target/linux/ath79/dts/qca9563_glinet_gl-ar750s.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include <dt-bindings/gpio/gpio.h>
   4 #include <dt-bindings/input/input.h>
   5
   6 #include "qca956x.dtsi"
   7
   8 / {
   9         compatible = "glinet,gl-ar750s", "qca,qca9563";
  10         model = "GL.iNet GL-AR750S";
  11
  12         chosen {
  13                 bootargs = "console=ttyS0,115200n8";
  14         };
  15
  16         aliases {
  17                 led-boot = &led_power;
  18                 led-failsafe = &led_power;
  19                 led-running = &led_power;
  20                 led-upgrade = &led_power;
  21                 label-mac-device = &eth0;
  22         };
  23
  24         keys {
  25                 compatible = "gpio-keys";
  26
  27                 pinctrl-names = "default";
  28                 pinctrl-0 = <&jtag_disable_pins>;
  29
  30                 reset {
  31                         label = "reset";
  32                         linux,code = <KEY_RESTART>;
  33                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  34                 };
  35
  36                 mode {
  37                         label = "mode";
  38                         linux,code = <BTN_0>;
  39                         linux,input-type = <EV_SW>;
  40                         gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
  41                 };
  42         };
  43
  44         leds {
  45                 compatible = "gpio-leds";
  46
  47                 led_power: power {
  48                         label = "gl-ar750s:green:power";
  49                         gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
  50                         default-state = "keep";
  51                 };
  52
  53                 led_wlan2g: wlan2g {
  54                         label = "gl-ar750s:green:wlan2g";
  55                         gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
  56                         linux,default-trigger = "phy1tpt";
  57                 };
  58
  59                 led_wlan5g: wlan5g {
  60                         label = "gl-ar750s:green:wlan5g";
  61                         gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
  62                         linux,default-trigger = "phy0tpt";
  63                 };
  64         };
  65
  66         i2c: i2c {
  67                 compatible = "i2c-gpio";
  68
  69                 sda-gpios = <&gpio  5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
  70                 scl-gpios = <&gpio 21 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
  71         };
  72 };
  73
  74 &spi {
  75         status = "okay";
  76
  77         num-cs = <2>;
  78
  79         flash_nor: flash@0 {
  80                 compatible = "jedec,spi-nor";
  81                 reg = <0>;
  82                 spi-max-frequency = <25000000>;
  83
  84                 nor_partitions: partitions {
  85                         compatible = "fixed-partitions";
  86                         #address-cells = <1>;
  87                         #size-cells = <1>;
  88
  89                         partition@0 {
  90                                 label = "u-boot";
  91                                 reg = <0x000000 0x040000>;
  92                                 read-only;
  93                         };
  94
  95                         partition@40000 {
  96                                 label = "u-boot-env";
  97                                 reg = <0x040000 0x010000>;
  98                         };
  99
 100                         art: partition@50000 {
 101                                 label = "art";
 102                                 reg = <0x050000 0x010000>;
 103                                 read-only;
 104                         };
 105
 106                         nor_firmware: partition@60000 {
 107                                 label = "nor_firmware";
 108                                 reg = <0x060000 0xfa0000>;
 109                         };
 110
 111                         nor_kernel: partition_alt@60000 {
 112                                 label = "nor_kernel";
 113                                 reg = <0x060000 0x400000>;
 114                         };
 115
 116                         nor_reserved: parition_alt@460000 {
 117                                 label = "nor_reserved";
 118                                 reg = <0x460000 0xba0000>;
 119                         };
 120                 };
 121         };
 122
 123         flash_nand: flash@1 {
 124                 compatible = "spi-nand";
 125                 reg = <1>;
 126                 spi-max-frequency = <25000000>;
 127
 128                 nand_partitions: partitions {
 129                         compatible = "fixed-partitions";
 130                         #address-cells = <1>;
 131                         #size-cells = <1>;
 132
 133                         nand_ubi: partition@0 {
 134                                 label = "nand_ubi";
 135                                 reg = <0x000000 0x8000000>;
 136                         };
 137                 };
 138         };
 139 };
 140
 141 &eth0 {
 142         status = "okay";
 143
 144         phy-handle = <&phy0>;
 145         mtd-mac-address = <&art 0x0>;
 146 };
 147
 148 &gpio {
 149         usb_vbus {
 150                 gpio-hog;
 151                 gpios = <7 GPIO_ACTIVE_HIGH>;
 152                 output-high;
 153                 line-name = "usb-vbus";
 154         };
 155 };
 156
 157 &mdio0 {
 158         status = "okay";
 159
 160         phy-mask = <0>;
 161
 162         phy0: ethernet-phy@0 {
 163                 reg = <0>;
 164                 phy-mode = "sgmii";
 165                 qca,ar8327-initvals = <
 166                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
 167                         0x7c 0x0000007e /* PORT0_STATUS */
 168                 >;
 169         };
 170 };
 171
 172 &pcie {
 173         status = "okay";
 174 };
 175
 176 &uart {
 177         status = "okay";
 178 };
 179
 180 &usb0 {
 181         status = "okay";
 182 };
 183
 184 &usb1 {
 185         status = "okay";
 186 };
 187
 188 &usb_phy0 {
 189         status = "okay";
 190 };
 191
 192 &usb_phy1 {
 193         status = "okay";
 194 };
 195
 196 &wmac {
 197         status = "okay";
 198
 199         mtd-cal-data = <&art 0x1000>;
 200 };