target/linux/ath79/dts/qca9563_dlink_dir-842-c.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include <dt-bindings/gpio/gpio.h>
   4 #include <dt-bindings/input/input.h>
   5
   6 #include "qca956x.dtsi"
   7
   8 / {
   9         chosen {
  10                 bootargs = "console=ttyS0,115200n8";
  11         };
  12
  13         keys {
  14                 compatible = "gpio-keys";
  15
  16                 wps {
  17                         linux,code = <KEY_WPS_BUTTON>;
  18                         gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
  19                         debounce-interval = <60>;
  20                 };
  21
  22                 reset {
  23                         linux,code = <KEY_RESTART>;
  24                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  25                         debounce-interval = <60>;
  26                 };
  27         };
  28 };
  29
  30 &uart {
  31         status = "okay";
  32 };
  33
  34 &pcie {
  35         status = "okay";
  36 };
  37
  38 &spi {
  39         status = "okay";
  40
  41         num-cs = <1>;
  42
  43         flash@0 {
  44                 compatible = "jedec,spi-nor";
  45                 reg = <0>;
  46                 spi-max-frequency = <50000000>;
  47
  48                 partitions {
  49                         compatible = "fixed-partitions";
  50                         #address-cells = <1>;
  51                         #size-cells = <1>;
  52
  53                         partition@0 {
  54                                 label = "u-boot";
  55                                 reg = <0x000000 0x40000>;
  56                                 read-only;
  57                         };
  58
  59                         partition@40000 {
  60                                 label = "u-boot-env";
  61                                 reg = <0x040000 0x10000>;
  62                                 read-only;
  63                         };
  64
  65                         partition@50000 {
  66                                 label = "devdata";
  67                                 reg = <0x050000 0x10000>;
  68                                 read-only;
  69                         };
  70
  71                         partition@60000 {
  72                                 label = "devconf";
  73                                 reg = <0x060000 0x10000>;
  74                                 read-only;
  75                         };
  76
  77                         partition@70000 {
  78                                 label = "misc";
  79                                 reg = <0x070000 0x10000>;
  80                                 read-only;
  81                         };
  82
  83                         partition@80000 {
  84                                 compatible = "seama";
  85                                 label = "firmware";
  86                                 reg = <0x080000 0xf50000>;
  87                         };
  88
  89                         art: partition@fd0000 {
  90                                 label = "art";
  91                                 reg = <0xfd0000 0x010000>;
  92                                 read-only;
  93                         };
  94
  95                         partition@fe0000 {
  96                                 label = "reserved";
  97                                 reg = <0xfe0000 0x20000>;
  98                                 read-only;
  99                         };
 100                 };
 101         };
 102 };
 103
 104 &mdio0 {
 105         status = "okay";
 106
 107         phy-mask = <0>;
 108
 109         phy0: ethernet-phy@0 {
 110                 reg = <0>;
 111                 qca,mib-poll-interval = <500>;
 112                 reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
 113
 114                 qca,ar8327-initvals = <
 115                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
 116                         0x10 0x81000080 /* POWER_ON_STRIP */
 117                         0x50 0xcc35cc35 /* LED_CTRL0 */
 118                         0x54 0xcb37cb37 /* LED_CTRL1 */
 119                         0x58 0x00000000 /* LED_CTRL2 */
 120                         0x5c 0x00f3cf00 /* LED_CTRL3 */
 121                         0x7c 0x0000007e /* PORT0_STATUS */
 122                         >;
 123         };
 124 };
 125
 126 &eth0 {
 127         status = "okay";
 128
 129         pll-data = <0x03000101 0x00000101 0x00001919>;
 130
 131         phy-mode = "sgmii";
 132         phy-handle = <&phy0>;
 133 };
 134
 135 &wmac {
 136         status = "okay";
 137
 138         qca,no-eeprom;
 139 };