board/bachmann/ot1200/ot1200_spl.c

   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * Copyright (C) 2015, Bachmann electronic GmbH
   4  */
   5
   6 #include <common.h>
   7 #include <spl.h>
   8 #include <asm/arch/mx6-ddr.h>
   9
  10 /* Configure MX6Q/DUAL mmdc DDR io registers */
  11 static struct mx6dq_iomux_ddr_regs ot1200_ddr_ioregs = {
  12         /* SDCLK[0:1], CAS, RAS, Reset: Differential input, 48ohm */
  13         .dram_sdclk_0   = 0x00000028,
  14         .dram_sdclk_1   = 0x00000028,
  15         .dram_cas       = 0x00000028,
  16         .dram_ras       = 0x00000028,
  17         .dram_reset     = 0x00000028,
  18         /* SDCKE[0:1]: 100k pull-up */
  19         .dram_sdcke0    = 0x00003000,
  20         .dram_sdcke1    = 0x00003000,
  21         /* SDBA2: pull-up disabled */
  22         .dram_sdba2         = 0x00000000,
  23         /* SDODT[0:1]: 100k pull-up, 48 ohm */
  24         .dram_sdodt0    = 0x00000028,
  25         .dram_sdodt1    = 0x00000028,
  26         /* SDQS[0:7]: Differential input, 48 ohm */
  27         .dram_sdqs0     = 0x00000028,
  28         .dram_sdqs1     = 0x00000028,
  29         .dram_sdqs2     = 0x00000028,
  30         .dram_sdqs3     = 0x00000028,
  31         .dram_sdqs4     = 0x00000028,
  32         .dram_sdqs5     = 0x00000028,
  33         .dram_sdqs6     = 0x00000028,
  34         .dram_sdqs7     = 0x00000028,
  35         /* DQM[0:7]: Differential input, 48 ohm */
  36         .dram_dqm0      = 0x00000028,
  37         .dram_dqm1      = 0x00000028,
  38         .dram_dqm2      = 0x00000028,
  39         .dram_dqm3      = 0x00000028,
  40         .dram_dqm4      = 0x00000028,
  41         .dram_dqm5      = 0x00000028,
  42         .dram_dqm6      = 0x00000028,
  43         .dram_dqm7      = 0x00000028,
  44 };
  45
  46 /* Configure MX6Q/DUAL mmdc GRP io registers */
  47 static struct mx6dq_iomux_grp_regs ot1200_grp_ioregs = {
  48         /* DDR3 */
  49         .grp_ddr_type    = 0x000c0000,
  50         .grp_ddrmode_ctl = 0x00020000,
  51         /* Disable DDR pullups */
  52         .grp_ddrpke      = 0x00000000,
  53         /* ADDR[00:16], SDBA[0:1]: 48 ohm */
  54         .grp_addds       = 0x00000028,
  55         /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 48 ohm */
  56         .grp_ctlds       = 0x00000028,
  57         /* DATA[00:63]: Differential input, 48 ohm */
  58         .grp_ddrmode     = 0x00020000,
  59         .grp_b0ds        = 0x00000028,
  60         .grp_b1ds        = 0x00000028,
  61         .grp_b2ds        = 0x00000028,
  62         .grp_b3ds        = 0x00000028,
  63         .grp_b4ds        = 0x00000028,
  64         .grp_b5ds        = 0x00000028,
  65         .grp_b6ds        = 0x00000028,
  66         .grp_b7ds        = 0x00000028,
  67 };
  68
  69 static struct mx6_ddr_sysinfo ot1200_ddr_sysinfo = {
  70         /* Width of data bus: 0=16, 1=32, 2=64 */
  71         .dsize      = 2,
  72         /* config for full 4GB range so that get_mem_size() works */
  73         .cs_density = 32, /* 32Gb per CS */
  74         /* Single chip select */
  75         .ncs        = 1,
  76         .cs1_mirror = 0,        /* war 0 */
  77         .rtt_wr     = 1,        /* DDR3_RTT_60_OHM - RTT_Wr = RZQ/4 */
  78         .rtt_nom    = 1,        /* DDR3_RTT_60_OHM - RTT_Nom = RZQ/4 */
  79         .walat      = 1,        /* Write additional latency */
  80         .ralat      = 5,        /* Read additional latency */
  81         .mif3_mode  = 3,        /* Command prediction working mode */
  82         .bi_on      = 1,        /* Bank interleaving enabled */ /* war 1 */
  83         .sde_to_rst = 0x10,     /* 14 cycles, 200us (JEDEC default) */
  84         .rst_to_cke = 0x23,     /* 33 cycles, 500us (JEDEC default) */
  85         .refsel = 1,            /* Refresh cycles at 32KHz */
  86         .refr = 7,              /* 8 refresh commands per refresh cycle */
  87 };
  88
  89 /* MT41K128M16JT-125 */
  90 static struct mx6_ddr3_cfg micron_2gib_1600 = {
  91         .mem_speed = 1600,
  92         .density   = 2,
  93         .width     = 16,
  94         .banks     = 8,
  95         .rowaddr   = 14,
  96         .coladdr   = 10,
  97         .pagesz    = 2,
  98         .trcd      = 1375,
  99         .trcmin    = 4875,
 100         .trasmin   = 3500,
 101         .SRT       = 1,
 102 };
 103
 104 static struct mx6_mmdc_calibration micron_2gib_1600_mmdc_calib = {
 105         /* write leveling calibration determine */
 106         .p0_mpwldectrl0 = 0x00260025,
 107         .p0_mpwldectrl1 = 0x00270021,
 108         .p1_mpwldectrl0 = 0x00180034,
 109         .p1_mpwldectrl1 = 0x00180024,
 110         /* Read DQS Gating calibration */
 111         .p0_mpdgctrl0   = 0x04380344,
 112         .p0_mpdgctrl1   = 0x0330032C,
 113         .p1_mpdgctrl0   = 0x0338033C,
 114         .p1_mpdgctrl1   = 0x032C0300,
 115         /* Read Calibration: DQS delay relative to DQ read access */
 116         .p0_mprddlctl   = 0x3C2E3238,
 117         .p1_mprddlctl   = 0x3A2E303C,
 118         /* Write Calibration: DQ/DM delay relative to DQS write access */
 119         .p0_mpwrdlctl   = 0x36384036,
 120         .p1_mpwrdlctl   = 0x442E4438,
 121 };
 122
 123 static void ot1200_spl_dram_init(void)
 124 {
 125         mx6dq_dram_iocfg(64, &ot1200_ddr_ioregs, &ot1200_grp_ioregs);
 126         mx6_dram_cfg(&ot1200_ddr_sysinfo, &micron_2gib_1600_mmdc_calib,
 127                      &micron_2gib_1600);
 128 }
 129
 130 /*
 131  * called from C runtime startup code (arch/arm/lib/crt0.S:_main)
 132  * - we have a stack and a place to store GD, both in SRAM
 133  * - no variable global data is available
 134  */
 135 void board_init_f(ulong dummy)
 136 {
 137         /* setup AIPS and disable watchdog */
 138         arch_cpu_init();
 139
 140         /* iomux and setup of i2c */
 141         board_early_init_f();
 142
 143         /* setup GP timer */
 144         timer_init();
 145
 146         /* UART clocks enabled and gd valid - init serial console */
 147         preloader_console_init();
 148
 149         /* configure MMDC for SDRAM width/size and per-model calibration */
 150         ot1200_spl_dram_init();
 151 }