target/linux/ath79/dts/qca9558_mikrotik_routerboard-922uags-5hpacd.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca955x.dtsi"
   8
   9 / {
  10         compatible = "mikrotik,routerboard-922uags-5hpacd", "qca,qca9558";
  11         model = "MikroTik RouterBOARD 922UAGS-5HPacD";
  12
  13         aliases {
  14                 led-boot = &led_user;
  15                 led-failsafe = &led_user;
  16                 led-upgrade = &led_user;
  17                 serial0 = &uart;
  18         };
  19
  20         leds {
  21                 compatible = "gpio-leds";
  22
  23                 led_user: user {
  24                         label = "mikrotik:green:user";
  25                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  26                 };
  27         };
  28
  29         ath10k-leds {
  30                 compatible = "gpio-leds";
  31
  32                 wlan5g {
  33                         label = "mikrotik:green:wlan5g";
  34                         gpios = <&ath10k 0 GPIO_ACTIVE_LOW>;
  35                         linux,default-trigger = "phy0tpt";
  36                 };
  37         };
  38
  39         keys {
  40                 compatible = "gpio-keys";
  41
  42                 reset {
  43                         label = "reset";
  44                         linux,code = <KEY_RESTART>;
  45                         gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
  46                         debounce-interval = <60>;
  47                 };
  48         };
  49
  50         gpio-export {
  51                 compatible = "gpio-export";
  52
  53                 gpio_usb_power {
  54                         gpio-export,name = "mikrotik:power:usb";
  55                         gpio-export,output = <0>;
  56                         gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
  57                 };
  58
  59                 gpio_nand_power {
  60                         gpio-export,name = "mikrotik:power:nand";
  61                         gpio-export,output = <0>;
  62                         gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
  63                 };
  64         };
  65 };
  66
  67 &mdio0 {
  68         status = "okay";
  69
  70         phy4: ethernet-phy@4 {
  71                 reg = <4>;
  72         };
  73 };
  74
  75 &eth0 {
  76         status = "okay";
  77
  78         phy-handle = <&phy4>;
  79         pll-data = <0x8f000000 0xa0000101 0xa0001313>;
  80
  81         gmac-config {
  82                 device = <&gmac>;
  83                 rgmii-enabled = <1>;
  84         };
  85 };
  86
  87 &spi {
  88         status = "okay";
  89
  90         flash@0 {
  91                 compatible = "jedec,spi-nor";
  92                 reg = <0>;
  93                 spi-max-frequency = <25000000>;
  94
  95                 partitions {
  96                         compatible = "mikrotik,routerboot-partitions";
  97                         #address-cells = <1>;
  98                         #size-cells = <1>;
  99
 100                         partition@0 {
 101                                 label = "routerboot";
 102                                 reg = <0x0 0x0>;
 103                                 read-only;
 104                         };
 105
 106                         hard_config: hard_config {
 107                                 read-only;
 108                         };
 109
 110                         bios {
 111                                 read-only;
 112                         };
 113
 114                         soft_config {
 115                         };
 116                 };
 117         };
 118 };
 119
 120 &nand {
 121         status = "okay";
 122
 123         nand-ecc-mode = "soft";
 124         qca,nand-swap-dma;
 125         qca,nand-scan-fixup;
 126
 127         partitions {
 128                 compatible = "fixed-partitions";
 129                 #size-cells = <1>;
 130
 131                 partition@0 {
 132                         label = "booter";
 133                         reg = <0x0000000 0x0040000>;
 134                         read-only;
 135                 };
 136
 137                 partition@40000 {
 138                         label = "kernel";
 139                         reg = <0x0040000 0x03c0000>;
 140                 };
 141
 142                 partition@400000 {
 143                         label = "ubi";
 144                         reg = <0x0400000 0x7c00000>;
 145                 };
 146         };
 147 };
 148
 149 &uart {
 150         status = "okay";
 151 };
 152
 153 &pcie0 {
 154         status = "okay";
 155
 156         ath10k: wifi@0,0 {
 157                 compatible = "qcom,ath10k";
 158                 reg = <0 0 0 0 0>;
 159                 #gpio-cells = <2>;
 160                 gpio-controller;
 161         };
 162 };
 163
 164 &pcie1 {
 165         status = "okay";
 166 };
 167
 168 &usb0 {
 169         status = "okay";
 170 };
 171
 172 &usb_phy0 {
 173         status = "okay";
 174 };