include/configs/ls1012a_common.h

   1 /*
   2  * Copyright 2016 Freescale Semiconductor
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #ifndef __LS1012A_COMMON_H
   8 #define __LS1012A_COMMON_H
   9
  10 #define CONFIG_FSL_LAYERSCAPE
  11 #define CONFIG_GICV2
  12
  13 #include <asm/arch/config.h>
  14 #include <asm/arch/stream_id_lsch2.h>
  15
  16 #define CONFIG_DISPLAY_BOARDINFO_LATE
  17
  18 #define CONFIG_SYS_CLK_FREQ             125000000
  19
  20 #define CONFIG_SKIP_LOWLEVEL_INIT
  21
  22 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
  23 #define CONFIG_SYS_LOAD_ADDR    (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
  24
  25 #define CONFIG_SYS_DDR_SDRAM_BASE       0x80000000
  26 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  27 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  28 #define CONFIG_SYS_DDR_BLOCK2_BASE     0x880000000ULL
  29
  30 /* Generic Timer Definitions */
  31 #define COUNTER_FREQUENCY               25000000        /* 25MHz */
  32
  33 /* CSU */
  34 #define CONFIG_LAYERSCAPE_NS_ACCESS
  35
  36 /* Size of malloc() pool */
  37 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 128 * 1024)
  38
  39 /*SPI device */
  40 #ifdef CONFIG_QSPI_BOOT
  41 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
  42 #define CONFIG_SYS_FMAN_FW_ADDR         0x400d0000
  43 #define CONFIG_ENV_SPI_BUS              0
  44 #define CONFIG_ENV_SPI_CS               0
  45 #define CONFIG_ENV_SPI_MAX_HZ           1000000
  46 #define CONFIG_ENV_SPI_MODE             0x03
  47 #define CONFIG_SPI_FLASH_SPANSION
  48 #define CONFIG_FSL_SPI_INTERFACE
  49 #define CONFIG_SF_DATAFLASH
  50
  51 #define CONFIG_FSL_QSPI
  52 #define QSPI0_AMBA_BASE         0x40000000
  53 #define CONFIG_SPI_FLASH_SPANSION
  54
  55 #define FSL_QSPI_FLASH_SIZE             SZ_64M
  56 #define FSL_QSPI_FLASH_NUM              2
  57
  58 /*
  59  * Environment
  60  */
  61 #define CONFIG_ENV_OVERWRITE
  62
  63 #define CONFIG_ENV_SIZE                 0x40000          /* 256KB */
  64 #define CONFIG_ENV_OFFSET               0x300000        /* 3MB */
  65 #define CONFIG_ENV_SECT_SIZE            0x40000
  66 #endif
  67
  68 /* SATA */
  69 #define CONFIG_SCSI_AHCI_PLAT
  70
  71 #define CONFIG_SYS_SATA                         AHCI_BASE_ADDR
  72
  73 #define CONFIG_SYS_SCSI_MAX_SCSI_ID             1
  74 #define CONFIG_SYS_SCSI_MAX_LUN                 1
  75 #define CONFIG_SYS_SCSI_MAX_DEVICE              (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
  76                                                 CONFIG_SYS_SCSI_MAX_LUN)
  77
  78 /* I2C */
  79 #define CONFIG_SYS_I2C
  80 #define CONFIG_SYS_I2C_MXC
  81 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  82 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  83
  84 #define CONFIG_CONS_INDEX       1
  85 #define CONFIG_SYS_NS16550_SERIAL
  86 #define CONFIG_SYS_NS16550_REG_SIZE     1
  87 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
  88
  89 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
  90
  91 #define CONFIG_SYS_HZ                   1000
  92
  93 #define CONFIG_HWCONFIG
  94 #define HWCONFIG_BUFFER_SIZE            128
  95
  96 #ifndef CONFIG_SPL_BUILD
  97 #define BOOT_TARGET_DEVICES(func) \
  98         func(SCSI, scsi, 0) \
  99         func(MMC, mmc, 0) \
 100         func(USB, usb, 0)
 101 #include <config_distro_bootcmd.h>
 102 #endif
 103
 104 /* Initial environment variables */
 105 #define CONFIG_EXTRA_ENV_SETTINGS               \
 106         "verify=no\0"                           \
 107         "loadaddr=0x80100000\0"                 \
 108         "kernel_addr=0x100000\0"                \
 109         "fdt_high=0xffffffffffffffff\0"         \
 110         "initrd_high=0xffffffffffffffff\0"      \
 111         "kernel_start=0x1000000\0"              \
 112         "kernel_load=0xa0000000\0"              \
 113         "kernel_size=0x2800000\0"               \
 114
 115 #undef CONFIG_BOOTCOMMAND
 116 #define CONFIG_BOOTCOMMAND              "sf probe 0:0; sf read $kernel_load "\
 117                                         "$kernel_start $kernel_size && "\
 118                                         "bootm $kernel_load"
 119
 120 /* Monitor Command Prompt */
 121 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 122 #define CONFIG_SYS_MAXARGS              64      /* max command args */
 123
 124 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 125
 126 #include <asm/arch/soc.h>
 127
 128 #endif /* __LS1012A_COMMON_H */