drivers/net/irda/irda-usb.c

   1 /*****************************************************************************
   2  *
   3  * Filename:      irda-usb.c
   4  * Version:       0.10
   5  * Description:   IrDA-USB Driver
   6  * Status:        Experimental
   7  * Author:        Dag Brattli <dag@brattli.net>
   8  *
   9  *      Copyright (C) 2000, Roman Weissgaerber <weissg@vienna.at>
  10  *      Copyright (C) 2001, Dag Brattli <dag@brattli.net>
  11  *      Copyright (C) 2001, Jean Tourrilhes <jt@hpl.hp.com>
  12  *      Copyright (C) 2004, SigmaTel, Inc. <irquality@sigmatel.com>
  13  *      Copyright (C) 2005, Milan Beno <beno@pobox.sk>
  14  *      Copyright (C) 2006, Nick Fedchik <nick@fedchik.org.ua>
  15  *
  16  *      This program is free software; you can redistribute it and/or modify
  17  *      it under the terms of the GNU General Public License as published by
  18  *      the Free Software Foundation; either version 2 of the License, or
  19  *      (at your option) any later version.
  20  *
  21  *      This program is distributed in the hope that it will be useful,
  22  *      but WITHOUT ANY WARRANTY; without even the implied warranty of
  23  *      MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  24  *      GNU General Public License for more details.
  25  *
  26  *      You should have received a copy of the GNU General Public License
  27  *      along with this program; if not, write to the Free Software
  28  *      Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  29  *
  30  *****************************************************************************/
  31
  32 /*
  33  *                          IMPORTANT NOTE
  34  *                          --------------
  35  *
  36  * As of kernel 2.5.20, this is the state of compliance and testing of
  37  * this driver (irda-usb) with regards to the USB low level drivers...
  38  *
  39  * This driver has been tested SUCCESSFULLY with the following drivers :
  40  *      o usb-uhci-hcd  (For Intel/Via USB controllers)
  41  *      o uhci-hcd      (Alternate/JE driver for Intel/Via USB controllers)
  42  *      o ohci-hcd      (For other USB controllers)
  43  *
  44  * This driver has NOT been tested with the following drivers :
  45  *      o ehci-hcd      (USB 2.0 controllers)
  46  *
  47  * Note that all HCD drivers do URB_ZERO_PACKET and timeout properly,
  48  * so we don't have to worry about that anymore.
  49  * One common problem is the failure to set the address on the dongle,
  50  * but this happens before the driver gets loaded...
  51  *
  52  * Jean II
  53  */
  54
  55 /*------------------------------------------------------------------*/
  56
  57 #include <linux/module.h>
  58 #include <linux/moduleparam.h>
  59 #include <linux/kernel.h>
  60 #include <linux/types.h>
  61 #include <linux/skbuff.h>
  62 #include <linux/netdevice.h>
  63 #include <linux/slab.h>
  64 #include <linux/rtnetlink.h>
  65 #include <linux/usb.h>
  66 #include <linux/firmware.h>
  67
  68 #include "irda-usb.h"
  69
  70 /*------------------------------------------------------------------*/
  71
  72 static int qos_mtt_bits = 0;
  73
  74 /* These are the currently known IrDA USB dongles. Add new dongles here */
  75 static struct usb_device_id dongles[] = {
  76         /* ACTiSYS Corp.,  ACT-IR2000U FIR-USB Adapter */
  77         { USB_DEVICE(0x9c4, 0x011), .driver_info = IUC_SPEED_BUG | IUC_NO_WINDOW },
  78         /* Look like ACTiSYS, Report : IBM Corp., IBM UltraPort IrDA */
  79         { USB_DEVICE(0x4428, 0x012), .driver_info = IUC_SPEED_BUG | IUC_NO_WINDOW },
  80         /* KC Technology Inc.,  KC-180 USB IrDA Device */
  81         { USB_DEVICE(0x50f, 0x180), .driver_info = IUC_SPEED_BUG | IUC_NO_WINDOW },
  82         /* Extended Systems, Inc.,  XTNDAccess IrDA USB (ESI-9685) */
  83         { USB_DEVICE(0x8e9, 0x100), .driver_info = IUC_SPEED_BUG | IUC_NO_WINDOW },
  84         /* SigmaTel STIR4210/4220/4116 USB IrDA (VFIR) Bridge */
  85         { USB_DEVICE(0x66f, 0x4210), .driver_info = IUC_STIR421X | IUC_SPEED_BUG },
  86         { USB_DEVICE(0x66f, 0x4220), .driver_info = IUC_STIR421X | IUC_SPEED_BUG },
  87         { USB_DEVICE(0x66f, 0x4116), .driver_info = IUC_STIR421X | IUC_SPEED_BUG },
  88         { .match_flags = USB_DEVICE_ID_MATCH_INT_CLASS |
  89           USB_DEVICE_ID_MATCH_INT_SUBCLASS,
  90           .bInterfaceClass = USB_CLASS_APP_SPEC,
  91           .bInterfaceSubClass = USB_CLASS_IRDA,
  92           .driver_info = IUC_DEFAULT, },
  93         { }, /* The end */
  94 };
  95
  96 /*
  97  * Important note :
  98  * Devices based on the SigmaTel chipset (0x66f, 0x4200) are not designed
  99  * using the "USB-IrDA specification" (yes, there exist such a thing), and
 100  * therefore not supported by this driver (don't add them above).
 101  * There is a Linux driver, stir4200, that support those USB devices.
 102  * Jean II
 103  */
 104
 105 MODULE_DEVICE_TABLE(usb, dongles);
 106
 107 /*------------------------------------------------------------------*/
 108
 109 static void irda_usb_init_qos(struct irda_usb_cb *self) ;
 110 static struct irda_class_desc *irda_usb_find_class_desc(struct usb_interface *intf);
 111 static void irda_usb_disconnect(struct usb_interface *intf);
 112 static void irda_usb_change_speed_xbofs(struct irda_usb_cb *self);
 113 static netdev_tx_t irda_usb_hard_xmit(struct sk_buff *skb,
 114                                             struct net_device *dev);
 115 static int irda_usb_open(struct irda_usb_cb *self);
 116 static void irda_usb_close(struct irda_usb_cb *self);
 117 static void speed_bulk_callback(struct urb *urb);
 118 static void write_bulk_callback(struct urb *urb);
 119 static void irda_usb_receive(struct urb *urb);
 120 static void irda_usb_rx_defer_expired(unsigned long data);
 121 static int irda_usb_net_open(struct net_device *dev);
 122 static int irda_usb_net_close(struct net_device *dev);
 123 static int irda_usb_net_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
 124 static void irda_usb_net_timeout(struct net_device *dev);
 125
 126 /************************ TRANSMIT ROUTINES ************************/
 127 /*
 128  * Receive packets from the IrDA stack and send them on the USB pipe.
 129  * Handle speed change, timeout and lot's of ugliness...
 130  */
 131
 132 /*------------------------------------------------------------------*/
 133 /*
 134  * Function irda_usb_build_header(self, skb, header)
 135  *
 136  *   Builds USB-IrDA outbound header
 137  *
 138  * When we send an IrDA frame over an USB pipe, we add to it a 1 byte
 139  * header. This function create this header with the proper values.
 140  *
 141  * Important note : the USB-IrDA spec 1.0 say very clearly in chapter 5.4.2.2
 142  * that the setting of the link speed and xbof number in this outbound header
 143  * should be applied *AFTER* the frame has been sent.
 144  * Unfortunately, some devices are not compliant with that... It seems that
 145  * reading the spec is far too difficult...
 146  * Jean II
 147  */
 148 static void irda_usb_build_header(struct irda_usb_cb *self,
 149                                   __u8 *header,
 150                                   int   force)
 151 {
 152         /* Here we check if we have an STIR421x chip,
 153          * and if either speed or xbofs (or both) needs
 154          * to be changed.
 155          */
 156         if (self->capability & IUC_STIR421X &&
 157             ((self->new_speed != -1) || (self->new_xbofs != -1))) {
 158
 159                 /* With STIR421x, speed and xBOFs must be set at the same
 160                  * time, even if only one of them changes.
 161                  */
 162                 if (self->new_speed == -1)
 163                         self->new_speed = self->speed ;
 164
 165                 if (self->new_xbofs == -1)
 166                         self->new_xbofs = self->xbofs ;
 167         }
 168
 169         /* Set the link speed */
 170         if (self->new_speed != -1) {
 171                 /* Hum... Ugly hack :-(
 172                  * Some device are not compliant with the spec and change
 173                  * parameters *before* sending the frame. - Jean II
 174                  */
 175                 if ((self->capability & IUC_SPEED_BUG) &&
 176                     (!force) && (self->speed != -1)) {
 177                         /* No speed and xbofs change here
 178                          * (we'll do it later in the write callback) */
 179                         IRDA_DEBUG(2, "%s(), not changing speed yet\n", __func__);
 180                         *header = 0;
 181                         return;
 182                 }
 183
 184                 IRDA_DEBUG(2, "%s(), changing speed to %d\n", __func__, self->new_speed);
 185                 self->speed = self->new_speed;
 186                 /* We will do ` self->new_speed = -1; ' in the completion
 187                  * handler just in case the current URB fail - Jean II */
 188
 189                 switch (self->speed) {
 190                 case 2400:
 191                         *header = SPEED_2400;
 192                         break;
 193                 default:
 194                 case 9600:
 195                         *header = SPEED_9600;
 196                         break;
 197                 case 19200:
 198                         *header = SPEED_19200;
 199                         break;
 200                 case 38400:
 201                         *header = SPEED_38400;
 202                         break;
 203                 case 57600:
 204                         *header = SPEED_57600;
 205                         break;
 206                 case 115200:
 207                         *header = SPEED_115200;
 208                         break;
 209                 case 576000:
 210                         *header = SPEED_576000;
 211                         break;
 212                 case 1152000:
 213                         *header = SPEED_1152000;
 214                         break;
 215                 case 4000000:
 216                         *header = SPEED_4000000;
 217                         self->new_xbofs = 0;
 218                         break;
 219                 case 16000000:
 220                         *header = SPEED_16000000;
 221                         self->new_xbofs = 0;
 222                         break;
 223                 }
 224         } else
 225                 /* No change */
 226                 *header = 0;
 227
 228         /* Set the negotiated additional XBOFS */
 229         if (self->new_xbofs != -1) {
 230                 IRDA_DEBUG(2, "%s(), changing xbofs to %d\n", __func__, self->new_xbofs);
 231                 self->xbofs = self->new_xbofs;
 232                 /* We will do ` self->new_xbofs = -1; ' in the completion
 233                  * handler just in case the current URB fail - Jean II */
 234
 235                 switch (self->xbofs) {
 236                 case 48:
 237                         *header |= 0x10;
 238                         break;
 239                 case 28:
 240                 case 24:        /* USB spec 1.0 says 24 */
 241                         *header |= 0x20;
 242                         break;
 243                 default:
 244                 case 12:
 245                         *header |= 0x30;
 246                         break;
 247                 case 5: /* Bug in IrLAP spec? (should be 6) */
 248                 case 6:
 249                         *header |= 0x40;
 250                         break;
 251                 case 3:
 252                         *header |= 0x50;
 253                         break;
 254                 case 2:
 255                         *header |= 0x60;
 256                         break;
 257                 case 1:
 258                         *header |= 0x70;
 259                         break;
 260                 case 0:
 261                         *header |= 0x80;
 262                         break;
 263                 }
 264         }
 265 }
 266
 267 /*
 268 *   calculate turnaround time for SigmaTel header
 269 */
 270 static __u8 get_turnaround_time(struct sk_buff *skb)
 271 {
 272         int turnaround_time = irda_get_mtt(skb);
 273
 274         if ( turnaround_time == 0 )
 275                 return 0;
 276         else if ( turnaround_time <= 10 )
 277                 return 1;
 278         else if ( turnaround_time <= 50 )
 279                 return 2;
 280         else if ( turnaround_time <= 100 )
 281                 return 3;
 282         else if ( turnaround_time <= 500 )
 283                 return 4;
 284         else if ( turnaround_time <= 1000 )
 285                 return 5;
 286         else if ( turnaround_time <= 5000 )
 287                 return 6;
 288         else
 289                 return 7;
 290 }
 291
 292
 293 /*------------------------------------------------------------------*/
 294 /*
 295  * Send a command to change the speed of the dongle
 296  * Need to be called with spinlock on.
 297  */
 298 static void irda_usb_change_speed_xbofs(struct irda_usb_cb *self)
 299 {
 300         __u8 *frame;
 301         struct urb *urb;
 302         int ret;
 303
 304         IRDA_DEBUG(2, "%s(), speed=%d, xbofs=%d\n", __func__,
 305                    self->new_speed, self->new_xbofs);
 306
 307         /* Grab the speed URB */
 308         urb = self->speed_urb;
 309         if (urb->status != 0) {
 310                 IRDA_WARNING("%s(), URB still in use!\n", __func__);
 311                 return;
 312         }
 313
 314         /* Allocate the fake frame */
 315         frame = self->speed_buff;
 316
 317         /* Set the new speed and xbofs in this fake frame */
 318         irda_usb_build_header(self, frame, 1);
 319
 320         if (self->capability & IUC_STIR421X) {
 321                 if (frame[0] == 0) return ; // do nothing if no change
 322                 frame[1] = 0; // other parameters don't change here
 323                 frame[2] = 0;
 324         }
 325
 326         /* Submit the 0 length IrDA frame to trigger new speed settings */
 327         usb_fill_bulk_urb(urb, self->usbdev,
 328                       usb_sndbulkpipe(self->usbdev, self->bulk_out_ep),
 329                       frame, IRDA_USB_SPEED_MTU,
 330                       speed_bulk_callback, self);
 331         urb->transfer_buffer_length = self->header_length;
 332         urb->transfer_flags = 0;
 333
 334         /* Irq disabled -> GFP_ATOMIC */
 335         if ((ret = usb_submit_urb(urb, GFP_ATOMIC))) {
 336                 IRDA_WARNING("%s(), failed Speed URB\n", __func__);
 337         }
 338 }
 339
 340 /*------------------------------------------------------------------*/
 341 /*
 342  * Speed URB callback
 343  * Now, we can only get called for the speed URB.
 344  */
 345 static void speed_bulk_callback(struct urb *urb)
 346 {
 347         struct irda_usb_cb *self = urb->context;
 348
 349         IRDA_DEBUG(2, "%s()\n", __func__);
 350
 351         /* We should always have a context */
 352         IRDA_ASSERT(self != NULL, return;);
 353         /* We should always be called for the speed URB */
 354         IRDA_ASSERT(urb == self->speed_urb, return;);
 355
 356         /* Check for timeout and other USB nasties */
 357         if (urb->status != 0) {
 358                 /* I get a lot of -ECONNABORTED = -103 here - Jean II */
 359                 IRDA_DEBUG(0, "%s(), URB complete status %d, transfer_flags 0x%04X\n", __func__, urb->status, urb->transfer_flags);
 360
 361                 /* Don't do anything here, that might confuse the USB layer.
 362                  * Instead, we will wait for irda_usb_net_timeout(), the
 363                  * network layer watchdog, to fix the situation.
 364                  * Jean II */
 365                 /* A reset of the dongle might be welcomed here - Jean II */
 366                 return;
 367         }
 368
 369         /* urb is now available */
 370         //urb->status = 0; -> tested above
 371
 372         /* New speed and xbof is now committed in hardware */
 373         self->new_speed = -1;
 374         self->new_xbofs = -1;
 375
 376         /* Allow the stack to send more packets */
 377         netif_wake_queue(self->netdev);
 378 }
 379
 380 /*------------------------------------------------------------------*/
 381 /*
 382  * Send an IrDA frame to the USB dongle (for transmission)
 383  */
 384 static netdev_tx_t irda_usb_hard_xmit(struct sk_buff *skb,
 385                                             struct net_device *netdev)
 386 {
 387         struct irda_usb_cb *self = netdev_priv(netdev);
 388         struct urb *urb = self->tx_urb;
 389         unsigned long flags;
 390         s32 speed;
 391         s16 xbofs;
 392         int res, mtt;
 393
 394         IRDA_DEBUG(4, "%s() on %s\n", __func__, netdev->name);
 395
 396         netif_stop_queue(netdev);
 397
 398         /* Protect us from USB callbacks, net watchdog and else. */
 399         spin_lock_irqsave(&self->lock, flags);
 400
 401         /* Check if the device is still there.
 402          * We need to check self->present under the spinlock because
 403          * of irda_usb_disconnect() is synchronous - Jean II */
 404         if (!self->present) {
 405                 IRDA_DEBUG(0, "%s(), Device is gone...\n", __func__);
 406                 goto drop;
 407         }
 408
 409         /* Check if we need to change the number of xbofs */
 410         xbofs = irda_get_next_xbofs(skb);
 411         if ((xbofs != self->xbofs) && (xbofs != -1)) {
 412                 self->new_xbofs = xbofs;
 413         }
 414
 415         /* Check if we need to change the speed */
 416         speed = irda_get_next_speed(skb);
 417         if ((speed != self->speed) && (speed != -1)) {
 418                 /* Set the desired speed */
 419                 self->new_speed = speed;
 420
 421                 /* Check for empty frame */
 422                 if (!skb->len) {
 423                         /* IrLAP send us an empty frame to make us change the
 424                          * speed. Changing speed with the USB adapter is in
 425                          * fact sending an empty frame to the adapter, so we
 426                          * could just let the present function do its job.
 427                          * However, we would wait for min turn time,
 428                          * do an extra memcpy and increment packet counters...
 429                          * Jean II */
 430                         irda_usb_change_speed_xbofs(self);
 431                         netdev->trans_start = jiffies;
 432                         /* Will netif_wake_queue() in callback */
 433                         goto drop;
 434                 }
 435         }
 436
 437         if (urb->status != 0) {
 438                 IRDA_WARNING("%s(), URB still in use!\n", __func__);
 439                 goto drop;
 440         }
 441
 442         skb_copy_from_linear_data(skb, self->tx_buff + self->header_length, skb->len);
 443
 444         /* Change setting for next frame */
 445         if (self->capability & IUC_STIR421X) {
 446                 __u8 turnaround_time;
 447                 __u8* frame = self->tx_buff;
 448                 turnaround_time = get_turnaround_time( skb );
 449                 irda_usb_build_header(self, frame, 0);
 450                 frame[2] = turnaround_time;
 451                 if ((skb->len != 0) &&
 452                     ((skb->len % 128) == 0) &&
 453                     ((skb->len % 512) != 0)) {
 454                         /* add extra byte for special SigmaTel feature */
 455                         frame[1] = 1;
 456                         skb_put(skb, 1);
 457                 } else {
 458                         frame[1] = 0;
 459                 }
 460         } else {
 461                 irda_usb_build_header(self, self->tx_buff, 0);
 462         }
 463
 464         /* FIXME: Make macro out of this one */
 465         ((struct irda_skb_cb *)skb->cb)->context = self;
 466
 467         usb_fill_bulk_urb(urb, self->usbdev,
 468                       usb_sndbulkpipe(self->usbdev, self->bulk_out_ep),
 469                       self->tx_buff, skb->len + self->header_length,
 470                       write_bulk_callback, skb);
 471
 472         /* This flag (URB_ZERO_PACKET) indicates that what we send is not
 473          * a continuous stream of data but separate packets.
 474          * In this case, the USB layer will insert an empty USB frame (TD)
 475          * after each of our packets that is exact multiple of the frame size.
 476          * This is how the dongle will detect the end of packet - Jean II */
 477         urb->transfer_flags = URB_ZERO_PACKET;
 478
 479         /* Generate min turn time. FIXME: can we do better than this? */
 480         /* Trying to a turnaround time at this level is trying to measure
 481          * processor clock cycle with a wrist-watch, approximate at best...
 482          *
 483          * What we know is the last time we received a frame over USB.
 484          * Due to latency over USB that depend on the USB load, we don't
 485          * know when this frame was received over IrDA (a few ms before ?)
 486          * Then, same story for our outgoing frame...
 487          *
 488          * In theory, the USB dongle is supposed to handle the turnaround
 489          * by itself (spec 1.0, chater 4, page 6). Who knows ??? That's
 490          * why this code is enabled only for dongles that doesn't meet
 491          * the spec.
 492          * Jean II */
 493         if (self->capability & IUC_NO_TURN) {
 494                 mtt = irda_get_mtt(skb);
 495                 if (mtt) {
 496                         int diff;
 497                         do_gettimeofday(&self->now);
 498                         diff = self->now.tv_usec - self->stamp.tv_usec;
 499 #ifdef IU_USB_MIN_RTT
 500                         /* Factor in USB delays -> Get rid of udelay() that
 501                          * would be lost in the noise - Jean II */
 502                         diff += IU_USB_MIN_RTT;
 503 #endif /* IU_USB_MIN_RTT */
 504                         /* If the usec counter did wraparound, the diff will
 505                          * go negative (tv_usec is a long), so we need to
 506                          * correct it by one second. Jean II */
 507                         if (diff < 0)
 508                                 diff += 1000000;
 509
 510                         /* Check if the mtt is larger than the time we have
 511                          * already used by all the protocol processing
 512                          */
 513                         if (mtt > diff) {
 514                                 mtt -= diff;
 515                                 if (mtt > 1000)
 516                                         mdelay(mtt/1000);
 517                                 else
 518                                         udelay(mtt);
 519                         }
 520                 }
 521         }
 522
 523         /* Ask USB to send the packet - Irq disabled -> GFP_ATOMIC */
 524         if ((res = usb_submit_urb(urb, GFP_ATOMIC))) {
 525                 IRDA_WARNING("%s(), failed Tx URB\n", __func__);
 526                 netdev->stats.tx_errors++;
 527                 /* Let USB recover : We will catch that in the watchdog */
 528                 /*netif_start_queue(netdev);*/
 529         } else {
 530                 /* Increment packet stats */
 531                 netdev->stats.tx_packets++;
 532                 netdev->stats.tx_bytes += skb->len;
 533
 534                 netdev->trans_start = jiffies;
 535         }
 536         spin_unlock_irqrestore(&self->lock, flags);
 537
 538         return NETDEV_TX_OK;
 539
 540 drop:
 541         /* Drop silently the skb and exit */
 542         dev_kfree_skb(skb);
 543         spin_unlock_irqrestore(&self->lock, flags);
 544         return NETDEV_TX_OK;
 545 }
 546
 547 /*------------------------------------------------------------------*/
 548 /*
 549  * Note : this function will be called only for tx_urb...
 550  */
 551 static void write_bulk_callback(struct urb *urb)
 552 {
 553         unsigned long flags;
 554         struct sk_buff *skb = urb->context;
 555         struct irda_usb_cb *self = ((struct irda_skb_cb *) skb->cb)->context;
 556
 557         IRDA_DEBUG(2, "%s()\n", __func__);
 558
 559         /* We should always have a context */
 560         IRDA_ASSERT(self != NULL, return;);
 561         /* We should always be called for the speed URB */
 562         IRDA_ASSERT(urb == self->tx_urb, return;);
 563
 564         /* Free up the skb */
 565         dev_kfree_skb_any(skb);
 566         urb->context = NULL;
 567
 568         /* Check for timeout and other USB nasties */
 569         if (urb->status != 0) {
 570                 /* I get a lot of -ECONNABORTED = -103 here - Jean II */
 571                 IRDA_DEBUG(0, "%s(), URB complete status %d, transfer_flags 0x%04X\n", __func__, urb->status, urb->transfer_flags);
 572
 573                 /* Don't do anything here, that might confuse the USB layer,
 574                  * and we could go in recursion and blow the kernel stack...
 575                  * Instead, we will wait for irda_usb_net_timeout(), the
 576                  * network layer watchdog, to fix the situation.
 577                  * Jean II */
 578                 /* A reset of the dongle might be welcomed here - Jean II */
 579                 return;
 580         }
 581
 582         /* urb is now available */
 583         //urb->status = 0; -> tested above
 584
 585         /* Make sure we read self->present properly */
 586         spin_lock_irqsave(&self->lock, flags);
 587
 588         /* If the network is closed, stop everything */
 589         if ((!self->netopen) || (!self->present)) {
 590                 IRDA_DEBUG(0, "%s(), Network is gone...\n", __func__);
 591                 spin_unlock_irqrestore(&self->lock, flags);
 592                 return;
 593         }
 594
 595         /* If changes to speed or xbofs is pending... */
 596         if ((self->new_speed != -1) || (self->new_xbofs != -1)) {
 597                 if ((self->new_speed != self->speed) ||
 598                     (self->new_xbofs != self->xbofs)) {
 599                         /* We haven't changed speed yet (because of
 600                          * IUC_SPEED_BUG), so do it now - Jean II */
 601                         IRDA_DEBUG(1, "%s(), Changing speed now...\n", __func__);
 602                         irda_usb_change_speed_xbofs(self);
 603                 } else {
 604                         /* New speed and xbof is now committed in hardware */
 605                         self->new_speed = -1;
 606                         self->new_xbofs = -1;
 607                         /* Done, waiting for next packet */
 608                         netif_wake_queue(self->netdev);
 609                 }
 610         } else {
 611                 /* Otherwise, allow the stack to send more packets */
 612                 netif_wake_queue(self->netdev);
 613         }
 614         spin_unlock_irqrestore(&self->lock, flags);
 615 }
 616
 617 /*------------------------------------------------------------------*/
 618 /*
 619  * Watchdog timer from the network layer.
 620  * After a predetermined timeout, if we don't give confirmation that
 621  * the packet has been sent (i.e. no call to netif_wake_queue()),
 622  * the network layer will call this function.
 623  * Note that URB that we submit have also a timeout. When the URB timeout
 624  * expire, the normal URB callback is called (write_bulk_callback()).
 625  */
 626 static void irda_usb_net_timeout(struct net_device *netdev)
 627 {
 628         unsigned long flags;
 629         struct irda_usb_cb *self = netdev_priv(netdev);
 630         struct urb *urb;
 631         int     done = 0;       /* If we have made any progress */
 632
 633         IRDA_DEBUG(0, "%s(), Network layer thinks we timed out!\n", __func__);
 634         IRDA_ASSERT(self != NULL, return;);
 635
 636         /* Protect us from USB callbacks, net Tx and else. */
 637         spin_lock_irqsave(&self->lock, flags);
 638
 639         /* self->present *MUST* be read under spinlock */
 640         if (!self->present) {
 641                 IRDA_WARNING("%s(), device not present!\n", __func__);
 642                 netif_stop_queue(netdev);
 643                 spin_unlock_irqrestore(&self->lock, flags);
 644                 return;
 645         }
 646
 647         /* Check speed URB */
 648         urb = self->speed_urb;
 649         if (urb->status != 0) {
 650                 IRDA_DEBUG(0, "%s: Speed change timed out, urb->status=%d, urb->transfer_flags=0x%04X\n", netdev->name, urb->status, urb->transfer_flags);
 651
 652                 switch (urb->status) {
 653                 case -EINPROGRESS:
 654                         usb_unlink_urb(urb);
 655                         /* Note : above will  *NOT* call netif_wake_queue()
 656                          * in completion handler, we will come back here.
 657                          * Jean II */
 658                         done = 1;
 659                         break;
 660                 case -ECONNRESET:
 661                 case -ENOENT:                   /* urb unlinked by us */
 662                 default:                        /* ??? - Play safe */
 663                         urb->status = 0;
 664                         netif_wake_queue(self->netdev);
 665                         done = 1;
 666                         break;
 667                 }
 668         }
 669
 670         /* Check Tx URB */
 671         urb = self->tx_urb;
 672         if (urb->status != 0) {
 673                 struct sk_buff *skb = urb->context;
 674
 675                 IRDA_DEBUG(0, "%s: Tx timed out, urb->status=%d, urb->transfer_flags=0x%04X\n", netdev->name, urb->status, urb->transfer_flags);
 676
 677                 /* Increase error count */
 678                 netdev->stats.tx_errors++;
 679
 680 #ifdef IU_BUG_KICK_TIMEOUT
 681                 /* Can't be a bad idea to reset the speed ;-) - Jean II */
 682                 if(self->new_speed == -1)
 683                         self->new_speed = self->speed;
 684                 if(self->new_xbofs == -1)
 685                         self->new_xbofs = self->xbofs;
 686                 irda_usb_change_speed_xbofs(self);
 687 #endif /* IU_BUG_KICK_TIMEOUT */
 688
 689                 switch (urb->status) {
 690                 case -EINPROGRESS:
 691                         usb_unlink_urb(urb);
 692                         /* Note : above will  *NOT* call netif_wake_queue()
 693                          * in completion handler, because urb->status will
 694                          * be -ENOENT. We will fix that at the next watchdog,
 695                          * leaving more time to USB to recover...
 696                          * Jean II */
 697                         done = 1;
 698                         break;
 699                 case -ECONNRESET:
 700                 case -ENOENT:                   /* urb unlinked by us */
 701                 default:                        /* ??? - Play safe */
 702                         if(skb != NULL) {
 703                                 dev_kfree_skb_any(skb);
 704                                 urb->context = NULL;
 705                         }
 706                         urb->status = 0;
 707                         netif_wake_queue(self->netdev);
 708                         done = 1;
 709                         break;
 710                 }
 711         }
 712         spin_unlock_irqrestore(&self->lock, flags);
 713
 714         /* Maybe we need a reset */
 715         /* Note : Some drivers seem to use a usb_set_interface() when they
 716          * need to reset the hardware. Hum...
 717          */
 718
 719         /* if(done == 0) */
 720 }
 721
 722 /************************* RECEIVE ROUTINES *************************/
 723 /*
 724  * Receive packets from the USB layer stack and pass them to the IrDA stack.
 725  * Try to work around USB failures...
 726  */
 727
 728 /*
 729  * Note :
 730  * Some of you may have noticed that most dongle have an interrupt in pipe
 731  * that we don't use. Here is the little secret...
 732  * When we hang a Rx URB on the bulk in pipe, it generates some USB traffic
 733  * in every USB frame. This is unnecessary overhead.
 734  * The interrupt in pipe will generate an event every time a packet is
 735  * received. Reading an interrupt pipe adds minimal overhead, but has some
 736  * latency (~1ms).
 737  * If we are connected (speed != 9600), we want to minimise latency, so
 738  * we just always hang the Rx URB and ignore the interrupt.
 739  * If we are not connected (speed == 9600), there is usually no Rx traffic,
 740  * and we want to minimise the USB overhead. In this case we should wait
 741  * on the interrupt pipe and hang the Rx URB only when an interrupt is
 742  * received.
 743  * Jean II
 744  *
 745  * Note : don't read the above as what we are currently doing, but as
 746  * something we could do with KC dongle. Also don't forget that the
 747  * interrupt pipe is not part of the original standard, so this would
 748  * need to be optional...
 749  * Jean II
 750  */
 751
 752 /*------------------------------------------------------------------*/
 753 /*
 754  * Submit a Rx URB to the USB layer to handle reception of a frame
 755  * Mostly called by the completion callback of the previous URB.
 756  *
 757  * Jean II
 758  */
 759 static void irda_usb_submit(struct irda_usb_cb *self, struct sk_buff *skb, struct urb *urb)
 760 {
 761         struct irda_skb_cb *cb;
 762         int ret;
 763
 764         IRDA_DEBUG(2, "%s()\n", __func__);
 765
 766         /* This should never happen */
 767         IRDA_ASSERT(skb != NULL, return;);
 768         IRDA_ASSERT(urb != NULL, return;);
 769
 770         /* Save ourselves in the skb */
 771         cb = (struct irda_skb_cb *) skb->cb;
 772         cb->context = self;
 773
 774         /* Reinitialize URB */
 775         usb_fill_bulk_urb(urb, self->usbdev,
 776                       usb_rcvbulkpipe(self->usbdev, self->bulk_in_ep),
 777                       skb->data, IRDA_SKB_MAX_MTU,
 778                       irda_usb_receive, skb);
 779         urb->status = 0;
 780
 781         /* Can be called from irda_usb_receive (irq handler) -> GFP_ATOMIC */
 782         ret = usb_submit_urb(urb, GFP_ATOMIC);
 783         if (ret) {
 784                 /* If this ever happen, we are in deep s***.
 785                  * Basically, the Rx path will stop... */
 786                 IRDA_WARNING("%s(), Failed to submit Rx URB %d\n",
 787                              __func__, ret);
 788         }
 789 }
 790
 791 /*------------------------------------------------------------------*/
 792 /*
 793  * Function irda_usb_receive(urb)
 794  *
 795  *     Called by the USB subsystem when a frame has been received
 796  *
 797  */
 798 static void irda_usb_receive(struct urb *urb)
 799 {
 800         struct sk_buff *skb = (struct sk_buff *) urb->context;
 801         struct irda_usb_cb *self;
 802         struct irda_skb_cb *cb;
 803         struct sk_buff *newskb;
 804         struct sk_buff *dataskb;
 805         struct urb *next_urb;
 806         unsigned int len, docopy;
 807
 808         IRDA_DEBUG(2, "%s(), len=%d\n", __func__, urb->actual_length);
 809
 810         /* Find ourselves */
 811         cb = (struct irda_skb_cb *) skb->cb;
 812         IRDA_ASSERT(cb != NULL, return;);
 813         self = (struct irda_usb_cb *) cb->context;
 814         IRDA_ASSERT(self != NULL, return;);
 815
 816         /* If the network is closed or the device gone, stop everything */
 817         if ((!self->netopen) || (!self->present)) {
 818                 IRDA_DEBUG(0, "%s(), Network is gone!\n", __func__);
 819                 /* Don't re-submit the URB : will stall the Rx path */
 820                 return;
 821         }
 822
 823         /* Check the status */
 824         if (urb->status != 0) {
 825                 switch (urb->status) {
 826                 case -EILSEQ:
 827                         self->netdev->stats.rx_crc_errors++;
 828                         /* Also precursor to a hot-unplug on UHCI. */
 829                         /* Fallthrough... */
 830                 case -ECONNRESET:
 831                         /* Random error, if I remember correctly */
 832                         /* uhci_cleanup_unlink() is going to kill the Rx
 833                          * URB just after we return. No problem, at this
 834                          * point the URB will be idle ;-) - Jean II */
 835                 case -ESHUTDOWN:
 836                         /* That's usually a hot-unplug. Submit will fail... */
 837                 case -ETIME:
 838                         /* Usually precursor to a hot-unplug on OHCI. */
 839                 default:
 840                         self->netdev->stats.rx_errors++;
 841                         IRDA_DEBUG(0, "%s(), RX status %d, transfer_flags 0x%04X\n", __func__, urb->status, urb->transfer_flags);
 842                         break;
 843                 }
 844                 /* If we received an error, we don't want to resubmit the
 845                  * Rx URB straight away but to give the USB layer a little
 846                  * bit of breathing room.
 847                  * We are in the USB thread context, therefore there is a
 848                  * danger of recursion (new URB we submit fails, we come
 849                  * back here).
 850                  * With recent USB stack (2.6.15+), I'm seeing that on
 851                  * hot unplug of the dongle...
 852                  * Lowest effective timer is 10ms...
 853                  * Jean II */
 854                 self->rx_defer_timer.function = irda_usb_rx_defer_expired;
 855                 self->rx_defer_timer.data = (unsigned long) urb;
 856                 mod_timer(&self->rx_defer_timer, jiffies + (10 * HZ / 1000));
 857                 return;
 858         }
 859
 860         /* Check for empty frames */
 861         if (urb->actual_length <= self->header_length) {
 862                 IRDA_WARNING("%s(), empty frame!\n", __func__);
 863                 goto done;
 864         }
 865
 866         /*
 867          * Remember the time we received this frame, so we can
 868          * reduce the min turn time a bit since we will know
 869          * how much time we have used for protocol processing
 870          */
 871         do_gettimeofday(&self->stamp);
 872
 873         /* Check if we need to copy the data to a new skb or not.
 874          * For most frames, we use ZeroCopy and pass the already
 875          * allocated skb up the stack.
 876          * If the frame is small, it is more efficient to copy it
 877          * to save memory (copy will be fast anyway - that's
 878          * called Rx-copy-break). Jean II */
 879         docopy = (urb->actual_length < IRDA_RX_COPY_THRESHOLD);
 880
 881         /* Allocate a new skb */
 882         if (self->capability & IUC_STIR421X)
 883                 newskb = dev_alloc_skb(docopy ? urb->actual_length :
 884                                        IRDA_SKB_MAX_MTU +
 885                                        USB_IRDA_STIR421X_HEADER);
 886         else
 887                 newskb = dev_alloc_skb(docopy ? urb->actual_length :
 888                                        IRDA_SKB_MAX_MTU);
 889
 890         if (!newskb)  {
 891                 self->netdev->stats.rx_dropped++;
 892                 /* We could deliver the current skb, but this would stall
 893                  * the Rx path. Better drop the packet... Jean II */
 894                 goto done;
 895         }
 896
 897         /* Make sure IP header get aligned (IrDA header is 5 bytes) */
 898         /* But IrDA-USB header is 1 byte. Jean II */
 899         //skb_reserve(newskb, USB_IRDA_HEADER - 1);
 900
 901         if(docopy) {
 902                 /* Copy packet, so we can recycle the original */
 903                 skb_copy_from_linear_data(skb, newskb->data, urb->actual_length);
 904                 /* Deliver this new skb */
 905                 dataskb = newskb;
 906                 /* And hook the old skb to the URB
 907                  * Note : we don't need to "clean up" the old skb,
 908                  * as we never touched it. Jean II */
 909         } else {
 910                 /* We are using ZeroCopy. Deliver old skb */
 911                 dataskb = skb;
 912                 /* And hook the new skb to the URB */
 913                 skb = newskb;
 914         }
 915
 916         /* Set proper length on skb & remove USB-IrDA header */
 917         skb_put(dataskb, urb->actual_length);
 918         skb_pull(dataskb, self->header_length);
 919
 920         /* Ask the networking layer to queue the packet for the IrDA stack */
 921         dataskb->dev = self->netdev;
 922         skb_reset_mac_header(dataskb);
 923         dataskb->protocol = htons(ETH_P_IRDA);
 924         len = dataskb->len;
 925         netif_rx(dataskb);
 926
 927         /* Keep stats up to date */
 928         self->netdev->stats.rx_bytes += len;
 929         self->netdev->stats.rx_packets++;
 930
 931 done:
 932         /* Note : at this point, the URB we've just received (urb)
 933          * is still referenced by the USB layer. For example, if we
 934          * have received a -ECONNRESET, uhci_cleanup_unlink() will
 935          * continue to process it (in fact, cleaning it up).
 936          * If we were to submit this URB, disaster would ensue.
 937          * Therefore, we submit our idle URB, and put this URB in our
 938          * idle slot....
 939          * Jean II */
 940         /* Note : with this scheme, we could submit the idle URB before
 941          * processing the Rx URB. I don't think it would buy us anything as
 942          * we are running in the USB thread context. Jean II */
 943         next_urb = self->idle_rx_urb;
 944
 945         /* Recycle Rx URB : Now, the idle URB is the present one */
 946         urb->context = NULL;
 947         self->idle_rx_urb = urb;
 948
 949         /* Submit the idle URB to replace the URB we've just received.
 950          * Do it last to avoid race conditions... Jean II */
 951         irda_usb_submit(self, skb, next_urb);
 952 }
 953
 954 /*------------------------------------------------------------------*/
 955 /*
 956  * In case of errors, we want the USB layer to have time to recover.
 957  * Now, it is time to resubmit ouur Rx URB...
 958  */
 959 static void irda_usb_rx_defer_expired(unsigned long data)
 960 {
 961         struct urb *urb = (struct urb *) data;
 962         struct sk_buff *skb = (struct sk_buff *) urb->context;
 963         struct irda_usb_cb *self;
 964         struct irda_skb_cb *cb;
 965         struct urb *next_urb;
 966
 967         IRDA_DEBUG(2, "%s()\n", __func__);
 968
 969         /* Find ourselves */
 970         cb = (struct irda_skb_cb *) skb->cb;
 971         IRDA_ASSERT(cb != NULL, return;);
 972         self = (struct irda_usb_cb *) cb->context;
 973         IRDA_ASSERT(self != NULL, return;);
 974
 975         /* Same stuff as when Rx is done, see above... */
 976         next_urb = self->idle_rx_urb;
 977         urb->context = NULL;
 978         self->idle_rx_urb = urb;
 979         irda_usb_submit(self, skb, next_urb);
 980 }
 981
 982 /*------------------------------------------------------------------*/
 983 /*
 984  * Callbak from IrDA layer. IrDA wants to know if we have
 985  * started receiving anything.
 986  */
 987 static int irda_usb_is_receiving(struct irda_usb_cb *self)
 988 {
 989         /* Note : because of the way UHCI works, it's almost impossible
 990          * to get this info. The Controller DMA directly to memory and
 991          * signal only when the whole frame is finished. To know if the
 992          * first TD of the URB has been filled or not seems hard work...
 993          *
 994          * The other solution would be to use the "receiving" command
 995          * on the default decriptor with a usb_control_msg(), but that
 996          * would add USB traffic and would return result only in the
 997          * next USB frame (~1ms).
 998          *
 999          * I've been told that current dongles send status info on their
1000          * interrupt endpoint, and that's what the Windows driver uses
1001          * to know this info. Unfortunately, this is not yet in the spec...
1002          *
1003          * Jean II
1004          */
1005
1006         return 0; /* For now */
1007 }
1008
1009 #define STIR421X_PATCH_PRODUCT_VER     "Product Version: "
1010 #define STIR421X_PATCH_STMP_TAG        "STMP"
1011 #define STIR421X_PATCH_CODE_OFFSET     512 /* patch image starts before here */
1012 /* marks end of patch file header (PC DOS text file EOF character) */
1013 #define STIR421X_PATCH_END_OF_HDR_TAG  0x1A
1014 #define STIR421X_PATCH_BLOCK_SIZE      1023
1015
1016 /*
1017  * Function stir421x_fwupload (struct irda_usb_cb *self,
1018  *                             unsigned char *patch,
1019  *                             const unsigned int patch_len)
1020  *
1021  *   Upload firmware code to SigmaTel 421X IRDA-USB dongle
1022  */
1023 static int stir421x_fw_upload(struct irda_usb_cb *self,
1024                              const unsigned char *patch,
1025                              const unsigned int patch_len)
1026 {
1027         int ret = -ENOMEM;
1028         int actual_len = 0;
1029         unsigned int i;
1030         unsigned int block_size = 0;
1031         unsigned char *patch_block;
1032
1033         patch_block = kzalloc(STIR421X_PATCH_BLOCK_SIZE, GFP_KERNEL);
1034         if (patch_block == NULL)
1035                 return -ENOMEM;
1036
1037         /* break up patch into 1023-byte sections */
1038         for (i = 0; i < patch_len; i += block_size) {
1039                 block_size = patch_len - i;
1040
1041                 if (block_size > STIR421X_PATCH_BLOCK_SIZE)
1042                         block_size = STIR421X_PATCH_BLOCK_SIZE;
1043
1044                 /* upload the patch section */
1045                 memcpy(patch_block, patch + i, block_size);
1046
1047                 ret = usb_bulk_msg(self->usbdev,
1048                                    usb_sndbulkpipe(self->usbdev,
1049                                                    self->bulk_out_ep),
1050                                    patch_block, block_size,
1051                                    &actual_len, msecs_to_jiffies(500));
1052                 IRDA_DEBUG(3,"%s(): Bulk send %u bytes, ret=%d\n",
1053                            __func__, actual_len, ret);
1054
1055                 if (ret < 0)
1056                         break;
1057
1058                 mdelay(10);
1059         }
1060
1061         kfree(patch_block);
1062
1063         return ret;
1064  }
1065
1066 /*
1067  * Function stir421x_patch_device(struct irda_usb_cb *self)
1068  *
1069  * Get a firmware code from userspase using hotplug reject_firmware() call
1070   */
1071 static int stir421x_patch_device(struct irda_usb_cb *self)
1072 {
1073         unsigned int i;
1074         int ret;
1075         char stir421x_fw_name[12];
1076         const struct firmware *fw;
1077         const unsigned char *fw_version_ptr; /* pointer to version string */
1078         unsigned long fw_version = 0;
1079
1080         /*(DEBLOBBED)*/
1081         sprintf(stir421x_fw_name, "/*(DEBLOBBED)*/",
1082                 self->usbdev->descriptor.bcdDevice);
1083         ret = reject_firmware(&fw, stir421x_fw_name, &self->usbdev->dev);
1084         if (ret < 0)
1085                 return ret;
1086
1087         /* We get a patch from userspace */
1088         IRDA_MESSAGE("%s(): Received firmware %s (%zu bytes)\n",
1089                      __func__, stir421x_fw_name, fw->size);
1090
1091         ret = -EINVAL;
1092
1093         /* Get the bcd product version */
1094         if (!memcmp(fw->data, STIR421X_PATCH_PRODUCT_VER,
1095                     sizeof(STIR421X_PATCH_PRODUCT_VER) - 1)) {
1096                 fw_version_ptr = fw->data +
1097                         sizeof(STIR421X_PATCH_PRODUCT_VER) - 1;
1098
1099                 /* Let's check if the product version is dotted */
1100                 if (fw_version_ptr[3] == '.' &&
1101                     fw_version_ptr[7] == '.') {
1102                         unsigned long major, minor, build;
1103                         major = simple_strtoul(fw_version_ptr, NULL, 10);
1104                         minor = simple_strtoul(fw_version_ptr + 4, NULL, 10);
1105                         build = simple_strtoul(fw_version_ptr + 8, NULL, 10);
1106
1107                         fw_version = (major << 12)
1108                                 + (minor << 8)
1109                                 + ((build / 10) << 4)
1110                                 + (build % 10);
1111
1112                         IRDA_DEBUG(3, "%s(): Firmware Product version %ld\n",
1113                                    __func__, fw_version);
1114                 }
1115         }
1116
1117         if (self->usbdev->descriptor.bcdDevice == cpu_to_le16(fw_version)) {
1118                 /*
1119                  * If we're here, we've found a correct patch
1120                  * The actual image starts after the "STMP" keyword
1121                  * so forward to the firmware header tag
1122                  */
1123                 for (i = 0; i < fw->size && fw->data[i] !=
1124                              STIR421X_PATCH_END_OF_HDR_TAG; i++) ;
1125                 /* here we check for the out of buffer case */
1126                 if (i < STIR421X_PATCH_CODE_OFFSET && i < fw->size &&
1127                                 STIR421X_PATCH_END_OF_HDR_TAG == fw->data[i]) {
1128                         if (!memcmp(fw->data + i + 1, STIR421X_PATCH_STMP_TAG,
1129                                     sizeof(STIR421X_PATCH_STMP_TAG) - 1)) {
1130
1131                                 /* We can upload the patch to the target */
1132                                 i += sizeof(STIR421X_PATCH_STMP_TAG);
1133                                 ret = stir421x_fw_upload(self, &fw->data[i],
1134                                                          fw->size - i);
1135                         }
1136                 }
1137         }
1138
1139         release_firmware(fw);
1140
1141         return ret;
1142 }
1143
1144
1145 /********************** IRDA DEVICE CALLBACKS **********************/
1146 /*
1147  * Main calls from the IrDA/Network subsystem.
1148  * Mostly registering a new irda-usb device and removing it....
1149  * We only deal with the IrDA side of the business, the USB side will
1150  * be dealt with below...
1151  */
1152
1153
1154 /*------------------------------------------------------------------*/
1155 /*
1156  * Function irda_usb_net_open (dev)
1157  *
1158  *    Network device is taken up. Usually this is done by "ifconfig irda0 up"
1159  *
1160  * Note : don't mess with self->netopen - Jean II
1161  */
1162 static int irda_usb_net_open(struct net_device *netdev)
1163 {
1164         struct irda_usb_cb *self;
1165         unsigned long flags;
1166         char    hwname[16];
1167         int i;
1168
1169         IRDA_DEBUG(1, "%s()\n", __func__);
1170
1171         IRDA_ASSERT(netdev != NULL, return -1;);
1172         self = netdev_priv(netdev);
1173         IRDA_ASSERT(self != NULL, return -1;);
1174
1175         spin_lock_irqsave(&self->lock, flags);
1176         /* Can only open the device if it's there */
1177         if(!self->present) {
1178                 spin_unlock_irqrestore(&self->lock, flags);
1179                 IRDA_WARNING("%s(), device not present!\n", __func__);
1180                 return -1;
1181         }
1182
1183         if(self->needspatch) {
1184                 spin_unlock_irqrestore(&self->lock, flags);
1185                 IRDA_WARNING("%s(), device needs patch\n", __func__) ;
1186                 return -EIO ;
1187         }
1188
1189         /* Initialise default speed and xbofs value
1190          * (IrLAP will change that soon) */
1191         self->speed = -1;
1192         self->xbofs = -1;
1193         self->new_speed = -1;
1194         self->new_xbofs = -1;
1195
1196         /* To do *before* submitting Rx urbs and starting net Tx queue
1197          * Jean II */
1198         self->netopen = 1;
1199         spin_unlock_irqrestore(&self->lock, flags);
1200
1201         /*
1202          * Now that everything should be initialized properly,
1203          * Open new IrLAP layer instance to take care of us...
1204          * Note : will send immediately a speed change...
1205          */
1206         sprintf(hwname, "usb#%d", self->usbdev->devnum);
1207         self->irlap = irlap_open(netdev, &self->qos, hwname);
1208         IRDA_ASSERT(self->irlap != NULL, return -1;);
1209
1210         /* Allow IrLAP to send data to us */
1211         netif_start_queue(netdev);
1212
1213         /* We submit all the Rx URB except for one that we keep idle.
1214          * Need to be initialised before submitting other USBs, because
1215          * in some cases as soon as we submit the URBs the USB layer
1216          * will trigger a dummy receive - Jean II */
1217         self->idle_rx_urb = self->rx_urb[IU_MAX_ACTIVE_RX_URBS];
1218         self->idle_rx_urb->context = NULL;
1219
1220         /* Now that we can pass data to IrLAP, allow the USB layer
1221          * to send us some data... */
1222         for (i = 0; i < IU_MAX_ACTIVE_RX_URBS; i++) {
1223                 struct sk_buff *skb = dev_alloc_skb(IRDA_SKB_MAX_MTU);
1224                 if (!skb) {
1225                         /* If this ever happen, we are in deep s***.
1226                          * Basically, we can't start the Rx path... */
1227                         IRDA_WARNING("%s(), Failed to allocate Rx skb\n",
1228                                      __func__);
1229                         return -1;
1230                 }
1231                 //skb_reserve(newskb, USB_IRDA_HEADER - 1);
1232                 irda_usb_submit(self, skb, self->rx_urb[i]);
1233         }
1234
1235         /* Ready to play !!! */
1236         return 0;
1237 }
1238
1239 /*------------------------------------------------------------------*/
1240 /*
1241  * Function irda_usb_net_close (self)
1242  *
1243  *    Network device is taken down. Usually this is done by
1244  *    "ifconfig irda0 down"
1245  */
1246 static int irda_usb_net_close(struct net_device *netdev)
1247 {
1248         struct irda_usb_cb *self;
1249         int     i;
1250
1251         IRDA_DEBUG(1, "%s()\n", __func__);
1252
1253         IRDA_ASSERT(netdev != NULL, return -1;);
1254         self = netdev_priv(netdev);
1255         IRDA_ASSERT(self != NULL, return -1;);
1256
1257         /* Clear this flag *before* unlinking the urbs and *before*
1258          * stopping the network Tx queue - Jean II */
1259         self->netopen = 0;
1260
1261         /* Stop network Tx queue */
1262         netif_stop_queue(netdev);
1263
1264         /* Kill defered Rx URB */
1265         del_timer(&self->rx_defer_timer);
1266
1267         /* Deallocate all the Rx path buffers (URBs and skb) */
1268         for (i = 0; i < self->max_rx_urb; i++) {
1269                 struct urb *urb = self->rx_urb[i];
1270                 struct sk_buff *skb = (struct sk_buff *) urb->context;
1271                 /* Cancel the receive command */
1272                 usb_kill_urb(urb);
1273                 /* The skb is ours, free it */
1274                 if(skb) {
1275                         dev_kfree_skb(skb);
1276                         urb->context = NULL;
1277                 }
1278         }
1279         /* Cancel Tx and speed URB - need to be synchronous to avoid races */
1280         usb_kill_urb(self->tx_urb);
1281         usb_kill_urb(self->speed_urb);
1282
1283         /* Stop and remove instance of IrLAP */
1284         if (self->irlap)
1285                 irlap_close(self->irlap);
1286         self->irlap = NULL;
1287
1288         return 0;
1289 }
1290
1291 /*------------------------------------------------------------------*/
1292 /*
1293  * IOCTLs : Extra out-of-band network commands...
1294  */
1295 static int irda_usb_net_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
1296 {
1297         unsigned long flags;
1298         struct if_irda_req *irq = (struct if_irda_req *) rq;
1299         struct irda_usb_cb *self;
1300         int ret = 0;
1301
1302         IRDA_ASSERT(dev != NULL, return -1;);
1303         self = netdev_priv(dev);
1304         IRDA_ASSERT(self != NULL, return -1;);
1305
1306         IRDA_DEBUG(2, "%s(), %s, (cmd=0x%X)\n", __func__, dev->name, cmd);
1307
1308         switch (cmd) {
1309         case SIOCSBANDWIDTH: /* Set bandwidth */
1310                 if (!capable(CAP_NET_ADMIN))
1311                         return -EPERM;
1312                 /* Protect us from USB callbacks, net watchdog and else. */
1313                 spin_lock_irqsave(&self->lock, flags);
1314                 /* Check if the device is still there */
1315                 if(self->present) {
1316                         /* Set the desired speed */
1317                         self->new_speed = irq->ifr_baudrate;
1318                         irda_usb_change_speed_xbofs(self);
1319                 }
1320                 spin_unlock_irqrestore(&self->lock, flags);
1321                 break;
1322         case SIOCSMEDIABUSY: /* Set media busy */
1323                 if (!capable(CAP_NET_ADMIN))
1324                         return -EPERM;
1325                 /* Check if the IrDA stack is still there */
1326                 if(self->netopen)
1327                         irda_device_set_media_busy(self->netdev, TRUE);
1328                 break;
1329         case SIOCGRECEIVING: /* Check if we are receiving right now */
1330                 irq->ifr_receiving = irda_usb_is_receiving(self);
1331                 break;
1332         default:
1333                 ret = -EOPNOTSUPP;
1334         }
1335
1336         return ret;
1337 }
1338
1339 /*------------------------------------------------------------------*/
1340
1341 /********************* IRDA CONFIG SUBROUTINES *********************/
1342 /*
1343  * Various subroutines dealing with IrDA and network stuff we use to
1344  * configure and initialise each irda-usb instance.
1345  * These functions are used below in the main calls of the driver...
1346  */
1347
1348 /*------------------------------------------------------------------*/
1349 /*
1350  * Set proper values in the IrDA QOS structure
1351  */
1352 static inline void irda_usb_init_qos(struct irda_usb_cb *self)
1353 {
1354         struct irda_class_desc *desc;
1355
1356         IRDA_DEBUG(3, "%s()\n", __func__);
1357
1358         desc = self->irda_desc;
1359
1360         /* Initialize QoS for this device */
1361         irda_init_max_qos_capabilies(&self->qos);
1362
1363         /* See spec section 7.2 for meaning.
1364          * Values are little endian (as most USB stuff), the IrDA stack
1365          * use it in native order (see parameters.c). - Jean II */
1366         self->qos.baud_rate.bits       = le16_to_cpu(desc->wBaudRate);
1367         self->qos.min_turn_time.bits   = desc->bmMinTurnaroundTime;
1368         self->qos.additional_bofs.bits = desc->bmAdditionalBOFs;
1369         self->qos.window_size.bits     = desc->bmWindowSize;
1370         self->qos.data_size.bits       = desc->bmDataSize;
1371
1372         IRDA_DEBUG(0, "%s(), dongle says speed=0x%X, size=0x%X, window=0x%X, bofs=0x%X, turn=0x%X\n",
1373                 __func__, self->qos.baud_rate.bits, self->qos.data_size.bits, self->qos.window_size.bits, self->qos.additional_bofs.bits, self->qos.min_turn_time.bits);
1374
1375         /* Don't always trust what the dongle tell us */
1376         if(self->capability & IUC_SIR_ONLY)
1377                 self->qos.baud_rate.bits        &= 0x00ff;
1378         if(self->capability & IUC_SMALL_PKT)
1379                 self->qos.data_size.bits         = 0x07;
1380         if(self->capability & IUC_NO_WINDOW)
1381                 self->qos.window_size.bits       = 0x01;
1382         if(self->capability & IUC_MAX_WINDOW)
1383                 self->qos.window_size.bits       = 0x7f;
1384         if(self->capability & IUC_MAX_XBOFS)
1385                 self->qos.additional_bofs.bits   = 0x01;
1386
1387 #if 1
1388         /* Module parameter can override the rx window size */
1389         if (qos_mtt_bits)
1390                 self->qos.min_turn_time.bits = qos_mtt_bits;
1391 #endif
1392         /*
1393          * Note : most of those values apply only for the receive path,
1394          * the transmit path will be set differently - Jean II
1395          */
1396         irda_qos_bits_to_value(&self->qos);
1397 }
1398
1399 /*------------------------------------------------------------------*/
1400 static const struct net_device_ops irda_usb_netdev_ops = {
1401         .ndo_open       = irda_usb_net_open,
1402         .ndo_stop       = irda_usb_net_close,
1403         .ndo_do_ioctl   = irda_usb_net_ioctl,
1404         .ndo_start_xmit = irda_usb_hard_xmit,
1405         .ndo_tx_timeout = irda_usb_net_timeout,
1406 };
1407
1408 /*
1409  * Initialise the network side of the irda-usb instance
1410  * Called when a new USB instance is registered in irda_usb_probe()
1411  */
1412 static inline int irda_usb_open(struct irda_usb_cb *self)
1413 {
1414         struct net_device *netdev = self->netdev;
1415
1416         IRDA_DEBUG(1, "%s()\n", __func__);
1417
1418         netdev->netdev_ops = &irda_usb_netdev_ops;
1419
1420         irda_usb_init_qos(self);
1421
1422         return register_netdev(netdev);
1423 }
1424
1425 /*------------------------------------------------------------------*/
1426 /*
1427  * Cleanup the network side of the irda-usb instance
1428  * Called when a USB instance is removed in irda_usb_disconnect()
1429  */
1430 static inline void irda_usb_close(struct irda_usb_cb *self)
1431 {
1432         IRDA_DEBUG(1, "%s()\n", __func__);
1433
1434         /* Remove netdevice */
1435         unregister_netdev(self->netdev);
1436
1437         /* Remove the speed buffer */
1438         kfree(self->speed_buff);
1439         self->speed_buff = NULL;
1440
1441         kfree(self->tx_buff);
1442         self->tx_buff = NULL;
1443 }
1444
1445 /********************** USB CONFIG SUBROUTINES **********************/
1446 /*
1447  * Various subroutines dealing with USB stuff we use to configure and
1448  * initialise each irda-usb instance.
1449  * These functions are used below in the main calls of the driver...
1450  */
1451
1452 /*------------------------------------------------------------------*/
1453 /*
1454  * Function irda_usb_parse_endpoints(dev, ifnum)
1455  *
1456  *    Parse the various endpoints and find the one we need.
1457  *
1458  * The endpoint are the pipes used to communicate with the USB device.
1459  * The spec defines 2 endpoints of type bulk transfer, one in, and one out.
1460  * These are used to pass frames back and forth with the dongle.
1461  * Most dongle have also an interrupt endpoint, that will be probably
1462  * documented in the next spec...
1463  */
1464 static inline int irda_usb_parse_endpoints(struct irda_usb_cb *self, struct usb_host_endpoint *endpoint, int ennum)
1465 {
1466         int i;          /* Endpoint index in table */
1467
1468         /* Init : no endpoints */
1469         self->bulk_in_ep = 0;
1470         self->bulk_out_ep = 0;
1471         self->bulk_int_ep = 0;
1472
1473         /* Let's look at all those endpoints */
1474         for(i = 0; i < ennum; i++) {
1475                 /* All those variables will get optimised by the compiler,
1476                  * so let's aim for clarity... - Jean II */
1477                 __u8 ep;        /* Endpoint address */
1478                 __u8 dir;       /* Endpoint direction */
1479                 __u8 attr;      /* Endpoint attribute */
1480                 __u16 psize;    /* Endpoint max packet size in bytes */
1481
1482                 /* Get endpoint address, direction and attribute */
1483                 ep = endpoint[i].desc.bEndpointAddress & USB_ENDPOINT_NUMBER_MASK;
1484                 dir = endpoint[i].desc.bEndpointAddress & USB_ENDPOINT_DIR_MASK;
1485                 attr = endpoint[i].desc.bmAttributes;
1486                 psize = le16_to_cpu(endpoint[i].desc.wMaxPacketSize);
1487
1488                 /* Is it a bulk endpoint ??? */
1489                 if(attr == USB_ENDPOINT_XFER_BULK) {
1490                         /* We need to find an IN and an OUT */
1491                         if(dir == USB_DIR_IN) {
1492                                 /* This is our Rx endpoint */
1493                                 self->bulk_in_ep = ep;
1494                         } else {
1495                                 /* This is our Tx endpoint */
1496                                 self->bulk_out_ep = ep;
1497                                 self->bulk_out_mtu = psize;
1498                         }
1499                 } else {
1500                         if((attr == USB_ENDPOINT_XFER_INT) &&
1501                            (dir == USB_DIR_IN)) {
1502                                 /* This is our interrupt endpoint */
1503                                 self->bulk_int_ep = ep;
1504                         } else {
1505                                 IRDA_ERROR("%s(), Unrecognised endpoint %02X.\n", __func__, ep);
1506                         }
1507                 }
1508         }
1509
1510         IRDA_DEBUG(0, "%s(), And our endpoints are : in=%02X, out=%02X (%d), int=%02X\n",
1511                 __func__, self->bulk_in_ep, self->bulk_out_ep, self->bulk_out_mtu, self->bulk_int_ep);
1512
1513         return (self->bulk_in_ep != 0) && (self->bulk_out_ep != 0);
1514 }
1515
1516 #ifdef IU_DUMP_CLASS_DESC
1517 /*------------------------------------------------------------------*/
1518 /*
1519  * Function usb_irda_dump_class_desc(desc)
1520  *
1521  *    Prints out the contents of the IrDA class descriptor
1522  *
1523  */
1524 static inline void irda_usb_dump_class_desc(struct irda_class_desc *desc)
1525 {
1526         /* Values are little endian */
1527         printk("bLength=%x\n", desc->bLength);
1528         printk("bDescriptorType=%x\n", desc->bDescriptorType);
1529         printk("bcdSpecRevision=%x\n", le16_to_cpu(desc->bcdSpecRevision));
1530         printk("bmDataSize=%x\n", desc->bmDataSize);
1531         printk("bmWindowSize=%x\n", desc->bmWindowSize);
1532         printk("bmMinTurnaroundTime=%d\n", desc->bmMinTurnaroundTime);
1533         printk("wBaudRate=%x\n", le16_to_cpu(desc->wBaudRate));
1534         printk("bmAdditionalBOFs=%x\n", desc->bmAdditionalBOFs);
1535         printk("bIrdaRateSniff=%x\n", desc->bIrdaRateSniff);
1536         printk("bMaxUnicastList=%x\n", desc->bMaxUnicastList);
1537 }
1538 #endif /* IU_DUMP_CLASS_DESC */
1539
1540 /*------------------------------------------------------------------*/
1541 /*
1542  * Function irda_usb_find_class_desc(intf)
1543  *
1544  *    Returns instance of IrDA class descriptor, or NULL if not found
1545  *
1546  * The class descriptor is some extra info that IrDA USB devices will
1547  * offer to us, describing their IrDA characteristics. We will use that in
1548  * irda_usb_init_qos()
1549  */
1550 static inline struct irda_class_desc *irda_usb_find_class_desc(struct usb_interface *intf)
1551 {
1552         struct usb_device *dev = interface_to_usbdev (intf);
1553         struct irda_class_desc *desc;
1554         int ret;
1555
1556         desc = kzalloc(sizeof(*desc), GFP_KERNEL);
1557         if (!desc)
1558                 return NULL;
1559
1560         /* USB-IrDA class spec 1.0:
1561          *      6.1.3: Standard "Get Descriptor" Device Request is not
1562          *             appropriate to retrieve class-specific descriptor
1563          *      6.2.5: Class Specific "Get Class Descriptor" Interface Request
1564          *             is mandatory and returns the USB-IrDA class descriptor
1565          */
1566
1567         ret = usb_control_msg(dev, usb_rcvctrlpipe(dev,0),
1568                 IU_REQ_GET_CLASS_DESC,
1569                 USB_DIR_IN | USB_TYPE_CLASS | USB_RECIP_INTERFACE,
1570                 0, intf->altsetting->desc.bInterfaceNumber, desc,
1571                 sizeof(*desc), 500);
1572
1573         IRDA_DEBUG(1, "%s(), ret=%d\n", __func__, ret);
1574         if (ret < sizeof(*desc)) {
1575                 IRDA_WARNING("usb-irda: class_descriptor read %s (%d)\n",
1576                              (ret<0) ? "failed" : "too short", ret);
1577         }
1578         else if (desc->bDescriptorType != USB_DT_IRDA) {
1579                 IRDA_WARNING("usb-irda: bad class_descriptor type\n");
1580         }
1581         else {
1582 #ifdef IU_DUMP_CLASS_DESC
1583                 irda_usb_dump_class_desc(desc);
1584 #endif  /* IU_DUMP_CLASS_DESC */
1585
1586                 return desc;
1587         }
1588         kfree(desc);
1589         return NULL;
1590 }
1591
1592 /*********************** USB DEVICE CALLBACKS ***********************/
1593 /*
1594  * Main calls from the USB subsystem.
1595  * Mostly registering a new irda-usb device and removing it....
1596  */
1597
1598 /*------------------------------------------------------------------*/
1599 /*
1600  * This routine is called by the USB subsystem for each new device
1601  * in the system. We need to check if the device is ours, and in
1602  * this case start handling it.
1603  * The USB layer protect us from reentrancy (via BKL), so we don't need
1604  * to spinlock in there... Jean II
1605  */
1606 static int irda_usb_probe(struct usb_interface *intf,
1607                           const struct usb_device_id *id)
1608 {
1609         struct net_device *net;
1610         struct usb_device *dev = interface_to_usbdev(intf);
1611         struct irda_usb_cb *self;
1612         struct usb_host_interface *interface;
1613         struct irda_class_desc *irda_desc;
1614         int ret = -ENOMEM;
1615         int i;          /* Driver instance index / Rx URB index */
1616
1617         /* Note : the probe make sure to call us only for devices that
1618          * matches the list of dongle (top of the file). So, we
1619          * don't need to check if the dongle is really ours.
1620          * Jean II */
1621
1622         IRDA_MESSAGE("IRDA-USB found at address %d, Vendor: %x, Product: %x\n",
1623                      dev->devnum, le16_to_cpu(dev->descriptor.idVendor),
1624                      le16_to_cpu(dev->descriptor.idProduct));
1625
1626         net = alloc_irdadev(sizeof(*self));
1627         if (!net)
1628                 goto err_out;
1629
1630         SET_NETDEV_DEV(net, &intf->dev);
1631         self = netdev_priv(net);
1632         self->netdev = net;
1633         spin_lock_init(&self->lock);
1634         init_timer(&self->rx_defer_timer);
1635
1636         self->capability = id->driver_info;
1637         self->needspatch = ((self->capability & IUC_STIR421X) != 0);
1638
1639         /* Create all of the needed urbs */
1640         if (self->capability & IUC_STIR421X) {
1641                 self->max_rx_urb = IU_SIGMATEL_MAX_RX_URBS;
1642                 self->header_length = USB_IRDA_STIR421X_HEADER;
1643         } else {
1644                 self->max_rx_urb = IU_MAX_RX_URBS;
1645                 self->header_length = USB_IRDA_HEADER;
1646         }
1647
1648         self->rx_urb = kcalloc(self->max_rx_urb, sizeof(struct urb *),
1649                                 GFP_KERNEL);
1650         if (!self->rx_urb)
1651                 goto err_free_net;
1652
1653         for (i = 0; i < self->max_rx_urb; i++) {
1654                 self->rx_urb[i] = usb_alloc_urb(0, GFP_KERNEL);
1655                 if (!self->rx_urb[i]) {
1656                         goto err_out_1;
1657                 }
1658         }
1659         self->tx_urb = usb_alloc_urb(0, GFP_KERNEL);
1660         if (!self->tx_urb) {
1661                 goto err_out_1;
1662         }
1663         self->speed_urb = usb_alloc_urb(0, GFP_KERNEL);
1664         if (!self->speed_urb) {
1665                 goto err_out_2;
1666         }
1667
1668         /* Is this really necessary? (no, except maybe for broken devices) */
1669         if (usb_reset_configuration (dev) < 0) {
1670                 dev_err(&intf->dev, "reset_configuration failed\n");
1671                 ret = -EIO;
1672                 goto err_out_3;
1673         }
1674
1675         /* Is this really necessary? */
1676         /* Note : some driver do hardcode the interface number, some others
1677          * specify an alternate, but very few driver do like this.
1678          * Jean II */
1679         ret = usb_set_interface(dev, intf->altsetting->desc.bInterfaceNumber, 0);
1680         IRDA_DEBUG(1, "usb-irda: set interface %d result %d\n", intf->altsetting->desc.bInterfaceNumber, ret);
1681         switch (ret) {
1682                 case 0:
1683                         break;
1684                 case -EPIPE:            /* -EPIPE = -32 */
1685                         /* Martin Diehl says if we get a -EPIPE we should
1686                          * be fine and we don't need to do a usb_clear_halt().
1687                          * - Jean II */
1688                         IRDA_DEBUG(0, "%s(), Received -EPIPE, ignoring...\n", __func__);
1689                         break;
1690                 default:
1691                         IRDA_DEBUG(0, "%s(), Unknown error %d\n", __func__, ret);
1692                         ret = -EIO;
1693                         goto err_out_3;
1694         }
1695
1696         /* Find our endpoints */
1697         interface = intf->cur_altsetting;
1698         if(!irda_usb_parse_endpoints(self, interface->endpoint,
1699                                      interface->desc.bNumEndpoints)) {
1700                 IRDA_ERROR("%s(), Bogus endpoints...\n", __func__);
1701                 ret = -EIO;
1702                 goto err_out_3;
1703         }
1704
1705         self->usbdev = dev;
1706
1707         /* Find IrDA class descriptor */
1708         irda_desc = irda_usb_find_class_desc(intf);
1709         ret = -ENODEV;
1710         if (!irda_desc)
1711                 goto err_out_3;
1712
1713         if (self->needspatch) {
1714                 ret = usb_control_msg (self->usbdev, usb_sndctrlpipe (self->usbdev, 0),
1715                                        0x02, 0x40, 0, 0, NULL, 0, 500);
1716                 if (ret < 0) {
1717                         IRDA_DEBUG (0, "usb_control_msg failed %d\n", ret);
1718                         goto err_out_3;
1719                 } else {
1720                         mdelay(10);
1721                 }
1722         }
1723
1724         self->irda_desc =  irda_desc;
1725         self->present = 1;
1726         self->netopen = 0;
1727         self->usbintf = intf;
1728
1729         /* Allocate the buffer for speed changes */
1730         /* Don't change this buffer size and allocation without doing
1731          * some heavy and complete testing. Don't ask why :-(
1732          * Jean II */
1733         self->speed_buff = kzalloc(IRDA_USB_SPEED_MTU, GFP_KERNEL);
1734         if (!self->speed_buff)
1735                 goto err_out_3;
1736
1737         self->tx_buff = kzalloc(IRDA_SKB_MAX_MTU + self->header_length,
1738                                 GFP_KERNEL);
1739         if (!self->tx_buff)
1740                 goto err_out_4;
1741
1742         ret = irda_usb_open(self);
1743         if (ret)
1744                 goto err_out_5;
1745
1746         IRDA_MESSAGE("IrDA: Registered device %s\n", net->name);
1747         usb_set_intfdata(intf, self);
1748
1749         if (self->needspatch) {
1750                 /* Now we fetch and upload the firmware patch */
1751                 ret = stir421x_patch_device(self);
1752                 self->needspatch = (ret < 0);
1753                 if (self->needspatch) {
1754                         IRDA_ERROR("STIR421X: Couldn't upload patch\n");
1755                         goto err_out_6;
1756                 }
1757
1758                 /* replace IrDA class descriptor with what patched device is now reporting */
1759                 irda_desc = irda_usb_find_class_desc (self->usbintf);
1760                 if (!irda_desc) {
1761                         ret = -ENODEV;
1762                         goto err_out_6;
1763                 }
1764                 kfree(self->irda_desc);
1765                 self->irda_desc = irda_desc;
1766                 irda_usb_init_qos(self);
1767         }
1768
1769         return 0;
1770 err_out_6:
1771         unregister_netdev(self->netdev);
1772 err_out_5:
1773         kfree(self->tx_buff);
1774 err_out_4:
1775         kfree(self->speed_buff);
1776 err_out_3:
1777         /* Free all urbs that we may have created */
1778         usb_free_urb(self->speed_urb);
1779 err_out_2:
1780         usb_free_urb(self->tx_urb);
1781 err_out_1:
1782         for (i = 0; i < self->max_rx_urb; i++)
1783                 usb_free_urb(self->rx_urb[i]);
1784         kfree(self->rx_urb);
1785 err_free_net:
1786         free_netdev(net);
1787 err_out:
1788         return ret;
1789 }
1790
1791 /*------------------------------------------------------------------*/
1792 /*
1793  * The current irda-usb device is removed, the USB layer tell us
1794  * to shut it down...
1795  * One of the constraints is that when we exit this function,
1796  * we cannot use the usb_device no more. Gone. Destroyed. kfree().
1797  * Most other subsystem allow you to destroy the instance at a time
1798  * when it's convenient to you, to postpone it to a later date, but
1799  * not the USB subsystem.
1800  * So, we must make bloody sure that everything gets deactivated.
1801  * Jean II
1802  */
1803 static void irda_usb_disconnect(struct usb_interface *intf)
1804 {
1805         unsigned long flags;
1806         struct irda_usb_cb *self = usb_get_intfdata(intf);
1807         int i;
1808
1809         IRDA_DEBUG(1, "%s()\n", __func__);
1810
1811         usb_set_intfdata(intf, NULL);
1812         if (!self)
1813                 return;
1814
1815         /* Make sure that the Tx path is not executing. - Jean II */
1816         spin_lock_irqsave(&self->lock, flags);
1817
1818         /* Oups ! We are not there any more.
1819          * This will stop/desactivate the Tx path. - Jean II */
1820         self->present = 0;
1821
1822         /* Kill defered Rx URB */
1823         del_timer(&self->rx_defer_timer);
1824
1825         /* We need to have irq enabled to unlink the URBs. That's OK,
1826          * at this point the Tx path is gone - Jean II */
1827         spin_unlock_irqrestore(&self->lock, flags);
1828
1829         /* Hum... Check if networking is still active (avoid races) */
1830         if((self->netopen) || (self->irlap)) {
1831                 /* Accept no more transmissions */
1832                 /*netif_device_detach(self->netdev);*/
1833                 netif_stop_queue(self->netdev);
1834                 /* Stop all the receive URBs. Must be synchronous. */
1835                 for (i = 0; i < self->max_rx_urb; i++)
1836                         usb_kill_urb(self->rx_urb[i]);
1837                 /* Cancel Tx and speed URB.
1838                  * Make sure it's synchronous to avoid races. */
1839                 usb_kill_urb(self->tx_urb);
1840                 usb_kill_urb(self->speed_urb);
1841         }
1842
1843         /* Cleanup the device stuff */
1844         irda_usb_close(self);
1845         /* No longer attached to USB bus */
1846         self->usbdev = NULL;
1847         self->usbintf = NULL;
1848
1849         /* Clean up our urbs */
1850         for (i = 0; i < self->max_rx_urb; i++)
1851                 usb_free_urb(self->rx_urb[i]);
1852         kfree(self->rx_urb);
1853         /* Clean up Tx and speed URB */
1854         usb_free_urb(self->tx_urb);
1855         usb_free_urb(self->speed_urb);
1856
1857         /* Free self and network device */
1858         free_netdev(self->netdev);
1859         IRDA_DEBUG(0, "%s(), USB IrDA Disconnected\n", __func__);
1860 }
1861
1862 #ifdef CONFIG_PM
1863 /* USB suspend, so power off the transmitter/receiver */
1864 static int irda_usb_suspend(struct usb_interface *intf, pm_message_t message)
1865 {
1866         struct irda_usb_cb *self = usb_get_intfdata(intf);
1867         int i;
1868
1869         netif_device_detach(self->netdev);
1870
1871         if (self->tx_urb != NULL)
1872                 usb_kill_urb(self->tx_urb);
1873         if (self->speed_urb != NULL)
1874                 usb_kill_urb(self->speed_urb);
1875         for (i = 0; i < self->max_rx_urb; i++) {
1876                 if (self->rx_urb[i] != NULL)
1877                         usb_kill_urb(self->rx_urb[i]);
1878         }
1879         return 0;
1880 }
1881
1882 /* Coming out of suspend, so reset hardware */
1883 static int irda_usb_resume(struct usb_interface *intf)
1884 {
1885         struct irda_usb_cb *self = usb_get_intfdata(intf);
1886         int i;
1887
1888         for (i = 0; i < self->max_rx_urb; i++) {
1889                 if (self->rx_urb[i] != NULL)
1890                         usb_submit_urb(self->rx_urb[i], GFP_KERNEL);
1891         }
1892
1893         netif_device_attach(self->netdev);
1894         return 0;
1895 }
1896 #endif
1897
1898 /*------------------------------------------------------------------*/
1899 /*
1900  * USB device callbacks
1901  */
1902 static struct usb_driver irda_driver = {
1903         .name           = "irda-usb",
1904         .probe          = irda_usb_probe,
1905         .disconnect     = irda_usb_disconnect,
1906         .id_table       = dongles,
1907 #ifdef CONFIG_PM
1908         .suspend        = irda_usb_suspend,
1909         .resume         = irda_usb_resume,
1910 #endif
1911 };
1912
1913 module_usb_driver(irda_driver);
1914
1915 /*
1916  * Module parameters
1917  */
1918 module_param(qos_mtt_bits, int, 0);
1919 MODULE_PARM_DESC(qos_mtt_bits, "Minimum Turn Time");
1920 MODULE_AUTHOR("Roman Weissgaerber <weissg@vienna.at>, Dag Brattli <dag@brattli.net>, Jean Tourrilhes <jt@hpl.hp.com> and Nick Fedchik <nick@fedchik.org.ua>");
1921 MODULE_DESCRIPTION("IrDA-USB Dongle Driver");
1922 MODULE_LICENSE("GPL");