target/linux/ath79/dts/qca9563_dlink_dir-842-c.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include <dt-bindings/gpio/gpio.h>
   4 #include <dt-bindings/input/input.h>
   5
   6 #include "qca956x.dtsi"
   7
   8 / {
   9         keys {
  10                 compatible = "gpio-keys";
  11
  12                 wps {
  13                         linux,code = <KEY_WPS_BUTTON>;
  14                         gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
  15                         debounce-interval = <60>;
  16                 };
  17
  18                 reset {
  19                         linux,code = <KEY_RESTART>;
  20                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  21                         debounce-interval = <60>;
  22                 };
  23         };
  24 };
  25
  26 &uart {
  27         status = "okay";
  28 };
  29
  30 &pcie {
  31         status = "okay";
  32 };
  33
  34 &spi {
  35         status = "okay";
  36
  37         num-cs = <1>;
  38
  39         flash@0 {
  40                 compatible = "jedec,spi-nor";
  41                 reg = <0>;
  42                 spi-max-frequency = <50000000>;
  43
  44                 partitions {
  45                         compatible = "fixed-partitions";
  46                         #address-cells = <1>;
  47                         #size-cells = <1>;
  48
  49                         partition@0 {
  50                                 label = "u-boot";
  51                                 reg = <0x000000 0x40000>;
  52                                 read-only;
  53                         };
  54
  55                         partition@40000 {
  56                                 label = "u-boot-env";
  57                                 reg = <0x040000 0x10000>;
  58                                 read-only;
  59                         };
  60
  61                         partition@50000 {
  62                                 label = "devdata";
  63                                 reg = <0x050000 0x10000>;
  64                                 read-only;
  65                         };
  66
  67                         partition@60000 {
  68                                 label = "devconf";
  69                                 reg = <0x060000 0x10000>;
  70                                 read-only;
  71                         };
  72
  73                         partition@70000 {
  74                                 label = "misc";
  75                                 reg = <0x070000 0x10000>;
  76                                 read-only;
  77                         };
  78
  79                         partition@80000 {
  80                                 compatible = "seama";
  81                                 label = "firmware";
  82                                 reg = <0x080000 0xf50000>;
  83                         };
  84
  85                         art: partition@fd0000 {
  86                                 label = "art";
  87                                 reg = <0xfd0000 0x010000>;
  88                                 read-only;
  89                         };
  90
  91                         partition@fe0000 {
  92                                 label = "reserved";
  93                                 reg = <0xfe0000 0x20000>;
  94                                 read-only;
  95                         };
  96                 };
  97         };
  98 };
  99
 100 &mdio0 {
 101         status = "okay";
 102
 103         phy-mask = <0>;
 104
 105         phy0: ethernet-phy@0 {
 106                 reg = <0>;
 107                 qca,mib-poll-interval = <500>;
 108                 reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
 109
 110                 qca,ar8327-initvals = <
 111                         0x04 0x00080080 /* PORT0 PAD MODE CTRL */
 112                         0x10 0x81000080 /* POWER_ON_STRIP */
 113                         0x50 0xcc35cc35 /* LED_CTRL0 */
 114                         0x54 0xcb37cb37 /* LED_CTRL1 */
 115                         0x58 0x00000000 /* LED_CTRL2 */
 116                         0x5c 0x00f3cf00 /* LED_CTRL3 */
 117                         0x7c 0x0000007e /* PORT0_STATUS */
 118                         >;
 119         };
 120 };
 121
 122 &eth0 {
 123         status = "okay";
 124
 125         pll-data = <0x03000101 0x00000101 0x00001919>;
 126
 127         phy-mode = "sgmii";
 128         phy-handle = <&phy0>;
 129 };
 130
 131 &wmac {
 132         status = "okay";
 133
 134         qca,no-eeprom;
 135 };