F: arch/mips/mach-jz47xx/
MMC
-M: Jaehoon Chung <jh80.chung@samsung.com>
+M: Peng Fan <peng.fan@nxp.com>
S: Maintained
T: git git://git.denx.de/u-boot-mmc.git
F: drivers/mmc/
am335x-evmsk.dtb \
am335x-bonegreen.dtb \
am335x-icev2.dtb \
+ am335x-pocketbeagle.dtb \
am335x-pxm50.dtb \
am335x-rut.dtb \
am335x-shc.dtb \
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Author: Robert Nelson <robertcnelson@gmail.com>
+ */
+
+/ {
+ cpus {
+ cpu@0 {
+ cpu0-supply = <&dcdc2_reg>;
+ };
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x20000000>; /* 512 MB */
+ };
+};
+
+&cpu0_opp_table {
+ /*
+ * Octavo Systems:
+ * The EFUSE_SMA register is not programmed for any of the AM335x wafers
+ * we get and we are not programming them during our production test.
+ * Therefore, from a DEVICE_ID revision point of view, the silicon looks
+ * like it is Revision 2.1. However, from an EFUSE_SMA point of view for
+ * the HW OPP table, the silicon looks like it is Revision 1.0 (ie the
+ * EFUSE_SMA register reads as all zeros).
+ */
+ oppnitro-1000000000 {
+ opp-supported-hw = <0x06 0x0100>;
+ };
+};
+
+&am33xx_pinmux {
+ i2c0_pins: pinmux-i2c0-pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) /* (C17) I2C0_SDA.I2C0_SDA */
+ AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) /* (C16) I2C0_SCL.I2C0_SCL */
+ >;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tps: tps@24 {
+ reg = <0x24>;
+ };
+};
+
+/include/ "tps65217.dtsi"
+
+&tps {
+ interrupts = <7>; /* NMI */
+ interrupt-parent = <&intc>;
+
+ ti,pmic-shutdown-controller;
+
+ pwrbutton {
+ interrupts = <2>;
+ status = "okay";
+ };
+
+ regulators {
+ dcdc1_reg: regulator@0 {
+ regulator-name = "vdds_dpr";
+ regulator-always-on;
+ };
+
+ dcdc2_reg: regulator@1 {
+ /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
+ regulator-name = "vdd_mpu";
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <1351500>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ dcdc3_reg: regulator@2 {
+ /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
+ regulator-name = "vdd_core";
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: regulator@3 {
+ regulator-name = "vio,vrtc,vdds";
+ regulator-always-on;
+ };
+
+ ldo2_reg: regulator@4 {
+ regulator-name = "vdd_3v3aux";
+ regulator-always-on;
+ };
+
+ ldo3_reg: regulator@5 {
+ regulator-name = "vdd_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo4_reg: regulator@6 {
+ regulator-name = "vdd_3v3a";
+ regulator-always-on;
+ };
+ };
+};
+
+&aes {
+ status = "okay";
+};
+
+&sham {
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Author: Robert Nelson <robertcnelson@gmail.com>
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-osd335x-common.dtsi"
+
+/ {
+ model = "TI AM335x PocketBeagle";
+ compatible = "ti,am335x-pocketbeagle", "ti,am335x-bone", "ti,am33xx";
+
+ chosen {
+ stdout-path = &uart0;
+ };
+
+ leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usr_leds_pins>;
+
+ compatible = "gpio-leds";
+
+ usr0 {
+ label = "beaglebone:green:usr0";
+ gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+
+ usr1 {
+ label = "beaglebone:green:usr1";
+ gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ default-state = "off";
+ };
+
+ usr2 {
+ label = "beaglebone:green:usr2";
+ gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "cpu0";
+ default-state = "off";
+ };
+
+ usr3 {
+ label = "beaglebone:green:usr3";
+ gpios = <&gpio1 24 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ vmmcsd_fixed: fixedregulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmcsd_fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&am33xx_pinmux {
+ i2c2_pins: pinmux-i2c2-pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x97c, PIN_INPUT_PULLUP | MUX_MODE3) /* (D17) uart1_rtsn.I2C2_SCL */
+ AM33XX_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE3) /* (D18) uart1_ctsn.I2C2_SDA */
+ >;
+ };
+
+ ehrpwm0_pins: pinmux-ehrpwm0-pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* (A13) mcasp0_aclkx.ehrpwm0A */
+ >;
+ };
+
+ ehrpwm1_pins: pinmux-ehrpwm1-pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x848, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* (U14) gpmc_a2.ehrpwm1A */
+ >;
+ };
+
+ mmc0_pins: pinmux-mmc0-pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* (C15) spi0_cs1.gpio0[6] */
+ AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0) /* (G16) mmc0_dat0.mmc0_dat0 */
+ AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0) /* (G15) mmc0_dat1.mmc0_dat1 */
+ AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0) /* (F18) mmc0_dat2.mmc0_dat2 */
+ AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0) /* (F17) mmc0_dat3.mmc0_dat3 */
+ AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0) /* (G18) mmc0_cmd.mmc0_cmd */
+ AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0) /* (G17) mmc0_clk.mmc0_clk */
+ AM33XX_IOPAD(0x9a0, PIN_INPUT | MUX_MODE4) /* (B12) mcasp0_aclkr.mmc0_sdwp */
+ >;
+ };
+
+ spi0_pins: pinmux-spi0-pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x950, PIN_INPUT_PULLUP | MUX_MODE0) /* (A17) spi0_sclk.spi0_sclk */
+ AM33XX_IOPAD(0x954, PIN_INPUT_PULLUP | MUX_MODE0) /* (B17) spi0_d0.spi0_d0 */
+ AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE0) /* (B16) spi0_d1.spi0_d1 */
+ AM33XX_IOPAD(0x95c, PIN_INPUT_PULLUP | MUX_MODE0) /* (A16) spi0_cs0.spi0_cs0 */
+ >;
+ };
+
+ spi1_pins: pinmux-spi1-pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x964, PIN_INPUT_PULLUP | MUX_MODE4) /* (C18) eCAP0_in_PWM0_out.spi1_sclk */
+ AM33XX_IOPAD(0x968, PIN_INPUT_PULLUP | MUX_MODE4) /* (E18) uart0_ctsn.spi1_d0 */
+ AM33XX_IOPAD(0x96c, PIN_INPUT_PULLUP | MUX_MODE4) /* (E17) uart0_rtsn.spi1_d1 */
+ AM33XX_IOPAD(0x9b0, PIN_INPUT_PULLUP | MUX_MODE4) /* (A15) xdma_event_intr0.spi1_cs1 */
+ >;
+ };
+
+ usr_leds_pins: pinmux-usr-leds-pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x854, PIN_OUTPUT | MUX_MODE7) /* (V15) gpmc_a5.gpio1[21] - USR_LED_0 */
+ AM33XX_IOPAD(0x858, PIN_OUTPUT | MUX_MODE7) /* (U15) gpmc_a6.gpio1[22] - USR_LED_1 */
+ AM33XX_IOPAD(0x85c, PIN_OUTPUT | MUX_MODE7) /* (T15) gpmc_a7.gpio1[23] - USR_LED_2 */
+ AM33XX_IOPAD(0x860, PIN_OUTPUT | MUX_MODE7) /* (V16) gpmc_a8.gpio1[24] - USR_LED_3 */
+ >;
+ };
+
+ uart0_pins: pinmux-uart0-pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0) /* (E15) uart0_rxd.uart0_rxd */
+ AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* (E16) uart0_txd.uart0_txd */
+ >;
+ };
+
+ uart4_pins: pinmux-uart4-pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE6) /* (T17) gpmc_wait0.uart4_rxd */
+ AM33XX_IOPAD(0x874, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* (U17) gpmc_wpn.uart4_txd */
+ >;
+ };
+};
+
+&epwmss0 {
+ status = "okay";
+};
+
+&ehrpwm0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ehrpwm0_pins>;
+};
+
+&epwmss1 {
+ status = "okay";
+};
+
+&ehrpwm1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ehrpwm1_pins>;
+};
+
+&i2c0 {
+ eeprom: eeprom@50 {
+ compatible = "atmel,24c256";
+ reg = <0x50>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+
+ status = "okay";
+ clock-frequency = <400000>;
+};
+
+&mmc1 {
+ status = "okay";
+ vmmc-supply = <&vmmcsd_fixed>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+};
+
+&rtc {
+ system-power-controller;
+};
+
+&tscadc {
+ status = "okay";
+ adc {
+ ti,adc-channels = <0 1 2 3 4 5 6 7>;
+ ti,chan-step-avg = <16 16 16 16 16 16 16 16>;
+ ti,chan-step-opendelay = <0x98 0x98 0x98 0x98 0x98 0x98 0x98 0x98>;
+ ti,chan-step-sampledelay = <0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins>;
+
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb_ctrl_mod {
+ status = "okay";
+};
+
+&usb0_phy {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "otg";
+};
+
+&usb1_phy {
+ status = "okay";
+};
+
+&usb1 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&cppi41dma {
+ status = "okay";
+};
/ {
model = "Siemens taurus";
- compatible = "atmel,at91sam9g20ek", "atmel,at91sam9g20", "atmel,at91sam9";
+ compatible = "atmel,at91sam9g20", "atmel,at91sam9";
chosen {
u-boot,dm-pre-reloc;
clock-frequency = <18432000>;
};
};
+};
- ahb {
- apb {
- pinctrl@fffff400 {
- board {
- pinctrl_pck0_as_mck: pck0_as_mck {
- atmel,pins =
- <AT91_PIOC 1 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC1 periph B */
- };
-
- };
- };
-
- dbgu: serial@fffff200 {
- u-boot,dm-pre-reloc;
- status = "okay";
- };
-
- usart0: serial@fffb0000 {
- pinctrl-0 =
- <&pinctrl_usart0
- &pinctrl_usart0_rts
- &pinctrl_usart0_cts
- &pinctrl_usart0_dtr_dsr
- &pinctrl_usart0_dcd
- &pinctrl_usart0_ri>;
- status = "okay";
- };
-
- usart1: serial@fffb4000 {
- status = "okay";
- };
-
- macb0: ethernet@fffc4000 {
- phy-mode = "rmii";
- status = "okay";
- };
-
- usb1: gadget@fffa4000 {
- atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
- status = "okay";
- };
-
- ssc0: ssc@fffbc000 {
- status = "okay";
- pinctrl-0 = <&pinctrl_ssc0_tx>;
- };
-
- spi0: spi@fffc8000 {
- cs-gpios = <0>, <&pioC 11 0>, <0>, <0>;
- mtd_dataflash@0 {
- compatible = "atmel,at45", "atmel,dataflash";
- spi-max-frequency = <50000000>;
- reg = <1>;
- };
- };
-
- rtc@fffffd20 {
- atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
- status = "okay";
- };
-
- watchdog@fffffd40 {
- timeout-sec = <15>;
- status = "okay";
- };
-
- gpbr: syscon@fffffd50 {
- status = "okay";
- };
- };
+&dbgu {
+ status = "okay";
+};
- nand0: nand@40000000 {
- nand-bus-width = <8>;
- nand-ecc-mode = "soft";
- nand-on-flash-bbt;
- status = "okay";
- };
+&gpbr {
+ status = "okay";
+};
+
+&macb0 {
+ phy-mode = "rmii";
+ status = "okay";
+};
- usb0: ohci@00500000 {
- num-ports = <2>;
- status = "okay";
+&nand0 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt;
+ status = "okay";
+};
+
+&pinctrl {
+ u-boot,dm-pre-reloc;
+ board {
+ pinctrl_pck0_as_mck: pck0_as_mck {
+ atmel,pins =
+ /* PC1 periph B */
+ <AT91_PIOC 1 AT91_PERIPH_B AT91_PINCTRL_NONE>;
};
+
};
};
+
+&rtc {
+ atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+ status = "okay";
+};
+
+&spi0 {
+ cs-gpios = <0>, <&pioC 11 0>, <0>, <0>;
+ mtd_dataflash@0 {
+ compatible = "atmel,at45", "atmel,dataflash";
+ spi-max-frequency = <50000000>;
+ reg = <1>;
+ };
+};
+
+&ssc0 {
+ status = "okay";
+ pinctrl-0 = <&pinctrl_ssc0_tx>;
+};
+
+&usart0 {
+ pinctrl-0 =
+ <&pinctrl_usart0
+ &pinctrl_usart0_rts
+ &pinctrl_usart0_cts
+ &pinctrl_usart0_dtr_dsr
+ &pinctrl_usart0_dcd
+ &pinctrl_usart0_ri>;
+ status = "okay";
+};
+
+&usart1 {
+ status = "okay";
+};
+
+&usb0 {
+ num-ports = <2>;
+ status = "okay";
+};
+
+&usb1 {
+ atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&watchdog {
+ u-boot,dm-pre-reloc;
+ timeout-sec = <15>;
+ status = "okay";
+};
* Copyright (C) 2018 Texas Instruments Incorporated - http://www.ti.com/
*/
-#include <dt-bindings/pinctrl/k3-am65.h>
+#include <dt-bindings/pinctrl/k3.h>
#include <dt-bindings/dma/k3-udma.h>
/ {
u-boot,dm-spl;
main_uart0_pins_default: main_uart0_pins_default {
pinctrl-single,pins = <
- AM65X_IOPAD(0x01e4, PIN_INPUT | MUX_MODE0) /* (AF11) UART0_RXD */
- AM65X_IOPAD(0x01e8, PIN_OUTPUT | MUX_MODE0) /* (AE11) UART0_TXD */
- AM65X_IOPAD(0x01ec, PIN_INPUT | MUX_MODE0) /* (AG11) UART0_CTSn */
- AM65X_IOPAD(0x01f0, PIN_OUTPUT | MUX_MODE0) /* (AD11) UART0_RTSn */
+ AM65X_IOPAD(0x01e4, PIN_INPUT, 0) /* (AF11) UART0_RXD */
+ AM65X_IOPAD(0x01e8, PIN_OUTPUT, 0) /* (AE11) UART0_TXD */
+ AM65X_IOPAD(0x01ec, PIN_INPUT, 0) /* (AG11) UART0_CTSn */
+ AM65X_IOPAD(0x01f0, PIN_OUTPUT, 0) /* (AD11) UART0_RTSn */
>;
u-boot,dm-spl;
};
main_mmc0_pins_default: main_mmc0_pins_default {
pinctrl-single,pins = <
- AM65X_IOPAD(0x01a8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* (B25) MMC0_CLK */
- AM65X_IOPAD(0x01aC, PIN_INPUT_PULLUP | MUX_MODE0) /* (B27) MMC0_CMD */
- AM65X_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* (A26) MMC0_DAT0 */
- AM65X_IOPAD(0x01a0, PIN_INPUT_PULLUP | MUX_MODE0) /* (E25) MMC0_DAT1 */
- AM65X_IOPAD(0x019c, PIN_INPUT_PULLUP | MUX_MODE0) /* (C26) MMC0_DAT2 */
- AM65X_IOPAD(0x0198, PIN_INPUT_PULLUP | MUX_MODE0) /* (A25) MMC0_DAT3 */
- AM65X_IOPAD(0x0194, PIN_INPUT_PULLUP | MUX_MODE0) /* (E24) MMC0_DAT4 */
- AM65X_IOPAD(0x0190, PIN_INPUT_PULLUP | MUX_MODE0) /* (A24) MMC0_DAT5 */
- AM65X_IOPAD(0x018c, PIN_INPUT_PULLUP | MUX_MODE0) /* (B26) MMC0_DAT6 */
- AM65X_IOPAD(0x0188, PIN_INPUT_PULLUP | MUX_MODE0) /* (D25) MMC0_DAT7 */
- AM65X_IOPAD(0x01b0, PIN_INPUT | MUX_MODE0) /* (C25) MMC0_DS */
+ AM65X_IOPAD(0x01a8, PIN_INPUT_PULLDOWN, 0) /* (B25) MMC0_CLK */
+ AM65X_IOPAD(0x01aC, PIN_INPUT_PULLUP, 0) /* (B27) MMC0_CMD */
+ AM65X_IOPAD(0x01a4, PIN_INPUT_PULLUP, 0) /* (A26) MMC0_DAT0 */
+ AM65X_IOPAD(0x01a0, PIN_INPUT_PULLUP, 0) /* (E25) MMC0_DAT1 */
+ AM65X_IOPAD(0x019c, PIN_INPUT_PULLUP, 0) /* (C26) MMC0_DAT2 */
+ AM65X_IOPAD(0x0198, PIN_INPUT_PULLUP, 0) /* (A25) MMC0_DAT3 */
+ AM65X_IOPAD(0x0194, PIN_INPUT_PULLUP, 0) /* (E24) MMC0_DAT4 */
+ AM65X_IOPAD(0x0190, PIN_INPUT_PULLUP, 0) /* (A24) MMC0_DAT5 */
+ AM65X_IOPAD(0x018c, PIN_INPUT_PULLUP, 0) /* (B26) MMC0_DAT6 */
+ AM65X_IOPAD(0x0188, PIN_INPUT_PULLUP, 0) /* (D25) MMC0_DAT7 */
+ AM65X_IOPAD(0x01b0, PIN_INPUT, 0) /* (C25) MMC0_DS */
>;
u-boot,dm-spl;
};
main_mmc1_pins_default: main_mmc1_pins_default {
pinctrl-single,pins = <
- AM65X_IOPAD(0x02d4, PIN_INPUT_PULLDOWN | MUX_MODE0) /* (C27) MMC1_CLK */
- AM65X_IOPAD(0x02d8, PIN_INPUT_PULLUP | MUX_MODE0) /* (C28) MMC1_CMD */
- AM65X_IOPAD(0x02d0, PIN_INPUT_PULLUP | MUX_MODE0) /* (D28) MMC1_DAT0 */
- AM65X_IOPAD(0x02cc, PIN_INPUT_PULLUP | MUX_MODE0) /* (E27) MMC1_DAT1 */
- AM65X_IOPAD(0x02c8, PIN_INPUT_PULLUP | MUX_MODE0) /* (D26) MMC1_DAT2 */
- AM65X_IOPAD(0x02c4, PIN_INPUT_PULLUP | MUX_MODE0) /* (D27) MMC1_DAT3 */
- AM65X_IOPAD(0x02dc, PIN_INPUT_PULLUP | MUX_MODE0) /* (B24) MMC1_SDCD */
- AM65X_IOPAD(0x02e0, PIN_INPUT | MUX_MODE0) /* (C24) MMC1_SDWP */
+ AM65X_IOPAD(0x02d4, PIN_INPUT_PULLDOWN, 0) /* (C27) MMC1_CLK */
+ AM65X_IOPAD(0x02d8, PIN_INPUT_PULLUP, 0) /* (C28) MMC1_CMD */
+ AM65X_IOPAD(0x02d0, PIN_INPUT_PULLUP, 0) /* (D28) MMC1_DAT0 */
+ AM65X_IOPAD(0x02cc, PIN_INPUT_PULLUP, 0) /* (E27) MMC1_DAT1 */
+ AM65X_IOPAD(0x02c8, PIN_INPUT_PULLUP, 0) /* (D26) MMC1_DAT2 */
+ AM65X_IOPAD(0x02c4, PIN_INPUT_PULLUP, 0) /* (D27) MMC1_DAT3 */
+ AM65X_IOPAD(0x02dc, PIN_INPUT_PULLUP, 0) /* (B24) MMC1_SDCD */
+ AM65X_IOPAD(0x02e0, PIN_INPUT, 0) /* (C24) MMC1_SDWP */
>;
u-boot,dm-spl;
};
};
&dmsc {
- mboxes= <&mcu_secproxy 7>, <&mcu_secproxy 6>, <&mcu_secproxy 5>;
+ mboxes= <&mcu_secproxy 8>, <&mcu_secproxy 6>, <&mcu_secproxy 5>;
mbox-names = "tx", "rx", "notify";
ti,host-id = <4>;
ti,secure-host;
u-boot,dm-spl;
wkup_uart0_pins_default: wkup_uart0_pins_default {
pinctrl-single,pins = <
- AM65X_WKUP_IOPAD(0x00a0, PIN_INPUT | MUX_MODE0) /* (AB1) WKUP_UART0_RXD */
- AM65X_WKUP_IOPAD(0x00a4, PIN_OUTPUT | MUX_MODE0) /* (AB5) WKUP_UART0_TXD */
- AM65X_WKUP_IOPAD(0x00c8, PIN_INPUT | MUX_MODE1) /* (AC2) WKUP_GPIO0_6.WKUP_UART0_CTSn */
- AM65X_WKUP_IOPAD(0x00cc, PIN_OUTPUT | MUX_MODE1) /* (AC1) WKUP_GPIO0_7.WKUP_UART0_RTSn */
+ AM65X_WKUP_IOPAD(0x00a0, PIN_INPUT, 0) /* (AB1) WKUP_UART0_RXD */
+ AM65X_WKUP_IOPAD(0x00a4, PIN_OUTPUT, 0) /* (AB5) WKUP_UART0_TXD */
+ AM65X_WKUP_IOPAD(0x00c8, PIN_INPUT, 1) /* (AC2) WKUP_GPIO0_6.WKUP_UART0_CTSn */
+ AM65X_WKUP_IOPAD(0x00cc, PIN_OUTPUT, 1) /* (AC1) WKUP_GPIO0_7.WKUP_UART0_RTSn */
>;
u-boot,dm-spl;
};
wkup_vtt_pins_default: wkup_vtt_pins_default {
pinctrl-single,pins = <
- AM65X_WKUP_IOPAD(0x0040, PIN_OUTPUT_PULLUP | MUX_MODE7) /* WKUP_GPIO0_28 */
+ AM65X_WKUP_IOPAD(0x0040, PIN_OUTPUT_PULLUP, 7) /* WKUP_GPIO0_28 */
>;
u-boot,dm-spl;
};
interrupts-extended = <&intc 83 &omap3_pmx_core 0x11a>;
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins>;
- wp-gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>; /* gpio_126 */
- cd-gpios = <&gpio4 14 IRQ_TYPE_LEVEL_LOW>; /* gpio_110 */
+ wp-gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>; /* gpio_126 */
+ cd-gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* gpio_110 */
vmmc-supply = <&vmmc1>;
bus-width = <4>;
cap-power-off-card;
config SYS_CONFIG_NAME
default "taurus"
+choice
+ prompt "Board Type AXM/TAURUS"
+ default BOARD_AXM
+
+config BOARD_AXM
+ bool "AXM board type"
+ help
+ Select this, if you want to build for AXM board.
+
+config BOARD_TAURUS
+ bool "TAURUS board type"
+ help
+ Select this, if you want to build for TAURUS board.
+
+endchoice
+
endif
/* Mirrors at A15 on ATMEL G20 SDRAM Controller with 64MB*/
if (ram_size == 0x800) {
- printf("\n\r 64MB");
+ printf("\n\r 64MB\n");
sdramc_configure(AT91_SDRAMC_NC_9);
} else {
/* Size already initialized */
- printf("\n\r 128MB");
+ printf("\n\r 128MB\n");
}
}
#endif
return 0;
}
-/* FIXME gpio code here need to handle through DM_GPIO */
-#ifndef CONFIG_DM_SPI
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
- return bus == 0 && cs == 0;
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
- at91_set_gpio_value(TAURUS_SPI_CS_PIN, 0);
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
- at91_set_gpio_value(TAURUS_SPI_CS_PIN, 1);
-}
-#endif
-
#ifdef CONFIG_USB_GADGET_AT91
#include <linux/usb/at91_udc.h>
return 0;
}
-#ifndef CONFIG_DM_ETH
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_MACB
- rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, 0x00);
-#endif
- return rc;
-}
-#endif
-
#if !defined(CONFIG_SPL_BUILD)
#if defined(CONFIG_BOARD_AXM)
/*
configure_module_pin_mux(mii1_pin_mux);
}
/* Beaglebone LT pinmux */
- configure_module_pin_mux(mii1_pin_mux);
configure_module_pin_mux(mmc0_pin_mux);
#if defined(CONFIG_NAND) && defined(CONFIG_EMMC_BOOT)
configure_module_pin_mux(nand_pin_mux);
# CONFIG_SPL_EFI_PARTITION is not set
CONFIG_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="am335x-evm"
-CONFIG_OF_LIST="am335x-evm am335x-bone am335x-boneblack am335x-evmsk am335x-bonegreen am335x-icev2"
+CONFIG_OF_LIST="am335x-evm am335x-bone am335x-boneblack am335x-evmsk am335x-bonegreen am335x-icev2 am335x-pocketbeagle"
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_SPL_ENV_IS_NOWHERE=y
CONFIG_BOOTCOUNT_LIMIT=y
CONFIG_ARM=y
-CONFIG_SPL_SYS_THUMB_BUILD=y
+CONFIG_SYS_THUMB_BUILD=y
# CONFIG_SPL_USE_ARCH_MEMCPY is not set
# CONFIG_SPL_USE_ARCH_MEMSET is not set
CONFIG_ARCH_AT91=y
+CONFIG_SPL_LDSCRIPT="arch/$(ARCH)/cpu/u-boot-spl.lds"
CONFIG_SYS_TEXT_BASE=0x21000000
CONFIG_TARGET_TAURUS=y
CONFIG_SPL_GPIO_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_SPL_SYS_MALLOC_F_LEN=0x1000
CONFIG_NR_DRAM_BANKS=1
CONFIG_SPL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=18432000
CONFIG_SPL_SPI_FLASH_SUPPORT=y
CONFIG_SPL_SPI_SUPPORT=y
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,MACH_TYPE=2068,BOARD_AXM"
+CONFIG_DEBUG_UART=y
+CONFIG_TPL_SYS_MALLOC_F_LEN=0x1000
+CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,MACH_TYPE=2068"
CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="\0addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:${netdev}::off\0addtest=setenv bootargs ${bootargs} loglevel=4 test\0baudrate=115200\0boot_file=setenv bootfile /${project_dir}/kernel/uImage\0boot_retries=0\0bootcmd=run flash_self\0bootdelay=3\0ethact=macb0\0flash_nfs=run nand_kernel;run nfsargs;run addip;upgrade_available;bootm ${kernel_ram};reset\0flash_self=run nand_kernel;run setbootargs;upgrade_available;bootm ${kernel_ram};reset\0flash_self_test=run nand_kernel;run setbootargs addtest; upgrade_available;bootm ${kernel_ram};reset\0hostname=systemone\0kernel_Off=0x00200000\0kernel_Off_fallback=0x03800000\0kernel_ram=0x21500000\0kernel_size=0x00400000\0kernel_size_fallback=0x00400000\0loads_echo=1\0nand_kernel=nand read.e ${kernel_ram} ${kernel_Off} ${kernel_size}\0net_nfs=run boot_file;tftp ${kernel_ram} ${bootfile};run nfsargs;run addip;upgrade_available;bootm ${kernel_ram};reset\0netdev=eth0\0nfsargs=run root_path;setenv bootargs ${bootargs} root=/dev/nfs rw nfsroot=${serverip}:${rootpath} at91sam9_wdt.wdt_timeout=16\0partitionset_active=A\0preboot=echo;echo Type 'run flash_self' to use kernel and root filesystem on memory;echo Type 'run flash_nfs' to use kernel from memory and root filesystem over NFS;echo Type 'run net_nfs' to get Kernel over TFTP and mount root filesystem over NFS;echo\0project_dir=systemone\0root_path=setenv rootpath /home/projects/${project_dir}/rootfs\0rootfs=/dev/mtdblock5\0rootfs_fallback=/dev/mtdblock7\0setbootargs=setenv bootargs ${bootargs} console=ttyMTD,mtdoops root=${rootfs} rootfstype=jffs2 panic=7 at91sam9_wdt.wdt_timeout=16\0stderr=serial\0stdin=serial\0stdout=serial\0upgrade_available=0\0"
+CONFIG_USE_BOOTCOMMAND=y
+CONFIG_BOOTCOMMAND="run flash_self"
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_BOARD_EARLY_INIT_F=y
+# CONFIG_SPL_LEGACY_IMAGE_SUPPORT is not set
+CONFIG_SPL_SYS_MALLOC_SIMPLE=y
+# CONFIG_TPL_BANNER_PRINT is not set
+CONFIG_SPL_CRC32_SUPPORT=y
CONFIG_SPL_NAND_SUPPORT=y
-CONFIG_SPL_SPI_LOAD=y
CONFIG_HUSH_PARSER=y
+CONFIG_SYS_PROMPT="U-Boot> "
# CONFIG_CMD_BDI is not set
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_IMI is not set
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_NAND=y
+# CONFIG_CMD_PINMUX is not set
CONFIG_CMD_SF=y
CONFIG_CMD_SPI=y
# CONFIG_CMD_SOURCE is not set
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
+CONFIG_CMD_MTDPARTS=y
CONFIG_OF_CONTROL=y
-CONFIG_OF_EMBED=y
+CONFIG_SPL_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9g20-taurus"
+CONFIG_SPL_OF_PLATDATA=y
CONFIG_ENV_IS_IN_NAND=y
+CONFIG_SPL_DM=y
+CONFIG_BLK=y
+CONFIG_HAVE_BLOCK_DEVICE=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
# CONFIG_MMC is not set
CONFIG_NAND=y
CONFIG_NAND_ATMEL=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_SPECIFY_CONSOLE_INDEX=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_ATMEL_USART=y
+CONFIG_WDT=y
+CONFIG_WDT_AT91=y
CONFIG_USE_TINY_PRINTF=y
+CONFIG_HEXDUMP=y
+# CONFIG_EFI_LOADER is not set
CONFIG_ARM=y
-CONFIG_SPL_SYS_THUMB_BUILD=y
+CONFIG_SYS_THUMB_BUILD=y
# CONFIG_SPL_USE_ARCH_MEMCPY is not set
# CONFIG_SPL_USE_ARCH_MEMSET is not set
CONFIG_ARCH_AT91=y
CONFIG_SPL_LDSCRIPT="arch/$(ARCH)/cpu/u-boot-spl.lds"
CONFIG_SYS_TEXT_BASE=0x21000000
CONFIG_TARGET_TAURUS=y
+CONFIG_BOARD_TAURUS=y
CONFIG_SPL_GPIO_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_SYS_MALLOC_F_LEN=0x1000
-CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_SPL_SYS_MALLOC_F_LEN=0x1000
CONFIG_NR_DRAM_BANKS=1
CONFIG_SPL=y
+CONFIG_DEBUG_UART_BASE=0xfffff200
+CONFIG_DEBUG_UART_CLOCK=18432000
CONFIG_SPL_SPI_FLASH_SUPPORT=y
CONFIG_SPL_SPI_SUPPORT=y
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,MACH_TYPE=2067,BOARD_TAURUS"
+CONFIG_DEBUG_UART=y
+CONFIG_TPL_SYS_MALLOC_F_LEN=0x1000
+CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G20,MACH_TYPE=2067"
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,256k(env),256k(env_redundant),256k(spare),512k(dtb),6M(kernel)ro,-(rootfs) root=/dev/mtdblock7 rw rootfstype=jffs2"
+CONFIG_USE_BOOTCOMMAND=y
+CONFIG_BOOTCOMMAND="nand read 0x22000000 0x200000 0x300000; bootm"
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_BOARD_EARLY_INIT_F=y
+# CONFIG_SPL_LEGACY_IMAGE_SUPPORT is not set
+CONFIG_SPL_SYS_MALLOC_SIMPLE=y
+# CONFIG_TPL_BANNER_PRINT is not set
+CONFIG_SPL_CRC32_SUPPORT=y
CONFIG_SPL_NAND_SUPPORT=y
-CONFIG_SPL_SPI_LOAD=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot> "
+CONFIG_SYS_XTRACE="n"
# CONFIG_CMD_BDI is not set
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_IMI is not set
CONFIG_CMD_DFU=y
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_NAND=y
+# CONFIG_CMD_PINMUX is not set
CONFIG_CMD_SF=y
CONFIG_CMD_SPI=y
CONFIG_CMD_USB=y
CONFIG_CMD_MTDPARTS=y
# CONFIG_DOS_PARTITION is not set
CONFIG_OF_CONTROL=y
-CONFIG_OF_EMBED=y
+CONFIG_SPL_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="at91sam9g20-taurus"
+CONFIG_SPL_OF_PLATDATA=y
CONFIG_ENV_IS_IN_NAND=y
+CONFIG_SPL_DM=y
+CONFIG_BLK=y
CONFIG_CLK=y
CONFIG_CLK_AT91=y
CONFIG_DFU_NAND=y
# CONFIG_MMC is not set
CONFIG_NAND=y
CONFIG_NAND_ATMEL=y
+CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_SPECIFY_CONSOLE_INDEX=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_ATMEL_USART=y
CONFIG_USB=y
+CONFIG_DM_USB=y
+# CONFIG_SPL_DM_USB is not set
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_MANUFACTURER="Siemens AG"
CONFIG_WDT=y
CONFIG_WDT_AT91=y
CONFIG_USE_TINY_PRINTF=y
+CONFIG_HEXDUMP=y
+# CONFIG_EFI_LOADER is not set
Summary
=======
-This README is about U-Boot support for TI's ARM 926EJS based family of SoCs.
-These SOCs are used for cameras, video security and surveillance, DVR's, etc.
-DaVinci SOC's comprise of DM644x, DM646x, DM35x and DM36x series of SOC's
-Additionally there are some SOCs meant for the audio market which though have
-an OMAP part number are very similar to the DaVinci series of SOC's
-Additionally, some family members contain a TI DSP and/or graphics
-co processors along with a host of other peripherals.
+Note: this document used to be about the entire family of DaVinci SOCs but the
+support for the DM* family and DA830 has since been dropped.
-Currently the following boards are supported:
-
-* TI DaVinci DM644x EVM
-
-* TI DaVinci DM646x EVM
-
-* TI DaVinci DM355 EVM
-
-* TI DaVinci DM365 EVM
+This README is about U-Boot support for TI's DA850 SoC. This SOC has an OMAP
+part number but is very similar to the DaVinci series.
-* TI DA830 EVM
+Currently the following boards are supported:
* TI DA850 EVM
-* DM355 based Leopard board
-
-* DM644x based schmoogie board
-
-* DM644x based sffsdr board
+* TI OMAP-L138 LCDK
-* DM644x based sonata board
+* Lego EV3
Build
=====
-* TI DaVinci DM644x EVM:
-
-make davinci_dvevm_config
-make
-
-* TI DaVinci DM646x EVM:
-
-make davinci_dm6467evm_config
-make
-
-* TI DaVinci DM355 EVM:
-
-make davinci_dm355evm_config
-make
-
-* TI DaVinci DM365 EVM:
-
-make davinci_dm365evm_config
-make
-
-* TI DA830 EVM:
-
-make da830evm_config
-make
-
* TI DA850 EVM:
make da850evm_config
make
-* DM355 based Leopard board:
-
-make davinci_dm355leopard_config
-make
-
-* DM644x based schmoogie board:
+* TI OMAP-L138 LCDK
-make davinci_schmoogie_config
+make omapl138_lcdk_defconfig
make
-* DM644x based sffsdr board:
+* Lego EV3
-make davinci_sffsdr_config
-make
-
-* DM644x based sonata board:
-
-make davinci_sonata_config
+make legoev3_defconfig
make
Bootloaders
===============
-The DaVinci SOC's use 2 bootloaders. The low level initialization
-is done by a UBL(user boot loader). The UBL is written to a NAND/NOR/SPI flash
-by a programmer. During initial bootup, the ROM Bootloader reads the UBL
-from a storage device and loads it into the IRAM. The UBL then loads the U-Boot
-into the RAM.
-The programmers and UBL are always released as part of any standard TI
-software release associated with an SOC.
-
-Alternative boot method (DA850 EVM only):
-For the DA850 EVM an SPL (secondary program loader, see doc/README.SPL)
-is provided to load U-Boot directly from SPI flash. In this case, the
-SPL does the low level initialization that is otherwise done by the SPL.
-To build U-Boot with this SPL, do
-make da850evm_config
-make u-boot.ais
-and program the resulting u-boot.ais file to the SPI flash of the DA850 EVM.
+For DA850 an SPL (secondary program loader, see doc/README.SPL) is provided
+to load U-Boot directly from SPI flash. The SPL takes care of the low level
+initialization.
+
+The SPL is built as u-boot.ais for all DA850 defconfigs. The resulting
+image file can be programmed to the SPI flash of the DA850 EVM/LCDK.
Environment Variables
=====================
Links
=====
-1) TI DaVinci DM355 EVM:
-http://focus.ti.com/docs/prod/folders/print/tms320dm355.html
-http://www.spectrumdigital.com/product_info.php?cPath=103&products_id=203&osCsid=c499af6087317f11b3da19b4e8f1af32
-
-2) TI DaVinci DM365 EVM:
-http://focus.ti.com/docs/prod/folders/print/tms320dm365.html?247SEM=
-http://support.spectrumdigital.com/boards/evmdm365/revc/
-
-3) DaVinci DM355 based leopard board
-http://designsomething.org/leopardboard/default.aspx
-http://www.spectrumdigital.com/product_info.php?cPath=103&products_id=192&osCsid=67c20335668ffc57cb35727106eb24b1
-
-4) TI DaVinci DM6467 EVM:
-http://focus.ti.com/docs/prod/folders/print/tms320dm6467.html
-http://support.spectrumdigital.com/boards/evmdm6467/revf/
-
-5) TI DaVinci DM6446 EVM:
-http://focus.ti.com/docs/prod/folders/print/tms320dm6446.html
-http://www.spectrumdigital.com/product_info.php?cPath=103&products_id=222
-
-6) TI DA830 EVM
-http://focus.ti.com/apps/docs/gencontent.tsp?appId=1&contentId=52385
-http://www.spectrumdigital.com/product_info.php?cPath=37&products_id=214
-
-7) TI DA850 EVM
+1) TI DA850 EVM
http://focus.ti.com/docs/prod/folders/print/omap-l138.html
http://www.logicpd.com/products/development-kits/zoom-omap-l138-evm-development-kit
+2) TI OMAP-L138 LCDK
+http://focus.ti.com/docs/prod/folders/print/omap-l138.html
+http://www.ti.com/tool/TMDXLCDK138
+
Davinci special defines
=======================
alias danielschwierzeck Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
alias dinh Dinh Nguyen <dinguyen@kernel.org>
alias hs Heiko Schocher <hs@denx.de>
+alias freenix Peng Fan <peng.fan@nxp.com>
alias iwamatsu Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
alias jaehoon Jaehoon Chung <jh80.chung@samsung.com>
alias jagan Jagan Teki <jagan@amarulasolutions.com>
alias fdt uboot, sjg
alias i2c uboot, hs
alias kconfig uboot, masahiro
-alias mmc uboot, jaehoon
+alias mmc uboot, freenix
alias nand uboot
alias net uboot, jhersh
alias phy uboot, jhersh
pr_debug("chan%d: got tchan%d\n", uc->id, uc->tchan->id);
- if (udma_is_chan_running(uc)) {
- dev_warn(ud->dev, "chan%d: tchan%d is running!\n", uc->id,
- uc->tchan->id);
- udma_stop(uc);
- if (udma_is_chan_running(uc))
- dev_err(ud->dev, "chan%d: won't stop!\n", uc->id);
- }
-
return 0;
}
pr_debug("chan%d: got rchan%d\n", uc->id, uc->rchan->id);
- if (udma_is_chan_running(uc)) {
- dev_warn(ud->dev, "chan%d: rchan%d is running!\n", uc->id,
- uc->rchan->id);
- udma_stop(uc);
- if (udma_is_chan_running(uc))
- dev_err(ud->dev, "chan%d: won't stop!\n", uc->id);
- }
-
return 0;
}
pr_debug("chan%d: got t/rchan%d pair\n", uc->id, chan_id);
- if (udma_is_chan_running(uc)) {
- dev_warn(ud->dev, "chan%d: t/rchan%d pair is running!\n",
- uc->id, chan_id);
- udma_stop(uc);
- if (udma_is_chan_running(uc))
- dev_err(ud->dev, "chan%d: won't stop!\n", uc->id);
- }
-
return 0;
}
}
}
+ if (udma_is_chan_running(uc)) {
+ dev_warn(ud->dev, "chan%d: is running!\n", uc->id);
+ udma_stop(uc);
+ if (udma_is_chan_running(uc)) {
+ dev_err(ud->dev, "chan%d: won't stop!\n", uc->id);
+ goto err_free_res;
+ }
+ }
+
/* PSI-L pairing */
ret = udma_navss_psil_pair(ud, uc->src_thread, uc->dst_thread);
if (ret) {
u32 tc_ring_id;
int ret;
- if (!metadata)
+ if (metadata)
packet_data = *((struct ti_udma_drv_packet_data *)metadata);
if (dma->id >= (ud->rchan_cnt + ud->tchan_cnt)) {
int ret;
/* Receive the response */
- ret = mbox_recv(chan, msg, info->desc->max_rx_timeout_ms);
+ ret = mbox_recv(chan, msg, info->desc->max_rx_timeout_ms * 1000);
if (ret) {
dev_err(info->dev, "%s: Message receive failed. ret = %d\n",
__func__, ret);
info = handle_to_ti_sci_info(handle);
- xfer = ti_sci_setup_one_xfer(info, TI_SCI_MSG_VERSION, 0x0,
+ xfer = ti_sci_setup_one_xfer(info, TI_SCI_MSG_VERSION,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
(u32 *)&hdr, sizeof(struct ti_sci_msg_hdr),
sizeof(*rev_info));
if (IS_ERR(xfer)) {
info = handle_to_ti_sci_info(handle);
- /* Response is expected, so need of any flags */
- xfer = ti_sci_setup_one_xfer(info, TI_SCI_MSG_GET_DEVICE_STATE, 0,
+ xfer = ti_sci_setup_one_xfer(info, TI_SCI_MSG_GET_DEVICE_STATE,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
(u32 *)&req, sizeof(req), sizeof(*resp));
if (IS_ERR(xfer)) {
ret = PTR_ERR(xfer);
info = handle_to_ti_sci_info(handle);
- xfer = ti_sci_setup_one_xfer(info, TISCI_MSG_FWL_GET,
- TISCI_MSG_FWL_CHANGE_OWNER,
+ xfer = ti_sci_setup_one_xfer(info, TISCI_MSG_FWL_CHANGE_OWNER,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
(u32 *)&req, sizeof(req), sizeof(*resp));
if (IS_ERR(xfer)) {
ret = PTR_ERR(xfer);
help
Enable driver model for watchdog timer. At the moment the API
is very simple and only supports four operations:
- start, restart, stop and reset (expire immediately).
+ start, stop, reset and expire_now (expire immediately).
What exactly happens when the timer expires is up to a particular
device/driver.
if (inr == -1ULL) {
printf("Cannot lookup path %s\n", path);
- return 1;
+ return -1;
}
if (type != BTRFS_FT_DIR) {
printf("Not a directory: %s\n", path);
- return 1;
+ return -1;
}
if (btrfs_readdir(&root, inr, readdir_callback)) {
printf("An error occured while listing directory %s\n", path);
- return 1;
+ return -1;
}
return 0;
if (inr == -1ULL) {
printf("Cannot lookup file %s\n", file);
- return 1;
+ return -1;
}
if (type != BTRFS_FT_REG_FILE) {
printf("Not a regular file: %s\n", file);
- return 1;
+ return -1;
}
*size = inode.size;
if (inr == -1ULL) {
printf("Cannot lookup file %s\n", file);
- return 1;
+ return -1;
}
if (type != BTRFS_FT_REG_FILE) {
printf("Not a regular file: %s\n", file);
- return 1;
+ return -1;
}
if (!len)
rd = btrfs_file_read(&root, inr, offset, len, buf);
if (rd == -1ULL) {
printf("An error occured while reading file %s\n", file);
- return 1;
+ return -1;
}
*actread = rd;
break;
if (btrfs_check_super_csum(raw_sb)) {
- printf("%s: invalid checksum at superblock mirror %i\n",
- __func__, i);
+ debug("%s: invalid checksum at superblock mirror %i\n",
+ __func__, i);
continue;
}
btrfs_super_block_to_cpu(sb);
if (sb->magic != BTRFS_MAGIC) {
- printf("%s: invalid BTRFS magic 0x%016llX at "
- "superblock mirror %i\n", __func__, sb->magic,
- i);
+ debug("%s: invalid BTRFS magic 0x%016llX at "
+ "superblock mirror %i\n", __func__, sb->magic, i);
} else if (sb->bytenr != superblock_offsets[i]) {
printf("%s: invalid bytenr 0x%016llX (expected "
"0x%016llX) at superblock mirror %i\n",
}
if (!btrfs_info.sb.generation) {
- printf("%s: No valid BTRFS superblock found!\n", __func__);
+ debug("%s: No valid BTRFS superblock found!\n", __func__);
return -1;
}
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
+
#define CONFIG_SKIP_LOWLEVEL_INIT_ONLY
/* general purpose I/O */
#define CONFIG_AT91_GPIO
#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */
-/* serial console */
-#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE ATMEL_BASE_DBGU
#define CONFIG_USART_ID ATMEL_ID_SYS
-
/*
* SDRAM: 1 bank, min 32, max 128 MB
* Initialized before u-boot gets started.
/* SPI EEPROM */
#define TAURUS_SPI_MASK (1 << 4)
-#define TAURUS_SPI_CS_PIN AT91_PIN_PA3
#if defined(CONFIG_SPL_BUILD)
/* SPL related */
#define CONFIG_ENV_OFFSET 0x100000
#define CONFIG_ENV_OFFSET_REDUND 0x180000
#define CONFIG_ENV_SIZE (SZ_128K) /* 1 sector = 128 kB */
-#define CONFIG_BOOTCOMMAND "nand read 0x22000000 0x200000 0x300000; bootm"
+#ifndef CONFIG_SPL_BUILD
+#if defined(CONFIG_BOARD_AXM)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:" \
+ "${gatewayip}:${netmask}:${hostname}:${netdev}::off\0" \
+ "addtest=setenv bootargs ${bootargs} loglevel=4 test\0" \
+ "boot_file=setenv bootfile /${project_dir}/kernel/uImage\0" \
+ "boot_retries=0\0" \
+ "ethact=macb0\0" \
+ "flash_nfs=run nand_kernel;run nfsargs;run addip;" \
+ "upgrade_available;bootm ${kernel_ram};reset\0" \
+ "flash_self=run nand_kernel;run setbootargs;upgrade_available;" \
+ "bootm ${kernel_ram};reset\0" \
+ "flash_self_test=run nand_kernel;run setbootargs addtest;" \
+ "upgrade_available;bootm ${kernel_ram};reset\0" \
+ "hostname=systemone\0" \
+ "kernel_Off=0x00200000\0" \
+ "kernel_Off_fallback=0x03800000\0" \
+ "kernel_ram=0x21500000\0" \
+ "kernel_size=0x00400000\0" \
+ "kernel_size_fallback=0x00400000\0" \
+ "loads_echo=1\0" \
+ "nand_kernel=nand read.e ${kernel_ram} ${kernel_Off} " \
+ "${kernel_size}\0" \
+ "net_nfs=run boot_file;tftp ${kernel_ram} ${bootfile};" \
+ "run nfsargs;run addip;upgrade_available;" \
+ "bootm ${kernel_ram};reset\0" \
+ "netdev=eth0\0" \
+ "nfsargs=run root_path;setenv bootargs ${bootargs} root=/dev/nfs " \
+ "rw nfsroot=${serverip}:${rootpath} " \
+ "at91sam9_wdt.wdt_timeout=16\0" \
+ "partitionset_active=A\0" \
+ "preboot=echo;echo Type 'run flash_self' to use kernel and root " \
+ "filesystem on memory;echo Type 'run flash_nfs' to use " \
+ "kernel from memory and root filesystem over NFS;echo Type " \
+ "'run net_nfs' to get Kernel over TFTP and mount root " \
+ "filesystem over NFS;echo\0" \
+ "project_dir=systemone\0" \
+ "root_path=setenv rootpath /home/projects/${project_dir}/rootfs\0" \
+ "rootfs=/dev/mtdblock5\0" \
+ "rootfs_fallback=/dev/mtdblock7\0" \
+ "setbootargs=setenv bootargs ${bootargs} console=ttyMTD,mtdoops " \
+ "root=${rootfs} rootfstype=jffs2 panic=7 " \
+ "at91sam9_wdt.wdt_timeout=16\0" \
+ "stderr=serial\0" \
+ "stdin=serial\0" \
+ "stdout=serial\0" \
+ "upgrade_available=0\0"
+#endif
+#endif /* #ifndef CONFIG_SPL_BUILD */
/*
* Size of malloc() pool
*/
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * This header provides constants for TI K3-AM65 pinctrl bindings.
- *
- * Copyright (C) 2018 Texas Instruments
- */
-#ifndef _DT_BINDINGS_PINCTRL_TI_K3_AM65_H
-#define _DT_BINDINGS_PINCTRL_TI_K3_AM65_H
-
-/* K3 mux mode options for each pin. See TRM for options */
-#define MUX_MODE0 0
-#define MUX_MODE1 1
-#define MUX_MODE2 2
-#define MUX_MODE3 3
-#define MUX_MODE4 4
-#define MUX_MODE5 5
-#define MUX_MODE6 6
-#define MUX_MODE7 7
-#define MUX_MODE15 15
-
-#define PULL_DISABLE (1 << 16)
-#define PULL_UP (1 << 17)
-#define INPUT_EN (1 << 18)
-#define SLEWCTRL_200MHZ 0
-#define SLEWCTRL_150MHZ (1 << 19)
-#define SLEWCTRL_100MHZ (2 << 19)
-#define SLEWCTRL_50MHZ (3 << 19)
-#define TX_DIS (1 << 21)
-#define ISO_OVR (1 << 22)
-#define ISO_BYPASS (1 << 23)
-#define DS_EN (1 << 24)
-#define DS_INPUT (1 << 25)
-#define DS_FORCE_OUT_HIGH (1 << 26)
-#define DS_PULL_UP_DOWN_EN 0
-#define DS_PULL_UP_DOWN_DIS (1 << 27)
-#define DS_PULL_UP_SEL (1 << 28)
-#define WAKEUP_ENABLE (1 << 29)
-
-#define PIN_OUTPUT (PULL_DISABLE)
-#define PIN_OUTPUT_PULLUP (PULL_UP)
-#define PIN_OUTPUT_PULLDOWN 0
-#define PIN_INPUT (INPUT_EN | PULL_DISABLE)
-#define PIN_INPUT_PULLUP (INPUT_EN | PULL_UP)
-#define PIN_INPUT_PULLDOWN (INPUT_EN)
-
-#define AM65X_IOPAD(pa, val) (((pa) & 0x1fff)) (val)
-#define AM65X_WKUP_IOPAD(pa, val) (((pa) & 0x1fff)) (val)
-
-#endif
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * This header provides constants for TI K3-AM65 pinctrl bindings.
+ *
+ * Copyright (C) 2018 Texas Instruments
+ */
+#ifndef _DT_BINDINGS_PINCTRL_TI_K3_AM65_H
+#define _DT_BINDINGS_PINCTRL_TI_K3_AM65_H
+
+#define PULL_DISABLE (1 << 16)
+#define PULL_UP (1 << 17)
+#define INPUT_EN (1 << 18)
+#define SLEWCTRL_200MHZ 0
+#define SLEWCTRL_150MHZ (1 << 19)
+#define SLEWCTRL_100MHZ (2 << 19)
+#define SLEWCTRL_50MHZ (3 << 19)
+#define TX_DIS (1 << 21)
+#define ISO_OVR (1 << 22)
+#define ISO_BYPASS (1 << 23)
+#define DS_EN (1 << 24)
+#define DS_INPUT (1 << 25)
+#define DS_FORCE_OUT_HIGH (1 << 26)
+#define DS_PULL_UP_DOWN_EN 0
+#define DS_PULL_UP_DOWN_DIS (1 << 27)
+#define DS_PULL_UP_SEL (1 << 28)
+#define WAKEUP_ENABLE (1 << 29)
+
+#define PIN_OUTPUT (PULL_DISABLE)
+#define PIN_OUTPUT_PULLUP (PULL_UP)
+#define PIN_OUTPUT_PULLDOWN 0
+#define PIN_INPUT (INPUT_EN | PULL_DISABLE)
+#define PIN_INPUT_PULLUP (INPUT_EN | PULL_UP)
+#define PIN_INPUT_PULLDOWN (INPUT_EN)
+
+#define AM65X_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode))
+#define AM65X_WKUP_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode))
+
+#endif
*/
int fs_size(const char *filename, loff_t *size);
-/*
- * fs_read - Read file from the partition previously set by fs_set_blk_dev()
- * Note that not all filesystem types support either/both offset!=0 or len!=0.
+/**
+ * fs_read() - read file from the partition previously set by fs_set_blk_dev()
+ *
+ * Note that not all filesystem drivers support either or both of offset != 0
+ * and len != 0.
*
- * @filename: Name of file to read from
- * @addr: The address to read into
- * @offset: The offset in file to read from
- * @len: The number of bytes to read. Maybe 0 to read entire file
- * @actread: Returns the actual number of bytes read
- * @return 0 if ok with valid *actread, -1 on error conditions
+ * @filename: full path of the file to read from
+ * @addr: address of the buffer to write to
+ * @offset: offset in the file from where to start reading
+ * @len: the number of bytes to read. Use 0 to read entire file.
+ * @actread: returns the actual number of bytes read
+ * Return: 0 if OK with valid *actread, -1 on error conditions
*/
int fs_read(const char *filename, ulong addr, loff_t offset, loff_t len,
loff_t *actread);
-/*
- * fs_write - Write file to the partition previously set by fs_set_blk_dev()
- * Note that not all filesystem types support offset!=0.
+/**
+ * fs_write() - write file to the partition previously set by fs_set_blk_dev()
+ *
+ * Note that not all filesystem drivers support offset != 0.
*
- * @filename: Name of file to read from
- * @addr: The address to read into
- * @offset: The offset in file to read from. Maybe 0 to write to start of file
- * @len: The number of bytes to write
- * @actwrite: Returns the actual number of bytes written
- * @return 0 if ok with valid *actwrite, -1 on error conditions
+ * @filename: full path of the file to write to
+ * @addr: address of the buffer to read from
+ * @offset: offset in the file from where to start writing
+ * @len: the number of bytes to write
+ * @actwrite: returns the actual number of bytes written
+ * Return: 0 if OK with valid *actwrite, -1 on error conditions
*/
int fs_write(const char *filename, ulong addr, loff_t offset, loff_t len,
loff_t *actwrite);
This enables support for LZO compression algorithm.r
config GZIP
- bool "Enable gzip decompression support for SPL build"
+ bool "Enable gzip decompression support"
select ZLIB
default y
help
#include <efi_loader.h>
#include <div64.h>
#include <hexdump.h>
-#include <uuid.h>
#include <stdarg.h>
#include <linux/ctype.h>
#include <linux/err.h>
CONFIG_BOARDDIR
CONFIG_BOARDNAME
CONFIG_BOARDNAME_LOCAL
-CONFIG_BOARD_AXM
CONFIG_BOARD_COMMON
CONFIG_BOARD_ECC_SUPPORT
CONFIG_BOARD_IS_OPENRD_BASE
CONFIG_BOARD_POSTCLK_INIT
CONFIG_BOARD_REVISION_TAG
CONFIG_BOARD_SIZE_LIMIT
-CONFIG_BOARD_TAURUS
CONFIG_BOOGER
CONFIG_BOOTBLOCK
CONFIG_BOOTFILE
ifneq ($(CROSS_BUILD_TOOLS),)
override HOSTCC = $(CC)
+override HOSTCFLAGS = $(CFLAGS)
quiet_cmd_crosstools_strip = STRIP $^
cmd_crosstools_strip = $(STRIP) $^; touch $@
projects / oweals / u-boot.git / commitdiff