include/configs/tam3517-common.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright (C) 2011
   4  * Stefano Babic, DENX Software Engineering, sbabic@denx.de.
   5  *
   6  * Copyright (C) 2009 TechNexion Ltd.
   7  */
   8
   9 #ifndef __TAM3517_H
  10 #define __TAM3517_H
  11
  12 /*
  13  * High Level Configuration Options
  14  */
  15
  16 #include <asm/arch/cpu.h>               /* get chip and board defs */
  17 #include <asm/arch/omap.h>
  18
  19 /* Clock Defines */
  20 #define V_OSCK                  26000000        /* Clock output from T2 */
  21 #define V_SCLK                  (V_OSCK >> 1)
  22
  23 #define CONFIG_CMDLINE_TAG                      /* enable passing of ATAGs */
  24 #define CONFIG_SETUP_MEMORY_TAGS
  25 #define CONFIG_INITRD_TAG
  26 #define CONFIG_REVISION_TAG
  27
  28 /*
  29  * Size of malloc() pool
  30  */
  31 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + (128 << 10) + \
  32                                         2 * 1024 * 1024)
  33 /*
  34  * DDR related
  35  */
  36 #define CONFIG_SYS_CS0_SIZE             (256 * 1024 * 1024)
  37
  38 /*
  39  * Hardware drivers
  40  */
  41
  42 /*
  43  * NS16550 Configuration
  44  */
  45 #define CONFIG_SYS_NS16550_SERIAL
  46 #define CONFIG_SYS_NS16550_REG_SIZE     (-4)
  47 #define CONFIG_SYS_NS16550_CLK          48000000        /* 48MHz (APLL96/2) */
  48
  49 /*
  50  * select serial console configuration
  51  */
  52 #define CONFIG_SYS_NS16550_COM1         OMAP34XX_UART1
  53
  54 /* allow to overwrite serial and ethaddr */
  55 #define CONFIG_ENV_OVERWRITE
  56 #define CONFIG_SYS_BAUDRATE_TABLE       {4800, 9600, 19200, 38400, 57600,\
  57                                         115200}
  58 /* EHCI */
  59 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO        25
  60
  61 #define CONFIG_SYS_I2C
  62 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50            /* base address */
  63 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1               /* bytes of address */
  64 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW     0x07
  65
  66 /*
  67  * Board NAND Info.
  68  */
  69 #define CONFIG_SYS_NAND_BASE            NAND_BASE       /* physical address */
  70                                                         /* to access */
  71                                                         /* nand at CS0 */
  72
  73 #define CONFIG_SYS_MAX_NAND_DEVICE      1               /* Max number of */
  74                                                         /* NAND devices */
  75
  76 /*
  77  * Miscellaneous configurable options
  78  */
  79 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
  80
  81 #define CONFIG_SYS_MAXARGS              32      /* max number of command */
  82                                                 /* args */
  83 /* memtest works on */
  84
  85 #define CONFIG_SYS_LOAD_ADDR            (OMAP34XX_SDRC_CS0) /* default load */
  86                                                                 /* address */
  87
  88 /*
  89  * AM3517 has 12 GP timers, they can be driven by the system clock
  90  * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
  91  * This rate is divided by a local divisor.
  92  */
  93 #define CONFIG_SYS_TIMERBASE            OMAP34XX_GPT2
  94 #define CONFIG_SYS_PTV                  2       /* Divisor: 2^(PTV+1) => 8 */
  95
  96 /*
  97  * Physical Memory Map
  98  */
  99 #define PHYS_SDRAM_1            OMAP34XX_SDRC_CS0
 100 #define PHYS_SDRAM_2            OMAP34XX_SDRC_CS1
 101
 102 /*
 103  * FLASH and environment organization
 104  */
 105
 106 /* **** PISMO SUPPORT *** */
 107
 108 /* Redundant Environment */
 109 #define CONFIG_SYS_ENV_SECT_SIZE        (128 << 10)     /* 128 KiB */
 110
 111 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM_1
 112 #define CONFIG_SYS_INIT_RAM_ADDR        0x4020f800
 113 #define CONFIG_SYS_INIT_RAM_SIZE        0x800
 114 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_INIT_RAM_ADDR + \
 115                                          CONFIG_SYS_INIT_RAM_SIZE - \
 116                                          GENERATED_GBL_DATA_SIZE)
 117
 118 /*
 119  * ethernet support, EMAC
 120  *
 121  */
 122 #define CONFIG_DRIVER_TI_EMAC_USE_RMII
 123 #define CONFIG_BOOTP_DNS2
 124 #define CONFIG_BOOTP_SEND_HOSTNAME
 125 #define CONFIG_NET_RETRY_COUNT 10
 126
 127 /* Defines for SPL */
 128 #define CONFIG_SPL_CONSOLE
 129 #define CONFIG_SPL_NAND_SOFTECC
 130 #define CONFIG_SPL_NAND_WORKSPACE       0x8f07f000 /* below BSS */
 131
 132 #define CONFIG_SPL_NAND_BASE
 133 #define CONFIG_SPL_NAND_DRIVERS
 134 #define CONFIG_SPL_NAND_ECC
 135
 136 #define CONFIG_SPL_MAX_SIZE             (SRAM_SCRATCH_SPACE_ADDR - \
 137                                          CONFIG_SPL_TEXT_BASE)
 138 #define CONFIG_SPL_STACK                LOW_LEVEL_SRAM_STACK
 139
 140 #define CONFIG_SYS_SPL_MALLOC_START     0x8f000000
 141 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x80000
 142 #define CONFIG_SPL_BSS_START_ADDR       0x8f080000 /* end of RAM */
 143 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
 144
 145 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION      1
 146 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME         "u-boot.img"
 147
 148 /* FAT */
 149 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME          "uImage"
 150 #define CONFIG_SPL_FS_LOAD_ARGS_NAME            "args"
 151
 152 /* RAW SD card / eMMC */
 153 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900   /* address 0x120000 */
 154 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR   0x80    /* address 0x10000 */
 155 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS  0x80    /* 64KiB */
 156
 157 /* NAND boot config */
 158 #define CONFIG_SYS_NAND_PAGE_COUNT      64
 159 #define CONFIG_SYS_NAND_PAGE_SIZE       2048
 160 #define CONFIG_SYS_NAND_OOBSIZE         64
 161 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 162 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 163 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   0
 164 #define CONFIG_SYS_NAND_ECCPOS          {40, 41, 42, 43, 44, 45, 46, 47,\
 165                                          48, 49, 50, 51, 52, 53, 54, 55,\
 166                                          56, 57, 58, 59, 60, 61, 62, 63}
 167 #define CONFIG_SYS_NAND_ECCSIZE         256
 168 #define CONFIG_SYS_NAND_ECCBYTES        3
 169 #define CONFIG_NAND_OMAP_ECCSCHEME      OMAP_ECC_HAM1_CODE_SW
 170
 171 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
 172
 173 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x80000
 174 #define CONFIG_SYS_NAND_U_BOOT_SIZE     0x80000
 175
 176 /* Setup MTD for NAND on the SOM */
 177
 178 #define CONFIG_TAM3517_SETTINGS                                         \
 179         "netdev=eth0\0"                                                 \
 180         "nandargs=setenv bootargs root=${nandroot} "                    \
 181                 "rootfstype=${nandrootfstype}\0"                        \
 182         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 183                 "nfsroot=${serverip}:${rootpath}\0"                     \
 184         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 185         "addip_sta=setenv bootargs ${bootargs} "                        \
 186                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 187                 ":${hostname}:${netdev}:off panic=1\0"                  \
 188         "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0"               \
 189         "addip=if test -n ${ipdyn};then run addip_dyn;"                 \
 190                 "else run addip_sta;fi\0"                               \
 191         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
 192         "addtty=setenv bootargs ${bootargs}"                            \
 193                 " console=ttyO0,${baudrate}\0"                          \
 194         "addmisc=setenv bootargs ${bootargs} ${misc}\0"                 \
 195         "loadaddr=82000000\0"                                           \
 196         "kernel_addr_r=82000000\0"                                      \
 197         "hostname=" CONFIG_HOSTNAME "\0"                        \
 198         "bootfile=" CONFIG_HOSTNAME "/uImage\0"         \
 199         "flash_self=run ramargs addip addtty addmtd addmisc;"           \
 200                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 201         "flash_nfs=run nfsargs addip addtty addmtd addmisc;"            \
 202                 "bootm ${kernel_addr}\0"                                \
 203         "nandboot=run nandargs addip addtty addmtd addmisc;"            \
 204                 "nand read ${kernel_addr_r} kernel\0"                   \
 205                 "bootm ${kernel_addr_r}\0"                              \
 206         "net_nfs=tftp ${kernel_addr_r} ${bootfile}; "                   \
 207                 "run nfsargs addip addtty addmtd addmisc;"              \
 208                 "bootm ${kernel_addr_r}\0"                              \
 209         "net_self=if run net_self_load;then "                           \
 210                 "run ramargs addip addtty addmtd addmisc;"              \
 211                 "bootm ${kernel_addr_r} ${ramdisk_addr_r};"             \
 212                 "else echo Images not loades;fi\0"                      \
 213         "u-boot=" CONFIG_HOSTNAME "/u-boot.img\0"               \
 214         "load=tftp ${loadaddr} ${u-boot}\0"                             \
 215         "loadmlo=tftp ${loadaddr} ${mlo}\0"                             \
 216         "mlo=" CONFIG_HOSTNAME "/MLO\0"                 \
 217         "uboot_addr=0x80000\0"                                          \
 218         "update=nandecc sw;nand erase ${uboot_addr} 100000;"            \
 219                 "nand write ${loadaddr} ${uboot_addr} 80000\0"          \
 220         "updatemlo=nandecc hw;nand erase 0 20000;"                      \
 221                 "nand write ${loadaddr} 0 20000\0"                      \
 222         "upd=if run load;then echo Updating u-boot;if run update;"      \
 223                 "then echo U-Boot updated;"                             \
 224                         "else echo Error updating u-boot !;"            \
 225                         "echo Board without bootloader !!;"             \
 226                 "fi;"                                                   \
 227                 "else echo U-Boot not downloaded..exiting;fi\0"         \
 228
 229 /*
 230  * this is common code for all TAM3517 boards.
 231  * MAC address is stored from manufacturer in
 232  * I2C EEPROM
 233  */
 234 #if !(defined(__KERNEL_STRICT_NAMES) || defined(__ASSEMBLY__))
 235 /*
 236  * The I2C EEPROM on the TAM3517 contains
 237  * mac address and production data
 238  */
 239 struct tam3517_module_info {
 240         char customer[48];
 241         char product[48];
 242
 243         /*
 244          * bit 0~47  : sequence number
 245          * bit 48~55 : week of year, from 0.
 246          * bit 56~63 : year
 247          */
 248         unsigned long long sequence_number;
 249
 250         /*
 251          * bit 0~7   : revision fixed
 252          * bit 8~15  : revision major
 253          * bit 16~31 : TNxxx
 254          */
 255         unsigned int revision;
 256         unsigned char eth_addr[4][8];
 257         unsigned char _rev[100];
 258 };
 259
 260 #define TAM3517_READ_EEPROM(info, ret) \
 261 do {                                                            \
 262         i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); \
 263         if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,          \
 264                 (void *)info, sizeof(*info)))                   \
 265                 ret = 1;                                        \
 266         else                                                    \
 267                 ret = 0;                                        \
 268 } while (0)
 269
 270 #define TAM3517_READ_MAC_FROM_EEPROM(info)                      \
 271 do {                                                            \
 272         char buf[80], ethname[20];                              \
 273         int i;                                                  \
 274         memset(buf, 0, sizeof(buf));                            \
 275         for (i = 0 ; i < ARRAY_SIZE((info)->eth_addr); i++) {   \
 276                 sprintf(buf, "%02X:%02X:%02X:%02X:%02X:%02X",   \
 277                         (info)->eth_addr[i][5],                 \
 278                         (info)->eth_addr[i][4],                 \
 279                         (info)->eth_addr[i][3],                 \
 280                         (info)->eth_addr[i][2],                 \
 281                         (info)->eth_addr[i][1],                 \
 282                         (info)->eth_addr[i][0]);                        \
 283                                                                 \
 284                 if (i)                                          \
 285                         sprintf(ethname, "eth%daddr", i);       \
 286                 else                                            \
 287                         strcpy(ethname, "ethaddr");             \
 288                 printf("Setting %s from EEPROM with %s\n", ethname, buf);\
 289                 env_set(ethname, buf);                          \
 290         }                                                       \
 291 } while (0)
 292
 293 /* The following macros are taken from Technexion's documentation */
 294 #define TAM3517_sequence_number(info) \
 295         ((info)->sequence_number % 0x1000000000000LL)
 296 #define TAM3517_week_of_year(info) (((info)->sequence_number >> 48) % 0x100)
 297 #define TAM3517_year(info) ((info)->sequence_number >> 56)
 298 #define TAM3517_revision_fixed(info) ((info)->revision % 0x100)
 299 #define TAM3517_revision_major(info) (((info)->revision >> 8) % 0x100)
 300 #define TAM3517_revision_tn(info) ((info)->revision >> 16)
 301
 302 #define TAM3517_PRINT_SOM_INFO(info)                            \
 303 do {                                                            \
 304         printf("Vendor:%s\n", (info)->customer);                \
 305         printf("SOM:   %s\n", (info)->product);                 \
 306         printf("SeqNr: %02llu%02llu%012llu\n",                  \
 307                 TAM3517_year(info),                             \
 308                 TAM3517_week_of_year(info),                     \
 309                 TAM3517_sequence_number(info));                 \
 310         printf("Rev:   TN%u %u.%u\n",                           \
 311                 TAM3517_revision_tn(info),                      \
 312                 TAM3517_revision_major(info),                   \
 313                 TAM3517_revision_fixed(info));                  \
 314 } while (0)
 315
 316 #endif
 317
 318 #endif /* __TAM3517_H */