board/solidrun/mx6cuboxi/mx6cuboxi.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * Copyright (C) 2015 Freescale Semiconductor, Inc.
   4  *
   5  * Author: Fabio Estevam <fabio.estevam@freescale.com>
   6  *
   7  * Copyright (C) 2013 Jon Nettleton <jon.nettleton@gmail.com>
   8  *
   9  * Based on SPL code from Solidrun tree, which is:
  10  * Author: Tungyi Lin <tungyilin1127@gmail.com>
  11  *
  12  * Derived from EDM_CF_IMX6 code by TechNexion,Inc
  13  * Ported to SolidRun microSOM by Rabeeh Khoury <rabeeh@solid-run.com>
  14  */
  15
  16 #include <asm/arch/clock.h>
  17 #include <asm/arch/imx-regs.h>
  18 #include <asm/arch/iomux.h>
  19 #include <asm/arch/mx6-pins.h>
  20 #include <asm/arch/mxc_hdmi.h>
  21 #include <linux/errno.h>
  22 #include <asm/gpio.h>
  23 #include <asm/mach-imx/iomux-v3.h>
  24 #include <asm/mach-imx/sata.h>
  25 #include <asm/mach-imx/video.h>
  26 #include <mmc.h>
  27 #include <fsl_esdhc_imx.h>
  28 #include <malloc.h>
  29 #include <miiphy.h>
  30 #include <netdev.h>
  31 #include <asm/arch/crm_regs.h>
  32 #include <asm/io.h>
  33 #include <asm/arch/sys_proto.h>
  34 #include <spl.h>
  35 #include <usb.h>
  36 #include <usb/ehci-ci.h>
  37
  38 DECLARE_GLOBAL_DATA_PTR;
  39
  40 #define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |                   \
  41         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |                 \
  42         PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  43
  44 #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |                    \
  45         PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |                 \
  46         PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  47
  48 #define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |                   \
  49         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
  50
  51 #define ENET_PAD_CTRL_PD  (PAD_CTL_PUS_100K_DOWN |              \
  52         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
  53
  54 #define ENET_PAD_CTRL_CLK  ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \
  55         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
  56
  57 #define ETH_PHY_RESET   IMX_GPIO_NR(4, 15)
  58 #define USB_H1_VBUS     IMX_GPIO_NR(1, 0)
  59
  60 enum board_type {
  61         CUBOXI          = 0x00,
  62         HUMMINGBOARD    = 0x01,
  63         HUMMINGBOARD2   = 0x02,
  64         UNKNOWN         = 0x03,
  65 };
  66
  67 #define MEM_STRIDE 0x4000000
  68 static u32 get_ram_size_stride_test(u32 *base, u32 maxsize)
  69 {
  70         volatile u32 *addr;
  71         u32          save[64];
  72         u32          cnt;
  73         u32          size;
  74         int          i = 0;
  75
  76         /* First save the data */
  77         for (cnt = 0; cnt < maxsize; cnt += MEM_STRIDE) {
  78                 addr = (volatile u32 *)((u32)base + cnt);       /* pointer arith! */
  79                 sync ();
  80                 save[i++] = *addr;
  81                 sync ();
  82         }
  83
  84         /* First write a signature */
  85         * (volatile u32 *)base = 0x12345678;
  86         for (size = MEM_STRIDE; size < maxsize; size += MEM_STRIDE) {
  87                 * (volatile u32 *)((u32)base + size) = size;
  88                 sync ();
  89                 if (* (volatile u32 *)((u32)base) == size) {    /* We reached the overlapping address */
  90                         break;
  91                 }
  92         }
  93
  94         /* Restore the data */
  95         for (cnt = (maxsize - MEM_STRIDE); i > 0; cnt -= MEM_STRIDE) {
  96                 addr = (volatile u32 *)((u32)base + cnt);       /* pointer arith! */
  97                 sync ();
  98                 *addr = save[i--];
  99                 sync ();
 100         }
 101
 102         return (size);
 103 }
 104
 105 int dram_init(void)
 106 {
 107         u32 max_size = imx_ddr_size();
 108
 109         gd->ram_size = get_ram_size_stride_test((u32 *) CONFIG_SYS_SDRAM_BASE,
 110                                                 (u32)max_size);
 111
 112         return 0;
 113 }
 114
 115 static iomux_v3_cfg_t const uart1_pads[] = {
 116         IOMUX_PADS(PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
 117         IOMUX_PADS(PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
 118 };
 119
 120 static iomux_v3_cfg_t const usdhc2_pads[] = {
 121         IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 122         IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 123         IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 124         IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1      | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 125         IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2      | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 126         IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3      | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 127 };
 128
 129 static iomux_v3_cfg_t const usdhc3_pads[] = {
 130         IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 131         IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 132         IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 133         IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1      | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 134         IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2      | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 135         IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3      | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 136         IOMUX_PADS(PAD_SD3_DAT4__SD3_DATA4      | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 137         IOMUX_PADS(PAD_SD3_DAT5__SD3_DATA5      | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 138         IOMUX_PADS(PAD_SD3_DAT6__SD3_DATA6      | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 139         IOMUX_PADS(PAD_SD3_DAT7__SD3_DATA7      | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 140         IOMUX_PADS(PAD_SD3_RST__SD3_RESET       | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 141 };
 142
 143 static iomux_v3_cfg_t const board_detect[] = {
 144         /* These pins are for sensing if it is a CuBox-i or a HummingBoard */
 145         IOMUX_PADS(PAD_KEY_ROW1__GPIO4_IO09  | MUX_PAD_CTRL(UART_PAD_CTRL)),
 146         IOMUX_PADS(PAD_EIM_DA4__GPIO3_IO04   | MUX_PAD_CTRL(UART_PAD_CTRL)),
 147         IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08  | MUX_PAD_CTRL(UART_PAD_CTRL)),
 148 };
 149
 150 static iomux_v3_cfg_t const som_rev_detect[] = {
 151         /* These pins are for sensing if it is a CuBox-i or a HummingBoard */
 152         IOMUX_PADS(PAD_CSI0_DAT14__GPIO6_IO00  | MUX_PAD_CTRL(UART_PAD_CTRL)),
 153         IOMUX_PADS(PAD_CSI0_DAT18__GPIO6_IO04  | MUX_PAD_CTRL(UART_PAD_CTRL)),
 154 };
 155
 156 static iomux_v3_cfg_t const usb_pads[] = {
 157         IOMUX_PADS(PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL)),
 158 };
 159
 160 static void setup_iomux_uart(void)
 161 {
 162         SETUP_IOMUX_PADS(uart1_pads);
 163 }
 164
 165 static struct fsl_esdhc_cfg usdhc_cfg = {
 166         .esdhc_base = USDHC2_BASE_ADDR,
 167         .max_bus_width = 4,
 168 };
 169
 170 static struct fsl_esdhc_cfg emmc_cfg = {
 171         .esdhc_base = USDHC3_BASE_ADDR,
 172         .max_bus_width = 8,
 173 };
 174
 175 int board_mmc_get_env_dev(int devno)
 176 {
 177         return devno - 1;
 178 }
 179
 180 #define USDHC2_CD_GPIO  IMX_GPIO_NR(1, 4)
 181
 182 int board_mmc_getcd(struct mmc *mmc)
 183 {
 184         struct fsl_esdhc_cfg *cfg = mmc->priv;
 185         int ret = 0;
 186
 187         switch (cfg->esdhc_base) {
 188         case USDHC2_BASE_ADDR:
 189                 ret = !gpio_get_value(USDHC2_CD_GPIO);
 190                 break;
 191         case USDHC3_BASE_ADDR:
 192                 ret = (mmc_get_op_cond(mmc) < 0) ? 0 : 1; /* eMMC/uSDHC3 has no CD GPIO */
 193                 break;
 194         }
 195
 196         return ret;
 197 }
 198
 199 static int mmc_init_main(bd_t *bis)
 200 {
 201         int ret;
 202
 203         /*
 204          * Following map is done:
 205          * (U-Boot device node)    (Physical Port)
 206          * mmc0                    Carrier board MicroSD
 207          * mmc1                    SOM eMMC
 208          */
 209         SETUP_IOMUX_PADS(usdhc2_pads);
 210         usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
 211         ret = fsl_esdhc_initialize(bis, &usdhc_cfg);
 212         if (ret)
 213                 return ret;
 214
 215         SETUP_IOMUX_PADS(usdhc3_pads);
 216         emmc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
 217         return fsl_esdhc_initialize(bis, &emmc_cfg);
 218 }
 219
 220 static int mmc_init_spl(bd_t *bis)
 221 {
 222         struct src *psrc = (struct src *)SRC_BASE_ADDR;
 223         unsigned reg = readl(&psrc->sbmr1) >> 11;
 224
 225         /*
 226          * Upon reading BOOT_CFG register the following map is done:
 227          * Bit 11 and 12 of BOOT_CFG register can determine the current
 228          * mmc port
 229          * 0x1                  SD2
 230          * 0x2                  SD3
 231          */
 232         switch (reg & 0x3) {
 233         case 0x1:
 234                 SETUP_IOMUX_PADS(usdhc2_pads);
 235                 usdhc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
 236                 gd->arch.sdhc_clk = usdhc_cfg.sdhc_clk;
 237                 return fsl_esdhc_initialize(bis, &usdhc_cfg);
 238         case 0x2:
 239                 SETUP_IOMUX_PADS(usdhc3_pads);
 240                 emmc_cfg.sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
 241                 gd->arch.sdhc_clk = emmc_cfg.sdhc_clk;
 242                 return fsl_esdhc_initialize(bis, &emmc_cfg);
 243         }
 244
 245         return -ENODEV;
 246 }
 247
 248 int board_mmc_init(bd_t *bis)
 249 {
 250         if (IS_ENABLED(CONFIG_SPL_BUILD))
 251                 return mmc_init_spl(bis);
 252
 253         return mmc_init_main(bis);
 254 }
 255
 256 static iomux_v3_cfg_t const enet_pads[] = {
 257         IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 258         IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 259         /* AR8035 reset */
 260         IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
 261         /* AR8035 interrupt */
 262         IOMUX_PADS(PAD_DI0_PIN2__GPIO4_IO18 | MUX_PAD_CTRL(NO_PAD_CTRL)),
 263         /* GPIO16 -> AR8035 25MHz */
 264         IOMUX_PADS(PAD_GPIO_16__ENET_REF_CLK      | MUX_PAD_CTRL(NO_PAD_CTRL)),
 265         IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC       | MUX_PAD_CTRL(NO_PAD_CTRL)),
 266         IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 267         IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 268         IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 269         IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 270         IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 271         /* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
 272         IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL_CLK)),
 273         IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 274         IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
 275         IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
 276         IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 277         IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 278         IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
 279         IOMUX_PADS(PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
 280         IOMUX_PADS(PAD_ENET_RXD1__GPIO1_IO26 | MUX_PAD_CTRL(ENET_PAD_CTRL_PD)),
 281 };
 282
 283 static void setup_iomux_enet(void)
 284 {
 285         SETUP_IOMUX_PADS(enet_pads);
 286
 287         gpio_direction_output(ETH_PHY_RESET, 0);
 288         mdelay(10);
 289         gpio_set_value(ETH_PHY_RESET, 1);
 290         udelay(100);
 291 }
 292
 293 int board_phy_config(struct phy_device *phydev)
 294 {
 295         if (phydev->drv->config)
 296                 phydev->drv->config(phydev);
 297
 298         return 0;
 299 }
 300
 301 /* On Cuboxi Ethernet PHY can be located at addresses 0x0 or 0x4 */
 302 #define ETH_PHY_MASK    ((1 << 0x0) | (1 << 0x4))
 303
 304 int board_eth_init(bd_t *bis)
 305 {
 306         struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
 307         struct mii_dev *bus;
 308         struct phy_device *phydev;
 309
 310         int ret = enable_fec_anatop_clock(0, ENET_25MHZ);
 311         if (ret)
 312                 return ret;
 313
 314         /* set gpr1[ENET_CLK_SEL] */
 315         setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
 316
 317         setup_iomux_enet();
 318
 319         bus = fec_get_miibus(IMX_FEC_BASE, -1);
 320         if (!bus)
 321                 return -EINVAL;
 322
 323         phydev = phy_find_by_mask(bus, ETH_PHY_MASK, PHY_INTERFACE_MODE_RGMII);
 324         if (!phydev) {
 325                 ret = -EINVAL;
 326                 goto free_bus;
 327         }
 328
 329         debug("using phy at address %d\n", phydev->addr);
 330         ret = fec_probe(bis, -1, IMX_FEC_BASE, bus, phydev);
 331         if (ret)
 332                 goto free_phydev;
 333
 334         return 0;
 335
 336 free_phydev:
 337         free(phydev);
 338 free_bus:
 339         free(bus);
 340         return ret;
 341 }
 342
 343 #ifdef CONFIG_VIDEO_IPUV3
 344 static void do_enable_hdmi(struct display_info_t const *dev)
 345 {
 346         imx_enable_hdmi_phy();
 347 }
 348
 349 struct display_info_t const displays[] = {
 350         {
 351                 .bus    = -1,
 352                 .addr   = 0,
 353                 .pixfmt = IPU_PIX_FMT_RGB24,
 354                 .detect = detect_hdmi,
 355                 .enable = do_enable_hdmi,
 356                 .mode   = {
 357                         .name           = "HDMI",
 358                         /* 1024x768@60Hz (VESA)*/
 359                         .refresh        = 60,
 360                         .xres           = 1024,
 361                         .yres           = 768,
 362                         .pixclock       = 15384,
 363                         .left_margin    = 160,
 364                         .right_margin   = 24,
 365                         .upper_margin   = 29,
 366                         .lower_margin   = 3,
 367                         .hsync_len      = 136,
 368                         .vsync_len      = 6,
 369                         .sync           = FB_SYNC_EXT,
 370                         .vmode          = FB_VMODE_NONINTERLACED
 371                 }
 372         }
 373 };
 374
 375 size_t display_count = ARRAY_SIZE(displays);
 376
 377 static int setup_display(void)
 378 {
 379         struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 380         int reg;
 381         int timeout = 100000;
 382
 383         enable_ipu_clock();
 384         imx_setup_hdmi();
 385
 386         /* set video pll to 455MHz (24MHz * (37+11/12) / 2) */
 387         setbits_le32(&ccm->analog_pll_video, BM_ANADIG_PLL_VIDEO_POWERDOWN);
 388
 389         reg = readl(&ccm->analog_pll_video);
 390         reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
 391         reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(37);
 392         reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
 393         reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(1);
 394         writel(reg, &ccm->analog_pll_video);
 395
 396         writel(BF_ANADIG_PLL_VIDEO_NUM_A(11), &ccm->analog_pll_video_num);
 397         writel(BF_ANADIG_PLL_VIDEO_DENOM_B(12), &ccm->analog_pll_video_denom);
 398
 399         reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
 400         writel(reg, &ccm->analog_pll_video);
 401
 402         while (timeout--)
 403                 if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
 404                         break;
 405         if (timeout < 0) {
 406                 printf("Warning: video pll lock timeout!\n");
 407                 return -ETIMEDOUT;
 408         }
 409
 410         reg = readl(&ccm->analog_pll_video);
 411         reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
 412         reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
 413         writel(reg, &ccm->analog_pll_video);
 414
 415         /* gate ipu1_di0_clk */
 416         clrbits_le32(&ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
 417
 418         /* select video_pll clock / 7  for ipu1_di0_clk -> 65MHz pixclock */
 419         reg = readl(&ccm->chsccdr);
 420         reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK |
 421                  MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK |
 422                  MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
 423         reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET) |
 424                (6 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET) |
 425                (0 << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
 426         writel(reg, &ccm->chsccdr);
 427
 428         /* enable ipu1_di0_clk */
 429         setbits_le32(&ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK);
 430
 431         return 0;
 432 }
 433 #endif /* CONFIG_VIDEO_IPUV3 */
 434
 435 #ifdef CONFIG_USB_EHCI_MX6
 436 static void setup_usb(void)
 437 {
 438         SETUP_IOMUX_PADS(usb_pads);
 439 }
 440
 441 int board_ehci_hcd_init(int port)
 442 {
 443         if (port == 1)
 444                 gpio_direction_output(USB_H1_VBUS, 1);
 445
 446         return 0;
 447 }
 448 #endif
 449
 450 int board_early_init_f(void)
 451 {
 452         setup_iomux_uart();
 453
 454 #ifdef CONFIG_CMD_SATA
 455         setup_sata();
 456 #endif
 457
 458 #ifdef CONFIG_USB_EHCI_MX6
 459         setup_usb();
 460 #endif
 461         return 0;
 462 }
 463
 464 int board_init(void)
 465 {
 466         int ret = 0;
 467
 468         /* address of boot parameters */
 469         gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 470
 471 #ifdef CONFIG_VIDEO_IPUV3
 472         ret = setup_display();
 473 #endif
 474
 475         return ret;
 476 }
 477
 478 static enum board_type board_type(void)
 479 {
 480         int val1, val2, val3;
 481
 482         SETUP_IOMUX_PADS(board_detect);
 483
 484         /*
 485          * Machine selection -
 486          * Machine      val1, val2, val3
 487          * ----------------------------
 488          * HB2            x     x    0
 489          * HB rev 3.x     x     0    x
 490          * CBi            0     1    x
 491          * HB             1     1    x
 492          */
 493
 494         gpio_direction_input(IMX_GPIO_NR(2, 8));
 495         val3 = gpio_get_value(IMX_GPIO_NR(2, 8));
 496
 497         if (val3 == 0)
 498                 return HUMMINGBOARD2;
 499
 500         gpio_direction_input(IMX_GPIO_NR(3, 4));
 501         val2 = gpio_get_value(IMX_GPIO_NR(3, 4));
 502
 503         if (val2 == 0)
 504                 return HUMMINGBOARD;
 505
 506         gpio_direction_input(IMX_GPIO_NR(4, 9));
 507         val1 = gpio_get_value(IMX_GPIO_NR(4, 9));
 508
 509         if (val1 == 0) {
 510                 return CUBOXI;
 511         } else {
 512                 return HUMMINGBOARD;
 513         }
 514 }
 515
 516 static bool is_rev_15_som(void)
 517 {
 518         int val1, val2;
 519         SETUP_IOMUX_PADS(som_rev_detect);
 520
 521         val1 = gpio_get_value(IMX_GPIO_NR(6, 0));
 522         val2 = gpio_get_value(IMX_GPIO_NR(6, 4));
 523
 524         if (val1 == 1 && val2 == 0)
 525                 return true;
 526
 527         return false;
 528 }
 529
 530 static bool has_emmc(void)
 531 {
 532         struct mmc *mmc;
 533         mmc = find_mmc_device(1);
 534         if (!mmc)
 535                 return 0;
 536         return (mmc_get_op_cond(mmc) < 0) ? 0 : 1;
 537 }
 538
 539 int checkboard(void)
 540 {
 541         switch (board_type()) {
 542         case CUBOXI:
 543                 puts("Board: MX6 Cubox-i");
 544                 break;
 545         case HUMMINGBOARD:
 546                 puts("Board: MX6 HummingBoard");
 547                 break;
 548         case HUMMINGBOARD2:
 549                 puts("Board: MX6 HummingBoard2");
 550                 break;
 551         case UNKNOWN:
 552         default:
 553                 puts("Board: Unknown\n");
 554                 goto out;
 555         }
 556
 557         if (is_rev_15_som())
 558                 puts(" (som rev 1.5)\n");
 559         else
 560                 puts("\n");
 561
 562 out:
 563         return 0;
 564 }
 565
 566 int board_late_init(void)
 567 {
 568 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
 569         switch (board_type()) {
 570         case CUBOXI:
 571                 env_set("board_name", "CUBOXI");
 572                 break;
 573         case HUMMINGBOARD:
 574                 env_set("board_name", "HUMMINGBOARD");
 575                 break;
 576         case HUMMINGBOARD2:
 577                 env_set("board_name", "HUMMINGBOARD2");
 578                 break;
 579         case UNKNOWN:
 580         default:
 581                 env_set("board_name", "CUBOXI");
 582         }
 583
 584         if (is_mx6dq())
 585                 env_set("board_rev", "MX6Q");
 586         else
 587                 env_set("board_rev", "MX6DL");
 588
 589         if (is_rev_15_som())
 590                 env_set("som_rev", "V15");
 591
 592         if (has_emmc())
 593                 env_set("has_emmc", "yes");
 594
 595 #endif
 596
 597         return 0;
 598 }
 599
 600 #ifdef CONFIG_SPL_BUILD
 601 #include <asm/arch/mx6-ddr.h>
 602 static const struct mx6dq_iomux_ddr_regs mx6q_ddr_ioregs = {
 603         .dram_sdclk_0 =  0x00020030,
 604         .dram_sdclk_1 =  0x00020030,
 605         .dram_cas =  0x00020030,
 606         .dram_ras =  0x00020030,
 607         .dram_reset =  0x000c0030,
 608         .dram_sdcke0 =  0x00003000,
 609         .dram_sdcke1 =  0x00003000,
 610         .dram_sdba2 =  0x00000000,
 611         .dram_sdodt0 =  0x00003030,
 612         .dram_sdodt1 =  0x00003030,
 613         .dram_sdqs0 =  0x00000030,
 614         .dram_sdqs1 =  0x00000030,
 615         .dram_sdqs2 =  0x00000030,
 616         .dram_sdqs3 =  0x00000030,
 617         .dram_sdqs4 =  0x00000030,
 618         .dram_sdqs5 =  0x00000030,
 619         .dram_sdqs6 =  0x00000030,
 620         .dram_sdqs7 =  0x00000030,
 621         .dram_dqm0 =  0x00020030,
 622         .dram_dqm1 =  0x00020030,
 623         .dram_dqm2 =  0x00020030,
 624         .dram_dqm3 =  0x00020030,
 625         .dram_dqm4 =  0x00020030,
 626         .dram_dqm5 =  0x00020030,
 627         .dram_dqm6 =  0x00020030,
 628         .dram_dqm7 =  0x00020030,
 629 };
 630
 631 static const struct mx6sdl_iomux_ddr_regs mx6dl_ddr_ioregs = {
 632         .dram_sdclk_0 = 0x00000028,
 633         .dram_sdclk_1 = 0x00000028,
 634         .dram_cas =     0x00000028,
 635         .dram_ras =     0x00000028,
 636         .dram_reset =   0x000c0028,
 637         .dram_sdcke0 =  0x00003000,
 638         .dram_sdcke1 =  0x00003000,
 639         .dram_sdba2 =   0x00000000,
 640         .dram_sdodt0 =  0x00003030,
 641         .dram_sdodt1 =  0x00003030,
 642         .dram_sdqs0 =   0x00000028,
 643         .dram_sdqs1 =   0x00000028,
 644         .dram_sdqs2 =   0x00000028,
 645         .dram_sdqs3 =   0x00000028,
 646         .dram_sdqs4 =   0x00000028,
 647         .dram_sdqs5 =   0x00000028,
 648         .dram_sdqs6 =   0x00000028,
 649         .dram_sdqs7 =   0x00000028,
 650         .dram_dqm0 =    0x00000028,
 651         .dram_dqm1 =    0x00000028,
 652         .dram_dqm2 =    0x00000028,
 653         .dram_dqm3 =    0x00000028,
 654         .dram_dqm4 =    0x00000028,
 655         .dram_dqm5 =    0x00000028,
 656         .dram_dqm6 =    0x00000028,
 657         .dram_dqm7 =    0x00000028,
 658 };
 659
 660 static const struct mx6dq_iomux_grp_regs mx6q_grp_ioregs = {
 661         .grp_ddr_type =  0x000C0000,
 662         .grp_ddrmode_ctl =  0x00020000,
 663         .grp_ddrpke =  0x00000000,
 664         .grp_addds =  0x00000030,
 665         .grp_ctlds =  0x00000030,
 666         .grp_ddrmode =  0x00020000,
 667         .grp_b0ds =  0x00000030,
 668         .grp_b1ds =  0x00000030,
 669         .grp_b2ds =  0x00000030,
 670         .grp_b3ds =  0x00000030,
 671         .grp_b4ds =  0x00000030,
 672         .grp_b5ds =  0x00000030,
 673         .grp_b6ds =  0x00000030,
 674         .grp_b7ds =  0x00000030,
 675 };
 676
 677 static const struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
 678         .grp_ddr_type = 0x000c0000,
 679         .grp_ddrmode_ctl = 0x00020000,
 680         .grp_ddrpke = 0x00000000,
 681         .grp_addds = 0x00000028,
 682         .grp_ctlds = 0x00000028,
 683         .grp_ddrmode = 0x00020000,
 684         .grp_b0ds = 0x00000028,
 685         .grp_b1ds = 0x00000028,
 686         .grp_b2ds = 0x00000028,
 687         .grp_b3ds = 0x00000028,
 688         .grp_b4ds = 0x00000028,
 689         .grp_b5ds = 0x00000028,
 690         .grp_b6ds = 0x00000028,
 691         .grp_b7ds = 0x00000028,
 692 };
 693
 694 /* microSOM with Dual processor and 1GB memory */
 695 static const struct mx6_mmdc_calibration mx6q_1g_mmcd_calib = {
 696         .p0_mpwldectrl0 =  0x00000000,
 697         .p0_mpwldectrl1 =  0x00000000,
 698         .p1_mpwldectrl0 =  0x00000000,
 699         .p1_mpwldectrl1 =  0x00000000,
 700         .p0_mpdgctrl0 =    0x0314031c,
 701         .p0_mpdgctrl1 =    0x023e0304,
 702         .p1_mpdgctrl0 =    0x03240330,
 703         .p1_mpdgctrl1 =    0x03180260,
 704         .p0_mprddlctl =    0x3630323c,
 705         .p1_mprddlctl =    0x3436283a,
 706         .p0_mpwrdlctl =    0x36344038,
 707         .p1_mpwrdlctl =    0x422a423c,
 708 };
 709
 710 /* microSOM with Quad processor and 2GB memory */
 711 static const struct mx6_mmdc_calibration mx6q_2g_mmcd_calib = {
 712         .p0_mpwldectrl0 =  0x00000000,
 713         .p0_mpwldectrl1 =  0x00000000,
 714         .p1_mpwldectrl0 =  0x00000000,
 715         .p1_mpwldectrl1 =  0x00000000,
 716         .p0_mpdgctrl0 =    0x0314031c,
 717         .p0_mpdgctrl1 =    0x023e0304,
 718         .p1_mpdgctrl0 =    0x03240330,
 719         .p1_mpdgctrl1 =    0x03180260,
 720         .p0_mprddlctl =    0x3630323c,
 721         .p1_mprddlctl =    0x3436283a,
 722         .p0_mpwrdlctl =    0x36344038,
 723         .p1_mpwrdlctl =    0x422a423c,
 724 };
 725
 726 /* microSOM with Solo processor and 512MB memory */
 727 static const struct mx6_mmdc_calibration mx6dl_512m_mmcd_calib = {
 728         .p0_mpwldectrl0 = 0x0045004D,
 729         .p0_mpwldectrl1 = 0x003A0047,
 730         .p0_mpdgctrl0 =   0x023C0224,
 731         .p0_mpdgctrl1 =   0x02000220,
 732         .p0_mprddlctl =   0x44444846,
 733         .p0_mpwrdlctl =   0x32343032,
 734 };
 735
 736 /* microSOM with Dual lite processor and 1GB memory */
 737 static const struct mx6_mmdc_calibration mx6dl_1g_mmcd_calib = {
 738         .p0_mpwldectrl0 =  0x0045004D,
 739         .p0_mpwldectrl1 =  0x003A0047,
 740         .p1_mpwldectrl0 =  0x001F001F,
 741         .p1_mpwldectrl1 =  0x00210035,
 742         .p0_mpdgctrl0 =    0x023C0224,
 743         .p0_mpdgctrl1 =    0x02000220,
 744         .p1_mpdgctrl0 =    0x02200220,
 745         .p1_mpdgctrl1 =    0x02040208,
 746         .p0_mprddlctl =    0x44444846,
 747         .p1_mprddlctl =    0x4042463C,
 748         .p0_mpwrdlctl =    0x32343032,
 749         .p1_mpwrdlctl =    0x36363430,
 750 };
 751
 752 static struct mx6_ddr3_cfg mem_ddr_2g = {
 753         .mem_speed = 1600,
 754         .density   = 2,
 755         .width     = 16,
 756         .banks     = 8,
 757         .rowaddr   = 14,
 758         .coladdr   = 10,
 759         .pagesz    = 2,
 760         .trcd      = 1375,
 761         .trcmin    = 4875,
 762         .trasmin   = 3500,
 763 };
 764
 765 static struct mx6_ddr3_cfg mem_ddr_4g = {
 766         .mem_speed = 1600,
 767         .density = 4,
 768         .width = 16,
 769         .banks = 8,
 770         .rowaddr = 16,
 771         .coladdr = 10,
 772         .pagesz = 2,
 773         .trcd = 1375,
 774         .trcmin = 4875,
 775         .trasmin = 3500,
 776 };
 777
 778 static void ccgr_init(void)
 779 {
 780         struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 781
 782         writel(0x00C03F3F, &ccm->CCGR0);
 783         writel(0x0030FC03, &ccm->CCGR1);
 784         writel(0x0FFFC000, &ccm->CCGR2);
 785         writel(0x3FF00000, &ccm->CCGR3);
 786         writel(0x00FFF300, &ccm->CCGR4);
 787         writel(0x0F0000C3, &ccm->CCGR5);
 788         writel(0x000003FF, &ccm->CCGR6);
 789 }
 790
 791 static void spl_dram_init(int width)
 792 {
 793         struct mx6_ddr_sysinfo sysinfo = {
 794                 /* width of data bus: 0=16, 1=32, 2=64 */
 795                 .dsize = width / 32,
 796                 /* config for full 4GB range so that get_mem_size() works */
 797                 .cs_density = 32,       /* 32Gb per CS */
 798                 .ncs = 1,               /* single chip select */
 799                 .cs1_mirror = 0,
 800                 .rtt_wr = 1 /*DDR3_RTT_60_OHM*/,        /* RTT_Wr = RZQ/4 */
 801                 .rtt_nom = 1 /*DDR3_RTT_60_OHM*/,       /* RTT_Nom = RZQ/4 */
 802                 .walat = 1,     /* Write additional latency */
 803                 .ralat = 5,     /* Read additional latency */
 804                 .mif3_mode = 3, /* Command prediction working mode */
 805                 .bi_on = 1,     /* Bank interleaving enabled */
 806                 .sde_to_rst = 0x10,     /* 14 cycles, 200us (JEDEC default) */
 807                 .rst_to_cke = 0x23,     /* 33 cycles, 500us (JEDEC default) */
 808                 .ddr_type = DDR_TYPE_DDR3,
 809                 .refsel = 1,    /* Refresh cycles at 32KHz */
 810                 .refr = 7,      /* 8 refresh commands per refresh cycle */
 811         };
 812
 813         if (is_mx6dq())
 814                 mx6dq_dram_iocfg(width, &mx6q_ddr_ioregs, &mx6q_grp_ioregs);
 815         else
 816                 mx6sdl_dram_iocfg(width, &mx6dl_ddr_ioregs, &mx6sdl_grp_ioregs);
 817
 818         if (is_cpu_type(MXC_CPU_MX6D))
 819                 mx6_dram_cfg(&sysinfo, &mx6q_1g_mmcd_calib, &mem_ddr_2g);
 820         else if (is_cpu_type(MXC_CPU_MX6Q))
 821                 mx6_dram_cfg(&sysinfo, &mx6q_2g_mmcd_calib, &mem_ddr_4g);
 822         else if (is_cpu_type(MXC_CPU_MX6DL))
 823                 mx6_dram_cfg(&sysinfo, &mx6dl_1g_mmcd_calib, &mem_ddr_2g);
 824         else if (is_cpu_type(MXC_CPU_MX6SOLO))
 825                 mx6_dram_cfg(&sysinfo, &mx6dl_512m_mmcd_calib, &mem_ddr_2g);
 826 }
 827
 828 void board_init_f(ulong dummy)
 829 {
 830         /* setup AIPS and disable watchdog */
 831         arch_cpu_init();
 832
 833         ccgr_init();
 834         gpr_init();
 835
 836         /* iomux and setup of i2c */
 837         board_early_init_f();
 838
 839         /* setup GP timer */
 840         timer_init();
 841
 842         /* UART clocks enabled and gd valid - init serial console */
 843         preloader_console_init();
 844
 845         /* DDR initialization */
 846         if (is_cpu_type(MXC_CPU_MX6SOLO))
 847                 spl_dram_init(32);
 848         else
 849                 spl_dram_init(64);
 850
 851         /* Clear the BSS. */
 852         memset(__bss_start, 0, __bss_end - __bss_start);
 853
 854         /* load/boot image from boot device */
 855         board_init_r(NULL, 0);
 856 }
 857 #endif