include/configs/omapl138_lcdk.h

   1 /* SPDX-License-Identifier: GPL-2.0 */
   2 /*
   3  * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
   4  *
   5  * Based on davinci_dvevm.h. Original Copyrights follow:
   6  *
   7  * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
   8  */
   9
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 /*
  14  * Board
  15  */
  16 #undef CONFIG_USE_SPIFLASH
  17 #undef  CONFIG_SYS_USE_NOR
  18
  19 /*
  20 * Disable DM_* for SPL build and can be re-enabled after adding
  21 * DM support in SPL
  22 */
  23 #ifdef CONFIG_SPL_BUILD
  24 #undef CONFIG_DM_I2C
  25 #undef CONFIG_DM_I2C_COMPAT
  26 #endif
  27 /*
  28  * SoC Configuration
  29  */
  30 #define CONFIG_MACH_OMAPL138_LCDK
  31 #define CONFIG_SYS_CLK_FREQ             clk_get(DAVINCI_ARM_CLKID)
  32 #define CONFIG_SYS_OSCIN_FREQ           24000000
  33 #define CONFIG_SYS_TIMERBASE            DAVINCI_TIMER0_BASE
  34 #define CONFIG_SYS_HZ_CLOCK             clk_get(DAVINCI_AUXCLK_CLKID)
  35 #define CONFIG_SYS_HZ                   1000
  36 #define CONFIG_SKIP_LOWLEVEL_INIT
  37
  38 /*
  39  * Memory Info
  40  */
  41 #define CONFIG_SYS_MALLOC_LEN   (0x10000 + 1*1024*1024) /* malloc() len */
  42 #define PHYS_SDRAM_1            DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
  43 #define PHYS_SDRAM_1_SIZE       (128 << 20) /* SDRAM size 128MB */
  44 #define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
  45
  46 /* memtest start addr */
  47 #define CONFIG_SYS_MEMTEST_START        (PHYS_SDRAM_1 + 0x2000000)
  48
  49 /* memtest will be run on 16MB */
  50 #define CONFIG_SYS_MEMTEST_END  (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024)
  51
  52 #define CONFIG_SYS_DA850_SYSCFG_SUSPSRC (       \
  53         DAVINCI_SYSCFG_SUSPSRC_TIMER0 |         \
  54         DAVINCI_SYSCFG_SUSPSRC_SPI1 |           \
  55         DAVINCI_SYSCFG_SUSPSRC_UART2 |          \
  56         DAVINCI_SYSCFG_SUSPSRC_EMAC |           \
  57         DAVINCI_SYSCFG_SUSPSRC_I2C)
  58
  59 /*
  60  * PLL configuration
  61  */
  62
  63 /* Requires CONFIG_SYS_DA850_PLL0_POSTDIV=0, set in Kconfig */
  64 #define CONFIG_SYS_DA850_PLL0_PLLM     18
  65 #define CONFIG_SYS_DA850_PLL1_PLLM     21
  66
  67 /*
  68  * DDR2 memory configuration
  69  */
  70 #define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \
  71                                         DV_DDR_PHY_EXT_STRBEN | \
  72                                         (0x5 << DV_DDR_PHY_RD_LATENCY_SHIFT))
  73
  74 #define CONFIG_SYS_DA850_DDR2_SDBCR (             \
  75         (1 << DV_DDR_SDCR_DDR2EN_SHIFT)         | \
  76         (1 << DV_DDR_SDCR_DDREN_SHIFT)          | \
  77         (1 << DV_DDR_SDCR_SDRAMEN_SHIFT)        | \
  78         (1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT)      | \
  79         (4 << DV_DDR_SDCR_CL_SHIFT)             | \
  80         (3 << DV_DDR_SDCR_IBANK_SHIFT)          | \
  81         (2 << DV_DDR_SDCR_PAGESIZE_SHIFT))
  82
  83 /* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */
  84 #define CONFIG_SYS_DA850_DDR2_SDBCR2 0
  85
  86 #define CONFIG_SYS_DA850_DDR2_SDTIMR (            \
  87         (19 << DV_DDR_SDTMR1_RFC_SHIFT)         | \
  88         (1 << DV_DDR_SDTMR1_RP_SHIFT)           | \
  89         (1 << DV_DDR_SDTMR1_RCD_SHIFT)          | \
  90         (2 << DV_DDR_SDTMR1_WR_SHIFT)           | \
  91         (6 << DV_DDR_SDTMR1_RAS_SHIFT)          | \
  92         (8 << DV_DDR_SDTMR1_RC_SHIFT)           | \
  93         (1 << DV_DDR_SDTMR1_RRD_SHIFT)          | \
  94         (1 << DV_DDR_SDTMR1_WTR_SHIFT))
  95
  96 #define CONFIG_SYS_DA850_DDR2_SDTIMR2 (           \
  97         (7 << DV_DDR_SDTMR2_RASMAX_SHIFT)       | \
  98         (2 << DV_DDR_SDTMR2_XP_SHIFT)           | \
  99         (0 << DV_DDR_SDTMR2_ODT_SHIFT)          | \
 100         (20 << DV_DDR_SDTMR2_XSNR_SHIFT)        | \
 101         (199 << DV_DDR_SDTMR2_XSRD_SHIFT)       | \
 102         (1 << DV_DDR_SDTMR2_RTP_SHIFT)          | \
 103         (2 << DV_DDR_SDTMR2_CKE_SHIFT))
 104
 105 #define CONFIG_SYS_DA850_DDR2_SDRCR    0x00000492
 106 #define CONFIG_SYS_DA850_DDR2_PBBPR    0x30
 107
 108 /*
 109  * Serial Driver info
 110  */
 111 #define CONFIG_SYS_NS16550_CLK  clk_get(DAVINCI_UART2_CLKID)
 112 #if !defined(CONFIG_DM_SERIAL)
 113 #define CONFIG_SYS_NS16550_SERIAL
 114 #define CONFIG_SYS_NS16550_REG_SIZE     -4      /* NS16550 register size */
 115 #define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */
 116 #define CONFIG_SYS_NS16550_CLK  clk_get(DAVINCI_UART2_CLKID)
 117 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
 118 #endif
 119
 120 #define CONFIG_SYS_SPI_BASE             DAVINCI_SPI1_BASE
 121 #define CONFIG_SYS_SPI_CLK              clk_get(DAVINCI_SPI1_CLKID)
 122 #define CONFIG_ENV_SPI_MAX_HZ   CONFIG_SF_DEFAULT_SPEED
 123
 124 #ifdef CONFIG_USE_SPIFLASH
 125 #define CONFIG_SYS_SPI_U_BOOT_OFFS      0x8000
 126 #define CONFIG_SYS_SPI_U_BOOT_SIZE      0x30000
 127 #endif
 128
 129 /*
 130  * I2C Configuration
 131  */
 132 #define CONFIG_SYS_DAVINCI_I2C_SPEED    25000
 133 #define CONFIG_SYS_DAVINCI_I2C_SLAVE    10 /* Bogus, master-only in U-Boot */
 134 #define CONFIG_SYS_I2C_EXPANDER_ADDR    0x20
 135
 136 /*
 137  * Flash & Environment
 138  */
 139 #ifdef CONFIG_NAND
 140 #define CONFIG_ENV_OFFSET               0x0 /* Block 0--not used by bootcode */
 141 #define CONFIG_ENV_SIZE                 (128 << 9)
 142 #define CONFIG_SYS_NAND_USE_FLASH_BBT
 143 #define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
 144 #define CONFIG_SYS_NAND_PAGE_2K
 145 #define CONFIG_SYS_NAND_CS              3
 146 #define CONFIG_SYS_NAND_BASE            DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
 147 #define CONFIG_SYS_NAND_MASK_CLE        0x10
 148 #define CONFIG_SYS_NAND_MASK_ALE        0x8
 149 #undef CONFIG_SYS_NAND_HW_ECC
 150 #define CONFIG_SYS_MAX_NAND_DEVICE      1 /* Max number of NAND devices */
 151 #define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
 152 #define CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
 153 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 154 #define CONFIG_SYS_NAND_PAGE_SIZE       (2 << 10)
 155 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 << 10)
 156 #define CONFIG_SYS_NAND_U_BOOT_SIZE     SZ_512K
 157 #define CONFIG_SYS_NAND_U_BOOT_DST      0xc1080000
 158 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_NAND_U_BOOT_DST
 159 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \
 160                                         CONFIG_SYS_NAND_U_BOOT_SIZE - \
 161                                         CONFIG_SYS_MALLOC_LEN -       \
 162                                         GENERATED_GBL_DATA_SIZE)
 163 #define CONFIG_SYS_NAND_ECCPOS          {                               \
 164                                 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,     \
 165                                 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, \
 166                                 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, \
 167                                 54, 55, 56, 57, 58, 59, 60, 61, 62, 63 }
 168 #define CONFIG_SYS_NAND_PAGE_COUNT      64
 169 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   0
 170 #define CONFIG_SYS_NAND_ECCSIZE         512
 171 #define CONFIG_SYS_NAND_ECCBYTES        10
 172 #define CONFIG_SYS_NAND_OOBSIZE         64
 173 #define CONFIG_SPL_NAND_BASE
 174 #define CONFIG_SPL_NAND_DRIVERS
 175 #define CONFIG_SPL_NAND_ECC
 176 #define CONFIG_SPL_NAND_LOAD
 177 #endif
 178
 179 #ifdef CONFIG_SYS_USE_NOR
 180 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* max number of flash banks */
 181 #define CONFIG_SYS_FLASH_SECT_SZ        (128 << 10) /* 128KB */
 182 #define CONFIG_ENV_OFFSET               (CONFIG_SYS_FLASH_SECT_SZ * 3)
 183 #define CONFIG_ENV_SIZE                 (128 << 10)
 184 #define CONFIG_SYS_FLASH_BASE           DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
 185 #define PHYS_FLASH_SIZE                 (8 << 20) /* Flash size 8MB */
 186 #define CONFIG_SYS_MAX_FLASH_SECT ((PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)\
 187                + 3)
 188 #define CONFIG_ENV_SECT_SIZE            CONFIG_SYS_FLASH_SECT_SZ
 189 #endif
 190
 191 #ifdef CONFIG_USE_SPIFLASH
 192 #define CONFIG_ENV_SIZE                 (64 << 10)
 193 #define CONFIG_ENV_OFFSET               (256 << 10)
 194 #define CONFIG_ENV_SECT_SIZE            (64 << 10)
 195 #endif
 196
 197 /*
 198  * Network & Ethernet Configuration
 199  */
 200 #ifdef CONFIG_DRIVER_TI_EMAC
 201 #undef  CONFIG_DRIVER_TI_EMAC_USE_RMII
 202 #define CONFIG_BOOTP_DEFAULT
 203 #define CONFIG_BOOTP_DNS2
 204 #define CONFIG_BOOTP_SEND_HOSTNAME
 205 #define CONFIG_NET_RETRY_COUNT  10
 206 #endif
 207
 208 /*
 209  * U-Boot general configuration
 210  */
 211 #define CONFIG_BOOTFILE         "zImage" /* Boot file name */
 212 #define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */
 213 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
 214 #define CONFIG_SYS_LOAD_ADDR    (PHYS_SDRAM_1 + 0x700000)
 215 #define CONFIG_MX_CYCLIC
 216
 217 /*
 218  * Linux Information
 219  */
 220 #define LINUX_BOOT_PARAM_ADDR   (PHYS_SDRAM_1 + 0x100)
 221 #define CONFIG_CMDLINE_TAG
 222 #define CONFIG_REVISION_TAG
 223 #define CONFIG_SETUP_MEMORY_TAGS
 224 #define CONFIG_BOOTCOMMAND \
 225                 "run envboot; " \
 226                 "run mmcboot; "
 227
 228 #define DEFAULT_LINUX_BOOT_ENV \
 229         "loadaddr=0xc0700000\0" \
 230         "fdtaddr=0xc0600000\0" \
 231         "scriptaddr=0xc0600000\0"
 232
 233 #include <environment/ti/mmc.h>
 234
 235 #define CONFIG_EXTRA_ENV_SETTINGS \
 236         DEFAULT_LINUX_BOOT_ENV \
 237         DEFAULT_MMC_TI_ARGS \
 238         "bootpart=0:2\0" \
 239         "bootdir=/boot\0" \
 240         "bootfile=zImage\0" \
 241         "fdtfile=da850-lcdk.dtb\0" \
 242         "boot_fdt=yes\0" \
 243         "boot_fit=0\0" \
 244         "console=ttyS2,115200n8\0"
 245
 246 #ifdef CONFIG_CMD_BDI
 247 #define CONFIG_CLOCKS
 248 #endif
 249
 250 #if !defined(CONFIG_NAND) && \
 251         !defined(CONFIG_SYS_USE_NOR) && \
 252         !defined(CONFIG_USE_SPIFLASH)
 253 #define CONFIG_ENV_SIZE         (16 << 10)
 254 #endif
 255
 256 /* SD/MMC */
 257
 258 #ifdef CONFIG_ENV_IS_IN_MMC
 259 #undef CONFIG_ENV_SIZE
 260 #undef CONFIG_ENV_OFFSET
 261 #define CONFIG_ENV_SIZE         (16 << 10)      /* 16 KiB */
 262 #define CONFIG_ENV_OFFSET       (51 << 9)       /* Sector 51 */
 263 #endif
 264
 265 #ifndef CONFIG_DIRECT_NOR_BOOT
 266 /* defines for SPL */
 267 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SYS_TEXT_BASE - \
 268                                                 CONFIG_SYS_MALLOC_LEN)
 269 #define CONFIG_SYS_SPL_MALLOC_SIZE      CONFIG_SYS_MALLOC_LEN
 270 #define CONFIG_SPL_STACK        0x8001ff00
 271 #define CONFIG_SPL_TEXT_BASE    0x80000000
 272 #define CONFIG_SPL_MAX_FOOTPRINT        32768
 273 #define CONFIG_SPL_PAD_TO       32768
 274 #endif
 275
 276 /* additions for new relocation code, must added to all boards */
 277 #define CONFIG_SYS_SDRAM_BASE           0xc0000000
 278 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
 279                                         GENERATED_GBL_DATA_SIZE)
 280
 281 #include <asm/arch/hardware.h>
 282
 283 #endif /* __CONFIG_H */