board/freescale/ls1012ardb/eth.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * Copyright 2015-2016 Freescale Semiconductor, Inc.
   4  * Copyright 2017 NXP
   5  */
   6
   7 #include <common.h>
   8 #include <dm.h>
   9 #include <net.h>
  10 #include <asm/io.h>
  11 #include <netdev.h>
  12 #include <fm_eth.h>
  13 #include <fsl_mdio.h>
  14 #include <malloc.h>
  15 #include <asm/types.h>
  16 #include <fsl_dtsec.h>
  17 #include <asm/arch/soc.h>
  18 #include <asm/arch-fsl-layerscape/config.h>
  19 #include <asm/arch-fsl-layerscape/immap_lsch2.h>
  20 #include <asm/arch/fsl_serdes.h>
  21 #include <linux/delay.h>
  22 #include <net/pfe_eth/pfe_eth.h>
  23 #include <dm/platform_data/pfe_dm_eth.h>
  24 #include <i2c.h>
  25
  26 #define DEFAULT_PFE_MDIO_NAME "PFE_MDIO"
  27
  28 static inline void ls1012ardb_reset_phy(void)
  29 {
  30 #ifdef CONFIG_TARGET_LS1012ARDB
  31         /* Through reset IO expander reset both RGMII and SGMII PHYs */
  32 #ifdef CONFIG_DM_I2C
  33         struct udevice *dev;
  34         int ret;
  35
  36         /*
  37          * The I2C IO-expander PCAL9555A is mouted on I2C1 bus(bus number is 0).
  38          */
  39         ret = i2c_get_chip_for_busnum(0, I2C_MUX_IO2_ADDR,
  40                                       1, &dev);
  41         if (ret) {
  42                 printf("%s: Cannot find udev for a bus %d\n", __func__,
  43                        0);
  44                 return;
  45         }
  46         /* Config port 0
  47          * - config pin IOXP_RST_ETH1_B and IOXP_RST_ETH2_B
  48          *   are enabled as an output.
  49          */
  50         dm_i2c_reg_write(dev, 6, __PHY_MASK);
  51
  52         /*
  53          * Set port 0 output a value to reset ETH2 interface
  54          * - pin IOXP_RST_ETH2_B output 0b0
  55          */
  56         dm_i2c_reg_write(dev, 2, __PHY_ETH2_MASK);
  57         mdelay(10);
  58         dm_i2c_reg_write(dev, 2, __PHY_ETH1_MASK);
  59         /*
  60          * Set port 0 output a value to reset ETH1 interface
  61          * - pin IOXP_RST_ETH1_B output 0b0
  62          */
  63         mdelay(10);
  64         dm_i2c_reg_write(dev, 2, 0xFF);
  65 #else
  66         i2c_reg_write(I2C_MUX_IO2_ADDR, 6, __PHY_MASK);
  67         i2c_reg_write(I2C_MUX_IO2_ADDR, 2, __PHY_ETH2_MASK);
  68         mdelay(10);
  69         i2c_reg_write(I2C_MUX_IO2_ADDR, 2, __PHY_ETH1_MASK);
  70         mdelay(10);
  71         i2c_reg_write(I2C_MUX_IO2_ADDR, 2, 0xFF);
  72 #endif
  73         mdelay(50);
  74 #endif
  75 }
  76
  77 int pfe_eth_board_init(struct udevice *dev)
  78 {
  79         static int init_done;
  80         struct mii_dev *bus;
  81         struct pfe_mdio_info mac_mdio_info;
  82         struct pfe_eth_dev *priv = dev_get_priv(dev);
  83         struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
  84
  85         int srds_s1 = in_be32(&gur->rcwsr[4]) &
  86                         FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
  87         srds_s1 >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
  88
  89         if (!init_done) {
  90                 ls1012ardb_reset_phy();
  91                 mac_mdio_info.reg_base = (void *)EMAC1_BASE_ADDR;
  92                 mac_mdio_info.name = DEFAULT_PFE_MDIO_NAME;
  93
  94                 bus = pfe_mdio_init(&mac_mdio_info);
  95                 if (!bus) {
  96                         printf("Failed to register mdio\n");
  97                         return -1;
  98                 }
  99                 init_done = 1;
 100         }
 101
 102         pfe_set_mdio(priv->gemac_port,
 103                      miiphy_get_dev_by_name(DEFAULT_PFE_MDIO_NAME));
 104
 105         switch (srds_s1) {
 106         case 0x3508:
 107                 if (!priv->gemac_port) {
 108                         /* MAC1 */
 109                         pfe_set_phy_address_mode(priv->gemac_port,
 110                                                  CONFIG_PFE_EMAC1_PHY_ADDR,
 111                                                  PHY_INTERFACE_MODE_SGMII);
 112                 } else {
 113                         /* MAC2 */
 114                         pfe_set_phy_address_mode(priv->gemac_port,
 115                                                  CONFIG_PFE_EMAC2_PHY_ADDR,
 116                                                  PHY_INTERFACE_MODE_RGMII_TXID);
 117                 }
 118                 break;
 119         case 0x2208:
 120                 if (!priv->gemac_port) {
 121                         /* MAC1 */
 122                         pfe_set_phy_address_mode(priv->gemac_port,
 123                                                  CONFIG_PFE_EMAC1_PHY_ADDR,
 124                                                  PHY_INTERFACE_MODE_SGMII_2500);
 125                 } else {
 126                         /* MAC2 */
 127                         pfe_set_phy_address_mode(priv->gemac_port,
 128                                                  CONFIG_PFE_EMAC2_PHY_ADDR,
 129                                                  PHY_INTERFACE_MODE_SGMII_2500);
 130                 }
 131                 break;
 132         default:
 133                 printf("unsupported SerDes PRCTL= %d\n", srds_s1);
 134                 break;
 135         }
 136         return 0;
 137 }
 138
 139 static struct pfe_eth_pdata pfe_pdata0 = {
 140         .pfe_eth_pdata_mac = {
 141                 .iobase = (phys_addr_t)EMAC1_BASE_ADDR,
 142                 .phy_interface = 0,
 143         },
 144
 145         .pfe_ddr_addr = {
 146                 .ddr_pfe_baseaddr = (void *)CONFIG_DDR_PFE_BASEADDR,
 147                 .ddr_pfe_phys_baseaddr = CONFIG_DDR_PFE_PHYS_BASEADDR,
 148         },
 149 };
 150
 151 static struct pfe_eth_pdata pfe_pdata1 = {
 152         .pfe_eth_pdata_mac = {
 153                 .iobase = (phys_addr_t)EMAC2_BASE_ADDR,
 154                 .phy_interface = 1,
 155         },
 156
 157         .pfe_ddr_addr = {
 158                 .ddr_pfe_baseaddr = (void *)CONFIG_DDR_PFE_BASEADDR,
 159                 .ddr_pfe_phys_baseaddr = CONFIG_DDR_PFE_PHYS_BASEADDR,
 160         },
 161 };
 162
 163 U_BOOT_DEVICE(ls1012a_pfe0) = {
 164         .name = "pfe_eth",
 165         .platdata = &pfe_pdata0,
 166 };
 167
 168 U_BOOT_DEVICE(ls1012a_pfe1) = {
 169         .name = "pfe_eth",
 170         .platdata = &pfe_pdata1,
 171 };