imply CMD_UBI if NAND
imply DISTRO_DEFAULTS
imply FAT_WRITE
+ imply FIT
imply OF_LIBFDT_OVERLAY
imply PRE_CONSOLE_BUFFER
imply SPL_GPIO_SUPPORT
sun8i-a83t-cubietruck-plus.dtb \
sun8i-a83t-tbs-a711.dts
dtb-$(CONFIG_MACH_SUN8I_H3) += \
+ sun8i-h2-plus-bananapi-m2-zero.dtb \
sun8i-h2-plus-libretech-all-h3-cc.dtb \
sun8i-h2-plus-orangepi-r1.dtb \
sun8i-h2-plus-orangepi-zero.dtb \
sun50i-h5-orangepi-prime.dtb \
sun50i-h5-orangepi-zero-plus2.dtb
dtb-$(CONFIG_MACH_SUN50I_H6) += \
+ sun50i-h6-orangepi-lite2.dtb \
sun50i-h6-orangepi-one-plus.dtb \
sun50i-h6-pine-h64.dtb
dtb-$(CONFIG_MACH_SUN50I) += \
sun50i-a64-orangepi-win.dtb \
sun50i-a64-pine64-plus.dtb \
sun50i-a64-pine64.dtb \
+ sun50i-a64-pinebook.dtb \
sun50i-a64-sopine-baseboard.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
sun9i-a80-optimus.dtb \
stdout-path = "serial0:115200n8";
};
- reg_vcc3v3: vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "vcc3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rtc 1>;
+ clock-names = "ext_clock";
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* WL-PMU-EN: PL2 */
};
};
status = "okay";
};
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <®_dcdc1>;
+ /*
+ * Schematic shows both dldo4 and eldo1 connected for vcc-io-wifi, but
+ * dldo4 connection shows DNP(Do Not Populate) and eldo1 connected with
+ * 0Ohm register to vcc-io-wifi so eldo1 is used.
+ */
+ vqmmc-supply = <®_eldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* WL-WAKE-AP: PL3 */
+ interrupt-names = "host-wake";
+ };
+};
+
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
- vmmc-supply = <®_vcc3v3>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <8>;
non-removable;
cap-mmc-hw-reset;
status = "okay";
};
+&r_rsb {
+ status = "okay";
+
+ axp803: pmic@3a3 {
+ compatible = "x-powers,axp803";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */
+ };
+};
+
+#include "axp803.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "avdd-csi";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1040000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-hdmi-dsi-sensor";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-mipi";
+};
+
+®_dldo3 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "dovdd-csi";
+};
+
+®_dldo4 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-io";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+®_eldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "cpvdd";
+};
+
+®_eldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dvdd-csi";
+};
+
+®_fldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+®_fldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
&usbphy {
usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+ usb0_vbus-supply = <®_drivevbus>;
status = "okay";
};
stdout-path = "serial0:115200n8";
};
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
};
};
+&de {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
status = "okay";
};
+&hdmi {
+ hvcc-supply = <®_dldo1>;
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
&mmc2 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins>;
+ pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
vmmc-supply = <®_dcdc1>;
bus-width = <8>;
non-removable;
regulator-name = "vcc-rtc";
};
+&simplefb_hdmi {
+ vcc-hdmi-supply = <®_dldo1>;
+};
+
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
compatible = "friendlyarm,nanopi-a64", "allwinner,sun50i-a64";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ blue {
+ label = "nanopi-a64:blue:status";
+ gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rtc 1>;
+ clock-names = "ext_clock";
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+ };
+};
+
+&de {
+ status = "okay";
};
&ehci0 {
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ phy-supply = <®_dcdc1>;
+ status = "okay";
+};
+
+&hdmi {
+ hvcc-supply = <®_dldo1>;
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
/* i2c1 connected with gpio headers like pine64, bananapi */
&i2c1 {
pinctrl-names = "default";
bias-pull-up;
};
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <7>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
status = "okay";
};
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_dldo4>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ rtl8189etv: wifi@1 {
+ reg = <1>;
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
+ interrupt-names = "host-wake";
+ };
+};
+
&ohci0 {
status = "okay";
};
®_dcdc1 {
regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-3v";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
};
®_dcdc2 {
regulator-name = "vcc-rtc";
};
+&simplefb_hdmi {
+ vcc-hdmi-supply = <®_dldo1>;
+};
+
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
compatible = "olimex,a64-olinuxino", "allwinner,sun50i-a64";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
stdout-path = "serial0:115200n8";
};
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ reg_usb1_vbus: usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&pio 6 9 GPIO_ACTIVE_HIGH>; /* PG9 */
+ status = "okay";
+ };
+
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
};
};
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ phy-supply = <®_dcdc1>;
+ allwinner,tx-delay-ps = <600>;
+ status = "okay";
+};
+
+&hdmi {
+ hvcc-supply = <®_dldo1>;
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
};
};
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
&r_rsb {
status = "okay";
reg = <0x3a3>;
interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */
};
};
/* DCDC3 is polyphased with DCDC2 */
+/*
+ * The board uses DDR3L DRAM chips. 1.36V is the closest to the nominal
+ * 1.35V that the PMIC can drive.
+ */
®_dcdc5 {
regulator-always-on;
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1500000>;
+ regulator-min-microvolt = <1360000>;
+ regulator-max-microvolt = <1360000>;
regulator-name = "vcc-ddr3";
};
regulator-name = "vcc-wifi-io";
};
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
®_eldo1 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "vcc-rtc";
};
+&simplefb_hdmi {
+ vcc-hdmi-supply = <®_dldo1>;
+};
+
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
status = "okay";
+ usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+ usb0_vbus-supply = <®_drivevbus>;
+ usb1_vbus-supply = <®_usb1_vbus>;
};
/*
* Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
+ * Copyright (C) 2017-2018 Samuel Holland <samuel@sholland.org>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
compatible = "xunlong,orangepi-win", "allwinner,sun50i-a64";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &uart2;
+ serial3 = &uart3;
+ serial4 = &uart4;
};
chosen {
stdout-path = "serial0:115200n8";
};
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ status {
+ label = "orangepi:green:status";
+ gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
+ };
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&pio 3 14 GPIO_ACTIVE_HIGH>; /* PD14 */
+ status = "okay";
+ };
+
+ reg_usb1_vbus: usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&pio 3 7 GPIO_ACTIVE_HIGH>; /* PD7 */
+ status = "okay";
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 8 GPIO_ACTIVE_LOW>; /* PL8 */
+ };
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
};
&ehci1 {
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ phy-supply = <®_gmac_3v3>;
+ status = "okay";
+};
+
+&hdmi {
+ hvcc-supply = <®_dldo1>;
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
vmmc-supply = <®_dcdc1>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ disable-wp;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <®_dldo2>;
+ vqmmc-supply = <®_dldo4>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&ohci0 {
status = "okay";
};
#include "axp803.dtsi"
®_aldo1 {
- regulator-always-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
regulator-name = "afvcc-csi";
};
regulator-name = "vcc-wifi-io";
};
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
®_eldo1 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "cpvdd";
};
+®_eldo3 {
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dvdd-csi";
+};
+
®_fldo1 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-name = "vcc-rtc";
};
+&simplefb_hdmi {
+ vcc-hdmi-supply = <®_dldo1>;
+};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash@0 {
+ compatible = "mxicy,mx25l1606e", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <80000000>;
+ m25p,fast-read;
+ status = "okay";
+ };
+};
+
+/* On debug connector */
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
-&usbphy {
+/* Bluetooth */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ status = "okay";
+};
+
+/* On Pi-2 connector, RTS/CTS optional */
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+/* On Pi-2 connector, RTS/CTS optional */
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "disabled";
+};
+
+/* On Pi-2 connector (labeled for SPI1), RTS/CTS optional */
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins>;
+ status = "disabled";
+};
+
+&usb_otg {
+ dr_mode = "otg";
status = "okay";
};
+&usbphy {
+ usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+ usb0_vbus-supply = <®_drivevbus>;
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
--- /dev/null
+/*
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ *
+ * Copyright (c) 2018 ARM Ltd.
+ */
+
+#include "sun50i-a64-sopine-baseboard.dts"
+
+/ {
+ model = "Pine64 LTS";
+ compatible = "pine64,pine64-lts", "allwinner,sun50i-r18",
+ "allwinner,sun50i-a64";
+};
chosen {
stdout-path = "serial0:115200n8";
};
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+};
+
+&de {
+ status = "okay";
};
&ehci0 {
};
+&hdmi {
+ hvcc-supply = <®_dldo1>;
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
regulator-name = "vcc-rtc";
};
+&simplefb_hdmi {
+ vcc-hdmi-supply = <®_dldo1>;
+};
+
/* On Euler connector */
&spdif {
status = "disabled";
/* On Exp and Euler connectors */
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 Vasily Khoruzhick <anarsoul@gmail.com>
+ *
+ */
+
+/* The ANX6345 eDP-bridge is on r_i2c */
+&r_i2c {
+ anx6345: edp-bridge@38 {
+ compatible = "analogix,anx6345";
+ reg = <0x38>;
+ reset-gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */
+ status = "okay";
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.xyz>
+ * Copyright (C) 2018 Vasily Khoruzhick <anarsoul@gmail.com>
+ *
+ */
+
+/dts-v1/;
+
+#include "sun50i-a64.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "Pinebook";
+ compatible = "pine64,pinebook", "allwinner,sun50i-a64";
+
+ aliases {
+ serial0 = &uart0;
+ ethernet0 = &rtl8723cs;
+ };
+
+ vdd_bl: regulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "bl-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+ enable-active-high;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 50000 0>;
+ brightness-levels = <0 5 10 15 20 30 40 55 70 85 100>;
+ default-brightness-level = <2>;
+ enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */
+ power-supply = <&vdd_bl>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+
+ framebuffer-lcd {
+ panel-supply = <®_dc1sw>;
+ dvdd25-supply = <®_dldo2>;
+ dvdd12-supply = <®_fldo1>;
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ lid_switch {
+ label = "Lid Switch";
+ gpios = <&r_pio 0 12 GPIO_ACTIVE_LOW>; /* PL12 */
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_LID>;
+ linux,can-disable;
+ wakeup-source;
+ };
+ };
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+ };
+};
+
+&ehci0 {
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ vmmc-supply = <®_dcdc1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <®_dldo4>;
+ vqmmc-supply = <®_eldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ rtl8723cs: wifi@1 {
+ reg = <1>;
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_eldo1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ mmc-hs200-1_8v;
+ status = "okay";
+};
+
+&ohci0 {
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&pwm {
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp803: pmic@3a3 {
+ compatible = "x-powers,axp803";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+/* The ANX6345 eDP-bridge is on r_i2c */
+&r_i2c {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_i2c_pl89_pins>;
+ status = "okay";
+};
+
+#include "axp803.dtsi"
+
+®_aldo1 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "vcc-csi";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dc1sw {
+ regulator-name = "vcc-lcd";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-hdmi";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vcc-edp";
+};
+
+®_dldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avdd-csi";
+};
+
+®_dldo4 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_eldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "cpvdd";
+};
+
+®_eldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vdd-1v8-csi";
+};
+
+®_fldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-1v2-hsic";
+};
+
+®_fldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_ldo_io0 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-usb";
+ status = "okay";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+&simplefb_hdmi {
+ vcc-hdmi-supply = <®_dldo1>;
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "host";
+};
+
+&usbphy {
+ usb0_vbus-supply = <®_ldo_io0>;
+ usb1_vbus-supply = <®_ldo_io0>;
+ status = "okay";
+};
stdout-path = "serial0:115200n8";
};
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
reg_vcc1v8: vcc1v8 {
compatible = "regulator-fixed";
regulator-name = "vcc1v8";
};
};
+&de {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
status = "okay";
};
+&hdmi {
+ hvcc-supply = <®_dldo1>;
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&mdio {
ext_rgmii_phy: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
regulator-name = "vcc-wifi";
};
+&simplefb_hdmi {
+ vcc-hdmi-supply = <®_dldo1>;
+};
+
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
#include "sun50i-a64.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
non-removable;
disable-wp;
bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
};
};
+&spi0 {
+ status = "okay";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ };
+};
+
#include "axp803.dtsi"
®_aldo2 {
*/
#include <dt-bindings/clock/sun50i-a64-ccu.h>
+#include <dt-bindings/clock/sun8i-de2.h>
#include <dt-bindings/clock/sun8i-r-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/reset/sun50i-a64-ccu.h>
+#include <dt-bindings/reset/sun8i-de2.h>
+#include <dt-bindings/reset/sun8i-r-ccu.h>
/ {
interrupt-parent = <&gic>;
#size-cells = <1>;
ranges;
-/*
- * The pipeline mixer0-lcd0 depends on clock CLK_MIXER0 from DE2 CCU.
- * However there is no support for this clock on A64 yet, so we depend
- * on the upstream clocks here to keep them (and thus CLK_MIXER0) up.
- */
simplefb_lcd: framebuffer-lcd {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "mixer0-lcd0";
clocks = <&ccu CLK_TCON0>,
- <&ccu CLK_DE>, <&ccu CLK_BUS_DE>;
+ <&display_clocks CLK_MIXER0>;
+ status = "disabled";
+ };
+
+ simplefb_hdmi: framebuffer-hdmi {
+ compatible = "allwinner,simple-framebuffer",
+ "simple-framebuffer";
+ allwinner,pipeline = "mixer1-lcd1-hdmi";
+ clocks = <&display_clocks CLK_MIXER1>,
+ <&ccu CLK_TCON1>, <&ccu CLK_HDMI>;
status = "disabled";
};
};
device_type = "cpu";
reg = <0>;
enable-method = "psci";
+ next-level-cache = <&L2>;
};
cpu1: cpu@1 {
device_type = "cpu";
reg = <1>;
enable-method = "psci";
+ next-level-cache = <&L2>;
};
cpu2: cpu@2 {
device_type = "cpu";
reg = <2>;
enable-method = "psci";
+ next-level-cache = <&L2>;
};
cpu3: cpu@3 {
device_type = "cpu";
reg = <3>;
enable-method = "psci";
+ next-level-cache = <&L2>;
};
+
+ L2: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ de: display-engine {
+ compatible = "allwinner,sun50i-a64-display-engine";
+ allwinner,pipelines = <&mixer0>,
+ <&mixer1>;
+ status = "disabled";
};
osc24M: osc24M_clk {
#size-cells = <1>;
ranges;
+ de2@1000000 {
+ compatible = "allwinner,sun50i-a64-de2";
+ reg = <0x1000000 0x400000>;
+ allwinner,sram = <&de2_sram 1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1000000 0x400000>;
+
+ display_clocks: clock@0 {
+ compatible = "allwinner,sun50i-a64-de2-clk";
+ reg = <0x0 0x100000>;
+ clocks = <&ccu CLK_DE>,
+ <&ccu CLK_BUS_DE>;
+ clock-names = "mod",
+ "bus";
+ resets = <&ccu RST_BUS_DE>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ mixer0: mixer@100000 {
+ compatible = "allwinner,sun50i-a64-de2-mixer-0";
+ reg = <0x100000 0x100000>;
+ clocks = <&display_clocks CLK_BUS_MIXER0>,
+ <&display_clocks CLK_MIXER0>;
+ clock-names = "bus",
+ "mod";
+ resets = <&display_clocks RST_MIXER0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mixer0_out: port@1 {
+ reg = <1>;
+
+ mixer0_out_tcon0: endpoint {
+ remote-endpoint = <&tcon0_in_mixer0>;
+ };
+ };
+ };
+ };
+
+ mixer1: mixer@200000 {
+ compatible = "allwinner,sun50i-a64-de2-mixer-1";
+ reg = <0x200000 0x100000>;
+ clocks = <&display_clocks CLK_BUS_MIXER1>,
+ <&display_clocks CLK_MIXER1>;
+ clock-names = "bus",
+ "mod";
+ resets = <&display_clocks RST_MIXER1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mixer1_out: port@1 {
+ reg = <1>;
+
+ mixer1_out_tcon1: endpoint {
+ remote-endpoint = <&tcon1_in_mixer1>;
+ };
+ };
+ };
+ };
+ };
+
syscon: syscon@1c00000 {
- compatible = "allwinner,sun50i-a64-system-controller",
+ compatible = "allwinner,sun50i-a64-system-control",
"syscon";
reg = <0x01c00000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ sram_c: sram@18000 {
+ compatible = "mmio-sram";
+ reg = <0x00018000 0x28000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x00018000 0x28000>;
+
+ de2_sram: sram-section@0 {
+ compatible = "allwinner,sun50i-a64-sram-c";
+ reg = <0x0000 0x28000>;
+ };
+ };
};
dma: dma-controller@1c02000 {
#dma-cells = <1>;
};
+ tcon0: lcd-controller@1c0c000 {
+ compatible = "allwinner,sun50i-a64-tcon-lcd",
+ "allwinner,sun8i-a83t-tcon-lcd";
+ reg = <0x01c0c000 0x1000>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>;
+ clock-names = "ahb", "tcon-ch0";
+ clock-output-names = "tcon-pixel-clock";
+ resets = <&ccu RST_BUS_TCON0>, <&ccu RST_BUS_LVDS>;
+ reset-names = "lcd", "lvds";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon0_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ tcon0_in_mixer0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&mixer0_out_tcon0>;
+ };
+ };
+
+ tcon0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
+ };
+
+ tcon1: lcd-controller@1c0d000 {
+ compatible = "allwinner,sun50i-a64-tcon-tv",
+ "allwinner,sun8i-a83t-tcon-tv";
+ reg = <0x01c0d000 0x1000>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TCON1>, <&ccu CLK_TCON1>;
+ clock-names = "ahb", "tcon-ch1";
+ resets = <&ccu RST_BUS_TCON1>;
+ reset-names = "lcd";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon1_in: port@0 {
+ reg = <0>;
+
+ tcon1_in_mixer1: endpoint {
+ remote-endpoint = <&mixer1_out_tcon1>;
+ };
+ };
+
+ tcon1_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ tcon1_out_hdmi: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&hdmi_in_tcon1>;
+ };
+ };
+ };
+ };
+
mmc0: mmc@1c0f000 {
compatible = "allwinner,sun50i-a64-mmc";
reg = <0x01c0f000 0x1000>;
#size-cells = <0>;
};
+ sid: eeprom@1c14000 {
+ compatible = "allwinner,sun50i-a64-sid";
+ reg = <0x1c14000 0x400>;
+ };
+
usb_otg: usb@1c19000 {
compatible = "allwinner,sun8i-a33-musb";
reg = <0x01c19000 0x0400>;
};
mmc2_pins: mmc2-pins {
- pins = "PC1", "PC5", "PC6", "PC8", "PC9",
+ pins = "PC5", "PC6", "PC8", "PC9",
"PC10","PC11", "PC12", "PC13",
"PC14", "PC15", "PC16";
function = "mmc2";
bias-pull-up;
};
+ mmc2_ds_pin: mmc2-ds-pin {
+ pins = "PC1";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ pwm_pin: pwm_pin {
+ pins = "PD22";
+ function = "pwm";
+ };
+
rmii_pins: rmii_pins {
pins = "PD10", "PD11", "PD13", "PD14", "PD17",
"PD18", "PD19", "PD20", "PD22", "PD23";
function = "spi1";
};
- uart0_pins_a: uart0 {
+ uart0_pb_pins: uart0-pb-pins {
pins = "PB8", "PB9";
function = "uart0";
};
status = "disabled";
};
- pwm: pwm@1c21400 {
- compatible = "allwinner,sun50i-a64-pwm",
- "allwinner,sun5i-a13-pwm";
- reg = <0x01c21400 0x8>;
- clocks = <&osc24M>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
uart0: serial@1c28000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28000 0x400>;
clocks = <&ccu CLK_BUS_EMAC>;
clock-names = "stmmaceth";
status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
mdio: mdio {
compatible = "snps,dwmac-mdio";
#interrupt-cells = <3>;
};
+ pwm: pwm@1c21400 {
+ compatible = "allwinner,sun50i-a64-pwm",
+ "allwinner,sun5i-a13-pwm";
+ reg = <0x01c21400 0x400>;
+ clocks = <&osc24M>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm_pin>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ hdmi: hdmi@1ee0000 {
+ compatible = "allwinner,sun50i-a64-dw-hdmi",
+ "allwinner,sun8i-a83t-dw-hdmi";
+ reg = <0x01ee0000 0x10000>;
+ reg-io-width = <1>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
+ <&ccu CLK_HDMI>;
+ clock-names = "iahb", "isfr", "tmds";
+ resets = <&ccu RST_BUS_HDMI1>;
+ reset-names = "ctrl";
+ phys = <&hdmi_phy>;
+ phy-names = "hdmi-phy";
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hdmi_in: port@0 {
+ reg = <0>;
+
+ hdmi_in_tcon1: endpoint {
+ remote-endpoint = <&tcon1_out_hdmi>;
+ };
+ };
+
+ hdmi_out: port@1 {
+ reg = <1>;
+ };
+ };
+ };
+
+ hdmi_phy: hdmi-phy@1ef0000 {
+ compatible = "allwinner,sun50i-a64-hdmi-phy";
+ reg = <0x01ef0000 0x10000>;
+ clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
+ <&ccu 7>;
+ clock-names = "bus", "mod", "pll-0";
+ resets = <&ccu RST_BUS_HDMI0>;
+ reset-names = "phy";
+ #phy-cells = <0>;
+ };
+
rtc: rtc@1f00000 {
compatible = "allwinner,sun6i-a31-rtc";
reg = <0x01f00000 0x54>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ clock-output-names = "rtc-osc32k", "rtc-osc32k-out";
+ clocks = <&osc32k>;
+ #clock-cells = <1>;
};
r_intc: interrupt-controller@1f00c00 {
#reset-cells = <1>;
};
+ r_i2c: i2c@1f02400 {
+ compatible = "allwinner,sun50i-a64-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x01f02400 0x400>;
+ interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_APB0_I2C>;
+ resets = <&r_ccu RST_APB0_I2C>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ r_pwm: pwm@1f03800 {
+ compatible = "allwinner,sun50i-a64-pwm",
+ "allwinner,sun5i-a13-pwm";
+ reg = <0x01f03800 0x400>;
+ clocks = <&osc24M>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_pwm_pin>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
r_pio: pinctrl@1f02c00 {
compatible = "allwinner,sun50i-a64-r-pinctrl";
reg = <0x01f02c00 0x400>;
interrupt-controller;
#interrupt-cells = <3>;
+ r_i2c_pl89_pins: r-i2c-pl89-pins {
+ pins = "PL8", "PL9";
+ function = "s_i2c";
+ };
+
+ r_pwm_pin: pwm {
+ pins = "PL10";
+ function = "s_pwm";
+ };
+
r_rsb_pins: rsb {
pins = "PL0", "PL1";
function = "s_rsb";
status = "okay";
};
+&spi0 {
+ status = "okay";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ };
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
};
};
-/*
&spi0 {
status = "okay";
spi-max-frequency = <40000000>;
};
};
-*/
&ohci0 {
status = "okay";
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2018 Jagan Teki <jagan@openedev.com>
+ */
+
+#include "sun50i-h6-orangepi.dtsi"
+
+/ {
+ model = "OrangePi Lite2";
+ compatible = "xunlong,orangepi-lite2", "allwinner,sun50i-h6";
+};
* Author: Jagan Teki <jagan@amarulasolutions.com>
*/
-/dts-v1/;
-
-#include "sun50i-h6.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
+#include "sun50i-h6-orangepi.dtsi"
/ {
model = "OrangePi One Plus";
compatible = "xunlong,orangepi-one-plus", "allwinner,sun50i-h6";
-
- aliases {
- serial0 = &uart0;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-};
-
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins>;
- vmmc-supply = <®_cldo1>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
- bus-width = <4>;
- status = "okay";
-};
-
-&r_i2c {
- status = "okay";
-
- axp805: pmic@36 {
- compatible = "x-powers,axp805", "x-powers,axp806";
- reg = <0x36>;
- interrupt-parent = <&r_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #interrupt-cells = <1>;
- x-powers,self-working-mode;
-
- regulators {
- reg_aldo1: aldo1 {
- regulator-always-on;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-pl";
- };
-
- reg_aldo2: aldo2 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-ac200";
- };
-
- reg_aldo3: aldo3 {
- regulator-always-on;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc25-dram";
- };
-
- reg_bldo1: bldo1 {
- regulator-always-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-name = "vcc-bias-pll";
- };
-
- reg_bldo2: bldo2 {
- regulator-always-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-name = "vcc-efuse-pcie-hdmi-io";
- };
-
- reg_bldo3: bldo3 {
- regulator-always-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-name = "vcc-dcxoio";
- };
-
- bldo4 {
- /* unused */
- };
-
- reg_cldo1: cldo1 {
- regulator-always-on;
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-3v3";
- };
-
- reg_cldo2: cldo2 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi-1";
- };
-
- reg_cldo3: cldo3 {
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi-2";
- };
-
- reg_dcdca: dcdca {
- regulator-always-on;
- regulator-min-microvolt = <810000>;
- regulator-max-microvolt = <1080000>;
- regulator-name = "vdd-cpu";
- };
-
- reg_dcdcc: dcdcc {
- regulator-min-microvolt = <810000>;
- regulator-max-microvolt = <1080000>;
- regulator-name = "vdd-gpu";
- };
-
- reg_dcdcd: dcdcd {
- regulator-always-on;
- regulator-min-microvolt = <960000>;
- regulator-max-microvolt = <960000>;
- regulator-name = "vdd-sys";
- };
-
- reg_dcdce: dcdce {
- regulator-always-on;
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-name = "vcc-dram";
- };
-
- sw {
- /* unused */
- };
- };
- };
-};
-
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_ph_pins>;
- status = "okay";
};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2018 Amarula Solutions
+ * Author: Jagan Teki <jagan@amarulasolutions.com>
+ */
+
+/dts-v1/;
+
+#include "sun50i-h6.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "OrangePi One Plus";
+ compatible = "xunlong,orangepi-one-plus", "allwinner,sun50i-h6";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ vmmc-supply = <®_cldo1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&r_i2c {
+ status = "okay";
+
+ axp805: pmic@36 {
+ compatible = "x-powers,axp805", "x-powers,axp806";
+ reg = <0x36>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ x-powers,self-working-mode;
+
+ regulators {
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+ };
+
+ reg_aldo2: aldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-ac200";
+ };
+
+ reg_aldo3: aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc25-dram";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-bias-pll";
+ };
+
+ reg_bldo2: bldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-efuse-pcie-hdmi-io";
+ };
+
+ reg_bldo3: bldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-dcxoio";
+ };
+
+ bldo4 {
+ /* unused */
+ };
+
+ reg_cldo1: cldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+ };
+
+ reg_cldo2: cldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-1";
+ };
+
+ reg_cldo3: cldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-2";
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdcc: dcdcc {
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-gpu";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <960000>;
+ regulator-max-microvolt = <960000>;
+ regulator-name = "vdd-sys";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dram";
+ };
+
+ sw {
+ /* unused */
+ };
+ };
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
+ * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Banana Pi BPI-M2-Zero";
+ compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+
+ pwr_led {
+ label = "bananapi-m2-zero:red:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
+ default-state = "on";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+
+ sw4 {
+ label = "power";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&mmc0 {
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ /*
+ * On the production batch of this board the card detect GPIO is
+ * high active (card inserted), although on the early samples it's
+ * low active.
+ */
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ /*
+ * There're two micro-USB connectors, one is power-only and another is
+ * OTG. The Vbus of these two connectors are connected together, so
+ * the external USB device will be powered just by the power input
+ * from the power-only USB port.
+ */
+ status = "okay";
+};
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <1>;
+ clocks = <&ccu CLK_CPUX>;
+ clock-names = "cpu";
operating-points-v2 = <&cpu0_opp_table>;
+ #cooling-cells = <2>;
};
cpu@2 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <2>;
+ clocks = <&ccu CLK_CPUX>;
+ clock-names = "cpu";
operating-points-v2 = <&cpu0_opp_table>;
+ #cooling-cells = <2>;
};
cpu@3 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <3>;
+ clocks = <&ccu CLK_CPUX>;
+ clock-names = "cpu";
operating-points-v2 = <&cpu0_opp_table>;
+ #cooling-cells = <2>;
};
};
};
soc {
+ system-control@1c00000 {
+ compatible = "allwinner,sun8i-h3-system-control";
+ reg = <0x01c00000 0x30>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ sram_c: sram@1d00000 {
+ compatible = "mmio-sram";
+ reg = <0x01d00000 0x80000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x01d00000 0x80000>;
+
+ ve_sram: sram-section@0 {
+ compatible = "allwinner,sun8i-h3-sram-c1",
+ "allwinner,sun4i-a10-sram-c1";
+ reg = <0x000000 0x80000>;
+ };
+ };
+ };
+
mali: gpu@1c40000 {
compatible = "allwinner,sun8i-h3-mali", "arm,mali-400";
reg = <0x01c40000 0x10000>;
reset-names = "stmmaceth";
clocks = <&ccu CLK_BUS_EMAC>;
clock-names = "stmmaceth";
- #address-cells = <1>;
- #size-cells = <0>;
status = "disabled";
mdio: mdio {
#define SUN8I_H3_GPL_R_TWI 2
#define SUN8I_A23_GPL_R_TWI 3
#define SUN8I_GPL_R_UART 2
+#define SUN50I_GPL_R_TWI 2
#define SUN9I_GPN_R_RSB 3
u32 cbda; /* 0x94 */
u32 res2[26];
#if defined(CONFIG_SUNXI_GEN_SUN6I) || defined(CONFIG_MACH_SUN50I_H6)
- u32 res3[64];
+ u32 res3[17];
+ u32 samp_dl;
+ u32 res4[46];
#endif
u32 fifo; /* 0x100 / 0x200 FIFO access address */
};
#define SUNXI_MMC_COMMON_CLK_GATE (1 << 16)
#define SUNXI_MMC_COMMON_RESET (1 << 18)
+#define SUNXI_MMC_CAL_DL_SW_EN (0x1 << 7)
+
struct mmc *sunxi_mmc_init(int sdc_no);
#endif /* _SUNXI_MMC_H */
select ARM64
select DM_I2C
select PHY_SUN4I_USB
+ select SUN6I_PRCM
select SUNXI_DE2
select SUNXI_GEN_SUN6I
select SUPPORT_SPL
{
struct sunxi_ccm_reg * const ccm =
(struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
+#ifdef CONFIG_SUNXI_DE2
+ const int m = 4; /* 6 MHz steps to allow higher frequency for DE2 */
+#else
const int m = 8; /* 3 MHz steps just like sun4i, sun5i and sun7i */
+#endif
if (clk == 0) {
clrbits_le32(&ccm->pll3_cfg, CCM_PLL3_CTRL_EN);
F: configs/Bananapi_m2m_defconfig
F: arch/arm/dts/sun8i-r16-bananapi-m2m.dts
+BANANAPI M2 ZERO BOARD
+M: Icenowy Zheng <icenowy@aosc.io>
+S: Maintained
+F: configs/bananapi_m2_zero_defconfig
+
BANANAPI M64
M: Jagan Teki <jagan@amarulasolutions.com>
S: Maintained
F: configs/A20-Olimex-SOM204-EVB_defconfig
F: configs/A20-Olimex-SOM204-EVB-eMMC_defconfig
+ORANGEPI LITE2 BOARD
+M: Jagan Teki <jagan@openedev.com>
+S: Maintained
+F: configs/orangepi_lite2_defconfig
+
ORANGEPI ONE PLUS BOARD
M: Jagan Teki <jagan@amarulasolutions.com>
S: Maintained
#endif
#ifdef CONFIG_R_I2C_ENABLE
+#ifdef CONFIG_MACH_SUN50I
+ clock_twi_onoff(5, 1);
+ sunxi_gpio_set_cfgpin(SUNXI_GPL(8), SUN50I_GPL_R_TWI);
+ sunxi_gpio_set_cfgpin(SUNXI_GPL(9), SUN50I_GPL_R_TWI);
+#else
clock_twi_onoff(5, 1);
sunxi_gpio_set_cfgpin(SUNXI_GPL(0), SUN8I_H3_GPL_R_TWI);
sunxi_gpio_set_cfgpin(SUNXI_GPL(1), SUN8I_H3_GPL_R_TWI);
#endif
+#endif
}
#if defined(CONFIG_ENV_IS_IN_MMC) && defined(CONFIG_ENV_IS_IN_FAT)
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN8I_H3=y
+CONFIG_DRAM_CLK=408
+CONFIG_DRAM_ZQ=3881979
+CONFIG_DRAM_ODT_EN=y
+CONFIG_MMC0_CD_PIN=""
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-h2-plus-bananapi-m2-zero"
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN50I_H6=y
+CONFIG_MMC0_CD_PIN="PF6"
+# CONFIG_PSCI_RESET is not set
+CONFIG_NR_DRAM_BANKS=1
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-orangepi-lite2"
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN50I=y
+CONFIG_SUNXI_DRAM_LPDDR3_STOCK=y
+CONFIG_DRAM_CLK=552
+CONFIG_DRAM_ZQ=3881949
+CONFIG_MMC0_CD_PIN=""
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+CONFIG_SPL_SPI_SUNXI=y
+CONFIG_NR_DRAM_BANKS=1
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-pine64-lts"
+CONFIG_SUN8I_EMAC=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
--- /dev/null
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_SPL=y
+CONFIG_MACH_SUN50I=y
+CONFIG_SUNXI_DRAM_LPDDR3_STOCK=y
+CONFIG_DRAM_CLK=552
+CONFIG_DRAM_ZQ=3881949
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+CONFIG_R_I2C_ENABLE=y
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-pinebook"
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_PWM=y
+CONFIG_PWM_SUNXI=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
+# CONFIG_USB_GADGET is not set
+CONFIG_VIDEO_BRIDGE=y
+CONFIG_VIDEO_BRIDGE_ANALOGIX_ANX6345=y
{
unsigned int pll, pll_hz, div, n, oclk_dly, sclk_dly;
bool new_mode = false;
+ bool calibrate = false;
u32 val = 0;
if (IS_ENABLED(CONFIG_MMC_SUNXI_HAS_NEW_MODE) && (priv->mmc_no == 2))
new_mode = true;
+#if defined(CONFIG_MACH_SUN50I) || defined(CONFIG_MACH_SUN50I_H6)
+ calibrate = true;
+#endif
+
/*
* The MMC clock has an extra /2 post-divider when operating in the new
* mode.
val = CCM_MMC_CTRL_MODE_SEL_NEW;
setbits_le32(&priv->reg->ntsr, SUNXI_MMC_NTSR_MODE_SEL_NEW);
#endif
- } else {
+ } else if (!calibrate) {
+ /*
+ * Use hardcoded delay values if controller doesn't support
+ * calibration
+ */
val = CCM_MMC_CTRL_OCLK_DLY(oclk_dly) |
CCM_MMC_CTRL_SCLK_DLY(sclk_dly);
}
rval &= ~SUNXI_MMC_CLK_DIVIDER_MASK;
writel(rval, &priv->reg->clkcr);
+#if defined(CONFIG_MACH_SUN50I) || defined(CONFIG_MACH_SUN50I_H6)
+ /* A64 supports calibration of delays on MMC controller and we
+ * have to set delay of zero before starting calibration.
+ * Allwinner BSP driver sets a delay only in the case of
+ * using HS400 which is not supported by mainline U-Boot or
+ * Linux at the moment
+ */
+ writel(SUNXI_MMC_CAL_DL_SW_EN, &priv->reg->samp_dl);
+#endif
+
/* Re-enable Clock */
rval |= SUNXI_MMC_CLK_ENABLE;
writel(rval, &priv->reg->clkcr);
int video_bridge_set_active(struct udevice *dev, bool active)
{
struct video_bridge_priv *uc_priv = dev_get_uclass_priv(dev);
- int ret;
+ int ret = 0;
debug("%s: %d\n", __func__, active);
- ret = dm_gpio_set_value(&uc_priv->sleep, !active);
- if (ret)
- return ret;
- if (active) {
+ if (uc_priv->sleep.dev) {
+ ret = dm_gpio_set_value(&uc_priv->sleep, !active);
+ if (ret)
+ return ret;
+ }
+
+ if (!active)
+ return 0;
+
+ if (uc_priv->reset.dev) {
ret = dm_gpio_set_value(&uc_priv->reset, true);
if (ret)
return ret;
void lcdc_pll_set(struct sunxi_ccm_reg *ccm, int tcon, int dotclock,
int *clk_div, int *clk_double, bool is_composite)
{
- int value, n, m, min_m, max_m, diff;
+ int value, n, m, min_m, max_m, diff, step;
int best_n = 0, best_m = 0, best_diff = 0x0FFFFFFF;
int best_double = 0;
bool use_mipi_pll = false;
+#ifdef CONFIG_SUNXI_DE2
+ step = 6000;
+#else
+ step = 3000;
+#endif
+
if (tcon == 0) {
#if defined(CONFIG_VIDEO_LCD_IF_PARALLEL) || defined(CONFIG_SUNXI_DE2)
min_m = 6;
*/
for (m = min_m; m <= max_m; m++) {
#ifndef CONFIG_SUNXI_DE2
- n = (m * dotclock) / 3000;
+ n = (m * dotclock) / step;
if ((n >= 9) && (n <= 127)) {
- value = (3000 * n) / m;
+ value = (step * n) / m;
diff = dotclock - value;
if (diff < best_diff) {
best_diff = diff;
#endif
/* No double clock on DE2 */
- n = (m * dotclock) / 6000;
+ n = (m * dotclock) / (step * 2);
if ((n >= 9) && (n <= 127)) {
- value = (6000 * n) / m;
+ value = (step * 2 * n) / m;
diff = dotclock - value;
if (diff < best_diff) {
best_diff = diff;
} else
#endif
{
- clock_set_pll3(best_n * 3000000);
- debug("dotclock: %dkHz = %dkHz: (%d * 3MHz * %d) / %d\n",
+ clock_set_pll3(best_n * step * 1000);
+ debug("dotclock: %dkHz = %dkHz: (%d * %dkHz * %d) / %d\n",
dotclock,
(best_double + 1) * clock_get_pll3() / best_m / 1000,
- best_double + 1, best_n, best_m);
+ best_double + 1, step, best_n, best_m);
}
if (tcon == 0) {
projects / oweals / u-boot.git / commitdiff