board/ronetix/pm9g45/pm9g45.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * (C) Copyright 2010
   4  * Ilko Iliev <iliev@ronetix.at>
   5  * Asen Dimov <dimov@ronetix.at>
   6  * Ronetix GmbH <www.ronetix.at>
   7  *
   8  * (C) Copyright 2007-2008
   9  * Stelian Pop <stelian@popies.net>
  10  * Lead Tech Design <www.leadtechdesign.com>
  11  */
  12
  13 #include <common.h>
  14 #include <linux/sizes.h>
  15 #include <asm/io.h>
  16 #include <asm/gpio.h>
  17 #include <asm/arch/at91sam9_smc.h>
  18 #include <asm/arch/at91_common.h>
  19 #include <asm/arch/at91_rstc.h>
  20 #include <asm/arch/at91_matrix.h>
  21 #include <asm/arch/gpio.h>
  22 #include <asm/arch/clk.h>
  23 #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
  24 #include <net.h>
  25 #endif
  26 #include <netdev.h>
  27 #include <asm/mach-types.h>
  28
  29 DECLARE_GLOBAL_DATA_PTR;
  30
  31 /*
  32  * Miscelaneous platform dependent initialisations
  33  */
  34
  35 #ifdef CONFIG_CMD_NAND
  36 static void pm9g45_nand_hw_init(void)
  37 {
  38         unsigned long csa;
  39         struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
  40         struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
  41
  42         /* Enable CS3 */
  43         csa = readl(&matrix->ccr[6]) | AT91_MATRIX_CSA_EBI_CS3A;
  44         writel(csa, &matrix->ccr[6]);
  45
  46         /* Configure SMC CS3 for NAND/SmartMedia */
  47         writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
  48                 AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
  49                 &smc->cs[3].setup);
  50
  51         writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(3) |
  52                 AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(2),
  53                 &smc->cs[3].pulse);
  54
  55         writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(4),
  56                 &smc->cs[3].cycle);
  57
  58         writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
  59                 AT91_SMC_MODE_EXNW_DISABLE |
  60                 AT91_SMC_MODE_DBW_8 |
  61                 AT91_SMC_MODE_TDF_CYCLE(3),
  62                 &smc->cs[3].mode);
  63
  64         at91_periph_clk_enable(ATMEL_ID_PIOC);
  65
  66 #ifdef CONFIG_SYS_NAND_READY_PIN
  67         /* Configure RDY/BSY */
  68         gpio_direction_input(CONFIG_SYS_NAND_READY_PIN);
  69 #endif
  70
  71         /* Enable NandFlash */
  72         gpio_direction_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
  73 }
  74 #endif
  75
  76 #ifdef CONFIG_MACB
  77 static void pm9g45_macb_hw_init(void)
  78 {
  79         /*
  80          * PD2 enables the 50MHz oscillator for Ethernet PHY
  81          * 1 - enable
  82          * 0 - disable
  83          */
  84         at91_set_pio_output(AT91_PIO_PORTD, 2, 1);
  85         at91_set_pio_value(AT91_PIO_PORTD, 2, 1); /* 1- enable, 0 - disable */
  86
  87         at91_periph_clk_enable(ATMEL_ID_EMAC);
  88
  89         /*
  90          * Disable pull-up on:
  91          *      RXDV (PA15) => PHY normal mode (not Test mode)
  92          *      ERX0 (PA12) => PHY ADDR0
  93          *      ERX1 (PA13) => PHY ADDR1 => PHYADDR = 0x0
  94          *
  95          * PHY has internal pull-down
  96          */
  97         at91_set_pio_pullup(AT91_PIO_PORTA, 15, 0);
  98         at91_set_pio_pullup(AT91_PIO_PORTA, 12, 0);
  99         at91_set_pio_pullup(AT91_PIO_PORTA, 13, 0);
 100
 101         /* Re-enable pull-up */
 102         at91_set_pio_pullup(AT91_PIO_PORTA, 15, 1);
 103         at91_set_pio_pullup(AT91_PIO_PORTA, 12, 1);
 104         at91_set_pio_pullup(AT91_PIO_PORTA, 13, 1);
 105
 106         at91_macb_hw_init();
 107 }
 108 #endif
 109
 110 int board_early_init_f(void)
 111 {
 112         at91_periph_clk_enable(ATMEL_ID_PIOA);
 113         at91_periph_clk_enable(ATMEL_ID_PIOB);
 114         at91_periph_clk_enable(ATMEL_ID_PIOC);
 115         at91_periph_clk_enable(ATMEL_ID_PIODE);
 116
 117         at91_seriald_hw_init();
 118
 119         return 0;
 120 }
 121
 122 int board_init(void)
 123 {
 124         /* arch number of AT91SAM9M10G45EK-Board */
 125         gd->bd->bi_arch_number = MACH_TYPE_PM9G45;
 126         /* adress of boot parameters */
 127         gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 128
 129 #ifdef CONFIG_CMD_NAND
 130         pm9g45_nand_hw_init();
 131 #endif
 132
 133 #ifdef CONFIG_MACB
 134         pm9g45_macb_hw_init();
 135 #endif
 136         return 0;
 137 }
 138
 139 int dram_init(void)
 140 {
 141         /* dram_init must store complete ramsize in gd->ram_size */
 142         gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
 143                                     CONFIG_SYS_SDRAM_SIZE);
 144         return 0;
 145 }
 146
 147 int dram_init_banksize(void)
 148 {
 149         gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
 150         gd->bd->bi_dram[0].size = CONFIG_SYS_SDRAM_SIZE;
 151
 152         return 0;
 153 }
 154
 155 #ifdef CONFIG_RESET_PHY_R
 156 void reset_phy(void)
 157 {
 158 #ifdef CONFIG_MACB
 159         /*
 160          * Initialize ethernet HW addr prior to starting Linux,
 161          * needed for nfsroot
 162          */
 163         eth_init();
 164 #endif
 165 }
 166 #endif
 167
 168 int board_eth_init(bd_t *bis)
 169 {
 170         int rc = 0;
 171 #ifdef CONFIG_MACB
 172         rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x01);
 173 #endif
 174         return rc;
 175 }