board/el/el6x/el6x.c

   1 /*
   2  * Copyright (C) Stefano Babic <sbabic@denx.de>
   3  *
   4  * Based on other i.MX6 boards
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 #include <asm/arch/clock.h>
  10 #include <asm/arch/imx-regs.h>
  11 #include <asm/arch/iomux.h>
  12 #include <asm/arch/mx6-pins.h>
  13 #include <linux/errno.h>
  14 #include <asm/gpio.h>
  15 #include <asm/mach-imx/mxc_i2c.h>
  16 #include <asm/mach-imx/iomux-v3.h>
  17 #include <asm/mach-imx/boot_mode.h>
  18 #include <asm/mach-imx/video.h>
  19 #include <mmc.h>
  20 #include <fsl_esdhc.h>
  21 #include <miiphy.h>
  22 #include <netdev.h>
  23 #include <asm/arch/mxc_hdmi.h>
  24 #include <asm/arch/crm_regs.h>
  25 #include <asm/io.h>
  26 #include <asm/arch/sys_proto.h>
  27 #include <i2c.h>
  28 #include <power/pmic.h>
  29 #include <power/pfuze100_pmic.h>
  30 #include <asm/arch/mx6-ddr.h>
  31
  32 DECLARE_GLOBAL_DATA_PTR;
  33
  34 #define OPEN_PAD_CTRL  (PAD_CTL_ODE  | PAD_CTL_DSE_DISABLE | (0 << 12))
  35
  36 #define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |                   \
  37         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |                 \
  38         PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  39
  40 #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |                    \
  41         PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |                 \
  42         PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  43
  44 #define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |                   \
  45         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
  46
  47 #define ENET_PAD_CTRL_PD  (PAD_CTL_PUS_100K_DOWN |              \
  48         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
  49
  50 #define ENET_PAD_CTRL_CLK  ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \
  51         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
  52
  53 #define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
  54         PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
  55
  56 #define I2C_PAD_CTRL  (PAD_CTL_PUS_100K_UP |                    \
  57         PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |   \
  58         PAD_CTL_ODE | PAD_CTL_SRE_FAST)
  59
  60 #define I2C_PMIC        1
  61
  62 #define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
  63
  64 #define ETH_PHY_RESET   IMX_GPIO_NR(2, 4)
  65
  66 int dram_init(void)
  67 {
  68         gd->ram_size = imx_ddr_size();
  69
  70         return 0;
  71 }
  72
  73 iomux_v3_cfg_t const uart2_pads[] = {
  74         MX6_PAD_SD3_DAT5__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
  75         MX6_PAD_SD3_DAT4__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
  76 };
  77
  78 static void setup_iomux_uart(void)
  79 {
  80         imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads));
  81 }
  82
  83 #ifdef CONFIG_TARGET_ZC5202
  84 iomux_v3_cfg_t const enet_pads[] = {
  85         MX6_PAD_GPIO_18__ENET_RX_CLK            | MUX_PAD_CTRL(ENET_PAD_CTRL),
  86         MX6_PAD_ENET_RXD0__ENET_RX_DATA0        | MUX_PAD_CTRL(ENET_PAD_CTRL),
  87         MX6_PAD_ENET_RXD1__ENET_RX_DATA1        | MUX_PAD_CTRL(ENET_PAD_CTRL),
  88         MX6_PAD_KEY_COL2__ENET_RX_DATA2         | MUX_PAD_CTRL(ENET_PAD_CTRL),
  89         MX6_PAD_KEY_COL0__ENET_RX_DATA3         | MUX_PAD_CTRL(ENET_PAD_CTRL),
  90         MX6_PAD_ENET_CRS_DV__ENET_RX_EN         | MUX_PAD_CTRL(ENET_PAD_CTRL),
  91         MX6_PAD_ENET_REF_CLK__ENET_TX_CLK       | MUX_PAD_CTRL(ENET_PAD_CTRL_CLK),
  92         MX6_PAD_ENET_TXD0__ENET_TX_DATA0        | MUX_PAD_CTRL(ENET_PAD_CTRL),
  93         MX6_PAD_ENET_TXD1__ENET_TX_DATA1        | MUX_PAD_CTRL(ENET_PAD_CTRL),
  94         MX6_PAD_GPIO_19__ENET_TX_ER             | MUX_PAD_CTRL(ENET_PAD_CTRL),
  95         MX6_PAD_KEY_ROW2__ENET_TX_DATA2         | MUX_PAD_CTRL(ENET_PAD_CTRL),
  96         MX6_PAD_KEY_ROW0__ENET_TX_DATA3         | MUX_PAD_CTRL(ENET_PAD_CTRL),
  97         MX6_PAD_ENET_TX_EN__ENET_TX_EN          | MUX_PAD_CTRL(ENET_PAD_CTRL),
  98         MX6_PAD_ENET_RX_ER__ENET_RX_ER          | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
  99         /* Switch Reset */
 100         MX6_PAD_NANDF_D4__GPIO2_IO04            | MUX_PAD_CTRL(ENET_PAD_CTRL_PD),
 101         /* Switch Interrupt */
 102         MX6_PAD_NANDF_D5__GPIO2_IO05            | MUX_PAD_CTRL(NO_PAD_CTRL),
 103         /* use CRS and COL pads as GPIOs */
 104         MX6_PAD_KEY_COL3__GPIO4_IO12            | MUX_PAD_CTRL(OPEN_PAD_CTRL),
 105         MX6_PAD_KEY_ROW1__GPIO4_IO09            | MUX_PAD_CTRL(OPEN_PAD_CTRL),
 106
 107 };
 108
 109 #define BOARD_NAME "EL6x-ZC5202"
 110 #else
 111 iomux_v3_cfg_t const enet_pads[] = {
 112         MX6_PAD_ENET_MDIO__ENET_MDIO    | MUX_PAD_CTRL(ENET_PAD_CTRL),
 113         MX6_PAD_ENET_MDC__ENET_MDC      | MUX_PAD_CTRL(ENET_PAD_CTRL),
 114         MX6_PAD_RGMII_TXC__RGMII_TXC    | MUX_PAD_CTRL(ENET_PAD_CTRL),
 115         MX6_PAD_RGMII_TD0__RGMII_TD0    | MUX_PAD_CTRL(ENET_PAD_CTRL),
 116         MX6_PAD_RGMII_TD1__RGMII_TD1    | MUX_PAD_CTRL(ENET_PAD_CTRL),
 117         MX6_PAD_RGMII_TD2__RGMII_TD2    | MUX_PAD_CTRL(ENET_PAD_CTRL),
 118         MX6_PAD_RGMII_TD3__RGMII_TD3    | MUX_PAD_CTRL(ENET_PAD_CTRL),
 119         MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL      | MUX_PAD_CTRL(ENET_PAD_CTRL),
 120         MX6_PAD_ENET_REF_CLK__ENET_TX_CLK       | MUX_PAD_CTRL(ENET_PAD_CTRL_CLK),
 121         MX6_PAD_RGMII_RXC__RGMII_RXC    | MUX_PAD_CTRL(ENET_PAD_CTRL),
 122         MX6_PAD_RGMII_RD0__RGMII_RD0    | MUX_PAD_CTRL(ENET_PAD_CTRL),
 123         MX6_PAD_RGMII_RD1__RGMII_RD1    | MUX_PAD_CTRL(ENET_PAD_CTRL),
 124         MX6_PAD_RGMII_RD2__RGMII_RD2    | MUX_PAD_CTRL(ENET_PAD_CTRL),
 125         MX6_PAD_RGMII_RD3__RGMII_RD3    | MUX_PAD_CTRL(ENET_PAD_CTRL),
 126         MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL      | MUX_PAD_CTRL(ENET_PAD_CTRL),
 127         MX6_PAD_NANDF_D4__GPIO2_IO04            | MUX_PAD_CTRL(NO_PAD_CTRL),
 128         MX6_PAD_NANDF_D5__GPIO2_IO05            | MUX_PAD_CTRL(NO_PAD_CTRL),
 129 };
 130 #define BOARD_NAME "EL6x-ZC5601"
 131 #endif
 132
 133 static void setup_iomux_enet(void)
 134 {
 135         imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
 136
 137 #ifdef CONFIG_TARGET_ZC5202
 138         /* set CRS and COL to input */
 139         gpio_direction_input(IMX_GPIO_NR(4, 9));
 140         gpio_direction_input(IMX_GPIO_NR(4, 12));
 141
 142         /* Reset Switch */
 143         gpio_direction_output(ETH_PHY_RESET , 0);
 144         mdelay(2);
 145         gpio_set_value(ETH_PHY_RESET, 1);
 146 #endif
 147 }
 148
 149 int board_phy_config(struct phy_device *phydev)
 150 {
 151         if (phydev->drv->config)
 152                 phydev->drv->config(phydev);
 153
 154         return 0;
 155 }
 156
 157 #ifdef CONFIG_MXC_SPI
 158 #ifdef CONFIG_TARGET_ZC5202
 159 iomux_v3_cfg_t const ecspi1_pads[] = {
 160         MX6_PAD_DISP0_DAT20__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
 161         MX6_PAD_DISP0_DAT21__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
 162         MX6_PAD_DISP0_DAT22__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
 163         MX6_PAD_DISP0_DAT23__GPIO5_IO17  | MUX_PAD_CTRL(NO_PAD_CTRL),
 164         MX6_PAD_DISP0_DAT15__GPIO5_IO09  | MUX_PAD_CTRL(NO_PAD_CTRL),
 165 };
 166
 167 iomux_v3_cfg_t const ecspi3_pads[] = {
 168         MX6_PAD_DISP0_DAT0__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
 169         MX6_PAD_DISP0_DAT2__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
 170         MX6_PAD_DISP0_DAT1__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
 171         MX6_PAD_DISP0_DAT7__GPIO4_IO28   | MUX_PAD_CTRL(SPI_PAD_CTRL),
 172         MX6_PAD_DISP0_DAT8__GPIO4_IO29   | MUX_PAD_CTRL(SPI_PAD_CTRL),
 173         MX6_PAD_DISP0_DAT9__GPIO4_IO30   | MUX_PAD_CTRL(SPI_PAD_CTRL),
 174         MX6_PAD_DISP0_DAT10__GPIO4_IO31  | MUX_PAD_CTRL(SPI_PAD_CTRL),
 175 };
 176 #endif
 177
 178 iomux_v3_cfg_t const ecspi4_pads[] = {
 179         MX6_PAD_EIM_D21__ECSPI4_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
 180         MX6_PAD_EIM_D28__ECSPI4_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
 181         MX6_PAD_EIM_D22__ECSPI4_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
 182         MX6_PAD_EIM_D20__GPIO3_IO20  | MUX_PAD_CTRL(NO_PAD_CTRL),
 183 };
 184
 185 int board_spi_cs_gpio(unsigned bus, unsigned cs)
 186 {
 187         return (bus == CONFIG_SF_DEFAULT_BUS && cs == CONFIG_SF_DEFAULT_CS)
 188                 ? (IMX_GPIO_NR(3, 20)) : -1;
 189 }
 190
 191 static void setup_spi(void)
 192 {
 193 #ifdef CONFIG_TARGET_ZC5202
 194         gpio_request(IMX_GPIO_NR(5, 17), "spi_cs0");
 195         gpio_request(IMX_GPIO_NR(5, 9), "spi_cs1");
 196         gpio_direction_output(IMX_GPIO_NR(5, 17), 1);
 197         gpio_direction_output(IMX_GPIO_NR(5, 9), 1);
 198         imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
 199 #endif
 200
 201         gpio_request(IMX_GPIO_NR(3, 20), "spi4_cs0");
 202         gpio_direction_output(IMX_GPIO_NR(3, 20), 1);
 203         imx_iomux_v3_setup_multiple_pads(ecspi4_pads, ARRAY_SIZE(ecspi4_pads));
 204
 205         enable_spi_clk(true, 3);
 206 }
 207 #endif
 208
 209 static struct i2c_pads_info i2c_pad_info1 = {
 210         .scl = {
 211                 .i2c_mode = MX6_PAD_EIM_EB2__I2C2_SCL | I2C_PAD,
 212                 .gpio_mode = MX6_PAD_EIM_EB2__GPIO2_IO30 | I2C_PAD,
 213                 .gp = IMX_GPIO_NR(2, 30)
 214         },
 215         .sda = {
 216                 .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
 217                 .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
 218                 .gp = IMX_GPIO_NR(4, 13)
 219         }
 220 };
 221
 222 static struct i2c_pads_info i2c_pad_info2 = {
 223         .scl = {
 224                 .i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | I2C_PAD,
 225                 .gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 | I2C_PAD,
 226                 .gp = IMX_GPIO_NR(1, 5)
 227         },
 228         .sda = {
 229                 .i2c_mode = MX6_PAD_GPIO_16__I2C3_SDA | I2C_PAD,
 230                 .gpio_mode = MX6_PAD_GPIO_16__GPIO7_IO11 | I2C_PAD,
 231                 .gp = IMX_GPIO_NR(7, 11)
 232         }
 233 };
 234
 235 iomux_v3_cfg_t const usdhc2_pads[] = {
 236         MX6_PAD_SD2_CLK__SD2_CLK        | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 237         MX6_PAD_SD2_CMD__SD2_CMD        | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 238         MX6_PAD_SD2_DAT0__SD2_DATA0     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 239         MX6_PAD_SD2_DAT1__SD2_DATA1     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 240         MX6_PAD_SD2_DAT2__SD2_DATA2     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 241         MX6_PAD_SD2_DAT3__SD2_DATA3     | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 242         MX6_PAD_GPIO_4__SD2_CD_B        | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */
 243 };
 244
 245 iomux_v3_cfg_t const usdhc4_pads[] = {
 246         MX6_PAD_SD4_CLK__SD4_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 247         MX6_PAD_SD4_CMD__SD4_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 248         MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 249         MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 250         MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 251         MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 252         MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 253         MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 254         MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 255         MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 256 };
 257
 258 #ifdef CONFIG_FSL_ESDHC
 259 struct fsl_esdhc_cfg usdhc_cfg[2] = {
 260         {USDHC2_BASE_ADDR},
 261         {USDHC4_BASE_ADDR},
 262 };
 263
 264 #define USDHC2_CD_GPIO  IMX_GPIO_NR(1, 4)
 265
 266 int board_mmc_getcd(struct mmc *mmc)
 267 {
 268         struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
 269         int ret = 0;
 270
 271         switch (cfg->esdhc_base) {
 272         case USDHC2_BASE_ADDR:
 273                 ret = !gpio_get_value(USDHC2_CD_GPIO);
 274                 break;
 275         case USDHC4_BASE_ADDR:
 276                 ret = 1; /* eMMC/uSDHC4 is always present */
 277                 break;
 278         }
 279
 280         return ret;
 281 }
 282
 283 int board_mmc_init(bd_t *bis)
 284 {
 285 #ifndef CONFIG_SPL_BUILD
 286         int ret;
 287         int i;
 288
 289         /*
 290          * According to the board_mmc_init() the following map is done:
 291          * (U-boot device node)    (Physical Port)
 292          * mmc0                    SD2
 293          * mmc1                    SD3
 294          * mmc2                    eMMC
 295          */
 296         for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
 297                 switch (i) {
 298                 case 0:
 299                         imx_iomux_v3_setup_multiple_pads(
 300                                 usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
 301                         gpio_direction_input(USDHC2_CD_GPIO);
 302                         usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
 303                         break;
 304                 case 1:
 305                         imx_iomux_v3_setup_multiple_pads(
 306                                 usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
 307                         usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
 308                         break;
 309                 default:
 310                         printf("Warning: you configured more USDHC controllers"
 311                                "(%d) then supported by the board (%d)\n",
 312                                i + 1, CONFIG_SYS_FSL_USDHC_NUM);
 313                         return -EINVAL;
 314                 }
 315
 316                 ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
 317                 if (ret)
 318                         return ret;
 319         }
 320
 321         return 0;
 322 #else
 323         struct src *psrc = (struct src *)SRC_BASE_ADDR;
 324         unsigned reg = readl(&psrc->sbmr1) >> 11;
 325
 326         /*
 327          * Upon reading BOOT_CFG register the following map is done:
 328          * Bit 11 and 12 of BOOT_CFG register can determine the current
 329          * mmc port
 330          * 0x1                  SD1
 331          * 0x2                  SD2
 332          * 0x3                  SD4
 333          */
 334
 335         switch (reg & 0x3) {
 336         case 0x1:
 337                 imx_iomux_v3_setup_multiple_pads(
 338                         usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
 339                 usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
 340                 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
 341                 gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
 342                 break;
 343         case 0x3:
 344                 imx_iomux_v3_setup_multiple_pads(
 345                         usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
 346                 usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR;
 347                 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
 348                 gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
 349                 break;
 350         }
 351
 352         return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
 353 #endif
 354
 355 }
 356 #endif
 357
 358
 359 /*
 360  * Do not overwrite the console
 361  * Use always serial for U-Boot console
 362  */
 363 int overwrite_console(void)
 364 {
 365         return 1;
 366 }
 367
 368 int board_eth_init(bd_t *bis)
 369 {
 370         setup_iomux_enet();
 371         enable_enet_clk(1);
 372
 373         return cpu_eth_init(bis);
 374 }
 375
 376 int board_early_init_f(void)
 377 {
 378
 379         setup_iomux_uart();
 380         setup_spi();
 381
 382         return 0;
 383 }
 384
 385 int board_init(void)
 386 {
 387         /* address of boot parameters */
 388         gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 389
 390         setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
 391         setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
 392
 393         return 0;
 394 }
 395
 396 int power_init_board(void)
 397 {
 398         struct pmic *p;
 399         int ret;
 400         unsigned int reg;
 401
 402         ret = power_pfuze100_init(I2C_PMIC);
 403         if (ret)
 404                 return ret;
 405
 406         p = pmic_get("PFUZE100");
 407         ret = pmic_probe(p);
 408         if (ret)
 409                 return ret;
 410
 411         pmic_reg_read(p, PFUZE100_DEVICEID, &reg);
 412         printf("PMIC:  PFUZE100 ID=0x%02x\n", reg);
 413
 414         /* Increase VGEN3 from 2.5 to 2.8V */
 415         pmic_reg_read(p, PFUZE100_VGEN3VOL, &reg);
 416         reg &= ~LDO_VOL_MASK;
 417         reg |= LDOB_2_80V;
 418         pmic_reg_write(p, PFUZE100_VGEN3VOL, reg);
 419
 420         /* Increase VGEN5 from 2.8 to 3V */
 421         pmic_reg_read(p, PFUZE100_VGEN5VOL, &reg);
 422         reg &= ~LDO_VOL_MASK;
 423         reg |= LDOB_3_00V;
 424         pmic_reg_write(p, PFUZE100_VGEN5VOL, reg);
 425
 426         /* Set SW1AB stanby volage to 0.975V */
 427         pmic_reg_read(p, PFUZE100_SW1ABSTBY, &reg);
 428         reg &= ~SW1x_STBY_MASK;
 429         reg |= SW1x_0_975V;
 430         pmic_reg_write(p, PFUZE100_SW1ABSTBY, reg);
 431
 432         /* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
 433         pmic_reg_read(p, PFUZE100_SW1ABCONF, &reg);
 434         reg &= ~SW1xCONF_DVSSPEED_MASK;
 435         reg |= SW1xCONF_DVSSPEED_4US;
 436         pmic_reg_write(p, PFUZE100_SW1ABCONF, reg);
 437
 438         /* Set SW1C standby voltage to 0.975V */
 439         pmic_reg_read(p, PFUZE100_SW1CSTBY, &reg);
 440         reg &= ~SW1x_STBY_MASK;
 441         reg |= SW1x_0_975V;
 442         pmic_reg_write(p, PFUZE100_SW1CSTBY, reg);
 443
 444         /* Set SW1C/VDDSOC step ramp up time from 16us to 4us/25mV */
 445         pmic_reg_read(p, PFUZE100_SW1CCONF, &reg);
 446         reg &= ~SW1xCONF_DVSSPEED_MASK;
 447         reg |= SW1xCONF_DVSSPEED_4US;
 448         pmic_reg_write(p, PFUZE100_SW1CCONF, reg);
 449
 450         return 0;
 451 }
 452
 453 #ifdef CONFIG_CMD_BMODE
 454 static const struct boot_mode board_boot_modes[] = {
 455         /* 4 bit bus width */
 456         {"sd2",  MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
 457         /* 8 bit bus width */
 458         {"emmc", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
 459         {NULL,   0},
 460 };
 461 #endif
 462
 463 int board_late_init(void)
 464 {
 465 #ifdef CONFIG_CMD_BMODE
 466         add_board_boot_modes(board_boot_modes);
 467 #endif
 468
 469         env_set("board_name", BOARD_NAME);
 470         return 0;
 471 }
 472
 473 int checkboard(void)
 474 {
 475         puts("Board: ");
 476         puts(BOARD_NAME "\n");
 477
 478         return 0;
 479 }
 480
 481 #ifdef CONFIG_SPL_BUILD
 482 #include <spl.h>
 483 #include <libfdt.h>
 484
 485 const struct mx6dq_iomux_ddr_regs mx6_ddr_ioregs = {
 486         .dram_sdclk_0 =  0x00020030,
 487         .dram_sdclk_1 =  0x00020030,
 488         .dram_cas =  0x00020030,
 489         .dram_ras =  0x00020030,
 490         .dram_reset =  0x00020030,
 491         .dram_sdcke0 =  0x00003000,
 492         .dram_sdcke1 =  0x00003000,
 493         .dram_sdba2 =  0x00000000,
 494         .dram_sdodt0 =  0x00003030,
 495         .dram_sdodt1 =  0x00003030,
 496         .dram_sdqs0 =  0x00000030,
 497         .dram_sdqs1 =  0x00000030,
 498         .dram_sdqs2 =  0x00000030,
 499         .dram_sdqs3 =  0x00000030,
 500         .dram_sdqs4 =  0x00000030,
 501         .dram_sdqs5 =  0x00000030,
 502         .dram_sdqs6 =  0x00000030,
 503         .dram_sdqs7 =  0x00000030,
 504         .dram_dqm0 =  0x00020030,
 505         .dram_dqm1 =  0x00020030,
 506         .dram_dqm2 =  0x00020030,
 507         .dram_dqm3 =  0x00020030,
 508         .dram_dqm4 =  0x00020030,
 509         .dram_dqm5 =  0x00020030,
 510         .dram_dqm6 =  0x00020030,
 511         .dram_dqm7 =  0x00020030,
 512 };
 513
 514 const struct mx6dq_iomux_grp_regs mx6_grp_ioregs = {
 515         .grp_ddr_type =  0x000C0000,
 516         .grp_ddrmode_ctl =  0x00020000,
 517         .grp_ddrpke =  0x00000000,
 518         .grp_addds =  0x00000030,
 519         .grp_ctlds =  0x00000030,
 520         .grp_ddrmode =  0x00020000,
 521         .grp_b0ds =  0x00000030,
 522         .grp_b1ds =  0x00000030,
 523         .grp_b2ds =  0x00000030,
 524         .grp_b3ds =  0x00000030,
 525         .grp_b4ds =  0x00000030,
 526         .grp_b5ds =  0x00000030,
 527         .grp_b6ds =  0x00000030,
 528         .grp_b7ds =  0x00000030,
 529 };
 530
 531 const struct mx6_mmdc_calibration mx6_mmcd_calib = {
 532         .p0_mpwldectrl0 =  0x001F001F,
 533         .p0_mpwldectrl1 =  0x001F001F,
 534         .p1_mpwldectrl0 =  0x00440044,
 535         .p1_mpwldectrl1 =  0x00440044,
 536         .p0_mpdgctrl0 =  0x434B0350,
 537         .p0_mpdgctrl1 =  0x034C0359,
 538         .p1_mpdgctrl0 =  0x434B0350,
 539         .p1_mpdgctrl1 =  0x03650348,
 540         .p0_mprddlctl =  0x4436383B,
 541         .p1_mprddlctl =  0x39393341,
 542         .p0_mpwrdlctl =  0x35373933,
 543         .p1_mpwrdlctl =  0x48254A36,
 544 };
 545
 546 /* MT41K128M16JT-125 */
 547 static struct mx6_ddr3_cfg mem_ddr = {
 548         .mem_speed = 1600,
 549         .density = 2,
 550         .width = 16,
 551         .banks = 8,
 552         .rowaddr = 14,
 553         .coladdr = 10,
 554         .pagesz = 2,
 555         .trcd = 1375,
 556         .trcmin = 4875,
 557         .trasmin = 3500,
 558 };
 559
 560 static void ccgr_init(void)
 561 {
 562         struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 563
 564         writel(0x00C03F3F, &ccm->CCGR0);
 565         writel(0x0030FC03, &ccm->CCGR1);
 566         writel(0x0FFFC000, &ccm->CCGR2);
 567         writel(0x3FF00000, &ccm->CCGR3);
 568         writel(0x00FFF300, &ccm->CCGR4);
 569         writel(0x0F0000C3, &ccm->CCGR5);
 570         writel(0x000003FF, &ccm->CCGR6);
 571 }
 572
 573 /*
 574  * This section requires the differentiation between iMX6 Sabre boards, but
 575  * for now, it will configure only for the mx6q variant.
 576  */
 577 static void spl_dram_init(void)
 578 {
 579         struct mx6_ddr_sysinfo sysinfo = {
 580                 /* width of data bus:0=16,1=32,2=64 */
 581                 .dsize = 2,
 582                 /* config for full 4GB range so that get_mem_size() works */
 583                 .cs_density = 32, /* 32Gb per CS */
 584                 /* single chip select */
 585                 .ncs = 1,
 586                 .cs1_mirror = 0,
 587                 .rtt_wr = 1 /*DDR3_RTT_60_OHM*/,        /* RTT_Wr = RZQ/4 */
 588                 .rtt_nom = 1 /*DDR3_RTT_60_OHM*/,       /* RTT_Nom = RZQ/4 */
 589                 .walat = 1,     /* Write additional latency */
 590                 .ralat = 5,     /* Read additional latency */
 591                 .mif3_mode = 3, /* Command prediction working mode */
 592                 .bi_on = 1,     /* Bank interleaving enabled */
 593                 .sde_to_rst = 0x10,     /* 14 cycles, 200us (JEDEC default) */
 594                 .rst_to_cke = 0x23,     /* 33 cycles, 500us (JEDEC default) */
 595                 .ddr_type = DDR_TYPE_DDR3,
 596                 .refsel = 1,    /* Refresh cycles at 32KHz */
 597                 .refr = 7,      /* 8 refresh commands per refresh cycle */
 598         };
 599
 600         mx6dq_dram_iocfg(64, &mx6_ddr_ioregs, &mx6_grp_ioregs);
 601         mx6_dram_cfg(&sysinfo, &mx6_mmcd_calib, &mem_ddr);
 602 }
 603
 604 void board_init_f(ulong dummy)
 605 {
 606         /* setup AIPS and disable watchdog */
 607         arch_cpu_init();
 608
 609         ccgr_init();
 610         gpr_init();
 611
 612         /* iomux and setup of i2c */
 613         board_early_init_f();
 614
 615         /* setup GP timer */
 616         timer_init();
 617
 618         /* UART clocks enabled and gd valid - init serial console */
 619         preloader_console_init();
 620
 621         /* DDR initialization */
 622         spl_dram_init();
 623
 624         /* Clear the BSS. */
 625         memset(__bss_start, 0, __bss_end - __bss_start);
 626
 627         /* load/boot image from boot device */
 628         board_init_r(NULL, 0);
 629 }
 630
 631 #endif