1 U-Boot for Amlogic P212
2 =======================
4 P212 is a reference board manufactured by Amlogic with the following
7 - Amlogic S905X ARM Cortex-A53 quad-core SoC @ 1.5GHz
11 - HDMI 2.0 4K/60Hz display
16 - CVBS+Stereo Audio Jack
18 Schematics are available from Amlogic on demand.
20 Currently the u-boot port supports the following devices:
34 > export CROSS_COMPILE=aarch64-none-elf-
41 Amlogic doesn't provide sources for the firmware and for tools needed
42 to create the bootloader image, so it is necessary to obtain them from
43 the git tree published by the board vendor:
45 > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
46 > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
47 > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
48 > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
49 > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
50 > git clone https://github.com/BayLibre/u-boot.git -b n-amlogic-openlinux-20170606 amlogic-u-boot
52 > make gxl_p212_v1_defconfig
54 > export FIPDIR=$PWD/fip
56 Go back to mainline U-boot source tree then :
59 > cp $FIPDIR/gxl/bl2.bin fip/
60 > cp $FIPDIR/gxl/acs.bin fip/
61 > cp $FIPDIR/gxl/bl21.bin fip/
62 > cp $FIPDIR/gxl/bl30.bin fip/
63 > cp $FIPDIR/gxl/bl301.bin fip/
64 > cp $FIPDIR/gxl/bl31.img fip/
65 > cp u-boot.bin fip/bl33.bin
67 > $FIPDIR/blx_fix.sh \
76 > $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0
78 > $FIPDIR/blx_fix.sh \
87 > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin
88 > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img
89 > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin
90 > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig
91 > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \
92 --output fip/u-boot.bin \
93 --bl2 fip/bl2.n.bin.sig \
94 --bl30 fip/bl30_new.bin.enc \
95 --bl31 fip/bl31.img.enc \
96 --bl33 fip/bl33.bin.enc
98 and then write the image to SD with:
100 > DEV=/dev/your_sd_device
101 > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
102 > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444