include/configs/T208xQDS.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2011-2013 Freescale Semiconductor, Inc.
   4  */
   5
   6 /*
   7  * T2080/T2081 QDS board configuration file
   8  */
   9
  10 #ifndef __T208xQDS_H
  11 #define __T208xQDS_H
  12
  13 #define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
  14 #if defined(CONFIG_ARCH_T2080)
  15 #define CONFIG_FSL_SATA_V2
  16 #define CONFIG_SYS_SRIO         /* Enable Serial RapidIO Support */
  17 #define CONFIG_SRIO1            /* SRIO port 1 */
  18 #define CONFIG_SRIO2            /* SRIO port 2 */
  19 #elif defined(CONFIG_ARCH_T2081)
  20 #endif
  21
  22 /* High Level Configuration Options */
  23 #define CONFIG_SYS_BOOK3E_HV    /* Category E.HV supported */
  24 #define CONFIG_ENABLE_36BIT_PHYS
  25
  26 #ifdef CONFIG_PHYS_64BIT
  27 #define CONFIG_ADDR_MAP 1
  28 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
  29 #endif
  30
  31 #define CONFIG_SYS_FSL_CPC      /* Corenet Platform Cache */
  32 #define CONFIG_SYS_NUM_CPC      CONFIG_SYS_NUM_DDR_CTLRS
  33 #define CONFIG_ENV_OVERWRITE
  34
  35 #ifdef CONFIG_RAMBOOT_PBL
  36 #define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xqds/t208x_pbi.cfg
  37
  38 #define CONFIG_SPL_FLUSH_IMAGE
  39 #define CONFIG_SPL_PAD_TO               0x40000
  40 #define CONFIG_SPL_MAX_SIZE             0x28000
  41 #define RESET_VECTOR_OFFSET             0x27FFC
  42 #define BOOT_PAGE_OFFSET                0x27000
  43 #ifdef CONFIG_SPL_BUILD
  44 #define CONFIG_SPL_SKIP_RELOCATE
  45 #define CONFIG_SPL_COMMON_INIT_DDR
  46 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
  47 #endif
  48
  49 #ifdef CONFIG_MTD_RAW_NAND
  50 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
  51 #define CONFIG_SYS_NAND_U_BOOT_DST      0x00200000
  52 #define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
  53 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (256 << 10)
  54 #if defined(CONFIG_ARCH_T2080)
  55 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2080_nand_rcw.cfg
  56 #elif defined(CONFIG_ARCH_T2081)
  57 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2081_nand_rcw.cfg
  58 #endif
  59 #endif
  60
  61 #ifdef CONFIG_SPIFLASH
  62 #define CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  63 #define CONFIG_SPL_SPI_FLASH_MINIMAL
  64 #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE        (768 << 10)
  65 #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST         (0x00200000)
  66 #define CONFIG_SYS_SPI_FLASH_U_BOOT_START       (0x00200000)
  67 #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS        (256 << 10)
  68 #ifndef CONFIG_SPL_BUILD
  69 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  70 #endif
  71 #if defined(CONFIG_ARCH_T2080)
  72 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2080_spi_rcw.cfg
  73 #elif defined(CONFIG_ARCH_T2081)
  74 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2081_spi_rcw.cfg
  75 #endif
  76 #endif
  77
  78 #ifdef CONFIG_SDCARD
  79 #define CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
  80 #define CONFIG_SYS_MMC_U_BOOT_SIZE      (768 << 10)
  81 #define CONFIG_SYS_MMC_U_BOOT_DST       (0x00200000)
  82 #define CONFIG_SYS_MMC_U_BOOT_START     (0x00200000)
  83 #define CONFIG_SYS_MMC_U_BOOT_OFFS      (260 << 10)
  84 #ifndef CONFIG_SPL_BUILD
  85 #define CONFIG_SYS_MPC85XX_NO_RESETVEC
  86 #endif
  87 #if defined(CONFIG_ARCH_T2080)
  88 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2080_sd_rcw.cfg
  89 #elif defined(CONFIG_ARCH_T2081)
  90 #define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xqds/t2081_sd_rcw.cfg
  91 #endif
  92 #endif
  93
  94 #endif /* CONFIG_RAMBOOT_PBL */
  95
  96 #define CONFIG_SRIO_PCIE_BOOT_MASTER
  97 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
  98 /* Set 1M boot space */
  99 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
 100 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
 101                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
 102 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
 103 #endif
 104
 105 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 106 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
 107 #endif
 108
 109 /*
 110  * These can be toggled for performance analysis, otherwise use default.
 111  */
 112 #define CONFIG_SYS_CACHE_STASHING
 113 #define CONFIG_BTB              /* toggle branch predition */
 114 #define CONFIG_DDR_ECC
 115 #ifdef CONFIG_DDR_ECC
 116 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 117 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
 118 #endif
 119
 120 #if defined(CONFIG_SPIFLASH)
 121 #elif defined(CONFIG_SDCARD)
 122 #define CONFIG_SYS_MMC_ENV_DEV  0
 123 #endif
 124
 125 #ifndef __ASSEMBLY__
 126 unsigned long get_board_sys_clk(void);
 127 unsigned long get_board_ddr_clk(void);
 128 #endif
 129
 130 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk()
 131 #define CONFIG_DDR_CLK_FREQ     get_board_ddr_clk()
 132
 133 /*
 134  * Config the L3 Cache as L3 SRAM
 135  */
 136 #define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
 137 #define CONFIG_SYS_L3_SIZE              (512 << 10)
 138 #define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
 139 #define SPL_ENV_ADDR                    (CONFIG_SPL_GD_ADDR + 4 * 1024)
 140 #define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
 141 #define CONFIG_SPL_RELOC_MALLOC_SIZE    (50 << 10)
 142 #define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)
 143
 144 #define CONFIG_SYS_DCSRBAR      0xf0000000
 145 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
 146
 147 /* EEPROM */
 148 #define CONFIG_ID_EEPROM
 149 #define CONFIG_SYS_I2C_EEPROM_NXID
 150 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 151 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x57
 152 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
 153
 154 /*
 155  * DDR Setup
 156  */
 157 #define CONFIG_VERY_BIG_RAM
 158 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 159 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 160 #define CONFIG_DIMM_SLOTS_PER_CTLR      2
 161 #define CONFIG_CHIP_SELECTS_PER_CTRL    (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 162 #define CONFIG_DDR_SPD
 163 #define CONFIG_SYS_SPD_BUS_NUM  0
 164 #define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
 165 #define SPD_EEPROM_ADDRESS1     0x51
 166 #define SPD_EEPROM_ADDRESS2     0x52
 167 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
 168 #define CTRL_INTLV_PREFERED     cacheline
 169
 170 /*
 171  * IFC Definitions
 172  */
 173 #define CONFIG_SYS_FLASH_BASE           0xe0000000
 174 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 175 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
 176 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
 177                                 + 0x8000000) | \
 178                                 CSPR_PORT_SIZE_16 | \
 179                                 CSPR_MSEL_NOR | \
 180                                 CSPR_V)
 181 #define CONFIG_SYS_NOR1_CSPR_EXT        (0xf)
 182 #define CONFIG_SYS_NOR1_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 183                                 CSPR_PORT_SIZE_16 | \
 184                                 CSPR_MSEL_NOR | \
 185                                 CSPR_V)
 186 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)
 187 /* NOR Flash Timing Params */
 188 #define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80
 189
 190 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
 191                                 FTIM0_NOR_TEADC(0x5) | \
 192                                 FTIM0_NOR_TEAHC(0x5))
 193 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 194                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 195                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 196 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 197                                 FTIM2_NOR_TCH(0x4) | \
 198                                 FTIM2_NOR_TWPH(0x0E) | \
 199                                 FTIM2_NOR_TWP(0x1c))
 200 #define CONFIG_SYS_NOR_FTIM3    0x0
 201
 202 #define CONFIG_SYS_FLASH_QUIET_TEST
 203 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 204
 205 #define CONFIG_SYS_MAX_FLASH_BANKS      2       /* number of banks */
 206 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 207 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 208 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 209
 210 #define CONFIG_SYS_FLASH_EMPTY_INFO
 211 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS \
 212                                         + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
 213
 214 #define CONFIG_FSL_QIXIS        /* use common QIXIS code */
 215 #define QIXIS_BASE                      0xffdf0000
 216 #define QIXIS_LBMAP_SWITCH              6
 217 #define QIXIS_LBMAP_MASK                0x0f
 218 #define QIXIS_LBMAP_SHIFT               0
 219 #define QIXIS_LBMAP_DFLTBANK            0x00
 220 #define QIXIS_LBMAP_ALTBANK             0x04
 221 #define QIXIS_LBMAP_NAND                0x09
 222 #define QIXIS_LBMAP_SD                  0x00
 223 #define QIXIS_RCW_SRC_NAND              0x104
 224 #define QIXIS_RCW_SRC_SD                0x040
 225 #define QIXIS_RST_CTL_RESET             0x83
 226 #define QIXIS_RST_FORCE_MEM             0x1
 227 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 228 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 229 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 230 #define QIXIS_BASE_PHYS         (0xf00000000ull | QIXIS_BASE)
 231
 232 #define CONFIG_SYS_CSPR3_EXT    (0xf)
 233 #define CONFIG_SYS_CSPR3        (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
 234                                 | CSPR_PORT_SIZE_8 \
 235                                 | CSPR_MSEL_GPCM \
 236                                 | CSPR_V)
 237 #define CONFIG_SYS_AMASK3       IFC_AMASK(64 * 1024)
 238 #define CONFIG_SYS_CSOR3        0x0
 239 /* QIXIS Timing parameters for IFC CS3 */
 240 #define CONFIG_SYS_CS3_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 241                                         FTIM0_GPCM_TEADC(0x0e) | \
 242                                         FTIM0_GPCM_TEAHC(0x0e))
 243 #define CONFIG_SYS_CS3_FTIM1            (FTIM1_GPCM_TACO(0xff) | \
 244                                         FTIM1_GPCM_TRAD(0x3f))
 245 #define CONFIG_SYS_CS3_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 246                                         FTIM2_GPCM_TCH(0x8) | \
 247                                         FTIM2_GPCM_TWP(0x1f))
 248 #define CONFIG_SYS_CS3_FTIM3            0x0
 249
 250 /* NAND Flash on IFC */
 251 #define CONFIG_NAND_FSL_IFC
 252 #define CONFIG_SYS_NAND_BASE            0xff800000
 253 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 254
 255 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 256 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 257                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 258                                 | CSPR_MSEL_NAND         /* MSEL = NAND */ \
 259                                 | CSPR_V)
 260 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)
 261
 262 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 263                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 264                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */     \
 265                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */   \
 266                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */\
 267                                 | CSOR_NAND_SPRZ_64     /* Spare size = 64 */\
 268                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 269
 270 #define CONFIG_SYS_NAND_ONFI_DETECTION
 271
 272 /* ONFI NAND Flash mode0 Timing Params */
 273 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 274                                         FTIM0_NAND_TWP(0x18)    | \
 275                                         FTIM0_NAND_TWCHT(0x07)  | \
 276                                         FTIM0_NAND_TWH(0x0a))
 277 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 278                                         FTIM1_NAND_TWBE(0x39)   | \
 279                                         FTIM1_NAND_TRR(0x0e)    | \
 280                                         FTIM1_NAND_TRP(0x18))
 281 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f)  | \
 282                                         FTIM2_NAND_TREH(0x0a)   | \
 283                                         FTIM2_NAND_TWHRE(0x1e))
 284 #define CONFIG_SYS_NAND_FTIM3           0x0
 285
 286 #define CONFIG_SYS_NAND_DDR_LAW         11
 287 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 288 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 289 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 290
 291 #if defined(CONFIG_MTD_RAW_NAND)
 292 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 293 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 294 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 295 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 296 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 297 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 298 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 299 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 300 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 301 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
 302 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 303 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 304 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 305 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 306 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 307 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 308 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NOR1_CSPR_EXT
 309 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NOR1_CSPR
 310 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NOR_AMASK
 311 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NOR_CSOR
 312 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NOR_FTIM0
 313 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NOR_FTIM1
 314 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NOR_FTIM2
 315 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NOR_FTIM3
 316 #else
 317 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 318 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 319 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 320 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 321 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 322 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 323 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 324 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 325 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR1_CSPR_EXT
 326 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR1_CSPR
 327 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 328 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 329 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 330 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 331 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 332 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 333 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NAND_CSPR_EXT
 334 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NAND_CSPR
 335 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NAND_AMASK
 336 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NAND_CSOR
 337 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NAND_FTIM0
 338 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NAND_FTIM1
 339 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NAND_FTIM2
 340 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NAND_FTIM3
 341 #endif
 342
 343 #if defined(CONFIG_RAMBOOT_PBL)
 344 #define CONFIG_SYS_RAMBOOT
 345 #endif
 346
 347 #ifdef CONFIG_SPL_BUILD
 348 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
 349 #else
 350 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
 351 #endif
 352
 353 #define CONFIG_HWCONFIG
 354
 355 /* define to use L1 as initial stack */
 356 #define CONFIG_L1_INIT_RAM
 357 #define CONFIG_SYS_INIT_RAM_LOCK
 358 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000 /* Initial L1 address */
 359 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 360 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
 361 /* The assembler doesn't like typecast */
 362 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 363                         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 364                         CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 365 #define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
 366 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 367                                                 GENERATED_GBL_DATA_SIZE)
 368 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 369 #define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
 370 #define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)
 371
 372 /*
 373  * Serial Port
 374  */
 375 #define CONFIG_SYS_NS16550_SERIAL
 376 #define CONFIG_SYS_NS16550_REG_SIZE     1
 377 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 378 #define CONFIG_SYS_BAUDRATE_TABLE       \
 379         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 380 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 381 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 382 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 383 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 384
 385 /*
 386  * I2C
 387  */
 388 #define CONFIG_SYS_I2C
 389 #define CONFIG_SYS_I2C_FSL
 390 #define CONFIG_SYS_FSL_I2C_SLAVE   0x7F
 391 #define CONFIG_SYS_FSL_I2C2_SLAVE  0x7F
 392 #define CONFIG_SYS_FSL_I2C3_SLAVE  0x7F
 393 #define CONFIG_SYS_FSL_I2C4_SLAVE  0x7F
 394 #define CONFIG_SYS_FSL_I2C_OFFSET  0x118000
 395 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
 396 #define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
 397 #define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
 398 #define CONFIG_SYS_FSL_I2C_SPEED   100000
 399 #define CONFIG_SYS_FSL_I2C2_SPEED  100000
 400 #define CONFIG_SYS_FSL_I2C3_SPEED  100000
 401 #define CONFIG_SYS_FSL_I2C4_SPEED  100000
 402 #define I2C_MUX_PCA_ADDR_PRI    0x77 /* I2C bus multiplexer,primary */
 403 #define I2C_MUX_PCA_ADDR_SEC1   0x75 /* I2C bus multiplexer,secondary 1 */
 404 #define I2C_MUX_PCA_ADDR_SEC2   0x76 /* I2C bus multiplexer,secondary 2 */
 405 #define I2C_MUX_CH_DEFAULT      0x8
 406
 407 #define I2C_MUX_CH_VOL_MONITOR 0xa
 408
 409 /* Voltage monitor on channel 2*/
 410 #define I2C_VOL_MONITOR_ADDR           0x40
 411 #define I2C_VOL_MONITOR_BUS_V_OFFSET   0x2
 412 #define I2C_VOL_MONITOR_BUS_V_OVF      0x1
 413 #define I2C_VOL_MONITOR_BUS_V_SHIFT    3
 414
 415 #define CONFIG_VID_FLS_ENV              "t208xqds_vdd_mv"
 416 #ifndef CONFIG_SPL_BUILD
 417 #define CONFIG_VID
 418 #endif
 419 #define CONFIG_VOL_MONITOR_IR36021_SET
 420 #define CONFIG_VOL_MONITOR_IR36021_READ
 421 /* The lowest and highest voltage allowed for T208xQDS */
 422 #define VDD_MV_MIN                      819
 423 #define VDD_MV_MAX                      1212
 424
 425 /*
 426  * RapidIO
 427  */
 428 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 429 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 430 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000 /* 256M */
 431 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 432 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 433 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000 /* 256M */
 434 /*
 435  * for slave u-boot IMAGE instored in master memory space,
 436  * PHYS must be aligned based on the SIZE
 437  */
 438 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
 439 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
 440 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
 441 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
 442 /*
 443  * for slave UCODE and ENV instored in master memory space,
 444  * PHYS must be aligned based on the SIZE
 445  */
 446 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
 447 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 448 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000 /* 256K */
 449
 450 /* slave core release by master*/
 451 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 452 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 453
 454 /*
 455  * SRIO_PCIE_BOOT - SLAVE
 456  */
 457 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 458 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 459 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 460                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 461 #endif
 462
 463 /*
 464  * eSPI - Enhanced SPI
 465  */
 466
 467 /*
 468  * General PCI
 469  * Memory space is mapped 1-1, but I/O space must start from 0.
 470  */
 471 #define CONFIG_PCIE1            /* PCIE controller 1 */
 472 #define CONFIG_PCIE2            /* PCIE controller 2 */
 473 #define CONFIG_PCIE3            /* PCIE controller 3 */
 474 #define CONFIG_PCIE4            /* PCIE controller 4 */
 475 #define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
 476 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 477 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 478 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 479 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 480 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 481
 482 /* controller 2, Slot 2, tgtid 2, Base address 201000 */
 483 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 484 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 485 #define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
 486 #define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull
 487
 488 /* controller 3, Slot 1, tgtid 1, Base address 202000 */
 489 #define CONFIG_SYS_PCIE3_MEM_VIRT       0xb0000000
 490 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc30000000ull
 491 #define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
 492 #define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull
 493
 494 /* controller 4, Base address 203000 */
 495 #define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
 496 #define CONFIG_SYS_PCIE4_MEM_PHYS       0xc40000000ull
 497 #define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull
 498
 499 #ifdef CONFIG_PCI
 500 #if !defined(CONFIG_DM_PCI)
 501 #define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
 502 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 503 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 504 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 505 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 506 #define CONFIG_SYS_PCIE2_MEM_BUS        0xe0000000
 507 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000 /* 256M */
 508 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 509 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 510 #define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
 511 #define CONFIG_SYS_PCIE3_MEM_SIZE       0x10000000      /* 256M */
 512 #define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
 513 #define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */
 514 #define CONFIG_SYS_PCIE4_MEM_BUS        0xe0000000
 515 #define CONFIG_SYS_PCIE4_MEM_SIZE       0x10000000      /* 256M */
 516 #define CONFIG_SYS_PCIE4_IO_BUS         0x00000000
 517 #define CONFIG_SYS_PCIE4_IO_SIZE        0x00010000      /* 64k */
 518 #define CONFIG_PCI_INDIRECT_BRIDGE
 519 #endif
 520 #define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
 521 #endif
 522
 523 /* Qman/Bman */
 524 #ifndef CONFIG_NOBQFMAN
 525 #define CONFIG_SYS_BMAN_NUM_PORTALS     18
 526 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 527 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 528 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 529 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 530 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 531 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 532 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 533 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 534                                         CONFIG_SYS_BMAN_CENA_SIZE)
 535 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 536 #define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
 537 #define CONFIG_SYS_QMAN_NUM_PORTALS     18
 538 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 539 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 540 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 541 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 542 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 543 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 544 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 545 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 546                                         CONFIG_SYS_QMAN_CENA_SIZE)
 547 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 548 #define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08
 549
 550 #define CONFIG_SYS_DPAA_FMAN
 551 #define CONFIG_SYS_DPAA_PME
 552 #define CONFIG_SYS_PMAN
 553 #define CONFIG_SYS_DPAA_DCE
 554 #define CONFIG_SYS_DPAA_RMAN            /* RMan */
 555 #define CONFIG_SYS_INTERLAKEN
 556
 557 /* Default address of microcode for the Linux Fman driver */
 558 #if defined(CONFIG_SPIFLASH)
 559 /*
 560  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 561  * env, so we got 0x110000.
 562  */
 563 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000
 564 #elif defined(CONFIG_SDCARD)
 565 /*
 566  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 567  * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 568  * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
 569  */
 570 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
 571 #elif defined(CONFIG_MTD_RAW_NAND)
 572 #define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE)
 573 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 574 /*
 575  * Slave has no ucode locally, it can fetch this from remote. When implementing
 576  * in two corenet boards, slave's ucode could be stored in master's memory
 577  * space, the address can be mapped from slave TLB->slave LAW->
 578  * slave SRIO or PCIE outbound window->master inbound window->
 579  * master LAW->the ucode address in master's memory space.
 580  */
 581 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
 582 #else
 583 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
 584 #endif
 585 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 586 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 587 #endif /* CONFIG_NOBQFMAN */
 588
 589 #ifdef CONFIG_SYS_DPAA_FMAN
 590 #define CONFIG_PHY_VITESSE
 591 #define CONFIG_PHY_REALTEK
 592 #define CONFIG_PHY_TERANETICS
 593 #define RGMII_PHY1_ADDR 0x1
 594 #define RGMII_PHY2_ADDR 0x2
 595 #define FM1_10GEC1_PHY_ADDR       0x3
 596 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C
 597 #define SGMII_CARD_PORT2_PHY_ADDR 0x1D
 598 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E
 599 #define SGMII_CARD_PORT4_PHY_ADDR 0x1F
 600 #endif
 601
 602 #ifdef CONFIG_FMAN_ENET
 603 #define CONFIG_ETHPRIME         "FM1@DTSEC3"
 604 #endif
 605
 606 /*
 607  * SATA
 608  */
 609 #ifdef CONFIG_FSL_SATA_V2
 610 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 611 #define CONFIG_SATA1
 612 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 613 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 614 #define CONFIG_SATA2
 615 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 616 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 617 #define CONFIG_LBA48
 618 #endif
 619
 620 /*
 621  * USB
 622  */
 623 #ifdef CONFIG_USB_EHCI_HCD
 624 #define CONFIG_USB_EHCI_FSL
 625 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 626 #define CONFIG_HAS_FSL_DR_USB
 627 #endif
 628
 629 /*
 630  * SDHC
 631  */
 632 #ifdef CONFIG_MMC
 633 #define CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK
 634 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 635 #define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
 636 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 637 #define CONFIG_FSL_ESDHC_ADAPTER_IDENT
 638 #endif
 639
 640 /*
 641  * Dynamic MTD Partition support with mtdparts
 642  */
 643
 644 /*
 645  * Environment
 646  */
 647 #define CONFIG_LOADS_ECHO       /* echo on for serial download */
 648 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 649
 650 /*
 651  * Miscellaneous configurable options
 652  */
 653 #define CONFIG_SYS_LOAD_ADDR    0x2000000 /* default load address */
 654
 655 /*
 656  * For booting Linux, the board info and command line data
 657  * have to be in the first 64 MB of memory, since this is
 658  * the maximum mapped by the Linux kernel during initialization.
 659  */
 660 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 661 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 662
 663 #ifdef CONFIG_CMD_KGDB
 664 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 665 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 666 #endif
 667
 668 /*
 669  * Environment Configuration
 670  */
 671 #define CONFIG_ROOTPATH  "/opt/nfsroot"
 672 #define CONFIG_BOOTFILE  "uImage"
 673 #define CONFIG_UBOOTPATH "u-boot.bin"   /* U-Boot image on TFTP server */
 674
 675 /* default location for tftp and bootm */
 676 #define CONFIG_LOADADDR         1000000
 677 #define __USB_PHY_TYPE          utmi
 678
 679 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 680         "hwconfig=fsl_ddr:"                                     \
 681         "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
 682         "bank_intlv=auto;"                                      \
 683         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 684         "netdev=eth0\0"                                         \
 685         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
 686         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
 687         "tftpflash=tftpboot $loadaddr $uboot && "               \
 688         "protect off $ubootaddr +$filesize && "                 \
 689         "erase $ubootaddr +$filesize && "                       \
 690         "cp.b $loadaddr $ubootaddr $filesize && "               \
 691         "protect on $ubootaddr +$filesize && "                  \
 692         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 693         "consoledev=ttyS0\0"                                    \
 694         "ramdiskaddr=2000000\0"                                 \
 695         "ramdiskfile=t2080qds/ramdisk.uboot\0"                  \
 696         "fdtaddr=1e00000\0"                                     \
 697         "fdtfile=t2080qds/t2080qds.dtb\0"                       \
 698         "bdev=sda3\0"
 699
 700 /*
 701  * For emulation this causes u-boot to jump to the start of the
 702  * proof point app code automatically
 703  */
 704 #define CONFIG_PROOF_POINTS                             \
 705         "setenv bootargs root=/dev/$bdev rw "           \
 706         "console=$consoledev,$baudrate $othbootargs;"   \
 707         "cpu 1 release 0x29000000 - - -;"               \
 708         "cpu 2 release 0x29000000 - - -;"               \
 709         "cpu 3 release 0x29000000 - - -;"               \
 710         "cpu 4 release 0x29000000 - - -;"               \
 711         "cpu 5 release 0x29000000 - - -;"               \
 712         "cpu 6 release 0x29000000 - - -;"               \
 713         "cpu 7 release 0x29000000 - - -;"               \
 714         "go 0x29000000"
 715
 716 #define CONFIG_HVBOOT                           \
 717         "setenv bootargs config-addr=0x60000000; "      \
 718         "bootm 0x01000000 - 0x00f00000"
 719
 720 #define CONFIG_ALU                              \
 721         "setenv bootargs root=/dev/$bdev rw "           \
 722         "console=$consoledev,$baudrate $othbootargs;"   \
 723         "cpu 1 release 0x01000000 - - -;"               \
 724         "cpu 2 release 0x01000000 - - -;"               \
 725         "cpu 3 release 0x01000000 - - -;"               \
 726         "cpu 4 release 0x01000000 - - -;"               \
 727         "cpu 5 release 0x01000000 - - -;"               \
 728         "cpu 6 release 0x01000000 - - -;"               \
 729         "cpu 7 release 0x01000000 - - -;"               \
 730         "go 0x01000000"
 731
 732 #define CONFIG_LINUX                            \
 733         "setenv bootargs root=/dev/ram rw "             \
 734         "console=$consoledev,$baudrate $othbootargs;"   \
 735         "setenv ramdiskaddr 0x02000000;"                \
 736         "setenv fdtaddr 0x00c00000;"                    \
 737         "setenv loadaddr 0x1000000;"                    \
 738         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 739
 740 #define CONFIG_HDBOOT                                   \
 741         "setenv bootargs root=/dev/$bdev rw "           \
 742         "console=$consoledev,$baudrate $othbootargs;"   \
 743         "tftp $loadaddr $bootfile;"                     \
 744         "tftp $fdtaddr $fdtfile;"                       \
 745         "bootm $loadaddr - $fdtaddr"
 746
 747 #define CONFIG_NFSBOOTCOMMAND                   \
 748         "setenv bootargs root=/dev/nfs rw "     \
 749         "nfsroot=$serverip:$rootpath "          \
 750         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 751         "console=$consoledev,$baudrate $othbootargs;"   \
 752         "tftp $loadaddr $bootfile;"             \
 753         "tftp $fdtaddr $fdtfile;"               \
 754         "bootm $loadaddr - $fdtaddr"
 755
 756 #define CONFIG_RAMBOOTCOMMAND                           \
 757         "setenv bootargs root=/dev/ram rw "             \
 758         "console=$consoledev,$baudrate $othbootargs;"   \
 759         "tftp $ramdiskaddr $ramdiskfile;"               \
 760         "tftp $loadaddr $bootfile;"                     \
 761         "tftp $fdtaddr $fdtfile;"                       \
 762         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 763
 764 #define CONFIG_BOOTCOMMAND              CONFIG_LINUX
 765
 766 #include <asm/fsl_secure_boot.h>
 767
 768 #endif  /* __T208xQDS_H */