target/linux/ath79/dts/qca9531_tplink_archer-d50-v1.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca953x.dtsi"
   8
   9 / {
  10         compatible = "tplink,archer-d50-v1", "qca,qca9531";
  11         model = "TP-Link Archer D50 v1";
  12
  13         aliases {
  14                 led-boot = &led_system;
  15                 led-failsafe = &led_system;
  16                 led-running = &led_system;
  17                 led-upgrade = &led_system;
  18                 label-mac-device = &wmac;
  19         };
  20
  21         chosen {
  22                 bootargs = "console=ttyS0,115200n8";
  23         };
  24
  25         leds {
  26                 compatible = "gpio-leds";
  27
  28                 wlan2g {
  29                         label = "tp-link:white:wlan2g";
  30                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  31                         linux,default-trigger = "phy0tpt";
  32                 };
  33
  34                 wlan5g {
  35                         label = "tp-link:white:wlan5g";
  36                         gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
  37                         linux,default-trigger = "phy1tpt";
  38                 };
  39
  40                 qss {
  41                         label = "tp-link:white:qss";
  42                         gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
  43                 };
  44
  45                 wan {
  46                         label = "tp-link:white:wan";
  47                         gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
  48                 };
  49
  50                 lan {
  51                         label = "tp-link:white:lan";
  52                         gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
  53                 };
  54
  55                 usb {
  56                         label = "tp-link:white:usb";
  57                         gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
  58                         trigger-sources = <&hub_port0>;
  59                         linux,default-trigger = "usbport";
  60                 };
  61
  62                 internet {
  63                         label = "tp-link:white:internet";
  64                         gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
  65                 };
  66
  67                 led_system: system {
  68                         label = "tp-link:white:system";
  69                         gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
  70                         default-state = "on";
  71                 };
  72         };
  73
  74         keys {
  75                 compatible = "gpio-keys";
  76
  77                 reset {
  78                         label = "Reset button";
  79                         linux,code = <KEY_RESTART>;
  80                         gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
  81                 };
  82
  83                 rfkill {
  84                         label = "RFKILL button";
  85                         linux,code = <KEY_RFKILL>;
  86                         gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
  87                 };
  88
  89                 wps {
  90                         label = "WPS button";
  91                         linux,code = <KEY_WPS_BUTTON>;
  92                         gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
  93                 };
  94         };
  95 };
  96
  97 &uart {
  98         status = "okay";
  99 };
 100
 101 &spi {
 102         status = "okay";
 103
 104         flash@0 {
 105                 compatible = "jedec,spi-nor";
 106                 reg = <0>;
 107                 spi-max-frequency = <10000000>;
 108
 109                 partitions {
 110                         compatible = "fixed-partitions";
 111                         #address-cells = <1>;
 112                         #size-cells = <1>;
 113
 114                         partition@0 {
 115                                 label = "u-boot";
 116                                 reg = <0x000000 0x020000>;
 117                                 read-only;
 118                         };
 119
 120                         partition@20000 {
 121                                 compatible = "tplink,firmware";
 122                                 label = "firmware";
 123                                 reg = <0x020000 0x7a0000>;
 124                         };
 125
 126                         partition@7c0000 {
 127                                 label = "config";
 128                                 reg = <0x7c0000 0x010000>;
 129                                 read-only;
 130                         };
 131
 132                         romfile: partition@7d0000 {
 133                                 label = "romfile";
 134                                 reg = <0x7d0000 0x010000>;
 135                                 read-only;
 136                         };
 137
 138                         partition@7e0000 {
 139                                 label = "rom";
 140                                 reg = <0x7e0000 0x010000>;
 141                                 read-only;
 142                         };
 143
 144                         art: partition@7f0000 {
 145                                 label = "art";
 146                                 reg = <0x7f0000 0x010000>;
 147                                 read-only;
 148                         };
 149                 };
 150         };
 151 };
 152
 153 &eth1 {
 154         mtd-mac-address = <&romfile 0xf100>;
 155 };
 156
 157 &eth0 {
 158         status = "okay";
 159
 160         phy-handle = <&swphy4>;
 161
 162         mtd-mac-address = <&romfile 0xf100>;
 163         mtd-mac-address-increment = <1>;
 164 };
 165
 166 &wmac {
 167         status = "okay";
 168
 169         mtd-cal-data = <&art 0x1000>;
 170         mtd-mac-address = <&romfile 0xf100>;
 171 };
 172
 173 &pcie0 {
 174         status = "okay";
 175
 176         wifi@0,0 {
 177                 compatible = "pci168c,003c";
 178                 reg = <0x0000 0 0 0 0>;
 179         };
 180 };
 181
 182 &usb_phy {
 183         status = "okay";
 184 };
 185
 186 &usb0 {
 187         #address-cells = <1>;
 188         #size-cells = <0>;
 189         status = "okay";
 190
 191         hub_port0: port@1 {
 192                 reg = <1>;
 193                 #trigger-source-cells = <0>;
 194         };
 195 };