board/congatec/cgtqmx6eval/cgtqmx6eval.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
   4  * Based on mx6qsabrelite.c file
   5  * Copyright (C) 2013, Adeneo Embedded <www.adeneo-embedded.com>
   6  * Leo Sartre, <lsartre@adeneo-embedded.com>
   7  */
   8
   9 #include <common.h>
  10 #include <asm/io.h>
  11 #include <asm/arch/clock.h>
  12 #include <asm/arch/imx-regs.h>
  13 #include <asm/arch/iomux.h>
  14 #include <asm/arch/mx6-pins.h>
  15 #include <asm/gpio.h>
  16 #include <asm/mach-imx/iomux-v3.h>
  17 #include <asm/mach-imx/sata.h>
  18 #include <asm/mach-imx/boot_mode.h>
  19 #include <asm/mach-imx/mxc_i2c.h>
  20 #include <asm/arch/sys_proto.h>
  21 #include <asm/arch/mxc_hdmi.h>
  22 #include <asm/arch/crm_regs.h>
  23 #include <mmc.h>
  24 #include <fsl_esdhc_imx.h>
  25 #include <i2c.h>
  26 #include <input.h>
  27 #include <power/pmic.h>
  28 #include <power/pfuze100_pmic.h>
  29 #include <linux/fb.h>
  30 #include <ipu_pixfmt.h>
  31 #include <malloc.h>
  32 #include <miiphy.h>
  33 #include <netdev.h>
  34 #include <micrel.h>
  35 #include <spi_flash.h>
  36 #include <spi.h>
  37
  38 DECLARE_GLOBAL_DATA_PTR;
  39
  40 #define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |\
  41         PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  42
  43 #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP  | PAD_CTL_SPEED_LOW |\
  44         PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
  45
  46 #define I2C_PAD_CTRL    (PAD_CTL_PKE | PAD_CTL_PUE |            \
  47         PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
  48         PAD_CTL_DSE_40ohm | PAD_CTL_HYS |                       \
  49         PAD_CTL_ODE | PAD_CTL_SRE_FAST)
  50
  51 #define SPI_PAD_CTRL (PAD_CTL_HYS |                             \
  52         PAD_CTL_SPEED_MED |             \
  53         PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
  54
  55 #define MX6Q_QMX6_PFUZE_MUX             IMX_GPIO_NR(6, 9)
  56
  57
  58 #define ENET_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |             \
  59         PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED   |             \
  60         PAD_CTL_DSE_40ohm   | PAD_CTL_HYS)
  61
  62 int dram_init(void)
  63 {
  64         gd->ram_size = imx_ddr_size();
  65
  66         return 0;
  67 }
  68
  69 static iomux_v3_cfg_t const uart2_pads[] = {
  70         IOMUX_PADS(PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
  71         IOMUX_PADS(PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
  72 };
  73
  74 #ifndef CONFIG_SPL_BUILD
  75 static iomux_v3_cfg_t const usdhc2_pads[] = {
  76         IOMUX_PADS(PAD_SD2_CLK__SD2_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  77         IOMUX_PADS(PAD_SD2_CMD__SD2_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  78         IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  79         IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  80         IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  81         IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  82         IOMUX_PADS(PAD_GPIO_4__GPIO1_IO04      | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  83 };
  84
  85 static iomux_v3_cfg_t const usdhc3_pads[] = {
  86         IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  87         IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  88         IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  89         IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  90         IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  91         IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  92         IOMUX_PADS(PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  93         IOMUX_PADS(PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  94         IOMUX_PADS(PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  95         IOMUX_PADS(PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  96         IOMUX_PADS(PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
  97 };
  98 #endif
  99
 100 static iomux_v3_cfg_t const usdhc4_pads[] = {
 101         IOMUX_PADS(PAD_SD4_CLK__SD4_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 102         IOMUX_PADS(PAD_SD4_CMD__SD4_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 103         IOMUX_PADS(PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 104         IOMUX_PADS(PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 105         IOMUX_PADS(PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 106         IOMUX_PADS(PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 107         IOMUX_PADS(PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 108         IOMUX_PADS(PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 109         IOMUX_PADS(PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 110         IOMUX_PADS(PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
 111         IOMUX_PADS(PAD_NANDF_D6__GPIO2_IO06    | MUX_PAD_CTRL(NO_PAD_CTRL)),
 112 };
 113
 114 static iomux_v3_cfg_t const usb_otg_pads[] = {
 115         IOMUX_PADS(PAD_EIM_D22__USB_OTG_PWR | MUX_PAD_CTRL(NO_PAD_CTRL)),
 116         IOMUX_PADS(PAD_GPIO_1__USB_OTG_ID | MUX_PAD_CTRL(NO_PAD_CTRL)),
 117 };
 118
 119 static iomux_v3_cfg_t enet_pads_ksz9031[] = {
 120         IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 121         IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 122         IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 123         IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 124         IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 125         IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 126         IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 127         IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 128         IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 129         IOMUX_PADS(PAD_RGMII_RXC__GPIO6_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL)),
 130         IOMUX_PADS(PAD_RGMII_RD0__GPIO6_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL)),
 131         IOMUX_PADS(PAD_RGMII_RD1__GPIO6_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL)),
 132         IOMUX_PADS(PAD_RGMII_RD2__GPIO6_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL)),
 133         IOMUX_PADS(PAD_RGMII_RD3__GPIO6_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)),
 134         IOMUX_PADS(PAD_RGMII_RX_CTL__GPIO6_IO24 | MUX_PAD_CTRL(NO_PAD_CTRL)),
 135 };
 136
 137 static iomux_v3_cfg_t enet_pads_final_ksz9031[] = {
 138         IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 139         IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 140         IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 141         IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 142         IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 143         IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 144 };
 145
 146 static iomux_v3_cfg_t enet_pads_ar8035[] = {
 147         IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 148         IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 149         IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 150         IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 151         IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 152         IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 153         IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 154         IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 155         IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 156         IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 157         IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 158         IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 159         IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 160         IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 161         IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL)),
 162 };
 163
 164 static iomux_v3_cfg_t const ecspi1_pads[] = {
 165         IOMUX_PADS(PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL)),
 166         IOMUX_PADS(PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL)),
 167         IOMUX_PADS(PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL)),
 168         IOMUX_PADS(PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL)),
 169 };
 170
 171 #define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
 172 struct i2c_pads_info mx6q_i2c_pad_info1 = {
 173         .scl = {
 174                 .i2c_mode = MX6Q_PAD_KEY_COL3__I2C2_SCL | PC,
 175                 .gpio_mode = MX6Q_PAD_KEY_COL3__GPIO4_IO12 | PC,
 176                 .gp = IMX_GPIO_NR(4, 12)
 177         },
 178         .sda = {
 179                 .i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA | PC,
 180                 .gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13 | PC,
 181                 .gp = IMX_GPIO_NR(4, 13)
 182         }
 183 };
 184
 185 struct i2c_pads_info mx6dl_i2c_pad_info1 = {
 186         .scl = {
 187                 .i2c_mode = MX6DL_PAD_KEY_COL3__I2C2_SCL | PC,
 188                 .gpio_mode = MX6DL_PAD_KEY_COL3__GPIO4_IO12 | PC,
 189                 .gp = IMX_GPIO_NR(4, 12)
 190         },
 191         .sda = {
 192                 .i2c_mode = MX6DL_PAD_KEY_ROW3__I2C2_SDA | PC,
 193                 .gpio_mode = MX6DL_PAD_KEY_ROW3__GPIO4_IO13 | PC,
 194                 .gp = IMX_GPIO_NR(4, 13)
 195         }
 196 };
 197
 198 #define I2C_PMIC        1       /* I2C2 port is used to connect to the PMIC */
 199
 200 struct interface_level {
 201         char *name;
 202         uchar value;
 203 };
 204
 205 static struct interface_level mipi_levels[] = {
 206         {"0V0", 0x00},
 207         {"2V5", 0x17},
 208 };
 209
 210 /* setup board specific PMIC */
 211 int power_init_board(void)
 212 {
 213         struct pmic *p;
 214         u32 id1, id2, i;
 215         int ret;
 216         char const *lv_mipi;
 217
 218         /* configure I2C multiplexer */
 219         gpio_direction_output(MX6Q_QMX6_PFUZE_MUX, 1);
 220
 221         power_pfuze100_init(I2C_PMIC);
 222         p = pmic_get("PFUZE100");
 223         if (!p)
 224                 return -EINVAL;
 225
 226         ret = pmic_probe(p);
 227         if (ret)
 228                 return ret;
 229
 230         pmic_reg_read(p, PFUZE100_DEVICEID, &id1);
 231         pmic_reg_read(p, PFUZE100_REVID, &id2);
 232         printf("PFUZE100 Rev. [%02x/%02x] detected\n", id1, id2);
 233
 234         if (id2 >= 0x20)
 235                 return 0;
 236
 237         /* set level of MIPI if specified */
 238         lv_mipi = env_get("lv_mipi");
 239         if (lv_mipi)
 240                 return 0;
 241
 242         for (i = 0; i < ARRAY_SIZE(mipi_levels); i++) {
 243                 if (!strcmp(mipi_levels[i].name, lv_mipi)) {
 244                         printf("set MIPI level %s\n", mipi_levels[i].name);
 245                         ret = pmic_reg_write(p, PFUZE100_VGEN4VOL,
 246                                              mipi_levels[i].value);
 247                         if (ret)
 248                                 return ret;
 249                 }
 250         }
 251
 252         return 0;
 253 }
 254
 255 int board_eth_init(bd_t *bis)
 256 {
 257         struct phy_device *phydev;
 258         struct mii_dev *bus;
 259         unsigned short id1, id2;
 260         int ret;
 261
 262         /* check whether KSZ9031 or AR8035 has to be configured */
 263         SETUP_IOMUX_PADS(enet_pads_ar8035);
 264
 265         /* phy reset */
 266         gpio_direction_output(IMX_GPIO_NR(3, 23), 0);
 267         udelay(2000);
 268         gpio_set_value(IMX_GPIO_NR(3, 23), 1);
 269         udelay(500);
 270
 271         bus = fec_get_miibus(IMX_FEC_BASE, -1);
 272         if (!bus)
 273                 return -EINVAL;
 274         phydev = phy_find_by_mask(bus, (0xf << 4), PHY_INTERFACE_MODE_RGMII);
 275         if (!phydev) {
 276                 printf("Error: phy device not found.\n");
 277                 ret = -ENODEV;
 278                 goto free_bus;
 279         }
 280
 281         /* get the PHY id */
 282         id1 = phy_read(phydev, MDIO_DEVAD_NONE, 2);
 283         id2 = phy_read(phydev, MDIO_DEVAD_NONE, 3);
 284
 285         if ((id1 == 0x22) && ((id2 & 0xFFF0) == 0x1620)) {
 286                 /* re-configure for Micrel KSZ9031 */
 287                 printf("configure Micrel KSZ9031 Ethernet Phy at address %d\n",
 288                        phydev->addr);
 289
 290                 /* phy reset: gpio3-23 */
 291                 gpio_set_value(IMX_GPIO_NR(3, 23), 0);
 292                 gpio_set_value(IMX_GPIO_NR(6, 30), (phydev->addr >> 2));
 293                 gpio_set_value(IMX_GPIO_NR(6, 25), 1);
 294                 gpio_set_value(IMX_GPIO_NR(6, 27), 1);
 295                 gpio_set_value(IMX_GPIO_NR(6, 28), 1);
 296                 gpio_set_value(IMX_GPIO_NR(6, 29), 1);
 297                 SETUP_IOMUX_PADS(enet_pads_ksz9031);
 298                 gpio_set_value(IMX_GPIO_NR(6, 24), 1);
 299                 udelay(500);
 300                 gpio_set_value(IMX_GPIO_NR(3, 23), 1);
 301                 SETUP_IOMUX_PADS(enet_pads_final_ksz9031);
 302         } else if ((id1 == 0x004d) && (id2 == 0xd072)) {
 303                 /* configure Atheros AR8035 - actually nothing to do */
 304                 printf("configure Atheros AR8035 Ethernet Phy at address %d\n",
 305                        phydev->addr);
 306         } else {
 307                 printf("Unknown Ethernet-Phy: 0x%04x 0x%04x\n", id1, id2);
 308                 ret = -EINVAL;
 309                 goto free_phydev;
 310         }
 311
 312         ret = fec_probe(bis, -1, IMX_FEC_BASE, bus, phydev);
 313         if (ret)
 314                 goto free_phydev;
 315
 316         return 0;
 317
 318 free_phydev:
 319         free(phydev);
 320 free_bus:
 321         free(bus);
 322         return ret;
 323 }
 324
 325 int mx6_rgmii_rework(struct phy_device *phydev)
 326 {
 327         unsigned short id1, id2;
 328         unsigned short val;
 329
 330         /* check whether KSZ9031 or AR8035 has to be configured */
 331         id1 = phy_read(phydev, MDIO_DEVAD_NONE, 2);
 332         id2 = phy_read(phydev, MDIO_DEVAD_NONE, 3);
 333
 334         if ((id1 == 0x22) && ((id2 & 0xFFF0) == 0x1620)) {
 335                 /* finalize phy configuration for Micrel KSZ9031 */
 336                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 2);
 337                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 4);
 338                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_POST_INC_W | 0x2);
 339                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x0000);
 340
 341                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 2);
 342                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 5);
 343                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_POST_INC_W | 0x2);
 344                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, MII_KSZ9031_MOD_REG);
 345
 346                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 2);
 347                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 6);
 348                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_POST_INC_W | 0x2);
 349                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0xFFFF);
 350
 351                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 2);
 352                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 8);
 353                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_POST_INC_W | 0x2);
 354                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x3FFF);
 355
 356                 /* fix KSZ9031 link up issue */
 357                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 0x0);
 358                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x4);
 359                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_NO_POST_INC);
 360                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x6);
 361                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_REG);
 362                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x3);
 363                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_NO_POST_INC);
 364                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, 0x1A80);
 365         }
 366
 367         if ((id1 == 0x004d) && (id2 == 0xd072)) {
 368                 /* enable AR8035 ouput a 125MHz clk from CLK_25M */
 369                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, 0x7);
 370                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, MII_KSZ9031_MOD_DATA_POST_INC_RW | 0x16);
 371                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_CONTROL, MII_KSZ9031_MOD_DATA_NO_POST_INC | 0x7);
 372                 val = phy_read(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA);
 373                 val &= 0xfe63;
 374                 val |= 0x18;
 375                 phy_write(phydev, MDIO_DEVAD_NONE, MMD_ACCESS_REG_DATA, val);
 376
 377                 /* introduce tx clock delay */
 378                 phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
 379                 val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
 380                 val |= 0x0100;
 381                 phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
 382
 383                 /* disable hibernation */
 384                 phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0xb);
 385                 val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
 386                 phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x3c40);
 387         }
 388         return 0;
 389 }
 390
 391 int board_phy_config(struct phy_device *phydev)
 392 {
 393         mx6_rgmii_rework(phydev);
 394
 395         if (phydev->drv->config)
 396                 phydev->drv->config(phydev);
 397
 398         return 0;
 399 }
 400
 401 static void setup_iomux_uart(void)
 402 {
 403         SETUP_IOMUX_PADS(uart2_pads);
 404 }
 405
 406 #ifdef CONFIG_MXC_SPI
 407 static void setup_spi(void)
 408 {
 409         SETUP_IOMUX_PADS(ecspi1_pads);
 410         gpio_direction_output(IMX_GPIO_NR(3, 19), 0);
 411 }
 412 #endif
 413
 414 #ifdef CONFIG_FSL_ESDHC_IMX
 415 static struct fsl_esdhc_cfg usdhc_cfg[] = {
 416         {USDHC2_BASE_ADDR},
 417         {USDHC3_BASE_ADDR},
 418         {USDHC4_BASE_ADDR},
 419 };
 420
 421 int board_mmc_getcd(struct mmc *mmc)
 422 {
 423         struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
 424         int ret = 0;
 425
 426         switch (cfg->esdhc_base) {
 427         case USDHC2_BASE_ADDR:
 428                 gpio_direction_input(IMX_GPIO_NR(1, 4));
 429                 ret = !gpio_get_value(IMX_GPIO_NR(1, 4));
 430                 break;
 431         case USDHC3_BASE_ADDR:
 432                 ret = 1;        /* eMMC is always present */
 433                 break;
 434         case USDHC4_BASE_ADDR:
 435                 gpio_direction_input(IMX_GPIO_NR(2, 6));
 436                 ret = !gpio_get_value(IMX_GPIO_NR(2, 6));
 437                 break;
 438         default:
 439                 printf("Bad USDHC interface\n");
 440         }
 441
 442         return ret;
 443 }
 444
 445 int board_mmc_init(bd_t *bis)
 446 {
 447 #ifndef CONFIG_SPL_BUILD
 448         s32 status = 0;
 449         int i;
 450
 451         usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
 452         usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
 453         usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
 454
 455         SETUP_IOMUX_PADS(usdhc2_pads);
 456         SETUP_IOMUX_PADS(usdhc3_pads);
 457         SETUP_IOMUX_PADS(usdhc4_pads);
 458
 459         for (i = 0; i < ARRAY_SIZE(usdhc_cfg); i++) {
 460                 status = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
 461                 if (status)
 462                         return status;
 463         }
 464
 465         return 0;
 466 #else
 467         SETUP_IOMUX_PADS(usdhc4_pads);
 468         usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR;
 469         usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
 470         gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
 471
 472         return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
 473 #endif
 474 }
 475 #endif
 476
 477 int board_ehci_hcd_init(int port)
 478 {
 479         switch (port) {
 480         case 0:
 481                 SETUP_IOMUX_PADS(usb_otg_pads);
 482                 /*
 483                  * set daisy chain for otg_pin_id on 6q.
 484                  * for 6dl, this bit is reserved
 485                  */
 486                 imx_iomux_set_gpr_register(1, 13, 1, 1);
 487                 break;
 488         case 1:
 489                 /* nothing to do */
 490                 break;
 491         default:
 492                 printf("Invalid USB port: %d\n", port);
 493                 return -EINVAL;
 494         }
 495
 496         return 0;
 497 }
 498
 499 int board_ehci_power(int port, int on)
 500 {
 501         switch (port) {
 502         case 0:
 503                 break;
 504         case 1:
 505                 gpio_direction_output(IMX_GPIO_NR(5, 5), on);
 506                 break;
 507         default:
 508                 printf("Invalid USB port: %d\n", port);
 509                 return -EINVAL;
 510         }
 511
 512         return 0;
 513 }
 514
 515 struct display_info_t {
 516         int bus;
 517         int addr;
 518         int pixfmt;
 519         int (*detect)(struct display_info_t const *dev);
 520         void (*enable)(struct display_info_t const *dev);
 521         struct fb_videomode mode;
 522 };
 523
 524 static void disable_lvds(struct display_info_t const *dev)
 525 {
 526         struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
 527
 528         clrbits_le32(&iomux->gpr[2], IOMUXC_GPR2_LVDS_CH0_MODE_MASK |
 529                      IOMUXC_GPR2_LVDS_CH1_MODE_MASK);
 530 }
 531
 532 static void do_enable_hdmi(struct display_info_t const *dev)
 533 {
 534         disable_lvds(dev);
 535         imx_enable_hdmi_phy();
 536 }
 537
 538 static struct display_info_t const displays[] = {
 539 {
 540         .bus = -1,
 541         .addr = 0,
 542         .pixfmt = IPU_PIX_FMT_RGB666,
 543         .detect = NULL,
 544         .enable = NULL,
 545         .mode = {
 546                 .name =
 547                 "Hannstar-XGA",
 548                 .refresh = 60,
 549                 .xres = 1024,
 550                 .yres = 768,
 551                 .pixclock = 15385,
 552                 .left_margin = 220,
 553                 .right_margin = 40,
 554                 .upper_margin = 21,
 555                 .lower_margin = 7,
 556                 .hsync_len = 60,
 557                 .vsync_len = 10,
 558                 .sync = FB_SYNC_EXT,
 559                 .vmode = FB_VMODE_NONINTERLACED } },
 560 {
 561         .bus = -1,
 562         .addr = 0,
 563         .pixfmt = IPU_PIX_FMT_RGB24,
 564         .detect = NULL,
 565         .enable = do_enable_hdmi,
 566         .mode = {
 567                 .name = "HDMI",
 568                 .refresh = 60,
 569                 .xres = 1024,
 570                 .yres = 768,
 571                 .pixclock = 15385,
 572                 .left_margin = 220,
 573                 .right_margin = 40,
 574                 .upper_margin = 21,
 575                 .lower_margin = 7,
 576                 .hsync_len = 60,
 577                 .vsync_len = 10,
 578                 .sync = FB_SYNC_EXT,
 579                 .vmode = FB_VMODE_NONINTERLACED } }
 580 };
 581
 582 int board_video_skip(void)
 583 {
 584         int i;
 585         int ret;
 586         char const *panel = env_get("panel");
 587         if (!panel) {
 588                 for (i = 0; i < ARRAY_SIZE(displays); i++) {
 589                         struct display_info_t const *dev = displays + i;
 590                         if (dev->detect && dev->detect(dev)) {
 591                                 panel = dev->mode.name;
 592                                 printf("auto-detected panel %s\n", panel);
 593                                 break;
 594                         }
 595                 }
 596                 if (!panel) {
 597                         panel = displays[0].mode.name;
 598                         printf("No panel detected: default to %s\n", panel);
 599                         i = 0;
 600                 }
 601         } else {
 602                 for (i = 0; i < ARRAY_SIZE(displays); i++) {
 603                         if (!strcmp(panel, displays[i].mode.name))
 604                                 break;
 605                 }
 606         }
 607         if (i < ARRAY_SIZE(displays)) {
 608                 ret = ipuv3_fb_init(&displays[i].mode, 0, displays[i].pixfmt);
 609                 if (!ret) {
 610                         if (displays[i].enable)
 611                                 displays[i].enable(displays + i);
 612                         printf("Display: %s (%ux%u)\n",
 613                                displays[i].mode.name, displays[i].mode.xres,
 614                                displays[i].mode.yres);
 615                 } else
 616                         printf("LCD %s cannot be configured: %d\n",
 617                                displays[i].mode.name, ret);
 618         } else {
 619                 printf("unsupported panel %s\n", panel);
 620                 return -EINVAL;
 621         }
 622
 623         return 0;
 624 }
 625
 626 static void setup_display(void)
 627 {
 628         struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 629         struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
 630         int reg;
 631
 632         enable_ipu_clock();
 633         imx_setup_hdmi();
 634
 635         /* Turn on LDB0, LDB1, IPU,IPU DI0 clocks */
 636         setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK |
 637                      MXC_CCM_CCGR3_LDB_DI1_MASK);
 638
 639         /* set LDB0, LDB1 clk select to 011/011 */
 640         reg = readl(&mxc_ccm->cs2cdr);
 641         reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK |
 642                  MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
 643         reg |= (3 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) |
 644                 (3 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
 645         writel(reg, &mxc_ccm->cs2cdr);
 646
 647         setbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV |
 648                      MXC_CCM_CSCMR2_LDB_DI1_IPU_DIV);
 649
 650         setbits_le32(&mxc_ccm->chsccdr, CHSCCDR_CLK_SEL_LDB_DI0 <<
 651                      MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET |
 652                      CHSCCDR_CLK_SEL_LDB_DI0 <<
 653                      MXC_CCM_CHSCCDR_IPU1_DI1_CLK_SEL_OFFSET);
 654
 655         reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
 656                 | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_LOW
 657                 | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW
 658                 | IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG
 659                 | IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT
 660                 | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
 661                 | IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT
 662                 | IOMUXC_GPR2_LVDS_CH0_MODE_DISABLED
 663                 | IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0;
 664         writel(reg, &iomux->gpr[2]);
 665
 666         reg = readl(&iomux->gpr[3]);
 667         reg = (reg & ~(IOMUXC_GPR3_LVDS1_MUX_CTL_MASK |
 668                        IOMUXC_GPR3_HDMI_MUX_CTL_MASK)) |
 669                 (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 <<
 670                  IOMUXC_GPR3_LVDS1_MUX_CTL_OFFSET);
 671         writel(reg, &iomux->gpr[3]);
 672 }
 673
 674 /*
 675  * Do not overwrite the console
 676  * Use always serial for U-Boot console
 677  */
 678 int overwrite_console(void)
 679 {
 680         return 1;
 681 }
 682
 683 int board_early_init_f(void)
 684 {
 685         setup_iomux_uart();
 686 #ifdef CONFIG_MXC_SPI
 687         setup_spi();
 688 #endif
 689         return 0;
 690 }
 691
 692 int board_init(void)
 693 {
 694         /* address of boot parameters */
 695         gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
 696
 697
 698         if (is_mx6dq())
 699                 setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info1);
 700         else
 701                 setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info1);
 702
 703         setup_display();
 704
 705 #ifdef CONFIG_SATA
 706         setup_sata();
 707 #endif
 708
 709         return 0;
 710 }
 711
 712 int checkboard(void)
 713 {
 714         char *type = "unknown";
 715
 716         if (is_cpu_type(MXC_CPU_MX6Q))
 717                 type = "Quad";
 718         else if (is_cpu_type(MXC_CPU_MX6D))
 719                 type = "Dual";
 720         else if (is_cpu_type(MXC_CPU_MX6DL))
 721                 type = "Dual-Lite";
 722         else if (is_cpu_type(MXC_CPU_MX6SOLO))
 723                 type = "Solo";
 724
 725         printf("Board: conga-QMX6 %s\n", type);
 726
 727         return 0;
 728 }
 729
 730 #ifdef CONFIG_MXC_SPI
 731 int board_spi_cs_gpio(unsigned bus, unsigned cs)
 732 {
 733         return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(3, 19)) : -EINVAL;
 734 }
 735 #endif
 736
 737 #ifdef CONFIG_CMD_BMODE
 738 static const struct boot_mode board_boot_modes[] = {
 739         /* 4 bit bus width */
 740         {"mmc0",        MAKE_CFGVAL(0x50, 0x20, 0x00, 0x00)},
 741         {"mmc1",        MAKE_CFGVAL(0x50, 0x38, 0x00, 0x00)},
 742         {NULL,          0},
 743 };
 744 #endif
 745
 746 int misc_init_r(void)
 747 {
 748 #ifdef CONFIG_CMD_BMODE
 749         add_board_boot_modes(board_boot_modes);
 750 #endif
 751         return 0;
 752 }
 753
 754 int board_late_init(void)
 755 {
 756 #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
 757         if (is_mx6dq())
 758                 env_set("board_rev", "MX6Q");
 759         else
 760                 env_set("board_rev", "MX6DL");
 761 #endif
 762
 763         return 0;
 764 }
 765
 766 #ifdef CONFIG_SPL_BUILD
 767 #include <asm/arch/mx6-ddr.h>
 768 #include <spl.h>
 769 #include <linux/libfdt.h>
 770 #include <spi_flash.h>
 771 #include <spi.h>
 772
 773 const struct mx6dq_iomux_ddr_regs mx6q_ddr_ioregs = {
 774         .dram_sdclk_0 =  0x00000030,
 775         .dram_sdclk_1 =  0x00000030,
 776         .dram_cas =  0x00000030,
 777         .dram_ras =  0x00000030,
 778         .dram_reset =  0x00000030,
 779         .dram_sdcke0 =  0x00003000,
 780         .dram_sdcke1 =  0x00003000,
 781         .dram_sdba2 =  0x00000000,
 782         .dram_sdodt0 =  0x00000030,
 783         .dram_sdodt1 =  0x00000030,
 784         .dram_sdqs0 =  0x00000030,
 785         .dram_sdqs1 =  0x00000030,
 786         .dram_sdqs2 =  0x00000030,
 787         .dram_sdqs3 =  0x00000030,
 788         .dram_sdqs4 =  0x00000030,
 789         .dram_sdqs5 =  0x00000030,
 790         .dram_sdqs6 =  0x00000030,
 791         .dram_sdqs7 =  0x00000030,
 792         .dram_dqm0 =  0x00000030,
 793         .dram_dqm1 =  0x00000030,
 794         .dram_dqm2 =  0x00000030,
 795         .dram_dqm3 =  0x00000030,
 796         .dram_dqm4 =  0x00000030,
 797         .dram_dqm5 =  0x00000030,
 798         .dram_dqm6 =  0x00000030,
 799         .dram_dqm7 =  0x00000030,
 800 };
 801
 802 static const struct mx6sdl_iomux_ddr_regs mx6dl_ddr_ioregs = {
 803         .dram_sdclk_0 = 0x00000030,
 804         .dram_sdclk_1 = 0x00000030,
 805         .dram_cas =     0x00000030,
 806         .dram_ras =     0x00000030,
 807         .dram_reset =   0x00000030,
 808         .dram_sdcke0 =  0x00003000,
 809         .dram_sdcke1 =  0x00003000,
 810         .dram_sdba2 =   0x00000000,
 811         .dram_sdodt0 =  0x00000030,
 812         .dram_sdodt1 =  0x00000030,
 813         .dram_sdqs0 =   0x00000030,
 814         .dram_sdqs1 =   0x00000030,
 815         .dram_sdqs2 =   0x00000030,
 816         .dram_sdqs3 =   0x00000030,
 817         .dram_sdqs4 =   0x00000030,
 818         .dram_sdqs5 =   0x00000030,
 819         .dram_sdqs6 =   0x00000030,
 820         .dram_sdqs7 =   0x00000030,
 821         .dram_dqm0 =    0x00000030,
 822         .dram_dqm1 =    0x00000030,
 823         .dram_dqm2 =    0x00000030,
 824         .dram_dqm3 =    0x00000030,
 825         .dram_dqm4 =    0x00000030,
 826         .dram_dqm5 =    0x00000030,
 827         .dram_dqm6 =    0x00000030,
 828         .dram_dqm7 =    0x00000030,
 829 };
 830
 831 const struct mx6dq_iomux_grp_regs mx6q_grp_ioregs = {
 832         .grp_ddr_type =  0x000C0000,
 833         .grp_ddrmode_ctl =  0x00020000,
 834         .grp_ddrpke =  0x00000000,
 835         .grp_addds =  0x00000030,
 836         .grp_ctlds =  0x00000030,
 837         .grp_ddrmode =  0x00020000,
 838         .grp_b0ds =  0x00000030,
 839         .grp_b1ds =  0x00000030,
 840         .grp_b2ds =  0x00000030,
 841         .grp_b3ds =  0x00000030,
 842         .grp_b4ds =  0x00000030,
 843         .grp_b5ds =  0x00000030,
 844         .grp_b6ds =  0x00000030,
 845         .grp_b7ds =  0x00000030,
 846 };
 847
 848 static const struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
 849         .grp_ddr_type = 0x000c0000,
 850         .grp_ddrmode_ctl = 0x00020000,
 851         .grp_ddrpke = 0x00000000,
 852         .grp_addds = 0x00000030,
 853         .grp_ctlds = 0x00000030,
 854         .grp_ddrmode = 0x00020000,
 855         .grp_b0ds = 0x00000030,
 856         .grp_b1ds = 0x00000030,
 857         .grp_b2ds = 0x00000030,
 858         .grp_b3ds = 0x00000030,
 859         .grp_b4ds = 0x00000030,
 860         .grp_b5ds = 0x00000030,
 861         .grp_b6ds = 0x00000030,
 862         .grp_b7ds = 0x00000030,
 863 };
 864
 865 const struct mx6_mmdc_calibration mx6q_mmcd_calib = {
 866         .p0_mpwldectrl0 =  0x0016001A,
 867         .p0_mpwldectrl1 =  0x0023001C,
 868         .p1_mpwldectrl0 =  0x0028003A,
 869         .p1_mpwldectrl1 =  0x001F002C,
 870         .p0_mpdgctrl0 =  0x43440354,
 871         .p0_mpdgctrl1 =  0x033C033C,
 872         .p1_mpdgctrl0 =  0x43300368,
 873         .p1_mpdgctrl1 =  0x03500330,
 874         .p0_mprddlctl =  0x3228242E,
 875         .p1_mprddlctl =  0x2C2C2636,
 876         .p0_mpwrdlctl =  0x36323A38,
 877         .p1_mpwrdlctl =  0x42324440,
 878 };
 879
 880 const struct mx6_mmdc_calibration mx6q_2g_mmcd_calib = {
 881         .p0_mpwldectrl0 =  0x00080016,
 882         .p0_mpwldectrl1 =  0x001D0016,
 883         .p1_mpwldectrl0 =  0x0018002C,
 884         .p1_mpwldectrl1 =  0x000D001D,
 885         .p0_mpdgctrl0 =    0x43200334,
 886         .p0_mpdgctrl1 =    0x0320031C,
 887         .p1_mpdgctrl0 =    0x0344034C,
 888         .p1_mpdgctrl1 =    0x03380314,
 889         .p0_mprddlctl =    0x3E36383A,
 890         .p1_mprddlctl =    0x38363240,
 891         .p0_mpwrdlctl =    0x36364238,
 892         .p1_mpwrdlctl =    0x4230423E,
 893 };
 894
 895 static const struct mx6_mmdc_calibration mx6s_mmcd_calib = {
 896         .p0_mpwldectrl0 =  0x00480049,
 897         .p0_mpwldectrl1 =  0x00410044,
 898         .p0_mpdgctrl0 =    0x42480248,
 899         .p0_mpdgctrl1 =    0x023C023C,
 900         .p0_mprddlctl =    0x40424644,
 901         .p0_mpwrdlctl =    0x34323034,
 902 };
 903
 904 const struct mx6_mmdc_calibration mx6dl_mmcd_calib = {
 905         .p0_mpwldectrl0 =  0x0043004B,
 906         .p0_mpwldectrl1 =  0x003A003E,
 907         .p1_mpwldectrl0 =  0x0047004F,
 908         .p1_mpwldectrl1 =  0x004E0061,
 909         .p0_mpdgctrl0 =    0x42500250,
 910         .p0_mpdgctrl1 =    0x0238023C,
 911         .p1_mpdgctrl0 =    0x42640264,
 912         .p1_mpdgctrl1 =    0x02500258,
 913         .p0_mprddlctl =    0x40424846,
 914         .p1_mprddlctl =    0x46484842,
 915         .p0_mpwrdlctl =    0x38382C30,
 916         .p1_mpwrdlctl =    0x34343430,
 917 };
 918
 919 static struct mx6_ddr3_cfg mem_ddr_2g = {
 920         .mem_speed = 1600,
 921         .density = 2,
 922         .width = 16,
 923         .banks = 8,
 924         .rowaddr = 14,
 925         .coladdr = 10,
 926         .pagesz = 2,
 927         .trcd = 1310,
 928         .trcmin = 4875,
 929         .trasmin = 3500,
 930 };
 931
 932 static struct mx6_ddr3_cfg mem_ddr_4g = {
 933         .mem_speed = 1600,
 934         .density = 4,
 935         .width = 16,
 936         .banks = 8,
 937         .rowaddr = 15,
 938         .coladdr = 10,
 939         .pagesz = 2,
 940         .trcd = 1310,
 941         .trcmin = 4875,
 942         .trasmin = 3500,
 943 };
 944
 945 static void ccgr_init(void)
 946 {
 947         struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
 948
 949         writel(0x00C03F3F, &ccm->CCGR0);
 950         writel(0x0030FC03, &ccm->CCGR1);
 951         writel(0x0FFFC000, &ccm->CCGR2);
 952         writel(0x3FF00000, &ccm->CCGR3);
 953         writel(0x00FFF300, &ccm->CCGR4);
 954         writel(0x0F0000C3, &ccm->CCGR5);
 955         writel(0x000003FF, &ccm->CCGR6);
 956 }
 957
 958 /* Define a minimal structure so that the part number can be read via SPL */
 959 struct mfgdata {
 960         unsigned char tsize;
 961         /* size of checksummed part in bytes */
 962         unsigned char ckcnt;
 963         /* checksum corrected byte */
 964         unsigned char cksum;
 965         /* decimal serial number, packed BCD */
 966         unsigned char serial[6];
 967          /* part number, right justified, ASCII */
 968         unsigned char pn[16];
 969 };
 970
 971 static void conv_ascii(unsigned char *dst, unsigned char *src, int len)
 972 {
 973         int remain = len;
 974         unsigned char *sptr = src;
 975         unsigned char *dptr = dst;
 976
 977         while (remain) {
 978                 if (*sptr) {
 979                         *dptr = *sptr;
 980                         dptr++;
 981                 }
 982                 sptr++;
 983                 remain--;
 984         }
 985         *dptr = 0x0;
 986 }
 987
 988 #define CFG_MFG_ADDR_OFFSET     (spi->size - SZ_16K)
 989 static bool is_2gb(void)
 990 {
 991         struct spi_flash *spi;
 992         int ret;
 993         char buf[sizeof(struct mfgdata)];
 994         struct mfgdata *data = (struct mfgdata *)buf;
 995         unsigned char outbuf[32];
 996
 997         spi = spi_flash_probe(CONFIG_ENV_SPI_BUS,
 998                               CONFIG_ENV_SPI_CS,
 999                               CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE);
1000         ret = spi_flash_read(spi, CFG_MFG_ADDR_OFFSET, sizeof(struct mfgdata),
1001                              buf);
1002         if (ret)
1003                 return false;
1004
1005         /* Congatec Part Numbers 104 and 105 have 2GiB of RAM */
1006         conv_ascii(outbuf, data->pn, sizeof(data->pn));
1007         if (!memcmp(outbuf, "016104", 6) || !memcmp(outbuf, "016105", 6))
1008                 return true;
1009         else
1010                 return false;
1011 }
1012
1013 static void spl_dram_init(int width)
1014 {
1015         struct mx6_ddr_sysinfo sysinfo = {
1016                 /* width of data bus:0=16,1=32,2=64 */
1017                 .dsize = width / 32,
1018                 /* config for full 4GB range so that get_mem_size() works */
1019                 .cs_density = 32, /* 32Gb per CS */
1020                 /* single chip select */
1021                 .ncs = 1,
1022                 .cs1_mirror = 0,
1023                 .rtt_wr = 2,
1024                 .rtt_nom = 2,
1025                 .walat = 0,
1026                 .ralat = 5,
1027                 .mif3_mode = 3,
1028                 .bi_on = 1,
1029                 .sde_to_rst = 0x0d,
1030                 .rst_to_cke = 0x20,
1031                 .refsel = 1,    /* Refresh cycles at 32KHz */
1032                 .refr = 7,      /* 8 refresh commands per refresh cycle */
1033         };
1034
1035         if (is_cpu_type(MXC_CPU_MX6Q) && is_2gb()) {
1036                 mx6dq_dram_iocfg(width, &mx6q_ddr_ioregs, &mx6q_grp_ioregs);
1037                 mx6_dram_cfg(&sysinfo, &mx6q_2g_mmcd_calib, &mem_ddr_4g);
1038                 return;
1039         }
1040
1041         if (is_mx6dq()) {
1042                 mx6dq_dram_iocfg(width, &mx6q_ddr_ioregs, &mx6q_grp_ioregs);
1043                 mx6_dram_cfg(&sysinfo, &mx6q_mmcd_calib, &mem_ddr_2g);
1044         } else if (is_cpu_type(MXC_CPU_MX6SOLO)) {
1045                 sysinfo.walat = 1;
1046                 mx6sdl_dram_iocfg(width, &mx6dl_ddr_ioregs, &mx6sdl_grp_ioregs);
1047                 mx6_dram_cfg(&sysinfo, &mx6s_mmcd_calib, &mem_ddr_4g);
1048         } else if (is_cpu_type(MXC_CPU_MX6DL)) {
1049                 sysinfo.walat = 1;
1050                 mx6sdl_dram_iocfg(width, &mx6dl_ddr_ioregs, &mx6sdl_grp_ioregs);
1051                 mx6_dram_cfg(&sysinfo, &mx6dl_mmcd_calib, &mem_ddr_2g);
1052         }
1053 }
1054
1055 void board_init_f(ulong dummy)
1056 {
1057         /* setup AIPS and disable watchdog */
1058         arch_cpu_init();
1059
1060         ccgr_init();
1061         gpr_init();
1062
1063         /* iomux and setup of i2c */
1064         board_early_init_f();
1065
1066         /* setup GP timer */
1067         timer_init();
1068
1069         /* UART clocks enabled and gd valid - init serial console */
1070         preloader_console_init();
1071
1072         /* Needed for malloc() to work in SPL prior to board_init_r() */
1073         spl_init();
1074
1075         /* DDR initialization */
1076         if (is_cpu_type(MXC_CPU_MX6SOLO))
1077                 spl_dram_init(32);
1078         else
1079                 spl_dram_init(64);
1080
1081         /* Clear the BSS. */
1082         memset(__bss_start, 0, __bss_end - __bss_start);
1083
1084         /* load/boot image from boot device */
1085         board_init_r(NULL, 0);
1086 }
1087 #endif