include/configs/omapl138_lcdk.h

   1 /* SPDX-License-Identifier: GPL-2.0 */
   2 /*
   3  * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
   4  *
   5  * Based on davinci_dvevm.h. Original Copyrights follow:
   6  *
   7  * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
   8  */
   9
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 /*
  14  * Board
  15  */
  16
  17 /*
  18  * SoC Configuration
  19  */
  20 #define CONFIG_MACH_OMAPL138_LCDK
  21 #define CONFIG_SYS_CLK_FREQ             clk_get(DAVINCI_ARM_CLKID)
  22 #define CONFIG_SYS_OSCIN_FREQ           24000000
  23 #define CONFIG_SYS_TIMERBASE            DAVINCI_TIMER0_BASE
  24 #define CONFIG_SYS_HZ_CLOCK             clk_get(DAVINCI_AUXCLK_CLKID)
  25 #define CONFIG_SYS_HZ                   1000
  26 #define CONFIG_SKIP_LOWLEVEL_INIT_ONLY
  27
  28 /*
  29  * Memory Info
  30  */
  31 #define CONFIG_SYS_MALLOC_LEN   (0x10000 + 1*1024*1024) /* malloc() len */
  32 #define PHYS_SDRAM_1            DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
  33 #define PHYS_SDRAM_1_SIZE       (128 << 20) /* SDRAM size 128MB */
  34 #define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
  35
  36 #define CONFIG_SPL_BSS_START_ADDR DAVINCI_DDR_EMIF_DATA_BASE
  37 #define CONFIG_SPL_BSS_MAX_SIZE 0x1080000
  38
  39 /* memtest start addr */
  40
  41 /* memtest will be run on 16MB */
  42
  43 #define CONFIG_SYS_DA850_SYSCFG_SUSPSRC (       \
  44         DAVINCI_SYSCFG_SUSPSRC_TIMER0 |         \
  45         DAVINCI_SYSCFG_SUSPSRC_SPI1 |           \
  46         DAVINCI_SYSCFG_SUSPSRC_UART2 |          \
  47         DAVINCI_SYSCFG_SUSPSRC_EMAC |           \
  48         DAVINCI_SYSCFG_SUSPSRC_I2C)
  49
  50 /*
  51  * PLL configuration
  52  */
  53
  54 /* Requires CONFIG_SYS_DA850_PLL0_POSTDIV=0, set in Kconfig */
  55 #define CONFIG_SYS_DA850_PLL0_PLLM     18
  56 #define CONFIG_SYS_DA850_PLL1_PLLM     21
  57
  58 /*
  59  * DDR2 memory configuration
  60  */
  61 #define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \
  62                                         DV_DDR_PHY_EXT_STRBEN | \
  63                                         (0x5 << DV_DDR_PHY_RD_LATENCY_SHIFT))
  64
  65 #define CONFIG_SYS_DA850_DDR2_SDBCR (             \
  66         (1 << DV_DDR_SDCR_DDR2EN_SHIFT)         | \
  67         (1 << DV_DDR_SDCR_DDREN_SHIFT)          | \
  68         (1 << DV_DDR_SDCR_SDRAMEN_SHIFT)        | \
  69         (1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT)      | \
  70         (4 << DV_DDR_SDCR_CL_SHIFT)             | \
  71         (3 << DV_DDR_SDCR_IBANK_SHIFT)          | \
  72         (2 << DV_DDR_SDCR_PAGESIZE_SHIFT))
  73
  74 /* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */
  75 #define CONFIG_SYS_DA850_DDR2_SDBCR2 0
  76
  77 #define CONFIG_SYS_DA850_DDR2_SDTIMR (            \
  78         (19 << DV_DDR_SDTMR1_RFC_SHIFT)         | \
  79         (1 << DV_DDR_SDTMR1_RP_SHIFT)           | \
  80         (1 << DV_DDR_SDTMR1_RCD_SHIFT)          | \
  81         (2 << DV_DDR_SDTMR1_WR_SHIFT)           | \
  82         (6 << DV_DDR_SDTMR1_RAS_SHIFT)          | \
  83         (8 << DV_DDR_SDTMR1_RC_SHIFT)           | \
  84         (1 << DV_DDR_SDTMR1_RRD_SHIFT)          | \
  85         (1 << DV_DDR_SDTMR1_WTR_SHIFT))
  86
  87 #define CONFIG_SYS_DA850_DDR2_SDTIMR2 (           \
  88         (7 << DV_DDR_SDTMR2_RASMAX_SHIFT)       | \
  89         (2 << DV_DDR_SDTMR2_XP_SHIFT)           | \
  90         (0 << DV_DDR_SDTMR2_ODT_SHIFT)          | \
  91         (20 << DV_DDR_SDTMR2_XSNR_SHIFT)        | \
  92         (199 << DV_DDR_SDTMR2_XSRD_SHIFT)       | \
  93         (1 << DV_DDR_SDTMR2_RTP_SHIFT)          | \
  94         (2 << DV_DDR_SDTMR2_CKE_SHIFT))
  95
  96 #define CONFIG_SYS_DA850_DDR2_SDRCR    0x00000492
  97 #define CONFIG_SYS_DA850_DDR2_PBBPR    0x30
  98
  99 /*
 100  * Serial Driver info
 101  */
 102 #define CONFIG_SYS_NS16550_CLK  clk_get(DAVINCI_UART2_CLKID)
 103
 104 #define CONFIG_SYS_SPI_BASE             DAVINCI_SPI1_BASE
 105 #define CONFIG_SYS_SPI_CLK              clk_get(DAVINCI_SPI1_CLKID)
 106
 107 /*
 108  * I2C Configuration
 109  */
 110 #define CONFIG_SYS_DAVINCI_I2C_SPEED    25000
 111 #define CONFIG_SYS_DAVINCI_I2C_SLAVE    10 /* Bogus, master-only in U-Boot */
 112 #define CONFIG_SYS_I2C_EXPANDER_ADDR    0x20
 113
 114 /*
 115  * Flash & Environment
 116  */
 117 #ifdef CONFIG_MTD_RAW_NAND
 118 #define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
 119 #define CONFIG_SYS_NAND_PAGE_2K
 120 #define CONFIG_SYS_NAND_CS              3
 121 #define CONFIG_SYS_NAND_BASE            DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
 122 #define CONFIG_SYS_NAND_MASK_CLE        0x10
 123 #define CONFIG_SYS_NAND_MASK_ALE        0x8
 124 #undef CONFIG_SYS_NAND_HW_ECC
 125 #define CONFIG_SYS_MAX_NAND_DEVICE      1 /* Max number of NAND devices */
 126 #define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
 127 #define CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
 128 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 129 #define CONFIG_SYS_NAND_PAGE_SIZE       (2 << 10)
 130 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 << 10)
 131 #define CONFIG_SYS_NAND_U_BOOT_SIZE     SZ_512K
 132 #define CONFIG_SYS_NAND_U_BOOT_DST      0xc1080000
 133 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_NAND_U_BOOT_DST
 134 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \
 135                                         CONFIG_SYS_NAND_U_BOOT_SIZE - \
 136                                         CONFIG_SYS_MALLOC_LEN -       \
 137                                         GENERATED_GBL_DATA_SIZE)
 138 #define CONFIG_SYS_NAND_ECCPOS          {                               \
 139                                 6, 7, 8, 9, 10, 11, 12, 13, 14, 15,     \
 140                                 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, \
 141                                 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, \
 142                                 54, 55, 56, 57, 58, 59, 60, 61, 62, 63 }
 143 #define CONFIG_SYS_NAND_PAGE_COUNT      64
 144 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   0
 145 #define CONFIG_SYS_NAND_ECCSIZE         512
 146 #define CONFIG_SYS_NAND_ECCBYTES        10
 147 #define CONFIG_SYS_NAND_OOBSIZE         64
 148 #define CONFIG_SPL_NAND_BASE
 149 #define CONFIG_SPL_NAND_DRIVERS
 150 #define CONFIG_SPL_NAND_ECC
 151 #define CONFIG_SPL_NAND_LOAD
 152 #endif
 153
 154 /*
 155  * Network & Ethernet Configuration
 156  */
 157 #ifdef CONFIG_DRIVER_TI_EMAC
 158 #undef  CONFIG_DRIVER_TI_EMAC_USE_RMII
 159 #define CONFIG_BOOTP_DEFAULT
 160 #define CONFIG_BOOTP_DNS2
 161 #define CONFIG_BOOTP_SEND_HOSTNAME
 162 #define CONFIG_NET_RETRY_COUNT  10
 163 #endif
 164
 165 /*
 166  * U-Boot general configuration
 167  */
 168 #define CONFIG_BOOTFILE         "zImage" /* Boot file name */
 169 #define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */
 170 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
 171 #define CONFIG_SYS_LOAD_ADDR    (PHYS_SDRAM_1 + 0x700000)
 172
 173 /*
 174  * USB Configs
 175  */
 176 #define CONFIG_USB_OHCI_NEW
 177 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS      15
 178
 179 /*
 180  * Linux Information
 181  */
 182 #define LINUX_BOOT_PARAM_ADDR   (PHYS_SDRAM_1 + 0x100)
 183 #define CONFIG_CMDLINE_TAG
 184 #define CONFIG_REVISION_TAG
 185 #define CONFIG_SETUP_MEMORY_TAGS
 186 #define CONFIG_BOOTCOMMAND \
 187                 "run envboot; " \
 188                 "run mmcboot; "
 189
 190 #define DEFAULT_LINUX_BOOT_ENV \
 191         "loadaddr=0xc0700000\0" \
 192         "fdtaddr=0xc0600000\0" \
 193         "scriptaddr=0xc0600000\0"
 194
 195 #include <environment/ti/mmc.h>
 196
 197 #define CONFIG_EXTRA_ENV_SETTINGS \
 198         DEFAULT_LINUX_BOOT_ENV \
 199         DEFAULT_MMC_TI_ARGS \
 200         "bootpart=0:2\0" \
 201         "bootdir=/boot\0" \
 202         "bootfile=zImage\0" \
 203         "fdtfile=da850-lcdk.dtb\0" \
 204         "boot_fdt=yes\0" \
 205         "boot_fit=0\0" \
 206         "console=ttyS2,115200n8\0"
 207
 208 #ifdef CONFIG_CMD_BDI
 209 #define CONFIG_CLOCKS
 210 #endif
 211
 212 /* SD/MMC */
 213
 214 /* defines for SPL */
 215 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SYS_TEXT_BASE - \
 216                                                 CONFIG_SYS_MALLOC_LEN)
 217 #define CONFIG_SYS_SPL_MALLOC_SIZE      CONFIG_SYS_MALLOC_LEN
 218 #define CONFIG_SPL_STACK        0x8001ff00
 219 #define CONFIG_SPL_MAX_FOOTPRINT        32768
 220 #define CONFIG_SPL_PAD_TO       32768
 221
 222 /* additions for new relocation code, must added to all boards */
 223 #define CONFIG_SYS_SDRAM_BASE           0xc0000000
 224 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
 225                                         GENERATED_GBL_DATA_SIZE)
 226
 227 #include <asm/arch/hardware.h>
 228
 229 #endif /* __CONFIG_H */