include/configs/am3517_evm.h

   1 /*
   2  * am3517_evm.h - Default configuration for AM3517 EVM board.
   3  *
   4  * Author: Vaibhav Hiremath <hvaibhav@ti.com>
   5  *
   6  * Based on omap3_evm_config.h
   7  *
   8  * Copyright (C) 2010 Texas Instruments Incorporated
   9  *
  10  * SPDX-License-Identifier:     GPL-2.0+
  11  */
  12
  13 #ifndef __CONFIG_H
  14 #define __CONFIG_H
  15
  16 #define CONFIG_NR_DRAM_BANKS    2       /* CS1 may or may not be populated */
  17
  18 /*
  19  * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
  20  * 64 bytes before this address should be set aside for u-boot.img's
  21  * header. That is 0x800FFFC0--0x80100000 should not be used for any
  22  * other needs.
  23  */
  24
  25 #define CONFIG_SYS_SPL_MALLOC_START     0x80208000
  26 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
  27
  28 #include <configs/ti_omap3_common.h>
  29 #undef CONFIG_SDRC      /* Disable SDRC since we have EMIF4 */
  30
  31 #define CONFIG_MISC_INIT_R
  32 #define CONFIG_REVISION_TAG
  33
  34 /* Hardware drivers */
  35
  36 /* allow to overwrite serial and ethaddr */
  37 #define CONFIG_ENV_OVERWRITE
  38
  39 /*
  40  * USB configuration
  41  * Enable CONFIG_USB_MUSB_HOST for Host functionalities MSC, keyboard
  42  * Enable CONFIG_USB_MUSB_GADGET for Device functionalities.
  43  */
  44
  45 #ifdef CONFIG_USB_MUSB_AM35X
  46
  47 #ifdef CONFIG_USB_MUSB_HOST
  48
  49 #ifdef CONFIG_USB_KEYBOARD
  50 #define CONFIG_PREBOOT "usb start"
  51 #endif /* CONFIG_USB_KEYBOARD */
  52
  53 #endif /* CONFIG_USB_MUSB_HOST */
  54
  55 #endif /* CONFIG_USB_MUSB_AM35X */
  56
  57 /* I2C */
  58
  59 /* Ethernet */
  60 #define CONFIG_DRIVER_TI_EMAC
  61 #define CONFIG_DRIVER_TI_EMAC_USE_RMII
  62 #define CONFIG_MII
  63 #define CONFIG_BOOTP_DEFAULT
  64 #define CONFIG_BOOTP_DNS
  65 #define CONFIG_BOOTP_DNS2
  66 #define CONFIG_BOOTP_SEND_HOSTNAME
  67 #define CONFIG_NET_RETRY_COUNT          10
  68
  69 /* Board NAND Info. */
  70 #ifdef CONFIG_NAND
  71 #define CONFIG_SYS_NAND_ADDR            NAND_BASE       /* physical address */
  72                                                         /* to access nand */
  73 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
  74 #define CONFIG_SYS_NAND_PAGE_COUNT      64
  75 #define CONFIG_SYS_NAND_PAGE_SIZE       2048
  76 #define CONFIG_SYS_NAND_OOBSIZE         64
  77 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
  78 #define CONFIG_SYS_NAND_BAD_BLOCK_POS   NAND_LARGE_BADBLOCK_POS
  79 #define CONFIG_SYS_NAND_ECCPOS          { 2,  3,  4,  5,  6,  7,  8,  9, 10, \
  80                                          11, 12, 13, 14, 16, 17, 18, 19, 20, \
  81                                          21, 22, 23, 24, 25, 26, 27, 28, 30, \
  82                                          31, 32, 33, 34, 35, 36, 37, 38, 39, \
  83                                          40, 41, 42, 44, 45, 46, 47, 48, 49, \
  84                                          50, 51, 52, 53, 54, 55, 56 }
  85
  86 #define CONFIG_SYS_NAND_ECCSIZE         512
  87 #define CONFIG_SYS_NAND_ECCBYTES        13
  88 #define CONFIG_NAND_OMAP_ECCSCHEME      OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
  89 #define CONFIG_SYS_NAND_MAX_OOBFREE     2
  90 #define CONFIG_SYS_NAND_MAX_ECCPOS      56
  91 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
  92 #define CONFIG_SYS_NAND_U_BOOT_OFFS     0x80000
  93 #define CONFIG_MTD_PARTITIONS           /* required for UBI partition support */
  94 #define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
  95 /* NAND block size is 128 KiB.  Synchronize these values with
  96  * corresponding Device Tree entries in Linux:
  97  *  MLO(SPL)             4 * NAND_BLOCK_SIZE = 512 KiB  @ 0x000000
  98  *  U-Boot              15 * NAND_BLOCK_SIZE = 1920 KiB @ 0x080000
  99  *  U-Boot environment   2 * NAND_BLOCK_SIZE = 256 KiB  @ 0x260000
 100  *  Kernel              64 * NAND_BLOCK_SIZE = 8 MiB    @ 0x2A0000
 101  *  DTB                  4 * NAND_BLOCK_SIZE = 512 KiB  @ 0xAA0000
 102  *  RootFS              Remaining Flash Space           @ 0xB20000
 103  */
 104 #endif /* CONFIG_NAND */
 105
 106 /* Environment information */
 107
 108 #define CONFIG_BOOTFILE         "uImage"
 109
 110 #define CONFIG_EXTRA_ENV_SETTINGS \
 111         "loadaddr=0x82000000\0" \
 112         "console=ttyO2,115200n8\0" \
 113         "fdtfile=am3517-evm.dtb\0" \
 114         "fdtaddr=0x82C00000\0" \
 115         "vram=16M\0" \
 116         "bootenv=uEnv.txt\0" \
 117         "cmdline=\0" \
 118         "optargs=\0" \
 119         "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
 120         "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
 121         "mmcdev=0\0" \
 122         "mmcpart=1\0" \
 123         "mmcroot=/dev/mmcblk0p2 rw\0" \
 124         "mmcrootfstype=ext4 rootwait fixrtc\0" \
 125         "mmcargs=setenv bootargs console=${console} " \
 126                 "${mtdparts} " \
 127                 "${optargs} " \
 128                 "root=${mmcroot} " \
 129                 "rootfstype=${mmcrootfstype} " \
 130                 "${cmdline}\0" \
 131         "nandargs=setenv bootargs console=${console} " \
 132                 "${mtdparts} " \
 133                 "${optargs} " \
 134                 "root=ubi0:rootfs rw ubi.mtd=rootfs " \
 135                 "rootfstype=ubifs rootwait " \
 136                 "${cmdline}\0" \
 137         "loadbootenv=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${bootenv}\0"\
 138         "importbootenv=echo Importing environment from mmc ...; " \
 139                 "env import -t ${loadaddr} ${filesize}\0" \
 140         "bootscript=echo Running bootscript from mmc ...; " \
 141                 "source ${loadaddr}\0" \
 142         "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${bootfile}\0" \
 143         "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdtaddr} ${fdtfile}\0" \
 144         "mmcboot=echo Booting from mmc ...; " \
 145                 "run mmcargs; " \
 146                 "bootz ${loadaddr} - ${fdtaddr}\0" \
 147         "nandboot=echo Booting from nand ...; " \
 148                 "run nandargs; " \
 149                 "nand read ${loadaddr} 2a0000 800000; " \
 150                 "nand read ${fdtaddr} aa0000 80000; " \
 151                 "bootm ${loadaddr} - ${fdtaddr}\0" \
 152
 153 #define CONFIG_BOOTCOMMAND \
 154         "mmc dev ${mmcdev}; if mmc rescan; then " \
 155                 "echo SD/MMC found on device $mmcdev; " \
 156                 "if run loadbootenv; then " \
 157                         "run importbootenv; " \
 158                 "fi; " \
 159                 "echo Checking if uenvcmd is set ...; " \
 160                 "if test -n $uenvcmd; then " \
 161                         "echo Running uenvcmd ...; " \
 162                         "run uenvcmd; " \
 163                 "fi; " \
 164                 "echo Running default loadimage ...; " \
 165                 "setenv bootfile zImage; " \
 166                 "if run loadimage; then " \
 167                         "run loadfdt; " \
 168                         "run mmcboot; " \
 169                 "fi; " \
 170         "else run nandboot; fi"
 171
 172 /* Miscellaneous configurable options */
 173 #define CONFIG_AUTO_COMPLETE
 174 #define CONFIG_CMDLINE_EDITING
 175 #define CONFIG_SYS_LONGHELP
 176
 177 /* We set the max number of command args high to avoid HUSH bugs. */
 178 #define CONFIG_SYS_MAXARGS              64
 179
 180 /* Print Buffer Size */
 181 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE \
 182                                         + sizeof(CONFIG_SYS_PROMPT) + 16)
 183 /* Boot Argument Buffer Size */
 184 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 185
 186 /* memtest works on */
 187 #define CONFIG_SYS_MEMTEST_START        (OMAP34XX_SDRC_CS0)
 188 #define CONFIG_SYS_MEMTEST_END          (OMAP34XX_SDRC_CS0 + \
 189                                         0x01F00000) /* 31MB */
 190
 191 /* Physical Memory Map */
 192 #define CONFIG_SYS_CS0_SIZE             (256 * 1024 * 1024)
 193 #define CONFIG_SYS_INIT_RAM_ADDR        0x4020f800
 194 #define CONFIG_SYS_INIT_RAM_SIZE        0x800
 195
 196 /* FLASH and environment organization */
 197
 198 /* **** PISMO SUPPORT *** */
 199 #define CONFIG_SYS_MAX_FLASH_SECT       520     /* max number of sectors */
 200                                                 /* on one chip */
 201 #define CONFIG_SYS_MAX_FLASH_BANKS      2       /* max number of flash banks */
 202 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 2 sectors */
 203
 204 #if defined(CONFIG_NAND)
 205 #define CONFIG_SYS_FLASH_BASE           NAND_BASE
 206 #endif
 207
 208 /* Monitor at start of flash */
 209 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_FLASH_BASE
 210
 211 #define CONFIG_SYS_ENV_SECT_SIZE        (128 << 10)     /* 128 KiB */
 212 #define CONFIG_ENV_SIZE                 CONFIG_SYS_ENV_SECT_SIZE
 213 #define CONFIG_ENV_OFFSET               0x260000
 214 #define CONFIG_ENV_ADDR                 0x260000
 215
 216 /* Defines for SPL */
 217 #define CONFIG_SPL_FRAMEWORK
 218 #undef CONFIG_SPL_TEXT_BASE
 219 #define CONFIG_SPL_TEXT_BASE            0x40200000
 220
 221 #undef CONFIG_SPL_BSS_START_ADDR
 222 #define CONFIG_SPL_BSS_START_ADDR       0x80000000
 223 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000         /* 512 KB */
 224
 225 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION      1
 226 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME         "u-boot.img"
 227
 228 #define CONFIG_SPL_NAND_BASE
 229 #define CONFIG_SPL_NAND_DRIVERS
 230 #define CONFIG_SPL_NAND_ECC
 231
 232 #endif /* __CONFIG_H */