include/configs/wandboard.h

   1 /*
   2  * Copyright (C) 2013 Freescale Semiconductor, Inc.
   3  *
   4  * Configuration settings for the Wandboard.
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #ifndef __CONFIG_H
  10 #define __CONFIG_H
  11
  12 #include <config_distro_defaults.h>
  13 #include "mx6_common.h"
  14
  15 #define CONFIG_SPL_LIBCOMMON_SUPPORT
  16 #define CONFIG_SPL_MMC_SUPPORT
  17 #include "imx6_spl.h"
  18
  19 #define MACH_TYPE_WANDBOARD             4412
  20 #define CONFIG_MACH_TYPE                MACH_TYPE_WANDBOARD
  21
  22 /* Size of malloc() pool */
  23 #define CONFIG_SYS_MALLOC_LEN           (10 * SZ_1M)
  24
  25 #define CONFIG_BOARD_EARLY_INIT_F
  26 #define CONFIG_BOARD_LATE_INIT
  27
  28 #define CONFIG_MXC_UART
  29 #define CONFIG_MXC_UART_BASE            UART1_BASE
  30
  31 /* Command definition */
  32 #define CONFIG_CMD_BMODE
  33
  34 #define CONFIG_SYS_MEMTEST_START        0x10000000
  35 #define CONFIG_SYS_MEMTEST_END          (CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)
  36
  37 /* I2C Configs */
  38 #define CONFIG_CMD_I2C
  39 #define CONFIG_SYS_I2C
  40 #define CONFIG_SYS_I2C_MXC
  41 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  42 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  43 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  44 #define CONFIG_SYS_I2C_SPEED            100000
  45
  46 /* MMC Configuration */
  47 #define CONFIG_SYS_FSL_USDHC_NUM        2
  48 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  49
  50 /* USB Configs */
  51 #define CONFIG_CMD_USB
  52 #define CONFIG_USB_EHCI
  53 #define CONFIG_USB_EHCI_MX6
  54 #define CONFIG_USB_STORAGE
  55 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
  56 #define CONFIG_MXC_USB_PORTSC           (PORT_PTS_UTMI | PORT_PTS_PTW)
  57 #define CONFIG_MXC_USB_FLAGS            0
  58
  59 /* Ethernet Configuration */
  60 #define CONFIG_CMD_PING
  61 #define CONFIG_CMD_DHCP
  62 #define CONFIG_CMD_MII
  63 #define CONFIG_FEC_MXC
  64 #define CONFIG_MII
  65 #define IMX_FEC_BASE                    ENET_BASE_ADDR
  66 #define CONFIG_FEC_XCV_TYPE             RGMII
  67 #define CONFIG_ETHPRIME                 "FEC"
  68 #define CONFIG_FEC_MXC_PHYADDR          1
  69 #define CONFIG_PHYLIB
  70 #define CONFIG_PHY_ATHEROS
  71
  72 /* Framebuffer */
  73 #define CONFIG_VIDEO
  74 #define CONFIG_VIDEO_IPUV3
  75 #define CONFIG_CFB_CONSOLE
  76 #define CONFIG_VGA_AS_SINGLE_DEVICE
  77 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
  78 #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
  79 #define CONFIG_VIDEO_BMP_RLE8
  80 #define CONFIG_SPLASH_SCREEN
  81 #define CONFIG_SPLASH_SCREEN_ALIGN
  82 #define CONFIG_BMP_16BPP
  83 #define CONFIG_VIDEO_LOGO
  84 #define CONFIG_VIDEO_BMP_LOGO
  85 #define CONFIG_IPUV3_CLK 260000000
  86 #define CONFIG_CMD_HDMIDETECT
  87 #define CONFIG_IMX_HDMI
  88 #define CONFIG_IMX_VIDEO_SKIP
  89
  90 #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
  91 #define CONFIG_EXTRA_ENV_SETTINGS \
  92         "console=ttymxc0,115200\0" \
  93         "splashpos=m,m\0" \
  94         "fdtfile=undefined\0" \
  95         "fdt_high=0xffffffff\0" \
  96         "initrd_high=0xffffffff\0" \
  97         "fdt_addr_r=0x18000000\0" \
  98         "fdt_addr=0x18000000\0" \
  99         "ip_dyn=yes\0" \
 100         "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
 101         "update_sd_firmware_filename=u-boot.imx\0" \
 102         "update_sd_firmware=" \
 103                 "if test ${ip_dyn} = yes; then " \
 104                         "setenv get_cmd dhcp; " \
 105                 "else " \
 106                         "setenv get_cmd tftp; " \
 107                 "fi; " \
 108                 "if mmc dev ${mmcdev}; then "   \
 109                         "if ${get_cmd} ${update_sd_firmware_filename}; then " \
 110                                 "setexpr fw_sz ${filesize} / 0x200; " \
 111                                 "setexpr fw_sz ${fw_sz} + 1; "  \
 112                                 "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
 113                         "fi; "  \
 114                 "fi\0" \
 115         "videoargs=" \
 116                 "setenv nextcon 0; " \
 117                 "if hdmidet; then " \
 118                         "setenv bootargs ${bootargs} " \
 119                                 "video=mxcfb${nextcon}:dev=hdmi,1280x720M@60," \
 120                                         "if=RGB24; " \
 121                         "setenv fbmen fbmem=28M; " \
 122                         "setexpr nextcon ${nextcon} + 1; " \
 123                 "else " \
 124                         "echo - no HDMI monitor;" \
 125                 "fi; " \
 126                 "i2c dev 1; " \
 127                 "if i2c probe 0x10; then " \
 128                         "setenv bootargs ${bootargs} " \
 129                                 "video=mxcfb${nextcon}:dev=lcd,800x480@60," \
 130                                         "if=RGB666,bpp=32; " \
 131                         "if test 0 -eq ${nextcon}; then " \
 132                                 "setenv fbmem fbmem=10M; " \
 133                         "else " \
 134                                 "setenv fbmem ${fbmem},10M; " \
 135                         "fi; " \
 136                         "setexpr nextcon ${nextcon} + 1; " \
 137                 "else " \
 138                         "echo '- no FWBADAPT-7WVGA-LCD-F07A-0102 display';" \
 139                 "fi; " \
 140                 "setenv bootargs ${bootargs} ${fbmem}\0" \
 141         "findfdt="\
 142                 "if test $board_name = C1 && test $board_rev = MX6Q ; then " \
 143                         "setenv fdtfile imx6q-wandboard.dtb; fi; " \
 144                 "if test $board_name = C1 && test $board_rev = MX6DL ; then " \
 145                         "setenv fdtfile imx6dl-wandboard.dtb; fi; " \
 146                 "if test $board_name = B1 && test $board_rev = MX6Q ; then " \
 147                         "setenv fdtfile imx6q-wandboard-revb1.dtb; fi; " \
 148                 "if test $board_name = B1 && test $board_rev = MX6DL ; then " \
 149                         "setenv fdtfile imx6dl-wandboard-revb1.dtb; fi; " \
 150                 "if test $fdtfile = undefined; then " \
 151                         "echo WARNING: Could not determine dtb to use; fi; \0" \
 152         "kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
 153         "pxe_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
 154         "ramdisk_addr_r=0x13000000\0" \
 155         "ramdiskaddr=0x13000000\0" \
 156         "scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
 157         BOOTENV
 158
 159 #define BOOT_TARGET_DEVICES(func) \
 160         func(MMC, mmc, 0) \
 161         func(MMC, mmc, 1) \
 162         func(USB, usb, 0) \
 163         func(PXE, pxe, na) \
 164         func(DHCP, dhcp, na)
 165
 166 #define CONFIG_BOOTCOMMAND \
 167            "run findfdt; " \
 168            "run distro_bootcmd"
 169
 170 #include <config_distro_bootcmd.h>
 171
 172 /* Physical Memory Map */
 173 #define CONFIG_NR_DRAM_BANKS            1
 174 #define PHYS_SDRAM                      MMDC0_ARB_BASE_ADDR
 175
 176 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM
 177 #define CONFIG_SYS_INIT_RAM_ADDR        IRAM_BASE_ADDR
 178 #define CONFIG_SYS_INIT_RAM_SIZE        IRAM_SIZE
 179
 180 #define CONFIG_SYS_INIT_SP_OFFSET \
 181         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 182 #define CONFIG_SYS_INIT_SP_ADDR \
 183         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 184
 185 /* Environment organization */
 186 #define CONFIG_ENV_SIZE                 (8 * 1024)
 187
 188 #define CONFIG_ENV_IS_IN_MMC
 189 #define CONFIG_ENV_OFFSET               (6 * 64 * 1024)
 190 #define CONFIG_SYS_MMC_ENV_DEV          0
 191
 192 #endif                         /* __CONFIG_H * */