include/configs/ls1046a_common.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2016 Freescale Semiconductor
   4  */
   5
   6 #ifndef __LS1046A_COMMON_H
   7 #define __LS1046A_COMMON_H
   8
   9 /* SPL build */
  10 #ifdef CONFIG_SPL_BUILD
  11 #define SPL_NO_QBMAN
  12 #define SPL_NO_FMAN
  13 #define SPL_NO_ENV
  14 #define SPL_NO_MISC
  15 #define SPL_NO_QSPI
  16 #define SPL_NO_USB
  17 #define SPL_NO_SATA
  18 #endif
  19 #if defined(CONFIG_SPL_BUILD) && \
  20         (defined(CONFIG_NAND_BOOT) || defined(CONFIG_QSPI_BOOT))
  21 #define SPL_NO_MMC
  22 #endif
  23 #if defined(CONFIG_SPL_BUILD)           && \
  24         !defined(CONFIG_SPL_FSL_LS_PPA)
  25 #define SPL_NO_IFC
  26 #endif
  27
  28 #define CONFIG_REMAKE_ELF
  29 #define CONFIG_GICV2
  30
  31 #include <asm/arch/config.h>
  32 #include <asm/arch/stream_id_lsch2.h>
  33
  34 /* Link Definitions */
  35 #ifdef CONFIG_TFABOOT
  36 #define CONFIG_SYS_INIT_SP_ADDR         CONFIG_SYS_TEXT_BASE
  37 #else
  38 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
  39 #endif
  40
  41 #define CONFIG_SKIP_LOWLEVEL_INIT
  42
  43 #define CONFIG_VERY_BIG_RAM
  44 #define CONFIG_SYS_DDR_SDRAM_BASE       0x80000000
  45 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  46 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  47 #define CONFIG_SYS_DDR_BLOCK2_BASE      0x880000000ULL
  48
  49 #define CPU_RELEASE_ADDR               secondary_boot_func
  50
  51 /* Generic Timer Definitions */
  52 #define COUNTER_FREQUENCY               25000000        /* 25MHz */
  53
  54 /* Size of malloc() pool */
  55 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 1024 * 1024)
  56
  57 /* Serial Port */
  58 #define CONFIG_SYS_NS16550_SERIAL
  59 #define CONFIG_SYS_NS16550_REG_SIZE     1
  60 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
  61
  62 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
  63
  64 /* SD boot SPL */
  65 #ifdef CONFIG_SD_BOOT
  66 #define CONFIG_SPL_TEXT_BASE            0x10000000
  67 #define CONFIG_SPL_MAX_SIZE             0x1f000         /* 124 KiB */
  68 #define CONFIG_SPL_STACK                0x10020000
  69 #define CONFIG_SPL_PAD_TO               0x21000         /* 132 KiB */
  70 #define CONFIG_SPL_BSS_START_ADDR       0x8f000000
  71 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
  72 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SPL_BSS_START_ADDR + \
  73                                         CONFIG_SPL_BSS_MAX_SIZE)
  74 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
  75
  76 #ifdef CONFIG_SECURE_BOOT
  77 #define CONFIG_U_BOOT_HDR_SIZE                          (16 << 10)
  78 /*
  79  * HDR would be appended at end of image and copied to DDR along
  80  * with U-Boot image. Here u-boot max. size is 512K. So if binary
  81  * size increases then increase this size in case of secure boot as
  82  * it uses raw u-boot image instead of fit image.
  83  */
  84 #define CONFIG_SYS_MONITOR_LEN          (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
  85 #else
  86 #define CONFIG_SYS_MONITOR_LEN          0x100000
  87 #endif /* ifdef CONFIG_SECURE_BOOT */
  88 #endif
  89
  90 #if defined(CONFIG_QSPI_BOOT) && defined(CONFIG_SPL)
  91 #define CONFIG_SPL_TARGET               "spl/u-boot-spl.pbl"
  92 #define CONFIG_SPL_TEXT_BASE            0x10000000
  93 #define CONFIG_SPL_MAX_SIZE             0x1f000
  94 #define CONFIG_SPL_STACK                0x10020000
  95 #define CONFIG_SPL_PAD_TO               0x20000
  96 #define CONFIG_SPL_BSS_START_ADDR       0x8f000000
  97 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
  98 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SPL_BSS_START_ADDR + \
  99                                         CONFIG_SPL_BSS_MAX_SIZE)
 100 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
 101 #define CONFIG_SYS_MONITOR_LEN          0x100000
 102 #define CONFIG_SYS_UBOOT_START          CONFIG_SYS_TEXT_BASE
 103 #endif
 104
 105 /* NAND SPL */
 106 #ifdef CONFIG_NAND_BOOT
 107 #define CONFIG_SPL_PBL_PAD
 108 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 109 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 110 #define CONFIG_SPL_ENV_SUPPORT
 111 #define CONFIG_SPL_WATCHDOG_SUPPORT
 112 #define CONFIG_SPL_I2C_SUPPORT
 113 #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
 114
 115 #define CONFIG_SPL_NAND_SUPPORT
 116 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
 117 #define CONFIG_SPL_TEXT_BASE            0x10000000
 118 #define CONFIG_SPL_MAX_SIZE             0x17000         /* 90 KiB */
 119 #define CONFIG_SPL_STACK                0x1001f000
 120 #define CONFIG_SYS_NAND_U_BOOT_DST      CONFIG_SYS_TEXT_BASE
 121 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
 122
 123 #define CONFIG_SPL_BSS_START_ADDR       0x8f000000
 124 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
 125 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SPL_BSS_START_ADDR + \
 126                                         CONFIG_SPL_BSS_MAX_SIZE)
 127 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
 128 #define CONFIG_SYS_MONITOR_LEN          0xa0000
 129 #endif
 130
 131 /* I2C */
 132 #define CONFIG_SYS_I2C
 133
 134 /* PCIe */
 135 #define CONFIG_PCIE1            /* PCIE controller 1 */
 136 #define CONFIG_PCIE2            /* PCIE controller 2 */
 137 #define CONFIG_PCIE3            /* PCIE controller 3 */
 138
 139 #ifdef CONFIG_PCI
 140 #define CONFIG_PCI_SCAN_SHOW
 141 #endif
 142
 143 /* SATA */
 144 #ifndef SPL_NO_SATA
 145 #define CONFIG_SCSI_AHCI_PLAT
 146
 147 #define CONFIG_SYS_SATA                         AHCI_BASE_ADDR
 148
 149 #define CONFIG_SYS_SCSI_MAX_SCSI_ID             1
 150 #define CONFIG_SYS_SCSI_MAX_LUN                 1
 151 #define CONFIG_SYS_SCSI_MAX_DEVICE              (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
 152                                                 CONFIG_SYS_SCSI_MAX_LUN)
 153 #endif
 154
 155 /* Command line configuration */
 156
 157 /* MMC */
 158 #ifndef SPL_NO_MMC
 159 #ifdef CONFIG_MMC
 160 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 161 #endif
 162 #endif
 163
 164 /* FMan ucode */
 165 #ifndef SPL_NO_FMAN
 166 #define CONFIG_SYS_DPAA_FMAN
 167 #ifdef CONFIG_SYS_DPAA_FMAN
 168 #define CONFIG_SYS_FM_MURAM_SIZE        0x60000
 169 #endif
 170
 171 #ifdef CONFIG_TFABOOT
 172 #define CONFIG_SYS_FMAN_FW_ADDR         0x900000
 173 #define CONFIG_ENV_SPI_BUS              0
 174 #define CONFIG_ENV_SPI_CS               0
 175 #define CONFIG_ENV_SPI_MAX_HZ           1000000
 176 #define CONFIG_ENV_SPI_MODE             0x03
 177 #else
 178 #ifdef CONFIG_SD_BOOT
 179 /*
 180  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 181  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 182  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 18432(0x4800).
 183  */
 184 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
 185 #define CONFIG_SYS_FMAN_FW_ADDR         (512 * 0x4800)
 186 #elif defined(CONFIG_QSPI_BOOT)
 187 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
 188 #define CONFIG_SYS_FMAN_FW_ADDR         0x40900000
 189 #define CONFIG_ENV_SPI_BUS              0
 190 #define CONFIG_ENV_SPI_CS               0
 191 #define CONFIG_ENV_SPI_MAX_HZ           1000000
 192 #define CONFIG_ENV_SPI_MODE             0x03
 193 #elif defined(CONFIG_NAND_BOOT)
 194 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
 195 #define CONFIG_SYS_FMAN_FW_ADDR         (36 * CONFIG_SYS_NAND_BLOCK_SIZE)
 196 #else
 197 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 198 #define CONFIG_SYS_FMAN_FW_ADDR         0x60900000
 199 #endif
 200 #endif
 201 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 202 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 203 #endif
 204
 205 /* Miscellaneous configurable options */
 206 #define CONFIG_SYS_LOAD_ADDR    (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
 207
 208 #define CONFIG_HWCONFIG
 209 #define HWCONFIG_BUFFER_SIZE            128
 210
 211 #ifndef CONFIG_SPL_BUILD
 212 #define BOOT_TARGET_DEVICES(func) \
 213         func(SCSI, scsi, 0) \
 214         func(MMC, mmc, 0) \
 215         func(USB, usb, 0)
 216 #include <config_distro_bootcmd.h>
 217 #endif
 218
 219 #ifndef SPL_NO_MISC
 220 /* Initial environment variables */
 221 #define CONFIG_EXTRA_ENV_SETTINGS               \
 222         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 223         "ramdisk_addr=0x800000\0"               \
 224         "ramdisk_size=0x2000000\0"              \
 225         "fdt_high=0xffffffffffffffff\0"         \
 226         "initrd_high=0xffffffffffffffff\0"      \
 227         "fdt_addr=0x64f00000\0"                 \
 228         "kernel_addr=0x65000000\0"              \
 229         "scriptaddr=0x80000000\0"               \
 230         "scripthdraddr=0x80080000\0"            \
 231         "fdtheader_addr_r=0x80100000\0"         \
 232         "kernelheader_addr_r=0x80200000\0"      \
 233         "load_addr=0xa0000000\0"            \
 234         "kernel_addr_r=0x81000000\0"            \
 235         "fdt_addr_r=0x90000000\0"               \
 236         "ramdisk_addr_r=0xa0000000\0"           \
 237         "kernel_start=0x1000000\0"              \
 238         "kernelheader_start=0x800000\0"         \
 239         "kernel_load=0xa0000000\0"              \
 240         "kernel_size=0x2800000\0"               \
 241         "kernelheader_size=0x40000\0"           \
 242         "kernel_addr_sd=0x8000\0"               \
 243         "kernel_size_sd=0x14000\0"              \
 244         "kernelhdr_addr_sd=0x4000\0"            \
 245         "kernelhdr_size_sd=0x10\0"              \
 246         "console=ttyS0,115200\0"                \
 247          CONFIG_MTDPARTS_DEFAULT "\0"           \
 248         BOOTENV                                 \
 249         "boot_scripts=ls1046ardb_boot.scr\0"    \
 250         "boot_script_hdr=hdr_ls1046ardb_bs.out\0"       \
 251         "scan_dev_for_boot_part="               \
 252                 "part list ${devtype} ${devnum} devplist; "   \
 253                 "env exists devplist || setenv devplist 1; "  \
 254                 "for distro_bootpart in ${devplist}; do "     \
 255                   "if fstype ${devtype} "                  \
 256                         "${devnum}:${distro_bootpart} "      \
 257                         "bootfstype; then "                  \
 258                         "run scan_dev_for_boot; "            \
 259                   "fi; "                                   \
 260                 "done\0"                                   \
 261         "scan_dev_for_boot="                              \
 262                 "echo Scanning ${devtype} "               \
 263                                 "${devnum}:${distro_bootpart}...; "  \
 264                 "for prefix in ${boot_prefixes}; do "     \
 265                         "run scan_dev_for_scripts; "      \
 266                 "done;"                                   \
 267                 "\0"                                      \
 268         "boot_a_script="                                  \
 269                 "load ${devtype} ${devnum}:${distro_bootpart} "  \
 270                         "${scriptaddr} ${prefix}${script}; "    \
 271                 "env exists secureboot && load ${devtype} "     \
 272                         "${devnum}:${distro_bootpart} "         \
 273                         "${scripthdraddr} ${prefix}${boot_script_hdr} " \
 274                         "&& esbc_validate ${scripthdraddr};"    \
 275                 "source ${scriptaddr}\0"          \
 276         "qspi_bootcmd=echo Trying load from qspi..;"      \
 277                 "sf probe && sf read $load_addr "         \
 278                 "$kernel_start $kernel_size; env exists secureboot "    \
 279                 "&& sf read $kernelheader_addr_r $kernelheader_start "  \
 280                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 281                 "bootm $load_addr#$board\0"             \
 282         "sd_bootcmd=echo Trying load from SD ..;"       \
 283                 "mmcinfo; mmc read $load_addr "         \
 284                 "$kernel_addr_sd $kernel_size_sd && "   \
 285                 "env exists secureboot && mmc read $kernelheader_addr_r "               \
 286                 "$kernelhdr_addr_sd $kernelhdr_size_sd "                \
 287                 " && esbc_validate ${kernelheader_addr_r};"     \
 288                 "bootm $load_addr#$board\0"
 289
 290 #endif
 291
 292 /* Monitor Command Prompt */
 293 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 294
 295 #define CONFIG_SYS_MAXARGS              64      /* max command args */
 296
 297 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 298
 299 #include <asm/arch/soc.h>
 300
 301 #endif /* __LS1046A_COMMON_H */