, 4, BOOKE_PAGESZ_256M, 1),
+
+       /* *I*G* - PCI I/O */
+       SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+                     MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+                     0, 5, BOOKE_PAGESZ_64K, 1),
+
+       /* Bman/Qman */
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+       SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+                     MAS3_SX|MAS3_SW|MAS3_SR, 0,
+                     0, 6, BOOKE_PAGESZ_16M, 1),
+       SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
+                     CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
+                     MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+                     0, 7, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+       SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+                     MAS3_SX|MAS3_SW|MAS3_SR, 0,
+                     0, 8, BOOKE_PAGESZ_16M, 1),
+       SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
+                     CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
+                     MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+                     0, 9, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+       SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+                     MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+                     0, 10, BOOKE_PAGESZ_4M, 1),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE
+       /*
+        * *I*G - NAND
+        * entry 14 and 15 has been used hard coded, they will be disabled
+        * in cpu_init_f, so we use entry 16 for nand.
+        */
+       SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+                       MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+                       0, 11, BOOKE_PAGESZ_64K, 1),
+#endif
+       SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS,
+                     MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+                     0, 12, BOOKE_PAGESZ_4K, 1),
+
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
index 6d71f18ffe5ea33ebcac3e8c91a6074c9d51e0a9..0a2ed40973fd7043db14d5fbe7ceb7b2f1a67eea 100644 (file)
@@ -862,6 +862,12 @@ stxssa_4M                    powerpc     mpc85xx     stxssa              stx
 T4240QDS                     powerpc     mpc85xx     t4qds               freescale
 T4240QDS_SDCARD              powerpc     mpc85xx     t4qds               freescale     -           T4240QDS:RAMBOOT_PBL,SDCARD,SYS_TEXT_BASE=0xFFF80000
 T4240QDS_SPIFLASH            powerpc     mpc85xx     t4qds               freescale     -           T4240QDS:RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000
+B4860QDS                     powerpc     mpc85xx     b4860qds            freescale      -           B4860QDS:PPC_B4860
+B4860QDS_NAND               powerpc     mpc85xx     b4860qds            freescale      -           B4860QDS:PPC_B4860,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000
+B4860QDS_SPIFLASH            powerpc     mpc85xx     b4860qds            freescale     -           B4860QDS:PPC_B4860,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000
+B4420QDS                     powerpc     mpc85xx     b4860qds            freescale     -           B4860QDS:PPC_B4420
+B4420QDS_NAND               powerpc     mpc85xx     b4860qds            freescale      -           B4860QDS:PPC_B4420,RAMBOOT_PBL,NAND,SYS_TEXT_BASE=0xFFF80000
+B4420QDS_SPIFLASH            powerpc     mpc85xx     b4860qds            freescale     -           B4860QDS:PPC_B4420,RAMBOOT_PBL,SPIFLASH,SYS_TEXT_BASE=0xFFF80000
 xpedite520x                  powerpc     mpc85xx     -                   xes
 xpedite537x                  powerpc     mpc85xx     -                   xes
 xpedite550x                  powerpc     mpc85xx     -                   xes
diff --git a/doc/README.b4860qds b/doc/README.b4860qds
new file mode 100644 (file)
index 0000000..f6c5ff8
--- /dev/null
@@ -0,0 +1,330 @@
+Overview
+--------
+The B4860QDS is a Freescale reference board that hosts the B4860 SoC (and variants).
+
+B4860 Overview
+-------------
+The B4860 QorIQ Qonverge device is a Freescale high-end, multicore SoC based on
+StarCore and Power Architecture® cores. It targets the broadband wireless 
+infrastructure and builds upon the proven success of the existing multicore
+DSPs and Power CPUs. It is designed to bolster the rapidly changing and
+expanding wireless markets, such as 3GLTE (FDD and TDD), LTE-Advanced, and UMTS.
+
+The B4860 is a highly-integrated StarCore and Power Architecture processor that
+contains:
+. Six fully-programmable StarCore SC3900 FVP subsystems, divided into three
+clusters-each core runs up to 1.2 GHz, with an architecture highly optimized for
+wireless base station applications
+. Four dual-thread e6500 Power Architecture processors organized in one cluster-each
+core runs up to 1.8 GHz
+. Two DDR3/3L controllers for high-speed, industry-standard memory interface each
+runs at up to 1866.67 MHz
+. MAPLE-B3 hardware acceleration-for forward error correction schemes including
+Turbo or Viterbi decoding, Turbo encoding and rate matching, MIMO MMSE
+equalization scheme, matrix operations, CRC insertion and check, DFT/iDFT and
+FFT/iFFT calculations, PUSCH/PDSCH acceleration, and UMTS chip rate
+acceleration
+. CoreNet fabric that fully supports coherency using MESI protocol between the
+  e6500 cores, SC3900 FVP cores, memories and external interfaces.
+  CoreNet fabric interconnect runs at 667 MHz and supports coherent and
+  non-coherent out of order transactions with prioritization and bandwidth
+  allocation amongst CoreNet endpoints.
+. Data Path Acceleration Architecture, which includes the following:
+. Frame Manager (FMan), which supports in-line packet parsing and general
+  classification to enable policing and QoS-based packet distribution
+. Queue Manager (QMan) and Buffer Manager (BMan), which allow offloading
+  of queue management, task management, load distribution, flow ordering, buffer
+  management, and allocation tasks from the cores
+. Security engine (SEC 5.3)-crypto-acceleration for protocols such as IPsec,
+  SSL, and 802.16
+. RapidIO manager (RMAN) - Support SRIO types 8, 9, 10, and 11 (inbound and
+  outbound). Supports types 5, 6 (outbound only)
+. Large internal cache memory with snooping and stashing capabilities for
+  bandwidth saving and high utilization of processor elements. The 9856-Kbyte
+  internal memory space includes the following:
+. 32 Kbyte L1 ICache per e6500/SC3900 core
+. 32 Kbyte L1 DCache per e6500/SC3900 core
+. 2048 Kbyte unified L2 cache for each SC3900 FVP cluster
+. 2048 Kbyte unified L2 cache for the e6500 cluster
+. Two 512 Kbyte shared L3 CoreNet platform caches (CPC)
+. Sixteen 10-GHz SerDes lanes serving:
+. Two Serial RapidIO interfaces.
+       - Each supports up to 4 lanes and a total of up to 8 lanes
+. Up to 8-lanes Common Public Radio Interface (CPRI) controller for glue-less
+  antenna connection
+. Two 10-Gbit Ethernet controllers (10GEC)
+. Six 1G/2.5-Gbit Ethernet controllers for network communications
+. PCI Express controller
+. Debug (Aurora)
+. Two OCeaN DMAs
+. Various system peripherals
+. 182 32-bit timers
+
+B4860QDS Overview
+------------------
+- DDRC1: Ten separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 4 GB
+  of memory in two ranks of 2 GB.
+- DDRC2: Five separate DDR3 parts of 16-bit to support 72-bit (ECC) at 1866MT/s, ECC, 2 GB
+  of memory. Single rank.
+- SerDes 1 multiplexing: Two Vitesse (transmit and receive path) cross-point 16x16 switch
+  VSC3316
+- SerDes 2 multiplexing: Two Vitesse (transmit and receive path) cross-point 8x8 switch VSC3308
+- USB 2.0 ULPI PHY USB3315 by SMSC supports USB port in host mode.
+  B4860 UART port is available over USB-to-UART translator USB2SER or over RS232 flat cable.
+- A Vitesse dual SGMII phy VSC8662 links the B4860 SGMII lines to 2xRJ-45 copper connectors
+  for Stand-alone mode and to the 1000Base-X over AMC MicroTCA connector ports 0 and 2 for
+  AMC mode.
+- The B4860 configuration may be loaded from nine bits coded reset configuration reset source. The
+  RCW source is set by appropriate DIP-switches:
+- 16-bit NOR Flash / PROMJet
+- QIXIS 8-bit NOR Flash Emulator
+- 8-bit NAND Flash
+- 24-bit SPI Flash
+- Long address I2C EEPROM
+- Available debug interfaces are:
+       - On-board eCWTAP controller with ETH and USB I/F
+       - JTAG/COP 16-pin header for any external TAP controller
+       - External JTAG source over AMC to support B2B configuration
+       - 70-pin Aurora debug connector
+- QIXIS (FPGA) logic:
+       - 2 KB internal memory space including
+- IDT840NT4 clock synthesizer provides B4860 essential clocks : SYSCLK, DDRCLK1,2 and
+  RTCCLK.
+- Two 8T49N222A SerDes ref clock devices support two SerDes port clock frequency - total four
+  refclk, including CPRI clock scheme.
+
+B4420 Personality
+--------------------
+
+B4420 Personality
+--------------------
+B4420 is a reduced personality of B4860 with less core/clusters(both SC3900 and e6500), less DDR
+controllers, less serdes lanes, less SGMII interfaces and reduced target frequencies. 
+
+Key differences between B4860 and B4420
+----------------------------------------
+B4420 has:
+1. Less e6500 cores: 1 cluster with 2 e6500 cores
+2. Less SC3900 cores/clusters: 1 cluster with 2 SC3900 cores per cluster.
+3. Single DDRC
+4. 2X 4 lane serdes
+5. 3 SGMII interfaces
+6. no sRIO
+7. no 10G
+
+B4860QDS Default Settings
+-------------------------
+
+Switch Settings
+----------------
+
+SW1    OFF [0] OFF [1] OFF [1] OFF [0] OFF [1] OFF [0] OFF [1] OFF [1]
+SW2    ON      ON      ON      ON      ON      ON      OFF     OFF
+SW3    OFF     OFF     OFF     ON      OFF     OFF     ON      OFF
+SW5    OFF     OFF     OFF     OFF     OFF     OFF     ON      ON
+
+Note: PCIe slots modes: All the PCIe devices work as Root Complex.
+Note: Boot location: NOR flash.
+
+SysClk/Core(e6500)/CCB/DDR/FMan/DDRCLK/StarCore/CPRI-Maple/eTVPE-Maple/ULB-Maple
+66MHz/1.6GHz/667MHz/1.6GHz data rate/667MHz/133MHz/1200MHz/500MHz/800MHz/667MHz
+
+a) NAND boot   
+       SW1 [1.1] = 0
+       SW2 [1.1] = 1
+       SW3 [1:4] = 0001
+b) NOR boot
+       SW1 [1.1] = 1
+       SW2 [1.1] = 0
+       SW3 [1:4] = 1000.
+
+B4420QDS Default Settings
+-------------------------
+
+Switch Settings
+----------------
+SW1    OFF[0]  OFF [0] OFF [0] OFF [0] OFF [0] OFF [0] OFF [0] OFF [0]
+SW2    ON      OFF     ON      OFF     ON      ON      OFF     OFF
+SW3    OFF     OFF     OFF     ON      OFF     OFF     ON      OFF
+SW5    OFF     OFF     OFF     OFF     OFF     OFF     ON      ON
+
+Note: PCIe slots modes: All the PCIe devices work as Root Complex.
+Note: Boot location: NOR flash.
+
+SysClk/Core(e6500)/CCB/DDR/FMan/DDRCLK/StarCore/CPRI-Maple/eTVPE-Maple/ULB-Maple
+66MHz/1.6GHz/667MHz/1.6GHz data rate/667MHz/133MHz/1200MHz/500MHz/800MHz/667MHz
+
+a) NAND boot   
+       SW1 [1.1] = 0
+       SW2 [1.1] = 1
+       SW3 [1:4] = 0001
+b) NOR boot
+       SW1 [1.1] = 1
+       SW2 [1.1] = 0
+       SW3 [1:4] = 1000.
+
+Memory map on B4860QDS
+----------------------
+The addresses in brackets are physical addresses.
+
+Start Address  End Address     Description     Size
+0xF_FFDF_1000  0xF_FFFF_FFFF   Free            2 MB
+0xF_FFDF_0000  0xF_FFDF_0FFF   IFC - FPGA      4 KB
+0xF_FF81_0000  0xF_FFDE_FFFF   Free            5 MB
+0xF_FF80_0000  0xF_FF80_FFFF   IFC NAND Flash  64 KB
+0xF_FF00_0000  0xF_FF7F_FFFF   Free            8 MB
+0xF_FE00_0000  0xF_FEFF_FFFF   CCSRBAR         16 MB
+0xF_F801_0000  0xF_FDFF_FFFF   Free            95 MB
+0xF_F800_0000  0xF_F800_FFFF   PCIe I/O Space  64 KB
+0xF_F600_0000  0xF_F7FF_FFFF   QMAN s/w portal 32 MB
+0xF_F400_0000  0xF_F5FF_FFFF   BMAN s/w portal 32 MB
+0xF_F000_0000  0xF_F3FF_FFFF   Free            64 MB
+0xF_E800_0000  0xF_EFFF_FFFF   IFC  NOR Flash  128 MB
+0xF_E000_0000  0xF_E7FF_FFFF   Promjet         128 MB
+0xF_A0C0_0000  0xF_DFFF_FFFF   Free            1012 MB
+0xF_A000_0000  0xF_A0BF_FFFF   MAPLE0/1/2      12 MB
+0xF_0040_0000  0xF_9FFF_FFFF   Free            12 GB
+0xF_0000_0000  0xF_003F_FFFF   DCSR            4 MB
+0xC_4000_0000  0xE_FFFF_FFFF   Free            11 GB
+0xC_3000_0000  0xC_3FFF_FFFF   sRIO-2 I/O      256 MB
+0xC_2000_0000  0xC_2FFF_FFFF   sRIO-1 I/O      256 MB
+0xC_0000_0000  0xC_1FFF_FFFF   PCIe Mem Space  512 MB
+0x1_0000_0000  0xB_FFFF_FFFF   Free            44 GB
+0x0_8000_0000  0x0_FFFF_FFFF   DDRC1           2 GB
+0x0_0000_0000  0x0_7FFF_FFFF   DDRC2           2 GB
+
+Memory map on B4420QDS
+----------------------
+The addresses in brackets are physical addresses.
+
+Start Address  End Address     Description     Size
+0xF_FFDF_1000  0xF_FFFF_FFFF   Free            2 MB
+0xF_FFDF_0000  0xF_FFDF_0FFF   IFC - FPGA      4 KB
+0xF_FF81_0000  0xF_FFDE_FFFF   Free            5 MB
+0xF_FF80_0000  0xF_FF80_FFFF   IFC NAND Flash  64 KB
+0xF_FF00_0000  0xF_FF7F_FFFF   Free            8 MB
+0xF_FE00_0000  0xF_FEFF_FFFF   CCSRBAR         16 MB
+0xF_F801_0000  0xF_FDFF_FFFF   Free            95 MB
+0xF_F800_0000  0xF_F800_FFFF   PCIe I/O Space  64 KB
+0xF_F600_0000  0xF_F7FF_FFFF   QMAN s/w portal 32 MB
+0xF_F400_0000  0xF_F5FF_FFFF   BMAN s/w portal 32 MB
+0xF_F000_0000  0xF_F3FF_FFFF   Free            64 MB
+0xF_E800_0000  0xF_EFFF_FFFF   IFC  NOR Flash  128 MB
+0xF_E000_0000  0xF_E7FF_FFFF   Promjet         128 MB
+0xF_A0C0_0000  0xF_DFFF_FFFF   Free            1012 MB
+0xF_A000_0000  0xF_A0BF_FFFF   MAPLE0/1/2      12 MB
+0xF_0040_0000  0xF_9FFF_FFFF   Free            12 GB
+0xF_0000_0000  0xF_003F_FFFF   DCSR            4 MB
+0xC_4000_0000  0xE_FFFF_FFFF   Free            11 GB
+0xC_3000_0000  0xC_3FFF_FFFF   sRIO-2 I/O      256 MB
+0xC_2000_0000  0xC_2FFF_FFFF   sRIO-1 I/O      256 MB
+0xC_0000_0000  0xC_1FFF_FFFF   PCIe Mem Space  512 MB
+0x1_0000_0000  0xB_FFFF_FFFF   Free            44 GB
+0x0_0000_0000  0x0_FFFF_FFFF   DDRC1           4 GB
+
+
+NOR Flash memory Map on B4860 and B4420QDS
+------------------------------------------
+ Start          End            Definition                      Size
+0xEFF80000     0xEFFFFFFF      u-boot (current bank)           512KB
+0xEFF60000     0xEFF7FFFF      u-boot env (current bank)       128KB
+0xEFF40000     0xEFF5FFFF      FMAN Ucode (current bank)       128KB
+0xEF300000     0xEFF3FFFF      rootfs (alternate bank)         12MB + 256KB
+0xEE800000     0xEE8FFFFF      device tree (alternate bank)    1MB
+0xEE020000     0xEE6FFFFF      Linux.uImage (alternate bank)   6MB+896KB
+0xEE000000     0xEE01FFFF      RCW (alternate bank)            128KB
+0xEDF80000     0xEDFFFFFF      u-boot (alternate bank)         512KB
+0xEDF60000     0xEDF7FFFF      u-boot env (alternate bank)     128KB
+0xEDF40000     0xEDF5FFFF      FMAN ucode (alternate bank)     128KB
+0xED300000     0xEDF3FFFF      rootfs (current bank)           12MB+256MB
+0xEC800000     0xEC8FFFFF      device tree (current bank)      1MB
+0xEC020000     0xEC6FFFFF      Linux.uImage (current bank)     6MB+896KB
+0xEC000000     0xEC01FFFF      RCW (current bank)              128KB
+
+Various Software configurations/environment variables/commands
+--------------------------------------------------------------
+The below commands apply to both B4860QDS and B4420QDS.
+
+1. U-boot environment variable hwconfig 
+   The default hwconfig is:
+       hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;usb1:
+                                       dr_mode=host,phy_type=ulpi
+   Note: For USB gadget set "dr_mode=peripheral"
+
+2. FMAN Ucode versions
+   fsl_fman_ucode_B4860_106_3_6.bin
+
+3. Switching to alternate bank
+   Commands for switching to alternate bank.
+
+       1. To change from vbank0 to vbank2 
+               => qixis_reset altbank (it will boot using vbank2)
+
+       2.To change from vbank2 to vbank0
+               => qixis reset (it will boot using vbank0)
+
+4. To change personality of board
+   For changing personality from B4860 to B4420
+       1)Boot from vbank0
+       2)Flash vbank2 with b4420 rcw and u-boot
+       3)Give following commands to uboot prompt
+          => mw.b ffdf0040 0x30; 
+          => mw.b ffdf0010 0x00;
+          => mw.b ffdf0062 0x02;
+          => mw.b ffdf0050 0x02;
+          => mw.b ffdf0010 0x30;
+          => reset
+
+   Note: Power off cycle will lead to default switch settings.
+   Note: 0xffdf0000 is the address of the QIXIS FPGA.
+
+5. Switching between NOR and NAND boot(RCW src changed from NOR <-> NAND)
+
+   To change from NOR to NAND boot give following command on uboot prompt
+       => mw.b ffdf0040 0x30
+       => mw.b ffdf0010 0x00 
+       => mw.b 0xffdf0050 0x08
+       => mw.b 0xffdf0060 0x82
+       => mw.b ffdf0061 0x00
+       => mw.b ffdf0010 0x30   
+       => reset
+
+   To change from NAND to NOR boot give following command on uboot prompt:
+       => mw.b ffdf0040 0x30
+       => mw.b ffdf0010 0x00 
+       => mw.b 0xffdf0050 0x00(for vbank0) or (mw.b 0xffdf0050 0x02 for vbank2)
+       => mw.b 0xffdf0060 0x12
+       => mw.b ffdf0061 0x01
+       => mw.b ffdf0010 0x30   
+       => reset
+
+   Note: Power off cycle will lead to default switch settings.
+   Note: 0xffdf0000 is the address of the QIXIS FPGA.
+
+6.  Ethernet interfaces for B4860QDS 
+   Serdes protocosl tested:
+   0x2a, 0x8d (serdes1, serdes2) [DEFAULT]
+   0x2a, 0xb2 (serdes1, serdes2)
+
+   When using [DEFAULT] RCW, which including 2 * 1G SGMII on board and 2 * 1G
+   SGMII on SGMII riser card. 
+   Under U-boot these network interfaces are recognized as:
+   FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5 and FM1@DTSEC6.
+
+   On Linux the interfaces are renamed as:
+       . eth2 -> fm1-gb2
+       . eth3 -> fm1-gb3
+       . eth4 -> fm1-gb4
+       . eth5 -> fm1-gb5
+
+7. RCW and Ethernet interfaces for B4420QDS 
+   Serdes protocosl tested:
+   0x18, 0x9e (serdes1, serdes2)
+
+   Under U-boot these network interfaces are recognized as:
+   FM1@DTSEC3, FM1@DTSEC4 and  e1000#0.
+
+   On Linux the interfaces are renamed as:
+       . eth2 -> fm1-gb2
+       . eth3 -> fm1-gb3
diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h
new file mode 100644 (file)
index 0000000..b09119a
--- /dev/null
@@ -0,0 +1,820 @@
+/*
+ * Copyright 2011-2012 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * B4860 QDS board configuration file
+ */
+#define CONFIG_B4860QDS
+#define CONFIG_PHYS_64BIT
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_RAMBOOT_TEXT_BASE       CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS    0xfffffffc
+#endif
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE
+#define CONFIG_E6500
+#define CONFIG_E500                    /* BOOKE e500 family */
+#define CONFIG_E500MC                  /* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV           /* Category E.HV supported */
+#define CONFIG_MPC85xx                 /* MPC85xx/PQ3 platform */
+#define CONFIG_FSL_CORENET             /* Freescale CoreNet platform */
+#define CONFIG_MP                      /* support multiple processors */
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE   0xeff80000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS    0xeffffffc
+#endif
+
+#define CONFIG_SYS_FSL_CPC             /* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC             CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_IFC                 /* Enable IFC Support */
+#define CONFIG_PCI                     /* Enable PCI/PCIE */
+#define CONFIG_PCIE1                   /* PCIE controler 1 */
+#define CONFIG_FSL_PCI_INIT            /* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT           /* enable 64-bit PCI resources */
+
+#ifndef CONFIG_PPC_B4420
+#define CONFIG_SYS_SRIO
+#define CONFIG_SRIO1                   /* SRIO port 1 */
+#define CONFIG_SRIO2                   /* SRIO port 2 */
+#endif
+
+#define CONFIG_FSL_LAW                 /* Use common FSL init code */
+
+/* I2C bus multiplexer */
+#define I2C_MUX_PCA_ADDR                0x77
+
+/* VSC Crossbar switches */
+#define CONFIG_VSC_CROSSBAR
+#define I2C_CH_DEFAULT                  0x8
+#define I2C_CH_VSC3316                  0xc
+#define I2C_CH_VSC3308                  0xd
+
+#define VSC3316_TX_ADDRESS              0x70
+#define VSC3316_RX_ADDRESS              0x71
+#define VSC3308_TX_ADDRESS              0x02
+#define VSC3308_RX_ADDRESS              0x03
+
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_SYS_NO_FLASH
+#define CONFIG_ENV_IS_NOWHERE
+#else
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#endif
+
+#ifndef CONFIG_SYS_NO_FLASH
+#if defined(CONFIG_SPIFLASH)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS              0
+#define CONFIG_ENV_SPI_CS               0
+#define CONFIG_ENV_SPI_MAX_HZ           10000000
+#define CONFIG_ENV_SPI_MODE             0
+#define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
+#define CONFIG_ENV_OFFSET               0x100000        /* 1MB */
+#define CONFIG_ENV_SECT_SIZE            0x10000
+#elif defined(CONFIG_SDCARD)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV          0
+#define CONFIG_ENV_SIZE                        0x2000
+#define CONFIG_ENV_OFFSET              (512 * 1097)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE                        CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET              (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE                0x2000
+#define CONFIG_ENV_SECT_SIZE   0x20000 /* 128K (one sector) */
+#endif
+#else /* CONFIG_SYS_NO_FLASH */
+#define CONFIG_ENV_SIZE                0x2000
+#define CONFIG_ENV_SECT_SIZE   0x20000 /* 128K (one sector) */
+#endif
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+#define CONFIG_SYS_CLK_FREQ    get_board_sys_clk() /* sysclk for MPC85xx */
+#define CONFIG_DDR_CLK_FREQ    get_board_ddr_clk()
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BTB                     /* toggle branch predition */
+#define CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE          0xdeadbeef
+#endif
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP
+#define CONFIG_SYS_NUM_ADDR_MAP                64      /* number of TLB1 entries */
+#endif
+
+#if 0
+#define CONFIG_POST CONFIG_SYS_POST_MEMORY     /* test POST memory test */
+#endif
+#define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END         0x00400000
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_PANIC_HANG      /* do not reset board on panic */
+
+/*
+ *  Config the L3 Cache as L3 SRAM
+ */
+#define CONFIG_SYS_INIT_L3_ADDR                CONFIG_RAMBOOT_TEXT_BASE
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_DCSRBAR             0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS                0xf00000000ull
+#endif
+
+/* EEPROM */
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM      0
+#define CONFIG_SYS_I2C_EEPROM_ADDR     0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE      0x00000000
+#define CONFIG_SYS_SDRAM_BASE          CONFIG_SYS_DDR_SDRAM_BASE
+
+/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */
+#define CONFIG_DIMM_SLOTS_PER_CTLR     1
+#define CONFIG_CHIP_SELECTS_PER_CTRL   (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_DDR_RAW_TIMING
+#define CONFIG_FSL_DDR3
+#define CONFIG_FSL_DDR_INTERACTIVE
+
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define SPD_EEPROM_ADDRESS1    0x51
+#define SPD_EEPROM_ADDRESS2    0x53
+
+#define SPD_EEPROM_ADDRESS     SPD_EEPROM_ADDRESS1
+#define CONFIG_SYS_SDRAM_SIZE  2048    /* for fixed parameter use */
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_FLASH_BASE  0xe0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_FLASH_BASE_PHYS     (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
+#else
+#define CONFIG_SYS_FLASH_BASE_PHYS     CONFIG_SYS_FLASH_BASE
+#endif
+
+#define CONFIG_SYS_NOR0_CSPR_EXT       (0xf)
+#define CONFIG_SYS_NOR0_CSPR   (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
+                               + 0x8000000) | \
+                               CSPR_PORT_SIZE_16 | \
+                               CSPR_MSEL_NOR | \
+                               CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR_EXT       (0xf)
+#define CONFIG_SYS_NOR1_CSPR   (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+                               CSPR_PORT_SIZE_16 | \
+                               CSPR_MSEL_NOR | \
+                               CSPR_V)
+#define CONFIG_SYS_NOR_AMASK   IFC_AMASK(128 * 1024 * 1024)
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_CSOR    CSOR_NOR_ADM_SHIFT(4)
+#define CONFIG_SYS_NOR_FTIM0   (FTIM0_NOR_TACSE(0x01) | \
+                               FTIM0_NOR_TEADC(0x01) | \
+                               FTIM0_NOR_TEAHC(0x20))
+#define CONFIG_SYS_NOR_FTIM1   (FTIM1_NOR_TACO(0x35) | \
+                               FTIM1_NOR_TRAD_NOR(0x1A) |\
+                               FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2   (FTIM2_NOR_TCS(0x01) | \
+                               FTIM2_NOR_TCH(0x0E) | \
+                               FTIM2_NOR_TWPH(0x0E) | \
+                               FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3   0x0
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS     45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS     2       /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT      1024    /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT    60000   /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT    500     /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST    {CONFIG_SYS_FLASH_BASE_PHYS \
+                                       + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
+
+#define CONFIG_FSL_QIXIS       /* use common QIXIS code */
+#define CONFIG_FSL_QIXIS_V2
+#define QIXIS_BASE             0xffdf0000
+#ifdef CONFIG_PHYS_64BIT
+#define QIXIS_BASE_PHYS                (0xf00000000ull | QIXIS_BASE)
+#else
+#define QIXIS_BASE_PHYS                QIXIS_BASE
+#endif
+#define QIXIS_LBMAP_SWITCH             0x01
+#define QIXIS_LBMAP_MASK               0x0f
+#define QIXIS_LBMAP_SHIFT              0
+#define QIXIS_LBMAP_DFLTBANK           0x00
+#define QIXIS_LBMAP_ALTBANK            0x02
+#define QIXIS_RST_CTL_RESET            0x31
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE   0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START  0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE  0x08
+
+#define CONFIG_SYS_CSPR3_EXT   (0xf)
+#define CONFIG_SYS_CSPR3       (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
+                               | CSPR_PORT_SIZE_8 \
+                               | CSPR_MSEL_GPCM \
+                               | CSPR_V)
+#define CONFIG_SYS_AMASK3      IFC_AMASK(4 * 1024)
+#define CONFIG_SYS_CSOR3       0x0
+/* QIXIS Timing parameters for IFC CS3 */
+#define CONFIG_SYS_CS3_FTIM0           (FTIM0_GPCM_TACSE(0x0e) | \
+                                       FTIM0_GPCM_TEADC(0x0e) | \
+                                       FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS3_FTIM1           (FTIM1_GPCM_TACO(0x0e) | \
+                                       FTIM1_GPCM_TRAD(0x1f))
+#define CONFIG_SYS_CS3_FTIM2           (FTIM2_GPCM_TCS(0x0e) | \
+                                       FTIM2_GPCM_TCH(0x0) | \
+                                       FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS3_FTIM3           0x0
+
+/* NAND Flash on IFC */
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE           0xff800000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_NAND_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_NAND_BASE)
+#else
+#define CONFIG_SYS_NAND_BASE_PHYS      CONFIG_SYS_NAND_BASE
+#endif
+
+#define CONFIG_SYS_NAND_CSPR_EXT       (0xf)
+#define CONFIG_SYS_NAND_CSPR   (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+                               | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+                               | CSPR_MSEL_NAND        /* MSEL = NAND */ \
+                               | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK  IFC_AMASK(64 * 1024)
+
+#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
+                               | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
+                               | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
+                               | CSOR_NAND_RAL_3       /* RAL = 2Byes */ \
+                               | CSOR_NAND_PGS_2K      /* Page Size = 2K */ \
+                               | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
+                               | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0          (FTIM0_NAND_TCCST(0x07) | \
+                                       FTIM0_NAND_TWP(0x18)   | \
+                                       FTIM0_NAND_TWCHT(0x07) | \
+                                       FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1          (FTIM1_NAND_TADLE(0x32) | \
+                                       FTIM1_NAND_TWBE(0x39)  | \
+                                       FTIM1_NAND_TRR(0x0e)   | \
+                                       FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2          (FTIM2_NAND_TRAD(0x0f) | \
+                                       FTIM2_NAND_TREH(0x0a) | \
+                                       FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3          0x0
+
+#define CONFIG_SYS_NAND_DDR_LAW                11
+
+#define CONFIG_SYS_NAND_BASE_LIST      { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE     1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE     (128 * 1024)
+
+#if defined(CONFIG_NAND)
+#define CONFIG_SYS_CSPR0_EXT           CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0               CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0              CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0               CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0           CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1           CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2           CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3           CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR2_EXT           CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR2               CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK2              CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR2               CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS2_FTIM0           CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS2_FTIM1           CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS2_FTIM2           CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS2_FTIM3           CONFIG_SYS_NOR_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT           CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0               CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0              CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0               CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0           CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1           CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2           CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3           CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT           CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR2               CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK2              CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR2               CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS2_FTIM0           CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS2_FTIM1           CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS2_FTIM2           CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS2_FTIM3           CONFIG_SYS_NAND_FTIM3
+#endif
+#define CONFIG_SYS_CSPR1_EXT           CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR1               CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK1              CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1               CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0           CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1           CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2           CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3           CONFIG_SYS_NOR_FTIM3
+
+#define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_TEXT_BASE
+
+#if defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_R
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR       0xfdd00000      /* Initial L1 address */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH     0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW      0xfe0ec000
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+       ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#else
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS  0xfe0ec000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
+#endif
+#define CONFIG_SYS_INIT_RAM_SIZE               0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - \
+                                       GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN         (512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN          (4 * 1024 * 1024)
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX      1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE    1
+#define CONFIG_SYS_NS16550_CLK         (get_bus_freq(0)/2)
+
+#define CONFIG_SYS_BAUDRATE_TABLE      \
+       {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3        (CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4        (CONFIG_SYS_CCSRBAR+0x11D600)
+#define CONFIG_SERIAL_MULTI            /* Enable both serial ports */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV   /* determine from environment */
+
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE     /* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_FSL_I2C         /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C                /* I2C with hardware support */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_SYS_I2C_SPEED           400000  /* I2C speed in Hz */
+#define CONFIG_SYS_I2C_SLAVE           0x7F
+#define CONFIG_SYS_I2C_OFFSET          0x118000
+#define CONFIG_SYS_I2C2_OFFSET         0x119000
+
+/*
+ * RTC configuration
+ */
+#define RTC
+#define CONFIG_RTC_DS3231               1
+#define CONFIG_SYS_I2C_RTC_ADDR         0x68
+
+/*
+ * RapidIO
+ */
+#ifdef CONFIG_SYS_SRIO
+#ifdef CONFIG_SRIO1
+#define CONFIG_SYS_SRIO1_MEM_VIRT      0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_SRIO1_MEM_PHYS      0xc20000000ull
+#else
+#define CONFIG_SYS_SRIO1_MEM_PHYS      0xa0000000
+#endif
+#define CONFIG_SYS_SRIO1_MEM_SIZE      0x10000000      /* 256M */
+#endif
+
+#ifdef CONFIG_SRIO2
+#define CONFIG_SYS_SRIO2_MEM_VIRT      0xb0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_SRIO2_MEM_PHYS      0xc30000000ull
+#else
+#define CONFIG_SYS_SRIO2_MEM_PHYS      0xb0000000
+#endif
+#define CONFIG_SYS_SRIO2_MEM_SIZE      0x10000000      /* 256M */
+#endif
+#endif
+
+/*
+ * for slave u-boot IMAGE instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000       /* 512K */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
+/*
+ * for slave UCODE and ENV instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000   /* 256K */
+
+/* slave core release by master*/
+#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
+#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
+
+/*
+ * SRIO_PCIE_BOOT - SLAVE
+ */
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
+               (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
+#endif
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED         10000000
+#define CONFIG_SF_DEFAULT_MODE          0
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#define CONFIG_SYS_PCIE1_MEM_VIRT      0x80000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_MEM_BUS       0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS      0xc00000000ull
+#else
+#define CONFIG_SYS_PCIE1_MEM_BUS       0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS      0x80000000
+#endif
+#define CONFIG_SYS_PCIE1_MEM_SIZE      0x20000000      /* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT       0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS                0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_IO_PHYS       0xff8000000ull
+#else
+#define CONFIG_SYS_PCIE1_IO_PHYS       0xf8000000
+#endif
+#define CONFIG_SYS_PCIE1_IO_SIZE       0x00010000      /* 64k */
+
+/* Qman/Bman */
+#ifndef CONFIG_NOBQFMAN
+#define CONFIG_SYS_DPAA_QBMAN          /* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS    25
+#define CONFIG_SYS_BMAN_MEM_BASE       0xf4000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_BMAN_MEM_PHYS       0xff4000000ull
+#else
+#define CONFIG_SYS_BMAN_MEM_PHYS       CONFIG_SYS_BMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_BMAN_MEM_SIZE       0x02000000
+#define CONFIG_SYS_QMAN_NUM_PORTALS    25
+#define CONFIG_SYS_QMAN_MEM_BASE       0xf6000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_QMAN_MEM_PHYS       0xff6000000ull
+#else
+#define CONFIG_SYS_QMAN_MEM_PHYS       CONFIG_SYS_QMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_QMAN_MEM_SIZE       0x02000000
+
+#define CONFIG_SYS_DPAA_FMAN
+
+/* Default address of microcode for the Linux Fman driver */
+#if defined(CONFIG_SPIFLASH)
+/*
+ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
+ * env, so we got 0x110000.
+ */
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_QE_FMAN_FW_ADDR     0x110000
+#elif defined(CONFIG_SDCARD)
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 545KB (1089 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_QE_FMAN_FW_ADDR     (512 * 1130)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_QE_FMAN_FW_ADDR     (6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#else
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR             0xEFF40000
+#endif
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH   0x10000
+#define CONFIG_SYS_FDT_PAD             (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+#endif /* CONFIG_NOBQFMAN */
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_TERANETICS
+#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
+#define SGMII_CARD_PORT2_PHY_ADDR 0x10
+#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
+#define SGMII_CARD_PORT4_PHY_ADDR 0x11
+#endif
+
+#ifdef CONFIG_PCI
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP                 /* do pci plug-and-play */
+#define CONFIG_E1000
+
+#define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif /* CONFIG_PCI */
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x10
+#define CONFIG_SYS_FM1_DTSEC6_PHY_ADDR 0x11
+#define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 4
+
+#define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR    0x1c
+#define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR    0x1d
+#define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR    0x1e
+#define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR    0x1f
+
+#define CONFIG_MII             /* MII PHY management */
+#define CONFIG_ETHPRIME                "FM1@DTSEC1"
+#define CONFIG_PHY_GIGE                /* Include GbE speed/duplex detection */
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_LOADS_ECHO              /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE   /* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SETEXPR
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+* USB
+*/
+#define CONFIG_HAS_FSL_DR_USB
+
+#ifdef CONFIG_HAS_FSL_DR_USB
+#define CONFIG_USB_EHCI
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+#endif
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP                    /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING                 /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE                   /* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
+#define CONFIG_SYS_PROMPT      "=> "           /* Monitor Command Prompt */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE      256             /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS     16              /* max number of command args */
+#define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ          1000            /* decrementer freq: 1ms ticks*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ   (64 << 20)      /* Initial map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH                "/opt/nfsroot"
+#define CONFIG_BOOTFILE                "uImage"
+#define CONFIG_UBOOTPATH       "u-boot.bin"    /* U-Boot image on TFTP server*/
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR                1000000
+
+#define CONFIG_BOOTDELAY       10      /* -1 disables auto-boot */
+
+#define CONFIG_BAUDRATE        115200
+
+#define __USB_PHY_TYPE ulpi
+
+#define        CONFIG_EXTRA_ENV_SETTINGS                               \
+       "hwconfig=fsl_ddr:ctlr_intlv=null,"             \
+       "bank_intlv=cs0_cs1;"                                   \
+       "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
+       "netdev=eth0\0"                                         \
+       "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"                     \
+       "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"                     \
+       "tftpflash=tftpboot $loadaddr $uboot && "               \
+       "protect off $ubootaddr +$filesize && "                 \
+       "erase $ubootaddr +$filesize && "                       \
+       "cp.b $loadaddr $ubootaddr $filesize && "               \
+       "protect on $ubootaddr +$filesize && "                  \
+       "cmp.b $loadaddr $ubootaddr $filesize\0"                \
+       "consoledev=ttyS0\0"                                    \
+       "ramdiskaddr=2000000\0"                                 \
+       "ramdiskfile=b4860qds/ramdisk.uboot\0"                  \
+       "fdtaddr=c00000\0"                                      \
+       "fdtfile=b4860qds/b4860qds.dtb\0"                               \
+       "bdev=sda3\0"                                           \
+       "c=ffe\0"
+
+/* For emulation this causes u-boot to jump to the start of the proof point
+   app code automatically */
+#define CONFIG_PROOF_POINTS                    \
+ "setenv bootargs root=/dev/$bdev rw "         \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "cpu 1 release 0x29000000 - - -;"             \
+ "cpu 2 release 0x29000000 - - -;"             \
+ "cpu 3 release 0x29000000 - - -;"             \
+ "cpu 4 release 0x29000000 - - -;"             \
+ "cpu 5 release 0x29000000 - - -;"             \
+ "cpu 6 release 0x29000000 - - -;"             \
+ "cpu 7 release 0x29000000 - - -;"             \
+ "go 0x29000000"
+
+#define CONFIG_HVBOOT  \
+ "setenv bootargs config-addr=0x60000000; "    \
+ "bootm 0x01000000 - 0x00f00000"
+
+#define CONFIG_ALU                             \
+ "setenv bootargs root=/dev/$bdev rw "         \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "cpu 1 release 0x01000000 - - -;"             \
+ "cpu 2 release 0x01000000 - - -;"             \
+ "cpu 3 release 0x01000000 - - -;"             \
+ "cpu 4 release 0x01000000 - - -;"             \
+ "cpu 5 release 0x01000000 - - -;"             \
+ "cpu 6 release 0x01000000 - - -;"             \
+ "cpu 7 release 0x01000000 - - -;"             \
+ "go 0x01000000"
+
+#define CONFIG_LINUX                           \
+ "setenv bootargs root=/dev/ram rw "           \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "setenv ramdiskaddr 0x02000000;"              \
+ "setenv fdtaddr 0x00c00000;"                  \
+ "setenv loadaddr 0x1000000;"                  \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_HDBOOT                                  \
+       "setenv bootargs root=/dev/$bdev rw "           \
+       "console=$consoledev,$baudrate $othbootargs;"   \
+       "tftp $loadaddr $bootfile;"                     \
+       "tftp $fdtaddr $fdtfile;"                       \
+       "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND                  \
+       "setenv bootargs root=/dev/nfs rw "     \
+       "nfsroot=$serverip:$rootpath "          \
+       "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+       "console=$consoledev,$baudrate $othbootargs;"   \
+       "tftp $loadaddr $bootfile;"             \
+       "tftp $fdtaddr $fdtfile;"               \
+       "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND                          \
+       "setenv bootargs root=/dev/ram rw "             \
+       "console=$consoledev,$baudrate $othbootargs;"   \
+       "tftp $ramdiskaddr $ramdiskfile;"               \
+       "tftp $loadaddr $bootfile;"                     \
+       "tftp $fdtaddr $fdtfile;"                       \
+       "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND             CONFIG_LINUX
+
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#endif
+
+#endif /* __CONFIG_H */