include/configs/ls2080ardb.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2017 NXP
   4  * Copyright 2015 Freescale Semiconductor
   5  */
   6
   7 #ifndef __LS2_RDB_H
   8 #define __LS2_RDB_H
   9
  10 #include "ls2080a_common.h"
  11
  12 #ifdef CONFIG_FSL_QSPI
  13 #ifdef CONFIG_TARGET_LS2081ARDB
  14 #define CONFIG_QIXIS_I2C_ACCESS
  15 #endif
  16 #define CONFIG_SYS_I2C_EARLY_INIT
  17 #endif
  18
  19 #define I2C_MUX_CH_VOL_MONITOR          0xa
  20 #define I2C_VOL_MONITOR_ADDR            0x38
  21 #define CONFIG_VOL_MONITOR_IR36021_READ
  22 #define CONFIG_VOL_MONITOR_IR36021_SET
  23
  24 #define CONFIG_VID_FLS_ENV              "ls2080ardb_vdd_mv"
  25 #ifndef CONFIG_SPL_BUILD
  26 #define CONFIG_VID
  27 #endif
  28 /* step the IR regulator in 5mV increments */
  29 #define IR_VDD_STEP_DOWN                5
  30 #define IR_VDD_STEP_UP                  5
  31 /* The lowest and highest voltage allowed for LS2080ARDB */
  32 #define VDD_MV_MIN                      819
  33 #define VDD_MV_MAX                      1212
  34
  35 #ifndef __ASSEMBLY__
  36 unsigned long get_board_sys_clk(void);
  37 #endif
  38
  39 #define CONFIG_SYS_CLK_FREQ             get_board_sys_clk()
  40 #define CONFIG_DDR_CLK_FREQ             133333333
  41 #define COUNTER_FREQUENCY_REAL          (CONFIG_SYS_CLK_FREQ/4)
  42
  43 #define CONFIG_DDR_SPD
  44 #define CONFIG_DDR_ECC
  45 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  46 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  47 #define SPD_EEPROM_ADDRESS1     0x51
  48 #define SPD_EEPROM_ADDRESS2     0x52
  49 #define SPD_EEPROM_ADDRESS3     0x53
  50 #define SPD_EEPROM_ADDRESS4     0x54
  51 #define SPD_EEPROM_ADDRESS5     0x55
  52 #define SPD_EEPROM_ADDRESS6     0x56    /* dummy address */
  53 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
  54 #define CONFIG_SYS_SPD_BUS_NUM  0       /* SPD on I2C bus 0 */
  55 #define CONFIG_DIMM_SLOTS_PER_CTLR              2
  56 #define CONFIG_CHIP_SELECTS_PER_CTRL            4
  57 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR
  58 #define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR       1
  59 #endif
  60
  61 /* SATA */
  62 #define CONFIG_SCSI_AHCI_PLAT
  63
  64 #define CONFIG_SYS_SATA1                        AHCI_BASE_ADDR1
  65 #define CONFIG_SYS_SATA2                        AHCI_BASE_ADDR2
  66
  67 #define CONFIG_SYS_SCSI_MAX_SCSI_ID             1
  68 #define CONFIG_SYS_SCSI_MAX_LUN                 1
  69 #define CONFIG_SYS_SCSI_MAX_DEVICE              (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
  70                                                 CONFIG_SYS_SCSI_MAX_LUN)
  71 #ifdef CONFIG_TFABOOT
  72 #define CONFIG_SYS_MMC_ENV_DEV         0
  73
  74 #define CONFIG_ENV_SIZE                 0x2000
  75 #define CONFIG_ENV_OFFSET               0x500000        /* 5MB */
  76 #define CONFIG_ENV_ADDR                 (CONFIG_SYS_FLASH_BASE + \
  77                                          CONFIG_ENV_OFFSET)
  78 #define CONFIG_ENV_SECT_SIZE            0x40000
  79 #endif
  80
  81 #if !defined(CONFIG_FSL_QSPI) || defined(CONFIG_TFABOOT)
  82
  83 #define CONFIG_SYS_NOR0_CSPR_EXT        (0x0)
  84 #define CONFIG_SYS_NOR_AMASK            IFC_AMASK(128*1024*1024)
  85 #define CONFIG_SYS_NOR_AMASK_EARLY      IFC_AMASK(64*1024*1024)
  86
  87 #define CONFIG_SYS_NOR0_CSPR                                    \
  88         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)             | \
  89         CSPR_PORT_SIZE_16                                       | \
  90         CSPR_MSEL_NOR                                           | \
  91         CSPR_V)
  92 #define CONFIG_SYS_NOR0_CSPR_EARLY                              \
  93         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)       | \
  94         CSPR_PORT_SIZE_16                                       | \
  95         CSPR_MSEL_NOR                                           | \
  96         CSPR_V)
  97 #define CONFIG_SYS_NOR_CSOR     CSOR_NOR_ADM_SHIFT(12)
  98 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
  99                                 FTIM0_NOR_TEADC(0x5) | \
 100                                 FTIM0_NOR_TEAHC(0x5))
 101 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 102                                 FTIM1_NOR_TRAD_NOR(0x1a) |\
 103                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 104 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 105                                 FTIM2_NOR_TCH(0x4) | \
 106                                 FTIM2_NOR_TWPH(0x0E) | \
 107                                 FTIM2_NOR_TWP(0x1c))
 108 #define CONFIG_SYS_NOR_FTIM3    0x04000000
 109 #define CONFIG_SYS_IFC_CCR      0x01000000
 110
 111 #ifdef CONFIG_MTD_NOR_FLASH
 112 #define CONFIG_SYS_FLASH_QUIET_TEST
 113 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 114
 115 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 116 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 117 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 118 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 119
 120 #define CONFIG_SYS_FLASH_EMPTY_INFO
 121 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_FLASH_BASE,\
 122                                          CONFIG_SYS_FLASH_BASE + 0x40000000}
 123 #endif
 124
 125 #define CONFIG_NAND_FSL_IFC
 126 #define CONFIG_SYS_NAND_MAX_ECCPOS      256
 127 #define CONFIG_SYS_NAND_MAX_OOBFREE     2
 128
 129 #define CONFIG_SYS_NAND_CSPR_EXT        (0x0)
 130 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 131                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 132                                 | CSPR_MSEL_NAND        /* MSEL = NAND */ \
 133                                 | CSPR_V)
 134 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64 * 1024)
 135
 136 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 137                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 138                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 139                                 | CSOR_NAND_RAL_3       /* RAL = 3Byes */ \
 140                                 | CSOR_NAND_PGS_4K      /* Page Size = 4K */ \
 141                                 | CSOR_NAND_SPRZ_224    /* Spare size = 224 */ \
 142                                 | CSOR_NAND_PB(128))    /* Pages Per Block 128*/
 143
 144 #define CONFIG_SYS_NAND_ONFI_DETECTION
 145
 146 /* ONFI NAND Flash mode0 Timing Params */
 147 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x0e) | \
 148                                         FTIM0_NAND_TWP(0x30)   | \
 149                                         FTIM0_NAND_TWCHT(0x0e) | \
 150                                         FTIM0_NAND_TWH(0x14))
 151 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x64) | \
 152                                         FTIM1_NAND_TWBE(0xab)  | \
 153                                         FTIM1_NAND_TRR(0x1c)   | \
 154                                         FTIM1_NAND_TRP(0x30))
 155 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x1e) | \
 156                                         FTIM2_NAND_TREH(0x14) | \
 157                                         FTIM2_NAND_TWHRE(0x3c))
 158 #define CONFIG_SYS_NAND_FTIM3           0x0
 159
 160 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 161 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 162 #define CONFIG_MTD_NAND_VERIFY_WRITE
 163
 164 #define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)
 165 #define CONFIG_FSL_QIXIS        /* use common QIXIS code */
 166 #define QIXIS_LBMAP_SWITCH              0x06
 167 #define QIXIS_LBMAP_MASK                0x0f
 168 #define QIXIS_LBMAP_SHIFT               0
 169 #define QIXIS_LBMAP_DFLTBANK            0x00
 170 #define QIXIS_LBMAP_ALTBANK             0x04
 171 #define QIXIS_LBMAP_NAND                0x09
 172 #define QIXIS_RST_CTL_RESET             0x31
 173 #define QIXIS_RST_CTL_RESET_EN          0x30
 174 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 175 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 176 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 177 #define QIXIS_RCW_SRC_NAND              0x119
 178 #define QIXIS_RST_FORCE_MEM             0x01
 179
 180 #define CONFIG_SYS_CSPR3_EXT    (0x0)
 181 #define CONFIG_SYS_CSPR3        (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
 182                                 | CSPR_PORT_SIZE_8 \
 183                                 | CSPR_MSEL_GPCM \
 184                                 | CSPR_V)
 185 #define CONFIG_SYS_CSPR3_FINAL  (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
 186                                 | CSPR_PORT_SIZE_8 \
 187                                 | CSPR_MSEL_GPCM \
 188                                 | CSPR_V)
 189
 190 #define CONFIG_SYS_AMASK3       IFC_AMASK(64*1024)
 191 #define CONFIG_SYS_CSOR3        CSOR_GPCM_ADM_SHIFT(12)
 192 /* QIXIS Timing parameters for IFC CS3 */
 193 #define CONFIG_SYS_CS3_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 194                                         FTIM0_GPCM_TEADC(0x0e) | \
 195                                         FTIM0_GPCM_TEAHC(0x0e))
 196 #define CONFIG_SYS_CS3_FTIM1            (FTIM1_GPCM_TACO(0xff) | \
 197                                         FTIM1_GPCM_TRAD(0x3f))
 198 #define CONFIG_SYS_CS3_FTIM2            (FTIM2_GPCM_TCS(0xf) | \
 199                                         FTIM2_GPCM_TCH(0xf) | \
 200                                         FTIM2_GPCM_TWP(0x3E))
 201 #define CONFIG_SYS_CS3_FTIM3            0x0
 202
 203 #if defined(CONFIG_SPL) && defined(CONFIG_NAND)
 204 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 205 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NOR0_CSPR_EARLY
 206 #define CONFIG_SYS_CSPR2_FINAL          CONFIG_SYS_NOR0_CSPR
 207 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NOR_AMASK
 208 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NOR_CSOR
 209 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NOR_FTIM0
 210 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NOR_FTIM1
 211 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NOR_FTIM2
 212 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NOR_FTIM3
 213 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 214 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 215 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 216 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 217 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 218 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 219 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 220 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 221
 222 #ifndef CONFIG_TFABOOT
 223 #define CONFIG_ENV_OFFSET               (2048 * 1024)
 224 #define CONFIG_ENV_SECT_SIZE            0x20000
 225 #define CONFIG_ENV_SIZE                 0x2000
 226 #endif
 227 #define CONFIG_SPL_PAD_TO               0x80000
 228 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (1024 * 1024)
 229 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (512 * 1024)
 230 #else
 231 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 232 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR_EARLY
 233 #define CONFIG_SYS_CSPR0_FINAL          CONFIG_SYS_NOR0_CSPR
 234 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 235 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 236 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 237 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 238 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 239 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 240 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NAND_CSPR_EXT
 241 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NAND_CSPR
 242 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NAND_AMASK
 243 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NAND_CSOR
 244 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NAND_FTIM0
 245 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NAND_FTIM1
 246 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NAND_FTIM2
 247 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NAND_FTIM3
 248
 249 #ifndef CONFIG_TFABOOT
 250 #define CONFIG_ENV_ADDR                 (CONFIG_SYS_FLASH_BASE + 0x300000)
 251 #define CONFIG_ENV_SECT_SIZE            0x20000
 252 #define CONFIG_ENV_SIZE                 0x2000
 253 #endif
 254 #endif
 255
 256 /* Debug Server firmware */
 257 #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
 258 #define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL
 259 #endif
 260 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
 261
 262 #ifdef CONFIG_TARGET_LS2081ARDB
 263 #define CONFIG_FSL_QIXIS        /* use common QIXIS code */
 264 #define QIXIS_QMAP_MASK                 0x07
 265 #define QIXIS_QMAP_SHIFT                5
 266 #define QIXIS_LBMAP_DFLTBANK            0x00
 267 #define QIXIS_LBMAP_QSPI                0x00
 268 #define QIXIS_RCW_SRC_QSPI              0x62
 269 #define QIXIS_LBMAP_ALTBANK             0x20
 270 #define QIXIS_RST_CTL_RESET             0x31
 271 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 272 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 273 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 274 #define QIXIS_LBMAP_MASK                0x0f
 275 #define QIXIS_RST_CTL_RESET_EN          0x30
 276 #endif
 277
 278 /*
 279  * I2C
 280  */
 281 #ifdef CONFIG_TARGET_LS2081ARDB
 282 #define CONFIG_SYS_I2C_FPGA_ADDR        0x66
 283 #endif
 284 #define I2C_MUX_PCA_ADDR                0x75
 285 #define I2C_MUX_PCA_ADDR_PRI            0x75 /* Primary Mux*/
 286
 287 /* I2C bus multiplexer */
 288 #define I2C_MUX_CH_DEFAULT      0x8
 289
 290 /* SPI */
 291 #if defined(CONFIG_FSL_QSPI) || defined(CONFIG_FSL_DSPI)
 292 #ifdef CONFIG_FSL_DSPI
 293 #define CONFIG_SPI_FLASH_STMICRO
 294 #endif
 295 #define FSL_QSPI_FLASH_SIZE             SZ_64M  /* 64MB */
 296 #define FSL_QSPI_FLASH_NUM              2
 297 #endif
 298
 299 /*
 300  * RTC configuration
 301  */
 302 #define RTC
 303 #ifdef CONFIG_TARGET_LS2081ARDB
 304 #define CONFIG_RTC_PCF8563              1
 305 #define CONFIG_SYS_I2C_RTC_ADDR         0x51
 306 #else
 307 #define CONFIG_RTC_DS3231               1
 308 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 309 #endif
 310
 311 /* EEPROM */
 312 #define CONFIG_ID_EEPROM
 313 #define CONFIG_SYS_I2C_EEPROM_NXID
 314 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 315 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x57
 316 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
 317 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 318 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
 319
 320 #define CONFIG_FSL_MEMAC
 321
 322 #ifdef CONFIG_PCI
 323 #define CONFIG_PCI_SCAN_SHOW
 324 #endif
 325
 326 /*  MMC  */
 327 #ifdef CONFIG_MMC
 328 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 329 #endif
 330
 331 #define BOOT_TARGET_DEVICES(func) \
 332         func(USB, usb, 0) \
 333         func(MMC, mmc, 0) \
 334         func(SCSI, scsi, 0) \
 335         func(DHCP, dhcp, na)
 336 #include <config_distro_bootcmd.h>
 337
 338 #ifdef CONFIG_TFABOOT
 339 #define QSPI_MC_INIT_CMD                        \
 340         "env exists secureboot && "             \
 341         "esbc_validate 0x20700000 && "          \
 342         "esbc_validate 0x20740000;"             \
 343         "fsl_mc start mc 0x20a00000 0x20e00000 \0"
 344 #define SD_MC_INIT_CMD                          \
 345         "mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
 346         "mmc read 0x80100000 0x7000 0x800;"     \
 347         "env exists secureboot && "             \
 348         "mmc read 0x80700000 0x3800 0x10 && "   \
 349         "mmc read 0x80740000 0x3A00 0x10 && "   \
 350         "esbc_validate 0x80700000 && "          \
 351         "esbc_validate 0x80740000 ;"            \
 352         "fsl_mc start mc 0x80000000 0x80100000\0"
 353 #define IFC_MC_INIT_CMD                         \
 354         "env exists secureboot && "     \
 355         "esbc_validate 0x580700000 && "         \
 356         "esbc_validate 0x580740000; "           \
 357         "fsl_mc start mc 0x580a00000 0x580e00000 \0"
 358 #else
 359 #ifdef CONFIG_QSPI_BOOT
 360 #define MC_INIT_CMD                             \
 361         "mcinitcmd=env exists secureboot && "   \
 362         "esbc_validate 0x20700000 && "          \
 363         "esbc_validate 0x20740000;"             \
 364         "fsl_mc start mc 0x20a00000 0x20e00000 \0"
 365 #elif defined(CONFIG_SD_BOOT)
 366 #define MC_INIT_CMD                             \
 367         "mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
 368         "mmc read 0x80100000 0x7000 0x800;"     \
 369         "env exists secureboot && "             \
 370         "mmc read 0x80700000 0x3800 0x10 && "   \
 371         "mmc read 0x80740000 0x3A00 0x10 && "   \
 372         "esbc_validate 0x80700000 && "          \
 373         "esbc_validate 0x80740000 ;"            \
 374         "fsl_mc start mc 0x80000000 0x80100000\0" \
 375         "mcmemsize=0x70000000\0"
 376 #else
 377 #define MC_INIT_CMD                             \
 378         "mcinitcmd=env exists secureboot && "   \
 379         "esbc_validate 0x580700000 && "         \
 380         "esbc_validate 0x580740000; "           \
 381         "fsl_mc start mc 0x580a00000 0x580e00000 \0"
 382 #endif
 383 #endif
 384
 385 /* Initial environment variables */
 386 #undef CONFIG_EXTRA_ENV_SETTINGS
 387 #ifdef CONFIG_TFABOOT
 388 #define CONFIG_EXTRA_ENV_SETTINGS               \
 389         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 390         "ramdisk_addr=0x800000\0"               \
 391         "ramdisk_size=0x2000000\0"              \
 392         "fdt_high=0xa0000000\0"                 \
 393         "initrd_high=0xffffffffffffffff\0"      \
 394         "fdt_addr=0x64f00000\0"                 \
 395         "kernel_addr=0x581000000\0"             \
 396         "kernel_start=0x1000000\0"              \
 397         "kernelheader_start=0x800000\0"         \
 398         "scriptaddr=0x80000000\0"               \
 399         "scripthdraddr=0x80080000\0"            \
 400         "fdtheader_addr_r=0x80100000\0"         \
 401         "kernelheader_addr_r=0x80200000\0"      \
 402         "kernelheader_addr=0x580800000\0"       \
 403         "kernel_addr_r=0x81000000\0"            \
 404         "kernelheader_size=0x40000\0"           \
 405         "fdt_addr_r=0x90000000\0"               \
 406         "load_addr=0xa0000000\0"                \
 407         "kernel_size=0x2800000\0"               \
 408         "kernel_addr_sd=0x8000\0"               \
 409         "kernel_size_sd=0x14000\0"              \
 410         "console=ttyAMA0,38400n8\0"             \
 411         "mcmemsize=0x70000000\0"                \
 412         "sd_bootcmd=echo Trying load from SD ..;" \
 413         "mmcinfo; mmc read $load_addr "         \
 414         "$kernel_addr_sd $kernel_size_sd && "   \
 415         "bootm $load_addr#$board\0"             \
 416         QSPI_MC_INIT_CMD                                \
 417         BOOTENV                                 \
 418         "boot_scripts=ls2088ardb_boot.scr\0"    \
 419         "boot_script_hdr=hdr_ls2088ardb_bs.out\0"       \
 420         "scan_dev_for_boot_part="               \
 421                 "part list ${devtype} ${devnum} devplist; "     \
 422                 "env exists devplist || setenv devplist 1; "    \
 423                 "for distro_bootpart in ${devplist}; do "       \
 424                         "if fstype ${devtype} "                 \
 425                                 "${devnum}:${distro_bootpart} " \
 426                                 "bootfstype; then "             \
 427                                 "run scan_dev_for_boot; "       \
 428                         "fi; "                                  \
 429                 "done\0"                                        \
 430         "boot_a_script="                                        \
 431                 "load ${devtype} ${devnum}:${distro_bootpart} " \
 432                         "${scriptaddr} ${prefix}${script}; "    \
 433                 "env exists secureboot && load ${devtype} "     \
 434                         "${devnum}:${distro_bootpart} "         \
 435                         "${scripthdraddr} ${prefix}${boot_script_hdr} " \
 436                         "&& esbc_validate ${scripthdraddr};"    \
 437                 "source ${scriptaddr}\0"                        \
 438         "qspi_bootcmd=echo Trying load from qspi..;"            \
 439                 "sf probe && sf read $load_addr "               \
 440                 "$kernel_start $kernel_size ; env exists secureboot &&" \
 441                 "sf read $kernelheader_addr_r $kernelheader_start "     \
 442                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 443                 " bootm $load_addr#$board\0"                    \
 444         "nor_bootcmd=echo Trying load from nor..;"              \
 445                 "cp.b $kernel_addr $load_addr "                 \
 446                 "$kernel_size ; env exists secureboot && "      \
 447                 "cp.b $kernelheader_addr $kernelheader_addr_r " \
 448                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 449                 "bootm $load_addr#$board\0"
 450 #else
 451 #define CONFIG_EXTRA_ENV_SETTINGS               \
 452         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 453         "ramdisk_addr=0x800000\0"               \
 454         "ramdisk_size=0x2000000\0"              \
 455         "fdt_high=0xa0000000\0"                 \
 456         "initrd_high=0xffffffffffffffff\0"      \
 457         "fdt_addr=0x64f00000\0"                 \
 458         "kernel_addr=0x581000000\0"             \
 459         "kernel_start=0x1000000\0"              \
 460         "kernelheader_start=0x800000\0"         \
 461         "scriptaddr=0x80000000\0"               \
 462         "scripthdraddr=0x80080000\0"            \
 463         "fdtheader_addr_r=0x80100000\0"         \
 464         "kernelheader_addr_r=0x80200000\0"      \
 465         "kernelheader_addr=0x580800000\0"       \
 466         "kernel_addr_r=0x81000000\0"            \
 467         "kernelheader_size=0x40000\0"           \
 468         "fdt_addr_r=0x90000000\0"               \
 469         "load_addr=0xa0000000\0"                \
 470         "kernel_size=0x2800000\0"               \
 471         "kernel_addr_sd=0x8000\0"               \
 472         "kernel_size_sd=0x14000\0"              \
 473         "console=ttyAMA0,38400n8\0"             \
 474         "mcmemsize=0x70000000\0"                \
 475         "sd_bootcmd=echo Trying load from SD ..;" \
 476         "mmcinfo; mmc read $load_addr "         \
 477         "$kernel_addr_sd $kernel_size_sd && "   \
 478         "bootm $load_addr#$board\0"             \
 479         MC_INIT_CMD                             \
 480         BOOTENV                                 \
 481         "boot_scripts=ls2088ardb_boot.scr\0"    \
 482         "boot_script_hdr=hdr_ls2088ardb_bs.out\0"       \
 483         "scan_dev_for_boot_part="               \
 484                 "part list ${devtype} ${devnum} devplist; "     \
 485                 "env exists devplist || setenv devplist 1; "    \
 486                 "for distro_bootpart in ${devplist}; do "       \
 487                         "if fstype ${devtype} "                 \
 488                                 "${devnum}:${distro_bootpart} " \
 489                                 "bootfstype; then "             \
 490                                 "run scan_dev_for_boot; "       \
 491                         "fi; "                                  \
 492                 "done\0"                                        \
 493         "boot_a_script="                                        \
 494                 "load ${devtype} ${devnum}:${distro_bootpart} " \
 495                         "${scriptaddr} ${prefix}${script}; "    \
 496                 "env exists secureboot && load ${devtype} "     \
 497                         "${devnum}:${distro_bootpart} "         \
 498                         "${scripthdraddr} ${prefix}${boot_script_hdr}; " \
 499                         "env exists secureboot "        \
 500                         "&& esbc_validate ${scripthdraddr};"    \
 501                 "source ${scriptaddr}\0"                        \
 502         "qspi_bootcmd=echo Trying load from qspi..;"            \
 503                 "sf probe && sf read $load_addr "               \
 504                 "$kernel_start $kernel_size ; env exists secureboot &&" \
 505                 "sf read $kernelheader_addr_r $kernelheader_start "     \
 506                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 507                 " bootm $load_addr#$board\0"                    \
 508         "nor_bootcmd=echo Trying load from nor..;"              \
 509                 "cp.b $kernel_addr $load_addr "                 \
 510                 "$kernel_size ; env exists secureboot && "      \
 511                 "cp.b $kernelheader_addr $kernelheader_addr_r " \
 512                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 513                 "bootm $load_addr#$board\0"
 514 #endif
 515
 516 #ifdef CONFIG_TFABOOT
 517 #define QSPI_NOR_BOOTCOMMAND                                            \
 518                         "env exists mcinitcmd && env exists secureboot "\
 519                         "&& esbc_validate 0x20780000; "                 \
 520                         "env exists mcinitcmd && "                      \
 521                         "fsl_mc lazyapply dpl 0x20d00000; "             \
 522                         "run distro_bootcmd;run qspi_bootcmd; "         \
 523                         "env exists secureboot && esbc_halt;"
 524
 525 /* Try to boot an on-SD kernel first, then do normal distro boot */
 526 #define SD_BOOTCOMMAND                                          \
 527                         "env exists mcinitcmd && env exists secureboot "\
 528                         "&& mmcinfo && mmc read $load_addr 0x3c00 0x800 " \
 529                         "&& esbc_validate $load_addr; "                 \
 530                         "env exists mcinitcmd && run mcinitcmd "        \
 531                         "&& mmc read 0x88000000 0x6800 0x800 "          \
 532                         "&& fsl_mc lazyapply dpl 0x88000000; "          \
 533                         "run distro_bootcmd;run sd_bootcmd; "           \
 534                         "env exists secureboot && esbc_halt;"
 535
 536 /* Try to boot an on-NOR kernel first, then do normal distro boot */
 537 #define IFC_NOR_BOOTCOMMAND                                             \
 538                         "env exists mcinitcmd && env exists secureboot "\
 539                         "&& esbc_validate 0x580780000; env exists mcinitcmd "\
 540                         "&& fsl_mc lazyapply dpl 0x580d00000;"          \
 541                         "run distro_bootcmd;run nor_bootcmd; "          \
 542                         "env exists secureboot && esbc_halt;"
 543 #else
 544 #undef CONFIG_BOOTCOMMAND
 545 #ifdef CONFIG_QSPI_BOOT
 546 /* Try to boot an on-QSPI kernel first, then do normal distro boot */
 547 #define CONFIG_BOOTCOMMAND                                              \
 548                         "env exists mcinitcmd && env exists secureboot "\
 549                         "&& esbc_validate 0x20780000; "                 \
 550                         "env exists mcinitcmd && "                      \
 551                         "fsl_mc lazyapply dpl 0x20d00000; "             \
 552                         "run distro_bootcmd;run qspi_bootcmd; "         \
 553                         "env exists secureboot && esbc_halt;"
 554 #elif defined(CONFIG_SD_BOOT)
 555 /* Try to boot an on-SD kernel first, then do normal distro boot */
 556 #define CONFIG_BOOTCOMMAND                                              \
 557                         "env exists mcinitcmd && env exists secureboot "\
 558                         "&& mmcinfo && mmc read $load_addr 0x3c00 0x800 " \
 559                         "&& esbc_validate $load_addr; "                 \
 560                         "env exists mcinitcmd && run mcinitcmd "        \
 561                         "&& mmc read 0x88000000 0x6800 0x800 "          \
 562                         "&& fsl_mc lazyapply dpl 0x88000000; "          \
 563                         "run distro_bootcmd;run sd_bootcmd; "           \
 564                         "env exists secureboot && esbc_halt;"
 565 #else
 566 /* Try to boot an on-NOR kernel first, then do normal distro boot */
 567 #define CONFIG_BOOTCOMMAND                                              \
 568                         "env exists mcinitcmd && env exists secureboot "\
 569                         "&& esbc_validate 0x580780000; env exists mcinitcmd "\
 570                         "&& fsl_mc lazyapply dpl 0x580d00000;"          \
 571                         "run distro_bootcmd;run nor_bootcmd; "          \
 572                         "env exists secureboot && esbc_halt;"
 573 #endif
 574 #endif
 575
 576 /* MAC/PHY configuration */
 577 #ifdef CONFIG_FSL_MC_ENET
 578 #define CONFIG_PHY_CORTINA
 579 #define CONFIG_SYS_CORTINA_FW_IN_NOR
 580 #ifdef CONFIG_QSPI_BOOT
 581 #define CONFIG_CORTINA_FW_ADDR          0x20980000
 582 #else
 583 #define CONFIG_CORTINA_FW_ADDR          0x580980000
 584 #endif
 585 #define CONFIG_CORTINA_FW_LENGTH        0x40000
 586
 587 #define CORTINA_PHY_ADDR1       0x10
 588 #define CORTINA_PHY_ADDR2       0x11
 589 #define CORTINA_PHY_ADDR3       0x12
 590 #define CORTINA_PHY_ADDR4       0x13
 591 #define AQ_PHY_ADDR1            0x00
 592 #define AQ_PHY_ADDR2            0x01
 593 #define AQ_PHY_ADDR3            0x02
 594 #define AQ_PHY_ADDR4            0x03
 595 #define AQR405_IRQ_MASK         0x36
 596
 597 #define CONFIG_ETHPRIME         "DPMAC1@xgmii"
 598 #endif
 599
 600 #include <asm/fsl_secure_boot.h>
 601
 602 #endif /* __LS2_RDB_H */