at91-vinco.dtb
dtb-$(CONFIG_ARCH_BCM283X) += \
- bcm2835-rpi-a-plus.dtb \
bcm2835-rpi-a.dtb \
+ bcm2835-rpi-a-plus.dtb \
+ bcm2835-rpi-b.dtb \
bcm2835-rpi-b-plus.dtb \
bcm2835-rpi-b-rev2.dtb \
- bcm2835-rpi-b.dtb \
- bcm2835-rpi-zero-w.dtb \
+ bcm2835-rpi-cm1-io1.dtb \
+ bcm2835-rpi-zero.dtb \
+ bcm2835-rpi-zero-w.dtb\
bcm2836-rpi-2-b.dtb \
- bcm2837-rpi-3-b.dtb
+ bcm2837-rpi-3-a-plus.dtb \
+ bcm2837-rpi-3-b.dtb \
+ bcm2837-rpi-3-b-plus.dtb \
+ bcm2837-rpi-cm3-io3.dtb
dtb-$(CONFIG_ARCH_BCM63158) += \
bcm963158.dtb
+// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
leds {
act {
- gpios = <&gpio 47 0>;
+ gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
};
pwr {
label = "PWR";
- gpios = <&gpio 35 0>;
+ gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
default-state = "keep";
linux,default-trigger = "default-on";
};
* "FOO" = GPIO line named "FOO" on the schematic
* "FOO_N" = GPIO line named "FOO" on schematic, active low
*/
- gpio-line-names = "SDA0",
- "SCL0",
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
"SDA1",
"SCL1",
"GPIO_GCLK",
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
+// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
leds {
act {
- gpios = <&gpio 16 1>;
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
};
};
hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
+// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
leds {
act {
- gpios = <&gpio 47 0>;
+ gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
};
pwr {
label = "PWR";
- gpios = <&gpio 35 0>;
+ gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
default-state = "keep";
linux,default-trigger = "default-on";
};
* "FOO" = GPIO line named "FOO" on the schematic
* "FOO_N" = GPIO line named "FOO" on schematic, active low
*/
- gpio-line-names = "SDA0",
- "SCL0",
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
"SDA1",
"SCL1",
"GPIO_GCLK",
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
+// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
leds {
act {
- gpios = <&gpio 16 1>;
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
};
};
};
&hdmi {
- hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+ status = "okay";
};
&uart0 {
+// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
leds {
act {
- gpios = <&gpio 16 1>;
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
};
};
};
hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835-rpi-cm1.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+ compatible = "raspberrypi,compute-module", "brcm,bcm2835";
+ model = "Raspberry Pi Compute Module IO board rev1";
+};
+
+&gpio {
+ /*
+ * This is based on the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "GPIO0",
+ "GPIO1",
+ "GPIO2",
+ "GPIO3",
+ "GPIO4",
+ "GPIO5",
+ "GPIO6",
+ "GPIO7",
+ "GPIO8",
+ "GPIO9",
+ "GPIO10",
+ "GPIO11",
+ "GPIO12",
+ "GPIO13",
+ "GPIO14",
+ "GPIO15",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "GPIO28",
+ "GPIO29",
+ "GPIO30",
+ "GPIO31",
+ "GPIO32",
+ "GPIO33",
+ "GPIO34",
+ "GPIO35",
+ "GPIO36",
+ "GPIO37",
+ "GPIO38",
+ "GPIO39",
+ "GPIO40",
+ "GPIO41",
+ "GPIO42",
+ "GPIO43",
+ "GPIO44",
+ "GPIO45",
+ "HDMI_HPD_N",
+ /* Also used as ACT LED */
+ "EMMC_EN_N",
+ /* Used by eMMC */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
+ pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio14>;
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+
+/ {
+ leds {
+ act {
+ gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ reg_3v3: fixed-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_1v8: fixed-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+};
+
+&sdhost {
+ non-removable;
+ vmmc-supply = <®_3v3>;
+ vqmmc-supply = <®_1v8>;
+};
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2017 Stefan Wahren <stefan.wahren@i2se.com>
+ */
+
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
-#include "bcm283x-rpi-smsc9512.dtsi"
-#include "bcm283x-rpi-usb-host.dtsi"
+#include "bcm283x-rpi-usb-otg.dtsi"
/ {
compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
model = "Raspberry Pi Zero W";
+ chosen {
+ /* 8250 auxiliary UART instead of pl011 */
+ stdout-path = "serial1:115200n8";
+ };
+
leds {
act {
- gpios = <&gpio 47 0>;
+ gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
};
};
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
+ };
};
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_gpio14>;
- status = "okay";
+&gpio {
+ /*
+ * This is based on the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "GPIO5",
+ "GPIO6",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "GPIO12",
+ "GPIO13",
+ /* Serial port */
+ "TXD0",
+ "RXD0",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "SDA0",
+ "SCL0",
+ "NC", /* GPIO30 */
+ "NC", /* GPIO31 */
+ "NC", /* GPIO32 */
+ "NC", /* GPIO33 */
+ "NC", /* GPIO34 */
+ "NC", /* GPIO35 */
+ "NC", /* GPIO36 */
+ "NC", /* GPIO37 */
+ "NC", /* GPIO38 */
+ "NC", /* GPIO39 */
+ "CAM_GPIO1", /* GPIO40 */
+ "WL_ON", /* GPIO41 */
+ "NC", /* GPIO42 */
+ "WIFI_CLK", /* GPIO43 */
+ "CAM_GPIO0", /* GPIO44 */
+ "BT_ON", /* GPIO45 */
+ "HDMI_HPD_N",
+ "STATUS_LED_N",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
+ pinctrl-0 = <&gpioout &alt0>;
};
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
+
+&sdhci {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ non-removable;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio32 &uart0_ctsrts_gpio30>;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <2000000>;
+ shutdown-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_gpio14>;
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 Stefan Wahren <stefan.wahren@i2se.com>
+ */
+
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-usb-otg.dtsi"
+
+/ {
+ compatible = "raspberrypi,model-zero", "brcm,bcm2835";
+ model = "Raspberry Pi Zero";
+
+ leds {
+ act {
+ gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&gpio {
+ /*
+ * This is based on the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "GPIO5",
+ "GPIO6",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "GPIO12",
+ "GPIO13",
+ /* Serial port */
+ "TXD0",
+ "RXD0",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "SDA0",
+ "SCL0",
+ "NC", /* GPIO30 */
+ "NC", /* GPIO31 */
+ "CAM_GPIO1", /* GPIO32 */
+ "NC", /* GPIO33 */
+ "NC", /* GPIO34 */
+ "NC", /* GPIO35 */
+ "NC", /* GPIO36 */
+ "NC", /* GPIO37 */
+ "NC", /* GPIO38 */
+ "NC", /* GPIO39 */
+ "NC", /* GPIO40 */
+ "CAM_GPIO0", /* GPIO41 */
+ "NC", /* GPIO42 */
+ "NC", /* GPIO43 */
+ "NC", /* GPIO44 */
+ "NC", /* GPIO45 */
+ "HDMI_HPD_N",
+ "STATUS_LED_N",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
+ pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
+
+ /* I2S interface */
+ i2s_alt0: i2s_alt0 {
+ brcm,pins = <18 19 20 21>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+};
+
+&hdmi {
+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio14>;
+ status = "okay";
+};
#include <dt-bindings/power/raspberrypi-power.h>
/ {
- memory {
+ memory@0 {
device_type = "memory";
reg = <0 0x10000000>;
};
soc {
firmware: firmware {
- compatible = "raspberrypi,bcm2835-firmware";
+ compatible = "raspberrypi,bcm2835-firmware", "simple-bus";
mboxes = <&mailbox>;
};
firmware = <&firmware>;
#power-domain-cells = <1>;
};
+
+ vchiq: mailbox@7e00b840 {
+ compatible = "brcm,bcm2835-vchiq";
+ reg = <0x7e00b840 0x3c>;
+ interrupts = <0 2>;
+ };
};
};
&sdhci {
pinctrl-names = "default";
pinctrl-0 = <&emmc_gpio48>;
- status = "okay";
bus-width = <4>;
};
&sdhost {
pinctrl-names = "default";
pinctrl-0 = <&sdhost_gpio48>;
- bus-width = <4>;
-};
-
-&pwm {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
status = "okay";
+ bus-width = <4>;
};
&usb {
power-domains = <&power RPI_POWER_DOMAIN_USB>;
};
-&v3d {
- power-domains = <&power RPI_POWER_DOMAIN_V3D>;
-};
-
&hdmi {
power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
status = "okay";
+// SPDX-License-Identifier: GPL-2.0
#include "bcm283x.dtsi"
/ {
soc {
ranges = <0x7e000000 0x20000000 0x02000000>;
dma-ranges = <0x40000000 0x00000000 0x20000000>;
+ };
- arm-pmu {
- compatible = "arm,arm1176-pmu";
- };
+ arm-pmu {
+ compatible = "arm,arm1176-pmu";
};
};
+// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2836.dtsi"
-#include "bcm2835-rpi.dtsi"
+#include "bcm2836-rpi.dtsi"
#include "bcm283x-rpi-smsc9514.dtsi"
#include "bcm283x-rpi-usb-host.dtsi"
compatible = "raspberrypi,2-model-b", "brcm,bcm2836";
model = "Raspberry Pi 2 Model B";
- memory {
+ memory@0 {
reg = <0 0x40000000>;
};
leds {
act {
- gpios = <&gpio 47 0>;
+ gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
};
pwr {
label = "PWR";
- gpios = <&gpio 35 0>;
+ gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
default-state = "keep";
linux,default-trigger = "default-on";
};
};
&gpio {
+ /*
+ * Taken from rpi_SCH_2b_1p2_reduced.pdf and
+ * the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "GPIO5",
+ "GPIO6",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "GPIO12",
+ "GPIO13",
+ /* Serial port */
+ "TXD0",
+ "RXD0",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "SDA0",
+ "SCL0",
+ "", /* GPIO30 */
+ "LAN_RUN",
+ "CAM_GPIO1",
+ "", /* GPIO33 */
+ "", /* GPIO34 */
+ "PWR_LOW_N",
+ "", /* GPIO36 */
+ "", /* GPIO37 */
+ "USB_LIMIT",
+ "", /* GPIO39 */
+ "PWM0_OUT",
+ "CAM_GPIO0",
+ "SMPS_SCL",
+ "SMPS_SDA",
+ "ETHCLK",
+ "PWM1_OUT",
+ "HDMI_HPD_N",
+ "STATUS_LED",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
/* I2S interface */
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
+ status = "okay";
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+#include "bcm2835-rpi.dtsi"
+
+&vchiq {
+ compatible = "brcm,bcm2836-vchiq", "brcm,bcm2835-vchiq";
+};
+// SPDX-License-Identifier: GPL-2.0
#include "bcm283x.dtsi"
/ {
<0x40000000 0x40000000 0x00001000>;
dma-ranges = <0xc0000000 0x00000000 0x3f000000>;
- local_intc: local_intc {
+ local_intc: local_intc@40000000 {
compatible = "brcm,bcm2836-l1-intc";
reg = <0x40000000 0x100>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
interrupt-parent = <&local_intc>;
};
+ };
- arm-pmu {
- compatible = "arm,cortex-a7-pmu";
- interrupt-parent = <&local_intc>;
- interrupts = <9>;
- };
+ arm-pmu {
+ compatible = "arm,cortex-a7-pmu";
+ interrupt-parent = <&local_intc>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
};
timer {
compatible = "arm,armv7-timer";
interrupt-parent = <&local_intc>;
- interrupts = <0>, // PHYS_SECURE_PPI
- <1>, // PHYS_NONSECURE_PPI
- <3>, // VIRT_PPI
- <2>; // HYP_PPI
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>, // PHYS_SECURE_PPI
+ <1 IRQ_TYPE_LEVEL_HIGH>, // PHYS_NONSECURE_PPI
+ <3 IRQ_TYPE_LEVEL_HIGH>, // VIRT_PPI
+ <2 IRQ_TYPE_LEVEL_HIGH>; // HYP_PPI
always-on;
};
compatible = "brcm,bcm2836-armctrl-ic";
reg = <0x7e00b200 0x200>;
interrupt-parent = <&local_intc>;
- interrupts = <8>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
};
&cpu_thermal {
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+ compatible = "raspberrypi,3-model-a-plus", "brcm,bcm2837";
+ model = "Raspberry Pi 3 Model A+";
+
+ chosen {
+ /* 8250 auxiliary UART instead of pl011 */
+ stdout-path = "serial1:115200n8";
+ };
+
+ memory@0 {
+ reg = <0 0x20000000>;
+ };
+
+ leds {
+ act {
+ gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+ };
+
+ pwr {
+ label = "PWR";
+ gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&firmware {
+ expgpio: gpio {
+ compatible = "raspberrypi,firmware-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "",
+ "BT_WL_ON",
+ "STATUS_LED_R",
+ "",
+ "",
+ "CAM_GPIO0",
+ "CAM_GPIO1",
+ "";
+ status = "okay";
+ };
+};
+
+&gpio {
+ /*
+ * This is mostly based on the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "GPIO5",
+ "GPIO6",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "GPIO12",
+ "GPIO13",
+ /* Serial port */
+ "TXD1",
+ "RXD1",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "HDMI_HPD_N",
+ "STATUS_LED_G",
+ /* Used by BT module */
+ "CTS0",
+ "RTS0",
+ "TXD0",
+ "RXD0",
+ /* Used by Wifi */
+ "SD1_CLK",
+ "SD1_CMD",
+ "SD1_DATA0",
+ "SD1_DATA1",
+ "SD1_DATA2",
+ "SD1_DATA3",
+ "PWM0_OUT",
+ "PWM1_OUT",
+ "", /* GPIO42 */
+ "WIFI_CLK",
+ "SDA0",
+ "SCL0",
+ "SMPS_SCL",
+ "SMPS_SDA",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+};
+
+&hdmi {
+ hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+ status = "okay";
+};
+
+/*
+ * SDHCI is used to control the SDIO for wireless
+ *
+ * WL_REG_ON and BT_REG_ON of the CYW43455 Wifi/BT module are driven
+ * by a single GPIO. We can't give GPIO control to one of the drivers,
+ * otherwise the other part would get unexpectedly disturbed.
+ */
+&sdhci {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_gpio34>;
+ status = "okay";
+ bus-width = <4>;
+ non-removable;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhost_gpio48>;
+ status = "okay";
+ bus-width = <4>;
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <2000000>;
+ };
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_gpio14>;
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-lan7515.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+ compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
+ model = "Raspberry Pi 3 Model B+";
+
+ chosen {
+ /* 8250 auxiliary UART instead of pl011 */
+ stdout-path = "serial1:115200n8";
+ };
+
+ memory@0 {
+ reg = <0 0x40000000>;
+ };
+
+ leds {
+ act {
+ gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+ };
+
+ pwr {
+ label = "PWR";
+ gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&firmware {
+ expgpio: gpio {
+ compatible = "raspberrypi,firmware-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "BT_ON",
+ "WL_ON",
+ "STATUS_LED_R",
+ "LAN_RUN",
+ "",
+ "CAM_GPIO0",
+ "CAM_GPIO1",
+ "";
+ status = "okay";
+ };
+};
+
+&gpio {
+ /*
+ * Taken from rpi_SCH_3bplus_1p0_reduced.pdf and
+ * the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "GPIO5",
+ "GPIO6",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "GPIO12",
+ "GPIO13",
+ /* Serial port */
+ "TXD1",
+ "RXD1",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "HDMI_HPD_N",
+ "STATUS_LED_G",
+ /* Used by BT module */
+ "CTS0",
+ "RTS0",
+ "TXD0",
+ "RXD0",
+ /* Used by Wifi */
+ "SD1_CLK",
+ "SD1_CMD",
+ "SD1_DATA0",
+ "SD1_DATA1",
+ "SD1_DATA2",
+ "SD1_DATA3",
+ "PWM0_OUT",
+ "PWM1_OUT",
+ "ETHCLK",
+ "WIFI_CLK",
+ "SDA0",
+ "SCL0",
+ "SMPS_SCL",
+ "SMPS_SDA",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+};
+
+&hdmi {
+ hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+ status = "okay";
+};
+
+/* SDHCI is used to control the SDIO for wireless */
+&sdhci {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_gpio34>;
+ status = "okay";
+ bus-width = <4>;
+ non-removable;
+ mmc-pwrseq = <&wifi_pwrseq>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhost_gpio48>;
+ status = "okay";
+ bus-width = <4>;
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <2000000>;
+ shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_gpio14>;
+ status = "okay";
+};
+// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "bcm2837.dtsi"
-#include "bcm2835-rpi.dtsi"
+#include "bcm2836-rpi.dtsi"
#include "bcm283x-rpi-smsc9514.dtsi"
#include "bcm283x-rpi-usb-host.dtsi"
compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
model = "Raspberry Pi 3 Model B";
- memory {
+ chosen {
+ /* 8250 auxiliary UART instead of pl011 */
+ stdout-path = "serial1:115200n8";
+ };
+
+ memory@0 {
reg = <0 0x40000000>;
};
leds {
act {
- gpios = <&gpio 47 0>;
+ gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>;
};
};
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&firmware {
+ expgpio: gpio {
+ compatible = "raspberrypi,firmware-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "BT_ON",
+ "WL_ON",
+ "STATUS_LED",
+ "LAN_RUN",
+ "HDMI_HPD_N",
+ "CAM_GPIO0",
+ "CAM_GPIO1",
+ "PWR_LOW_N";
+ status = "okay";
+ };
+};
+
+&gpio {
+ /*
+ * Taken from rpi_SCH_3b_1p2_reduced.pdf and
+ * the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "GPIO5",
+ "GPIO6",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "GPIO12",
+ "GPIO13",
+ /* Serial port */
+ "TXD1",
+ "RXD1",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "", /* GPIO 28 */
+ "LAN_RUN_BOOT",
+ /* Used by BT module */
+ "CTS0",
+ "RTS0",
+ "TXD0",
+ "RXD0",
+ /* Used by Wifi */
+ "SD1_CLK",
+ "SD1_CMD",
+ "SD1_DATA0",
+ "SD1_DATA1",
+ "SD1_DATA2",
+ "SD1_DATA3",
+ "PWM0_OUT",
+ "PWM1_OUT",
+ "ETHCLK",
+ "WIFI_CLK",
+ "SDA0",
+ "SCL0",
+ "SMPS_SCL",
+ "SMPS_SDA",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+ status = "okay";
+};
+
+&hdmi {
+ hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>;
};
/* uart0 communicates with the BT module */
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <2000000>;
+ shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+ };
};
/* uart1 is mapped to the pin header */
/* SDHCI is used to control the SDIO for wireless */
&sdhci {
+ #address-cells = <1>;
+ #size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&emmc_gpio34>;
status = "okay";
bus-width = <4>;
non-removable;
+ mmc-pwrseq = <&wifi_pwrseq>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
};
/* SDHOST is used to drive the SD card */
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837-rpi-cm3.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+ compatible = "raspberrypi,3-compute-module", "brcm,bcm2837";
+ model = "Raspberry Pi Compute Module 3 IO board V3.0";
+};
+
+&gpio {
+ /*
+ * This is based on the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "GPIO0",
+ "GPIO1",
+ "GPIO2",
+ "GPIO3",
+ "GPIO4",
+ "GPIO5",
+ "GPIO6",
+ "GPIO7",
+ "GPIO8",
+ "GPIO9",
+ "GPIO10",
+ "GPIO11",
+ "GPIO12",
+ "GPIO13",
+ "GPIO14",
+ "GPIO15",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "GPIO28",
+ "GPIO29",
+ "GPIO30",
+ "GPIO31",
+ "GPIO32",
+ "GPIO33",
+ "GPIO34",
+ "GPIO35",
+ "GPIO36",
+ "GPIO37",
+ "GPIO38",
+ "GPIO39",
+ "GPIO40",
+ "GPIO41",
+ "GPIO42",
+ "GPIO43",
+ "GPIO44",
+ "GPIO45",
+ "GPIO46",
+ "GPIO47",
+ /* Used by eMMC */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
+ pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+ hpd-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio14>;
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+
+/ {
+ memory@0 {
+ reg = <0 0x40000000>;
+ };
+
+ reg_3v3: fixed-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_1v8: fixed-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+};
+
+&firmware {
+ expgpio: gpio {
+ compatible = "raspberrypi,firmware-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "HDMI_HPD_N",
+ "EMMC_EN_N",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC";
+ status = "okay";
+ };
+};
+
+&sdhost {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhost_gpio48>;
+ bus-width = <4>;
+ vmmc-supply = <®_3v3>;
+ vqmmc-supply = <®_1v8>;
+ status = "okay";
+};
<0x40000000 0x40000000 0x00001000>;
dma-ranges = <0xc0000000 0x00000000 0x3f000000>;
- local_intc: local_intc {
+ local_intc: local_intc@40000000 {
compatible = "brcm,bcm2836-l1-intc";
reg = <0x40000000 0x100>;
interrupt-controller;
- #interrupt-cells = <1>;
+ #interrupt-cells = <2>;
interrupt-parent = <&local_intc>;
};
};
+ arm-pmu {
+ compatible = "arm,cortex-a53-pmu";
+ interrupt-parent = <&local_intc>;
+ interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
timer {
compatible = "arm,armv7-timer";
interrupt-parent = <&local_intc>;
- interrupts = <0>, // PHYS_SECURE_PPI
- <1>, // PHYS_NONSECURE_PPI
- <3>, // VIRT_PPI
- <2>; // HYP_PPI
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>, // PHYS_SECURE_PPI
+ <1 IRQ_TYPE_LEVEL_HIGH>, // PHYS_NONSECURE_PPI
+ <3 IRQ_TYPE_LEVEL_HIGH>, // VIRT_PPI
+ <2 IRQ_TYPE_LEVEL_HIGH>; // HYP_PPI
always-on;
};
compatible = "brcm,bcm2836-armctrl-ic";
reg = <0x7e00b200 0x200>;
interrupt-parent = <&local_intc>;
- interrupts = <8>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
};
&cpu_thermal {
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/net/microchip-lan78xx.h>
+
+/ {
+ aliases {
+ ethernet0 = ðernet;
+ };
+};
+
+&usb {
+ usb-port@1 {
+ compatible = "usb424,2514";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb-port@1 {
+ compatible = "usb424,2514";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet: ethernet@1 {
+ compatible = "usb424,7800";
+ reg = <1>;
+
+ mdio {
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ eth_phy: ethernet-phy@1 {
+ reg = <1>;
+ microchip,led-modes = <
+ LAN78XX_LINK_1000_ACTIVITY
+ LAN78XX_LINK_10_100_ACTIVITY
+ >;
+ };
+ };
+ };
+ };
+ };
+};
+// SPDX-License-Identifier: GPL-2.0
/ {
aliases {
ethernet0 = ðernet;
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+&usb {
+ dr_mode = "otg";
+ g-rx-fifo-size = <256>;
+ g-np-tx-fifo-size = <32>;
+ /*
+ * According to dwc2 the sum of all device EP
+ * fifo sizes shouldn't exceed 3776 bytes.
+ */
+ g-tx-fifo-size = <256 256 512 512 512 768 768>;
+};
#include <dt-bindings/clock/bcm2835.h>
#include <dt-bindings/clock/bcm2835-aux.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/soc/bcm2835-pm.h>
/* firmware-provided startup stubs live here, where the secondary CPUs are
* spinning.
#address-cells = <1>;
#size-cells = <1>;
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
chosen {
- bootargs = "earlyprintk console=ttyAMA0";
+ stdout-path = "serial0:115200n8";
};
thermal-zones {
};
};
- soc: soc {
+ soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
clock-frequency = <1000000>;
};
+ txp@7e004000 {
+ compatible = "brcm,bcm2835-txp";
+ reg = <0x7e004000 0x20>;
+ interrupts = <1 11>;
+ };
+
dma: dma@7e007000 {
compatible = "brcm,bcm2835-dma";
reg = <0x7e007000 0xf00>;
#interrupt-cells = <2>;
};
- watchdog@7e100000 {
- compatible = "brcm,bcm2835-pm-wdt";
- reg = <0x7e100000 0x28>;
+ pm: watchdog@7e100000 {
+ compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt";
+ #power-domain-cells = <1>;
+ #reset-cells = <1>;
+ reg = <0x7e100000 0x114>,
+ <0x7e00a000 0x24>;
+ clocks = <&clocks BCM2835_CLOCK_V3D>,
+ <&clocks BCM2835_CLOCK_PERI_IMAGE>,
+ <&clocks BCM2835_CLOCK_H264>,
+ <&clocks BCM2835_CLOCK_ISP>;
+ clock-names = "v3d", "peri_image", "h264", "isp";
+ system-power-controller;
};
clocks: cprman@7e101000 {
rng@7e104000 {
compatible = "brcm,bcm2835-rng";
reg = <0x7e104000 0x10>;
+ interrupts = <2 29>;
};
mailbox: mailbox@7e00b880 {
gpclk2_gpio43: gpclk2_gpio43 {
brcm,pins = <43>;
brcm,function = <BCM2835_FSEL_ALT0>;
+ brcm,pull = <BCM2835_PUD_OFF>;
};
i2c0_gpio0: i2c0_gpio0 {
uart0_ctsrts_gpio30: uart0_ctsrts_gpio30 {
brcm,pins = <30 31>;
brcm,function = <BCM2835_FSEL_ALT3>;
+ brcm,pull = <BCM2835_PUD_UP BCM2835_PUD_OFF>;
};
uart0_gpio32: uart0_gpio32 {
brcm,pins = <32 33>;
brcm,function = <BCM2835_FSEL_ALT3>;
+ brcm,pull = <BCM2835_PUD_OFF BCM2835_PUD_UP>;
};
uart0_gpio36: uart0_gpio36 {
brcm,pins = <36 37>;
i2s: i2s@7e203000 {
compatible = "brcm,bcm2835-i2s";
- reg = <0x7e203000 0x20>,
- <0x7e101098 0x02>;
+ reg = <0x7e203000 0x24>;
+ clocks = <&clocks BCM2835_CLOCK_PCM>;
dmas = <&dma 2>,
<&dma 3>;
interrupts = <2 14>; /* pwa1 */
};
+ dpi: dpi@7e208000 {
+ compatible = "brcm,bcm2835-dpi";
+ reg = <0x7e208000 0x8c>;
+ clocks = <&clocks BCM2835_CLOCK_VPU>,
+ <&clocks BCM2835_CLOCK_DPI>;
+ clock-names = "core", "pixel";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
dsi0: dsi@7e209000 {
compatible = "brcm,bcm2835-dsi0";
reg = <0x7e209000 0x78>;
status = "disabled";
};
- aux: aux@0x7e215000 {
+ aux: aux@7e215000 {
compatible = "brcm,bcm2835-aux";
#clock-cells = <1>;
reg = <0x7e215000 0x8>;
compatible = "brcm,bcm2835-v3d";
reg = <0x7ec00000 0x1000>;
interrupts = <1 10>;
+ power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
};
vc4: gpu {
usbphy: phy {
compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
};
};
-
-#include "bcm283x-uboot.dtsi"
+/* SPDX-License-Identifier: GPL-2.0 */
/*
* Copyright (C) 2015 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
*/
#define BCM2835_AUX_CLOCK_UART 0
+/* SPDX-License-Identifier: GPL-2.0 */
/*
* Copyright (C) 2015 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
*/
#define BCM2835_PLLA 0
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _DT_BINDINGS_MICROCHIP_LAN78XX_H
+#define _DT_BINDINGS_MICROCHIP_LAN78XX_H
+
+/* LED modes for LAN7800/LAN7850 embedded PHY */
+
+#define LAN78XX_LINK_ACTIVITY 0
+#define LAN78XX_LINK_1000_ACTIVITY 1
+#define LAN78XX_LINK_100_ACTIVITY 2
+#define LAN78XX_LINK_10_ACTIVITY 3
+#define LAN78XX_LINK_100_1000_ACTIVITY 4
+#define LAN78XX_LINK_10_1000_ACTIVITY 5
+#define LAN78XX_LINK_10_100_ACTIVITY 6
+#define LAN78XX_DUPLEX_COLLISION 8
+#define LAN78XX_COLLISION 9
+#define LAN78XX_ACTIVITY 10
+#define LAN78XX_AUTONEG_FAULT 12
+#define LAN78XX_FORCE_LED_OFF 14
+#define LAN78XX_FORCE_LED_ON 15
+
+#endif
+/* SPDX-License-Identifier: GPL-2.0 */
/*
* Header providing constants for bcm2835 pinctrl bindings.
*
* Copyright (C) 2015 Stefan Wahren <stefan.wahren@i2se.com>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
*/
#ifndef __DT_BINDINGS_PINCTRL_BCM2835_H__
--- /dev/null
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+
+#ifndef _DT_BINDINGS_ARM_BCM2835_PM_H
+#define _DT_BINDINGS_ARM_BCM2835_PM_H
+
+#define BCM2835_POWER_DOMAIN_GRAFX 0
+#define BCM2835_POWER_DOMAIN_GRAFX_V3D 1
+#define BCM2835_POWER_DOMAIN_IMAGE 2
+#define BCM2835_POWER_DOMAIN_IMAGE_PERI 3
+#define BCM2835_POWER_DOMAIN_IMAGE_ISP 4
+#define BCM2835_POWER_DOMAIN_IMAGE_H264 5
+#define BCM2835_POWER_DOMAIN_USB 6
+#define BCM2835_POWER_DOMAIN_DSI0 7
+#define BCM2835_POWER_DOMAIN_DSI1 8
+#define BCM2835_POWER_DOMAIN_CAM0 9
+#define BCM2835_POWER_DOMAIN_CAM1 10
+#define BCM2835_POWER_DOMAIN_CCP2TX 11
+#define BCM2835_POWER_DOMAIN_HDMI 12
+
+#define BCM2835_POWER_DOMAIN_COUNT 13
+
+#define BCM2835_RESET_V3D 0
+#define BCM2835_RESET_ISP 1
+#define BCM2835_RESET_H264 2
+
+#define BCM2835_RESET_COUNT 3
+
+#endif /* _DT_BINDINGS_ARM_BCM2835_PM_H */
projects / oweals / u-boot.git / commitdiff