target/linux/ath79/dts/ar9331_tplink_tl-wr703n_tl-mr10u.dtsi

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2
   3 #include <dt-bindings/gpio/gpio.h>
   4 #include <dt-bindings/input/input.h>
   5
   6 #include "ar9331.dtsi"
   7
   8 / {
   9         aliases {
  10                 serial0 = &uart;
  11                 led-boot = &led_system;
  12                 led-failsafe = &led_system;
  13                 led-running = &led_system;
  14                 led-upgrade = &led_system;
  15                 label-mac-device = &eth0;
  16         };
  17
  18         keys {
  19                 compatible = "gpio-keys";
  20
  21                 reset {
  22                         label = "reset";
  23                         linux,code = <KEY_RESTART>;
  24                         gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
  25                         debounce-interval = <60>;
  26                 };
  27         };
  28
  29         leds {
  30                 compatible = "gpio-leds";
  31
  32                 led_system: system {
  33                         label = "tl-wr703n:blue:system";
  34                         gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
  35                 };
  36         };
  37
  38         reg_usb_vbus: reg_usb_vbus {
  39                 compatible = "regulator-fixed";
  40                 regulator-name = "usb_vbus";
  41                 regulator-min-microvolt = <5000000>;
  42                 regulator-max-microvolt = <5000000>;
  43                 enable-active-high;
  44         };
  45 };
  46
  47 &spi {
  48         status = "okay";
  49
  50         num-cs = <1>;
  51
  52         flash@0 {
  53                 compatible = "jedec,spi-nor";
  54                 reg = <0>;
  55                 spi-max-frequency = <25000000>;
  56
  57                 partitions {
  58                         compatible = "fixed-partitions";
  59                         #address-cells = <1>;
  60                         #size-cells = <1>;
  61
  62                         uboot: partition@0 {
  63                                 reg = <0x0 0x20000>;
  64                                 label = "u-boot";
  65                                 read-only;
  66                         };
  67
  68                         partition@20000 {
  69                                 compatible = "tplink,firmware";
  70                                 reg = <0x20000 0x3d0000>;
  71                                 label = "firmware";
  72                         };
  73
  74                         art: partition@3f0000 {
  75                                 reg = <0x3f0000 0x10000>;
  76                                 label = "art";
  77                                 read-only;
  78                         };
  79                 };
  80         };
  81 };
  82
  83 &eth0 {
  84         status = "okay";
  85
  86         mtd-mac-address = <&uboot 0x1fc00>;
  87
  88         gmac-config {
  89                 device = <&gmac>;
  90
  91                 switch-phy-addr-swap = <0>;
  92                 switch-phy-swap = <0>;
  93         };
  94 };
  95
  96 &eth1 {
  97         status = "okay";
  98
  99         compatible = "syscon", "simple-mfd";
 100 };
 101
 102 &gpio {
 103         status = "okay";
 104 };
 105
 106 &uart {
 107         status = "okay";
 108 };
 109
 110 &usb {
 111         dr_mode = "host";
 112         vbus-supply = <&reg_usb_vbus>;
 113         status = "okay";
 114 };
 115
 116 &usb_phy {
 117         status = "okay";
 118 };
 119
 120 &wmac {
 121         status = "okay";
 122
 123         mtd-cal-data = <&art 0x1000>;
 124         mtd-mac-address = <&uboot 0x1fc00>;
 125 };