Tegra114: MMC: Add SD bus power-rail init routine
authorTom Warren <twarren@nvidia.com>
Mon, 18 Mar 2013 21:51:20 +0000 (14:51 -0700)
committerTom Warren <twarren@nvidia.com>
Mon, 25 Mar 2013 16:56:07 +0000 (09:56 -0700)
T114 requires SD bus power-rail bringup for the SDIO card on SDMMC3.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
board/nvidia/dalmore/dalmore.c

index 7449b5b99d560d770769f803aebb39bf1e9553ea..2c23a29db78a079f2faba21785f0188654d00dbd 100644 (file)
 #include <asm/arch/pinmux.h>
 #include <asm/arch/gp_padctrl.h>
 #include "pinmux-config-dalmore.h"
+#include <i2c.h>
+
+#define BAT_I2C_ADDRESS                0x48    /* TPS65090 charger */
+#define PMU_I2C_ADDRESS                0x58    /* TPS65913 PMU */
 
 /*
  * Routine: pinmux_init
@@ -37,3 +41,61 @@ void pinmux_init(void)
        /* Initialize any non-default pad configs (APB_MISC_GP regs) */
        padgrp_config_table(dalmore_padctrl, ARRAY_SIZE(dalmore_padctrl));
 }
+
+#if defined(CONFIG_TEGRA_MMC)
+/*
+ * Do I2C/PMU writes to bring up SD card bus power
+ *
+ */
+void board_sdmmc_voltage_init(void)
+{
+       uchar reg, data_buffer[1];
+       int ret;
+
+       ret = i2c_set_bus_num(0);/* PMU is on bus 0 */
+       if (ret)
+               printf("%s: i2c_set_bus_num returned %d\n", __func__, ret);
+
+       /* TPS65913: LDO9_VOLTAGE = 3.3V */
+       data_buffer[0] = 0x31;
+       reg = 0x61;
+
+       ret = i2c_write(PMU_I2C_ADDRESS, reg, 1, data_buffer, 1);
+       if (ret)
+               printf("%s: PMU i2c_write %02X<-%02X returned %d\n",
+                       __func__, reg, data_buffer[0], ret);
+
+       /* TPS65913: LDO9_CTRL = Active */
+       data_buffer[0] = 0x01;
+       reg = 0x60;
+
+       ret = i2c_write(PMU_I2C_ADDRESS, reg, 1, data_buffer, 1);
+       if (ret)
+               printf("%s: PMU i2c_write %02X<-%02X returned %d\n",
+                       __func__, reg, data_buffer[0], ret);
+
+       /* TPS65090: FET6_CTRL = enable output auto discharge, enable FET6 */
+       data_buffer[0] = 0x03;
+       reg = 0x14;
+
+       ret = i2c_write(BAT_I2C_ADDRESS, reg, 1, data_buffer, 1);
+       if (ret)
+               printf("%s: BAT i2c_write %02X<-%02X returned %d\n",
+                       __func__, reg, data_buffer[0], ret);
+}
+
+/*
+ * Routine: pin_mux_mmc
+ * Description: setup the MMC muxes, power rails, etc.
+ */
+void pin_mux_mmc(void)
+{
+       /*
+        * NOTE: We don't do mmc-specific pin muxes here.
+        * They were done globally in pinmux_init().
+        */
+
+       /* Bring up the SDIO3 power rail */
+       board_sdmmc_voltage_init();
+}
+#endif /* MMC */