target/linux/ath79/dts/qca9563_rosinson_wr818.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca956x.dtsi"
   8
   9 / {
  10         model = "ROSINSON WR818";
  11         compatible = "rosinson,wr818", "qca,qca9563";
  12
  13         chosen {
  14                 bootargs = "console=ttyS0,115200n8";
  15         };
  16
  17         aliases {
  18                 led-boot = &led_system;
  19                 led-failsafe = &led_system;
  20                 led-running = &led_system;
  21                 led-upgrade = &led_system;
  22         };
  23
  24         leds {
  25                 compatible = "gpio-leds";
  26
  27                 led_system: system {
  28                         label = "wr818:red:system";
  29                         gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
  30                 };
  31
  32                 wifi_2g {
  33                         label = "wr818:red:wifi2g";
  34                         gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
  35                         linux,default-trigger = "phy0tpt";
  36                 };
  37         };
  38
  39         keys {
  40                 compatible = "gpio-keys";
  41
  42                 reset {
  43                         label = "reset";
  44                         linux,code = <KEY_RESTART>;
  45                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  46                         debounce-interval = <60>;
  47                 };
  48         };
  49 };
  50
  51 &uart {
  52         status = "okay";
  53 };
  54
  55 &gpio {
  56         status = "okay";
  57 };
  58
  59 &spi {
  60         status = "okay";
  61
  62         num-cs = <1>;
  63
  64         flash@0 {
  65                 compatible = "jedec,spi-nor";
  66                 reg = <0>;
  67                 spi-max-frequency = <25000000>;
  68
  69                 partitions {
  70                         compatible = "fixed-partitions";
  71                         #address-cells = <1>;
  72                         #size-cells = <1>;
  73
  74                         partition@0 {
  75                                 label = "u-boot";
  76                                 reg = <0x000000 0x040000>;
  77                                 read-only;
  78                         };
  79
  80                         partition@40000 {
  81                                 label = "u-boot-env";
  82                                 reg = <0x040000 0x010000>;
  83                                 read-only;
  84                         };
  85
  86                         info: partition@50000 {
  87                                 label = "factory";
  88                                 reg = <0x050000 0x010000>;
  89                                 read-only;
  90                         };
  91
  92                         partition@60000 {
  93                                 compatible = "denx,uimage";
  94                                 label = "firmware";
  95                                 reg = <0x060000 0xf80000>;
  96                         };
  97
  98                         art: partition@ff0000 {
  99                                 label = "art";
 100                                 reg = <0xff0000 0x010000>;
 101                                 read-only;
 102                         };
 103                 };
 104         };
 105 };
 106
 107 &mdio0 {
 108         status = "okay";
 109
 110         phy-mask = <0>;
 111         phy0: ethernet-phy@0 {
 112                 reg = <0>;
 113                 phy-mode = "sgmii";
 114
 115                 qca,ar8327-initvals = <
 116                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
 117                         0x7c 0x0000007e /* PORT0_STATUS */
 118                 >;
 119         };
 120 };
 121
 122 &eth0 {
 123         status = "okay";
 124
 125         mtd-mac-address = <&info 0x0>;
 126         phy-mode = "sgmii";
 127         phy-handle = <&phy0>;
 128 };
 129
 130 &wmac {
 131         status = "okay";
 132
 133         mtd-cal-data = <&art 0x1000>;
 134 };
 135
 136 &usb_phy0 {
 137         status = "okay";
 138 };
 139
 140 &usb0 {
 141         #address-cells = <1>;
 142         #size-cells = <0>;
 143         status = "okay";
 144
 145         port@1 {
 146                 reg = <1>;
 147                 #trigger-source-cells = <0>;
 148         };
 149 };
 150
 151 &usb_phy1 {
 152         status = "okay";
 153 };
 154
 155 &usb1 {
 156         #address-cells = <1>;
 157         #size-cells = <0>;
 158         status = "okay";
 159
 160         port@2 {
 161                 reg = <2>;
 162                 #trigger-source-cells = <0>;
 163         };
 164 };