1 // SPDX-License-Identifier: GPL-2.0+
3 * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
5 * Based on da830evm.c. Original Copyrights follow:
7 * Copyright (C) 2009 Nick Thompson, GE Fanuc, Ltd. <nick.thompson@gefanuc.com>
8 * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
14 #include <environment.h>
18 #include <spi_flash.h>
19 #include <asm/arch/hardware.h>
20 #include <asm/ti-common/davinci_nand.h>
21 #include <asm/arch/emac_defs.h>
22 #include <asm/arch/pinmux_defs.h>
24 #include <asm/arch/davinci_misc.h>
25 #include <linux/errno.h>
27 #include <asm/mach-types.h>
30 #ifdef CONFIG_MMC_DAVINCI
32 #include <asm/arch/sdmmc_defs.h>
35 DECLARE_GLOBAL_DATA_PTR;
37 #ifdef CONFIG_DRIVER_TI_EMAC
38 #ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
43 #endif /* CONFIG_DRIVER_TI_EMAC */
45 #define CFG_MAC_ADDR_SPI_BUS 0
46 #define CFG_MAC_ADDR_SPI_CS 0
47 #define CFG_MAC_ADDR_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
48 #define CFG_MAC_ADDR_SPI_MODE SPI_MODE_3
50 #define CFG_MAC_ADDR_OFFSET (flash->size - SZ_64K)
52 #ifdef CONFIG_MAC_ADDR_IN_SPIFLASH
53 static int get_mac_addr(u8 *addr)
55 struct spi_flash *flash;
58 flash = spi_flash_probe(CFG_MAC_ADDR_SPI_BUS, CFG_MAC_ADDR_SPI_CS,
59 CFG_MAC_ADDR_SPI_MAX_HZ, CFG_MAC_ADDR_SPI_MODE);
61 printf("Error - unable to probe SPI flash.\n");
65 ret = spi_flash_read(flash, (CFG_MAC_ADDR_OFFSET), 6, addr);
67 printf("Error - unable to read MAC address from SPI flash.\n");
75 void dsp_lpsc_on(unsigned domain, unsigned int id)
77 dv_reg_p mdstat, mdctl, ptstat, ptcmd;
78 struct davinci_psc_regs *psc_regs;
80 psc_regs = davinci_psc0_regs;
81 mdstat = &psc_regs->psc0.mdstat[id];
82 mdctl = &psc_regs->psc0.mdctl[id];
83 ptstat = &psc_regs->ptstat;
84 ptcmd = &psc_regs->ptcmd;
86 while (*ptstat & (0x1 << domain))
89 if ((*mdstat & 0x1f) == 0x03)
90 return; /* Already on and enabled */
94 *ptcmd = 0x1 << domain;
96 while (*ptstat & (0x1 << domain))
98 while ((*mdstat & 0x1f) != 0x03)
99 ; /* Probably an overkill... */
102 static void dspwake(void)
104 unsigned *resetvect = (unsigned *)DAVINCI_L3CBARAM_BASE;
107 /* if the device is ARM only, return */
108 if ((readl(CHIP_REV_ID_REG) & 0x3f) == 0x10)
111 if (hwconfig_subarg_cmp_f("dsp", "wake", "no", NULL))
114 *resetvect++ = 0x1E000; /* DSP Idle */
115 /* clear out the next 10 words as NOP */
116 memset(resetvect, 0, sizeof(unsigned) *10);
118 /* setup the DSP reset vector */
119 writel(DAVINCI_L3CBARAM_BASE, HOST1CFG);
121 dsp_lpsc_on(1, DAVINCI_LPSC_GEM);
122 val = readl(PSC0_MDCTL + (15 * 4));
124 writel(val, (PSC0_MDCTL + (15 * 4)));
127 int misc_init_r(void)
131 #if defined(CONFIG_MAC_ADDR_IN_SPIFLASH) || defined(CONFIG_MAC_ADDR_IN_EEPROM)
133 uchar env_enetaddr[6];
136 enetaddr_found = eth_env_get_enetaddr("ethaddr", env_enetaddr);
140 #ifdef CONFIG_MAC_ADDR_IN_SPIFLASH
144 spi_mac_read = get_mac_addr(buff);
148 * MAC address not present in the environment
149 * try and read the MAC address from SPI flash
152 if (!enetaddr_found) {
154 if (is_valid_ethaddr(buff)) {
155 if (eth_env_set_enetaddr("ethaddr", buff)) {
156 printf("Warning: Failed to "
157 "set MAC address from SPI flash\n");
160 printf("Warning: Invalid "
161 "MAC address read from SPI flash\n");
166 * MAC address present in environment compare it with
167 * the MAC address in SPI flash and warn on mismatch
169 if (!spi_mac_read && is_valid_ethaddr(buff) &&
170 memcmp(env_enetaddr, buff, 6))
171 printf("Warning: MAC address in SPI flash don't match "
172 "with the MAC address in the environment\n");
173 printf("Default using MAC address from environment\n");
176 #elif defined(CONFIG_MAC_ADDR_IN_EEPROM)
180 /* Read Ethernet MAC address from EEPROM */
181 eeprom_mac_read = dvevm_read_mac_address(enetaddr);
184 * MAC address not present in the environment
185 * try and read the MAC address from EEPROM flash
188 if (!enetaddr_found) {
190 /* Set Ethernet MAC address from EEPROM */
191 davinci_sync_env_enetaddr(enetaddr);
194 * MAC address present in environment compare it with
195 * the MAC address in EEPROM and warn on mismatch
197 if (eeprom_mac_read && memcmp(enetaddr, env_enetaddr, 6))
198 printf("Warning: MAC address in EEPROM don't match "
199 "with the MAC address in the environment\n");
200 printf("Default using MAC address from environment\n");
207 static const struct pinmux_config gpio_pins[] = {
208 #ifdef CONFIG_USE_NOR
209 /* GP0[11] is required for NOR to work on Rev 3 EVMs */
210 { pinmux(0), 8, 4 }, /* GP0[11] */
212 #ifdef CONFIG_MMC_DAVINCI
213 /* GP0[11] is required for SD to work on Rev 3 EVMs */
214 { pinmux(0), 8, 4 }, /* GP0[11] */
218 const struct pinmux_resource pinmuxes[] = {
219 #ifdef CONFIG_DRIVER_TI_EMAC
220 PINMUX_ITEM(emac_pins_mdio),
221 #ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
222 PINMUX_ITEM(emac_pins_rmii),
224 PINMUX_ITEM(emac_pins_mii),
227 #ifdef CONFIG_SPI_FLASH
228 PINMUX_ITEM(spi1_pins_base),
229 PINMUX_ITEM(spi1_pins_scs0),
231 PINMUX_ITEM(uart2_pins_txrx),
232 PINMUX_ITEM(uart2_pins_rtscts),
233 PINMUX_ITEM(i2c0_pins),
234 #ifdef CONFIG_NAND_DAVINCI
235 PINMUX_ITEM(emifa_pins_cs3),
236 PINMUX_ITEM(emifa_pins_cs4),
237 PINMUX_ITEM(emifa_pins_nand),
238 #elif defined(CONFIG_USE_NOR)
239 PINMUX_ITEM(emifa_pins_cs2),
240 PINMUX_ITEM(emifa_pins_nor),
242 PINMUX_ITEM(gpio_pins),
243 #ifdef CONFIG_MMC_DAVINCI
244 PINMUX_ITEM(mmc0_pins),
248 const int pinmuxes_size = ARRAY_SIZE(pinmuxes);
250 const struct lpsc_resource lpsc[] = {
251 { DAVINCI_LPSC_AEMIF }, /* NAND, NOR */
252 { DAVINCI_LPSC_SPI1 }, /* Serial Flash */
253 { DAVINCI_LPSC_EMAC }, /* image download */
254 { DAVINCI_LPSC_UART2 }, /* console */
255 { DAVINCI_LPSC_GPIO },
256 #ifdef CONFIG_MMC_DAVINCI
257 { DAVINCI_LPSC_MMC_SD },
261 const int lpsc_size = ARRAY_SIZE(lpsc);
263 #ifndef CONFIG_DA850_EVM_MAX_CPU_CLK
264 #define CONFIG_DA850_EVM_MAX_CPU_CLK 300000000
267 #define REV_AM18X_EVM 0x100
270 * get_board_rev() - setup to pass kernel board revision information
272 * bit[0-3] Maximum cpu clock rate supported by onboard SoC
278 u32 get_board_rev(void)
281 u32 maxcpuclk = CONFIG_DA850_EVM_MAX_CPU_CLK;
284 s = env_get("maxcpuclk");
286 maxcpuclk = simple_strtoul(s, NULL, 10);
288 if (maxcpuclk >= 456000000)
290 else if (maxcpuclk >= 408000000)
292 else if (maxcpuclk >= 372000000)
297 int board_early_init_f(void)
300 * Power on required peripherals
301 * ARM does not have access by default to PSC0 and PSC1
302 * assuming here that the DSP bootloader has set the IOPU
303 * such that PSC access is available to ARM
305 if (da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc)))
315 #ifdef CONFIG_NAND_DAVINCI
317 * NAND CS setup - cycle counts based on da850evm NAND timings in the
318 * Linux kernel @ 25MHz EMIFA
320 writel((DAVINCI_ABCR_WSETUP(2) |
321 DAVINCI_ABCR_WSTROBE(2) |
322 DAVINCI_ABCR_WHOLD(1) |
323 DAVINCI_ABCR_RSETUP(1) |
324 DAVINCI_ABCR_RSTROBE(4) |
325 DAVINCI_ABCR_RHOLD(0) |
327 DAVINCI_ABCR_ASIZE_8BIT),
328 &davinci_emif_regs->ab2cr); /* CS3 */
331 /* arch number of the board */
332 gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_DA850_EVM;
334 /* address of boot parameters */
335 gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
337 /* setup the SUSPSRC for ARM to control emulation suspend */
338 writel(readl(&davinci_syscfg_regs->suspsrc) &
339 ~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C |
340 DAVINCI_SYSCFG_SUSPSRC_SPI1 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 |
341 DAVINCI_SYSCFG_SUSPSRC_UART2),
342 &davinci_syscfg_regs->suspsrc);
344 #ifdef CONFIG_USE_NOR
345 /* Set the GPIO direction as output */
346 clrbits_le32((u32 *)GPIO_BANK0_REG_DIR_ADDR, (0x01 << 11));
348 /* Set the output as low */
349 writel(0x01 << 11, GPIO_BANK0_REG_CLR_ADDR);
352 #ifdef CONFIG_MMC_DAVINCI
353 /* Set the GPIO direction as output */
354 clrbits_le32((u32 *)GPIO_BANK0_REG_DIR_ADDR, (0x01 << 11));
356 /* Set the output as high */
357 writel(0x01 << 11, GPIO_BANK0_REG_SET_ADDR);
360 #ifdef CONFIG_DRIVER_TI_EMAC
361 davinci_emac_mii_mode_sel(HAS_RMII);
362 #endif /* CONFIG_DRIVER_TI_EMAC */
367 #ifdef CONFIG_DRIVER_TI_EMAC
369 #ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
373 * DA850/OMAP-L138 EVM can interface to a daughter card for
374 * additional features. This card has an I2C GPIO Expander TCA6416
375 * to select the required functions like camera, RMII Ethernet,
376 * character LCD, video.
378 * Initialization of the expander involves configuring the
379 * polarity and direction of the ports. P07-P05 are used here.
380 * These ports are connected to a Mux chip which enables only one
381 * functionality at a time.
383 * For RMII phy to respond, the MII MDIO clock has to be disabled
384 * since both the PHY devices have address as zero. The MII MDIO
385 * clock is controlled via GPIO2[6].
387 * This code is valid for Beta version of the hardware
389 int rmii_hw_init(void)
391 const struct pinmux_config gpio_pins[] = {
398 /* PinMux for GPIO */
399 if (davinci_configure_pin_mux(gpio_pins, ARRAY_SIZE(gpio_pins)) != 0)
402 /* I2C Exapnder configuration */
403 /* Set polarity to non-inverted */
406 ret = i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 4, 1, buf, 2);
408 printf("\nExpander @ 0x%02x write FAILED!!!\n",
409 CONFIG_SYS_I2C_EXPANDER_ADDR);
413 /* Configure P07-P05 as outputs */
416 ret = i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 6, 1, buf, 2);
418 printf("\nExpander @ 0x%02x write FAILED!!!\n",
419 CONFIG_SYS_I2C_EXPANDER_ADDR);
422 /* For Ethernet RMII selection
427 if (i2c_read(CONFIG_SYS_I2C_EXPANDER_ADDR, 2, 1, buf, 1)) {
428 printf("\nExpander @ 0x%02x read FAILED!!!\n",
429 CONFIG_SYS_I2C_EXPANDER_ADDR);
433 buf[0] |= (0 << 7) | (1 << 6) | (1 << 5);
434 if (i2c_write(CONFIG_SYS_I2C_EXPANDER_ADDR, 2, 1, buf, 1)) {
435 printf("\nExpander @ 0x%02x write FAILED!!!\n",
436 CONFIG_SYS_I2C_EXPANDER_ADDR);
439 /* Set the output as high */
440 temp = REG(GPIO_BANK2_REG_SET_ADDR);
442 REG(GPIO_BANK2_REG_SET_ADDR) = temp;
444 /* Set the GPIO direction as output */
445 temp = REG(GPIO_BANK2_REG_DIR_ADDR);
446 temp &= ~(0x01 << 6);
447 REG(GPIO_BANK2_REG_DIR_ADDR) = temp;
451 #endif /* CONFIG_DRIVER_TI_EMAC_USE_RMII */
454 * Initializes on-board ethernet controllers.
456 int board_eth_init(bd_t *bis)
458 #ifdef CONFIG_DRIVER_TI_EMAC_USE_RMII
459 /* Select RMII fucntion through the expander */
461 printf("RMII hardware init failed!!!\n");
465 #endif /* CONFIG_DRIVER_TI_EMAC */