target/linux/ath79/dts/qca9563_phicomm_k2t.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca956x.dtsi"
   8
   9 / {
  10         model = "Phicomm K2T";
  11         compatible = "phicomm,k2t", "qca,qca9563";
  12
  13         aliases {
  14                 led-boot = &led_status_red;
  15                 led-failsafe = &led_status_red;
  16                 led-running = &led_status_red;
  17                 led-upgrade = &led_status_red;
  18         };
  19
  20         chosen {
  21                 bootargs = "console=ttyS0,115200n8";
  22         };
  23
  24         leds {
  25                 compatible = "gpio-leds";
  26
  27                 status_blue {
  28                         label = "phicomm:blue:status";
  29                         gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
  30                 };
  31
  32                 led_status_red: status_red {
  33                         label = "phicomm:red:status";
  34                         gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
  35                 };
  36
  37                 status_yellow {
  38                         label = "phicomm:yellow:status";
  39                         gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
  40                 };
  41         };
  42
  43         keys {
  44                 compatible = "gpio-keys";
  45
  46                 reset {
  47                         linux,code = <KEY_RESTART>;
  48                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  49                         debounce-interval = <60>;
  50                 };
  51         };
  52 };
  53
  54 &uart {
  55         status = "okay";
  56 };
  57
  58 &gpio {
  59         status = "okay";
  60 };
  61
  62 &pcie {
  63         status = "okay";
  64 };
  65
  66 &spi {
  67         num-cs = <1>;
  68
  69         status = "okay";
  70
  71         flash@0 {
  72                 compatible = "jedec,spi-nor";
  73                 reg = <0>;
  74                 spi-max-frequency = <25000000>;
  75
  76                 partitions {
  77                         compatible = "fixed-partitions";
  78                         #address-cells = <1>;
  79                         #size-cells = <1>;
  80
  81                         partition@0 {
  82                                 label = "u-boot";
  83                                 reg = <0x000000 0x30000>;
  84                                 read-only;
  85                         };
  86
  87                         partition@30000 {
  88                                 label = "config";
  89                                 reg = <0x030000 0x10000>;
  90                                 read-only;
  91                         };
  92
  93                         partition@40000 {
  94                                 label = "permanent";
  95                                 reg = <0x040000 0x50000>;
  96                                 read-only;
  97                         };
  98
  99                         partition@90000 {
 100                                 compatible = "denx,uimage";
 101                                 label = "firmware";
 102                                 reg = <0x090000 0xf60000>;
 103                         };
 104
 105                         art: partition@ff0000 {
 106                                 label = "art";
 107                                 reg = <0xff0000 0x010000>;
 108                                 read-only;
 109                         };
 110                 };
 111         };
 112 };
 113
 114 &mdio0 {
 115         status = "okay";
 116
 117         phy-mask = <0>;
 118
 119         phy0: ethernet-phy@0 {
 120                 reg = <0>;
 121                 phy-mode = "sgmii";
 122
 123                 qca,ar8327-initvals = <
 124                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
 125                         0x10 0x81000080 /* POWER_ON_STRIP */
 126                         0x50 0xcc35cc35 /* LED_CTRL0 */
 127                         0x54 0xcb37cb37 /* LED_CTRL1 */
 128                         0x58 0x00000000 /* LED_CTRL2 */
 129                         0x5c 0x00f3cf00 /* LED_CTRL3 */
 130                         0x7c 0x0000007e /* PORT0_STATUS */
 131                         >;
 132         };
 133 };
 134
 135 &eth0 {
 136         status = "okay";
 137
 138         pll-data = <0x03000101 0x00000101 0x00001919>;
 139
 140         phy-mode = "sgmii";
 141         phy-handle = <&phy0>;
 142 };
 143
 144 &wmac {
 145         status = "okay";
 146         mtd-cal-data = <&art 0x1000>;
 147 };