drivers/net/ethernet/stmicro/stmmac/stmmac_main.c

   1 /*******************************************************************************
   2   This is the driver for the ST MAC 10/100/1000 on-chip Ethernet controllers.
   3   ST Ethernet IPs are built around a Synopsys IP Core.
   4
   5         Copyright(C) 2007-2011 STMicroelectronics Ltd
   6
   7   This program is free software; you can redistribute it and/or modify it
   8   under the terms and conditions of the GNU General Public License,
   9   version 2, as published by the Free Software Foundation.
  10
  11   This program is distributed in the hope it will be useful, but WITHOUT
  12   ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  13   FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  14   more details.
  15
  16   You should have received a copy of the GNU General Public License along with
  17   this program; if not, write to the Free Software Foundation, Inc.,
  18   51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
  19
  20   The full GNU General Public License is included in this distribution in
  21   the file called "COPYING".
  22
  23   Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
  24
  25   Documentation available at:
  26         http://www.stlinux.com
  27   Support available at:
  28         https://bugzilla.stlinux.com/
  29 *******************************************************************************/
  30
  31 #include <linux/kernel.h>
  32 #include <linux/interrupt.h>
  33 #include <linux/ip.h>
  34 #include <linux/tcp.h>
  35 #include <linux/skbuff.h>
  36 #include <linux/ethtool.h>
  37 #include <linux/if_ether.h>
  38 #include <linux/crc32.h>
  39 #include <linux/mii.h>
  40 #include <linux/if.h>
  41 #include <linux/if_vlan.h>
  42 #include <linux/dma-mapping.h>
  43 #include <linux/slab.h>
  44 #include <linux/prefetch.h>
  45 #ifdef CONFIG_STMMAC_DEBUG_FS
  46 #include <linux/debugfs.h>
  47 #include <linux/seq_file.h>
  48 #endif
  49 #include "stmmac.h"
  50
  51 #undef STMMAC_DEBUG
  52 /*#define STMMAC_DEBUG*/
  53 #ifdef STMMAC_DEBUG
  54 #define DBG(nlevel, klevel, fmt, args...) \
  55                 ((void)(netif_msg_##nlevel(priv) && \
  56                 printk(KERN_##klevel fmt, ## args)))
  57 #else
  58 #define DBG(nlevel, klevel, fmt, args...) do { } while (0)
  59 #endif
  60
  61 #undef STMMAC_RX_DEBUG
  62 /*#define STMMAC_RX_DEBUG*/
  63 #ifdef STMMAC_RX_DEBUG
  64 #define RX_DBG(fmt, args...)  printk(fmt, ## args)
  65 #else
  66 #define RX_DBG(fmt, args...)  do { } while (0)
  67 #endif
  68
  69 #undef STMMAC_XMIT_DEBUG
  70 /*#define STMMAC_XMIT_DEBUG*/
  71 #ifdef STMMAC_TX_DEBUG
  72 #define TX_DBG(fmt, args...)  printk(fmt, ## args)
  73 #else
  74 #define TX_DBG(fmt, args...)  do { } while (0)
  75 #endif
  76
  77 #define STMMAC_ALIGN(x) L1_CACHE_ALIGN(x)
  78 #define JUMBO_LEN       9000
  79
  80 /* Module parameters */
  81 #define TX_TIMEO 5000 /* default 5 seconds */
  82 static int watchdog = TX_TIMEO;
  83 module_param(watchdog, int, S_IRUGO | S_IWUSR);
  84 MODULE_PARM_DESC(watchdog, "Transmit timeout in milliseconds");
  85
  86 static int debug = -1;          /* -1: default, 0: no output, 16:  all */
  87 module_param(debug, int, S_IRUGO | S_IWUSR);
  88 MODULE_PARM_DESC(debug, "Message Level (0: no output, 16: all)");
  89
  90 int phyaddr = -1;
  91 module_param(phyaddr, int, S_IRUGO);
  92 MODULE_PARM_DESC(phyaddr, "Physical device address");
  93
  94 #define DMA_TX_SIZE 256
  95 static int dma_txsize = DMA_TX_SIZE;
  96 module_param(dma_txsize, int, S_IRUGO | S_IWUSR);
  97 MODULE_PARM_DESC(dma_txsize, "Number of descriptors in the TX list");
  98
  99 #define DMA_RX_SIZE 256
 100 static int dma_rxsize = DMA_RX_SIZE;
 101 module_param(dma_rxsize, int, S_IRUGO | S_IWUSR);
 102 MODULE_PARM_DESC(dma_rxsize, "Number of descriptors in the RX list");
 103
 104 static int flow_ctrl = FLOW_OFF;
 105 module_param(flow_ctrl, int, S_IRUGO | S_IWUSR);
 106 MODULE_PARM_DESC(flow_ctrl, "Flow control ability [on/off]");
 107
 108 static int pause = PAUSE_TIME;
 109 module_param(pause, int, S_IRUGO | S_IWUSR);
 110 MODULE_PARM_DESC(pause, "Flow Control Pause Time");
 111
 112 #define TC_DEFAULT 64
 113 static int tc = TC_DEFAULT;
 114 module_param(tc, int, S_IRUGO | S_IWUSR);
 115 MODULE_PARM_DESC(tc, "DMA threshold control value");
 116
 117 /* Pay attention to tune this parameter; take care of both
 118  * hardware capability and network stabitily/performance impact.
 119  * Many tests showed that ~4ms latency seems to be good enough. */
 120 #ifdef CONFIG_STMMAC_TIMER
 121 #define DEFAULT_PERIODIC_RATE   256
 122 static int tmrate = DEFAULT_PERIODIC_RATE;
 123 module_param(tmrate, int, S_IRUGO | S_IWUSR);
 124 MODULE_PARM_DESC(tmrate, "External timer freq. (default: 256Hz)");
 125 #endif
 126
 127 #define DMA_BUFFER_SIZE BUF_SIZE_2KiB
 128 static int buf_sz = DMA_BUFFER_SIZE;
 129 module_param(buf_sz, int, S_IRUGO | S_IWUSR);
 130 MODULE_PARM_DESC(buf_sz, "DMA buffer size");
 131
 132 static const u32 default_msg_level = (NETIF_MSG_DRV | NETIF_MSG_PROBE |
 133                                       NETIF_MSG_LINK | NETIF_MSG_IFUP |
 134                                       NETIF_MSG_IFDOWN | NETIF_MSG_TIMER);
 135
 136 static irqreturn_t stmmac_interrupt(int irq, void *dev_id);
 137
 138 #ifdef CONFIG_STMMAC_DEBUG_FS
 139 static int stmmac_init_fs(struct net_device *dev);
 140 static void stmmac_exit_fs(void);
 141 #endif
 142
 143 /**
 144  * stmmac_verify_args - verify the driver parameters.
 145  * Description: it verifies if some wrong parameter is passed to the driver.
 146  * Note that wrong parameters are replaced with the default values.
 147  */
 148 static void stmmac_verify_args(void)
 149 {
 150         if (unlikely(watchdog < 0))
 151                 watchdog = TX_TIMEO;
 152         if (unlikely(dma_rxsize < 0))
 153                 dma_rxsize = DMA_RX_SIZE;
 154         if (unlikely(dma_txsize < 0))
 155                 dma_txsize = DMA_TX_SIZE;
 156         if (unlikely((buf_sz < DMA_BUFFER_SIZE) || (buf_sz > BUF_SIZE_16KiB)))
 157                 buf_sz = DMA_BUFFER_SIZE;
 158         if (unlikely(flow_ctrl > 1))
 159                 flow_ctrl = FLOW_AUTO;
 160         else if (likely(flow_ctrl < 0))
 161                 flow_ctrl = FLOW_OFF;
 162         if (unlikely((pause < 0) || (pause > 0xffff)))
 163                 pause = PAUSE_TIME;
 164 }
 165
 166 #if defined(STMMAC_XMIT_DEBUG) || defined(STMMAC_RX_DEBUG)
 167 static void print_pkt(unsigned char *buf, int len)
 168 {
 169         int j;
 170         pr_info("len = %d byte, buf addr: 0x%p", len, buf);
 171         for (j = 0; j < len; j++) {
 172                 if ((j % 16) == 0)
 173                         pr_info("\n %03x:", j);
 174                 pr_info(" %02x", buf[j]);
 175         }
 176         pr_info("\n");
 177 }
 178 #endif
 179
 180 /* minimum number of free TX descriptors required to wake up TX process */
 181 #define STMMAC_TX_THRESH(x)     (x->dma_tx_size/4)
 182
 183 static inline u32 stmmac_tx_avail(struct stmmac_priv *priv)
 184 {
 185         return priv->dirty_tx + priv->dma_tx_size - priv->cur_tx - 1;
 186 }
 187
 188 /* On some ST platforms, some HW system configuraton registers have to be
 189  * set according to the link speed negotiated.
 190  */
 191 static inline void stmmac_hw_fix_mac_speed(struct stmmac_priv *priv)
 192 {
 193         struct phy_device *phydev = priv->phydev;
 194
 195         if (likely(priv->plat->fix_mac_speed))
 196                 priv->plat->fix_mac_speed(priv->plat->bsp_priv,
 197                                           phydev->speed);
 198 }
 199
 200 /**
 201  * stmmac_adjust_link
 202  * @dev: net device structure
 203  * Description: it adjusts the link parameters.
 204  */
 205 static void stmmac_adjust_link(struct net_device *dev)
 206 {
 207         struct stmmac_priv *priv = netdev_priv(dev);
 208         struct phy_device *phydev = priv->phydev;
 209         unsigned long flags;
 210         int new_state = 0;
 211         unsigned int fc = priv->flow_ctrl, pause_time = priv->pause;
 212
 213         if (phydev == NULL)
 214                 return;
 215
 216         DBG(probe, DEBUG, "stmmac_adjust_link: called.  address %d link %d\n",
 217             phydev->addr, phydev->link);
 218
 219         spin_lock_irqsave(&priv->lock, flags);
 220         if (phydev->link) {
 221                 u32 ctrl = readl(priv->ioaddr + MAC_CTRL_REG);
 222
 223                 /* Now we make sure that we can be in full duplex mode.
 224                  * If not, we operate in half-duplex mode. */
 225                 if (phydev->duplex != priv->oldduplex) {
 226                         new_state = 1;
 227                         if (!(phydev->duplex))
 228                                 ctrl &= ~priv->hw->link.duplex;
 229                         else
 230                                 ctrl |= priv->hw->link.duplex;
 231                         priv->oldduplex = phydev->duplex;
 232                 }
 233                 /* Flow Control operation */
 234                 if (phydev->pause)
 235                         priv->hw->mac->flow_ctrl(priv->ioaddr, phydev->duplex,
 236                                                  fc, pause_time);
 237
 238                 if (phydev->speed != priv->speed) {
 239                         new_state = 1;
 240                         switch (phydev->speed) {
 241                         case 1000:
 242                                 if (likely(priv->plat->has_gmac))
 243                                         ctrl &= ~priv->hw->link.port;
 244                                         stmmac_hw_fix_mac_speed(priv);
 245                                 break;
 246                         case 100:
 247                         case 10:
 248                                 if (priv->plat->has_gmac) {
 249                                         ctrl |= priv->hw->link.port;
 250                                         if (phydev->speed == SPEED_100) {
 251                                                 ctrl |= priv->hw->link.speed;
 252                                         } else {
 253                                                 ctrl &= ~(priv->hw->link.speed);
 254                                         }
 255                                 } else {
 256                                         ctrl &= ~priv->hw->link.port;
 257                                 }
 258                                 stmmac_hw_fix_mac_speed(priv);
 259                                 break;
 260                         default:
 261                                 if (netif_msg_link(priv))
 262                                         pr_warning("%s: Speed (%d) is not 10"
 263                                        " or 100!\n", dev->name, phydev->speed);
 264                                 break;
 265                         }
 266
 267                         priv->speed = phydev->speed;
 268                 }
 269
 270                 writel(ctrl, priv->ioaddr + MAC_CTRL_REG);
 271
 272                 if (!priv->oldlink) {
 273                         new_state = 1;
 274                         priv->oldlink = 1;
 275                 }
 276         } else if (priv->oldlink) {
 277                 new_state = 1;
 278                 priv->oldlink = 0;
 279                 priv->speed = 0;
 280                 priv->oldduplex = -1;
 281         }
 282
 283         if (new_state && netif_msg_link(priv))
 284                 phy_print_status(phydev);
 285
 286         spin_unlock_irqrestore(&priv->lock, flags);
 287
 288         DBG(probe, DEBUG, "stmmac_adjust_link: exiting\n");
 289 }
 290
 291 /**
 292  * stmmac_init_phy - PHY initialization
 293  * @dev: net device structure
 294  * Description: it initializes the driver's PHY state, and attaches the PHY
 295  * to the mac driver.
 296  *  Return value:
 297  *  0 on success
 298  */
 299 static int stmmac_init_phy(struct net_device *dev)
 300 {
 301         struct stmmac_priv *priv = netdev_priv(dev);
 302         struct phy_device *phydev;
 303         char phy_id[MII_BUS_ID_SIZE + 3];
 304         char bus_id[MII_BUS_ID_SIZE];
 305         int interface = priv->plat->interface;
 306         priv->oldlink = 0;
 307         priv->speed = 0;
 308         priv->oldduplex = -1;
 309
 310         snprintf(bus_id, MII_BUS_ID_SIZE, "stmmac-%x", priv->plat->bus_id);
 311         snprintf(phy_id, MII_BUS_ID_SIZE + 3, PHY_ID_FMT, bus_id,
 312                  priv->plat->phy_addr);
 313         pr_debug("stmmac_init_phy:  trying to attach to %s\n", phy_id);
 314
 315         phydev = phy_connect(dev, phy_id, &stmmac_adjust_link, 0, interface);
 316
 317         if (IS_ERR(phydev)) {
 318                 pr_err("%s: Could not attach to PHY\n", dev->name);
 319                 return PTR_ERR(phydev);
 320         }
 321
 322         /* Stop Advertising 1000BASE Capability if interface is not GMII */
 323         if ((interface == PHY_INTERFACE_MODE_MII) ||
 324             (interface == PHY_INTERFACE_MODE_RMII))
 325                 phydev->advertising &= ~(SUPPORTED_1000baseT_Half |
 326                                          SUPPORTED_1000baseT_Full);
 327
 328         /*
 329          * Broken HW is sometimes missing the pull-up resistor on the
 330          * MDIO line, which results in reads to non-existent devices returning
 331          * 0 rather than 0xffff. Catch this here and treat 0 as a non-existent
 332          * device as well.
 333          * Note: phydev->phy_id is the result of reading the UID PHY registers.
 334          */
 335         if (phydev->phy_id == 0) {
 336                 phy_disconnect(phydev);
 337                 return -ENODEV;
 338         }
 339         pr_debug("stmmac_init_phy:  %s: attached to PHY (UID 0x%x)"
 340                  " Link = %d\n", dev->name, phydev->phy_id, phydev->link);
 341
 342         priv->phydev = phydev;
 343
 344         return 0;
 345 }
 346
 347 /**
 348  * display_ring
 349  * @p: pointer to the ring.
 350  * @size: size of the ring.
 351  * Description: display all the descriptors within the ring.
 352  */
 353 static void display_ring(struct dma_desc *p, int size)
 354 {
 355         struct tmp_s {
 356                 u64 a;
 357                 unsigned int b;
 358                 unsigned int c;
 359         };
 360         int i;
 361         for (i = 0; i < size; i++) {
 362                 struct tmp_s *x = (struct tmp_s *)(p + i);
 363                 pr_info("\t%d [0x%x]: DES0=0x%x DES1=0x%x BUF1=0x%x BUF2=0x%x",
 364                        i, (unsigned int)virt_to_phys(&p[i]),
 365                        (unsigned int)(x->a), (unsigned int)((x->a) >> 32),
 366                        x->b, x->c);
 367                 pr_info("\n");
 368         }
 369 }
 370
 371 static int stmmac_set_bfsize(int mtu, int bufsize)
 372 {
 373         int ret = bufsize;
 374
 375         if (mtu >= BUF_SIZE_4KiB)
 376                 ret = BUF_SIZE_8KiB;
 377         else if (mtu >= BUF_SIZE_2KiB)
 378                 ret = BUF_SIZE_4KiB;
 379         else if (mtu >= DMA_BUFFER_SIZE)
 380                 ret = BUF_SIZE_2KiB;
 381         else
 382                 ret = DMA_BUFFER_SIZE;
 383
 384         return ret;
 385 }
 386
 387 /**
 388  * init_dma_desc_rings - init the RX/TX descriptor rings
 389  * @dev: net device structure
 390  * Description:  this function initializes the DMA RX/TX descriptors
 391  * and allocates the socket buffers. It suppors the chained and ring
 392  * modes.
 393  */
 394 static void init_dma_desc_rings(struct net_device *dev)
 395 {
 396         int i;
 397         struct stmmac_priv *priv = netdev_priv(dev);
 398         struct sk_buff *skb;
 399         unsigned int txsize = priv->dma_tx_size;
 400         unsigned int rxsize = priv->dma_rx_size;
 401         unsigned int bfsize;
 402         int dis_ic = 0;
 403         int des3_as_data_buf = 0;
 404
 405         /* Set the max buffer size according to the DESC mode
 406          * and the MTU. Note that RING mode allows 16KiB bsize. */
 407         bfsize = priv->hw->ring->set_16kib_bfsize(dev->mtu);
 408
 409         if (bfsize == BUF_SIZE_16KiB)
 410                 des3_as_data_buf = 1;
 411         else
 412                 bfsize = stmmac_set_bfsize(dev->mtu, priv->dma_buf_sz);
 413
 414 #ifdef CONFIG_STMMAC_TIMER
 415         /* Disable interrupts on completion for the reception if timer is on */
 416         if (likely(priv->tm->enable))
 417                 dis_ic = 1;
 418 #endif
 419
 420         DBG(probe, INFO, "stmmac: txsize %d, rxsize %d, bfsize %d\n",
 421             txsize, rxsize, bfsize);
 422
 423         priv->rx_skbuff_dma = kmalloc(rxsize * sizeof(dma_addr_t), GFP_KERNEL);
 424         priv->rx_skbuff =
 425             kmalloc(sizeof(struct sk_buff *) * rxsize, GFP_KERNEL);
 426         priv->dma_rx =
 427             (struct dma_desc *)dma_alloc_coherent(priv->device,
 428                                                   rxsize *
 429                                                   sizeof(struct dma_desc),
 430                                                   &priv->dma_rx_phy,
 431                                                   GFP_KERNEL);
 432         priv->tx_skbuff = kmalloc(sizeof(struct sk_buff *) * txsize,
 433                                        GFP_KERNEL);
 434         priv->dma_tx =
 435             (struct dma_desc *)dma_alloc_coherent(priv->device,
 436                                                   txsize *
 437                                                   sizeof(struct dma_desc),
 438                                                   &priv->dma_tx_phy,
 439                                                   GFP_KERNEL);
 440
 441         if ((priv->dma_rx == NULL) || (priv->dma_tx == NULL)) {
 442                 pr_err("%s:ERROR allocating the DMA Tx/Rx desc\n", __func__);
 443                 return;
 444         }
 445
 446         DBG(probe, INFO, "stmmac (%s) DMA desc: virt addr (Rx %p, "
 447             "Tx %p)\n\tDMA phy addr (Rx 0x%08x, Tx 0x%08x)\n",
 448             dev->name, priv->dma_rx, priv->dma_tx,
 449             (unsigned int)priv->dma_rx_phy, (unsigned int)priv->dma_tx_phy);
 450
 451         /* RX INITIALIZATION */
 452         DBG(probe, INFO, "stmmac: SKB addresses:\n"
 453                          "skb\t\tskb data\tdma data\n");
 454
 455         for (i = 0; i < rxsize; i++) {
 456                 struct dma_desc *p = priv->dma_rx + i;
 457
 458                 skb = __netdev_alloc_skb(dev, bfsize + NET_IP_ALIGN,
 459                                          GFP_KERNEL);
 460                 if (unlikely(skb == NULL)) {
 461                         pr_err("%s: Rx init fails; skb is NULL\n", __func__);
 462                         break;
 463                 }
 464                 skb_reserve(skb, NET_IP_ALIGN);
 465                 priv->rx_skbuff[i] = skb;
 466                 priv->rx_skbuff_dma[i] = dma_map_single(priv->device, skb->data,
 467                                                 bfsize, DMA_FROM_DEVICE);
 468
 469                 p->des2 = priv->rx_skbuff_dma[i];
 470
 471                 priv->hw->ring->init_desc3(des3_as_data_buf, p);
 472
 473                 DBG(probe, INFO, "[%p]\t[%p]\t[%x]\n", priv->rx_skbuff[i],
 474                         priv->rx_skbuff[i]->data, priv->rx_skbuff_dma[i]);
 475         }
 476         priv->cur_rx = 0;
 477         priv->dirty_rx = (unsigned int)(i - rxsize);
 478         priv->dma_buf_sz = bfsize;
 479         buf_sz = bfsize;
 480
 481         /* TX INITIALIZATION */
 482         for (i = 0; i < txsize; i++) {
 483                 priv->tx_skbuff[i] = NULL;
 484                 priv->dma_tx[i].des2 = 0;
 485         }
 486
 487         /* In case of Chained mode this sets the des3 to the next
 488          * element in the chain */
 489         priv->hw->ring->init_dma_chain(priv->dma_rx, priv->dma_rx_phy, rxsize);
 490         priv->hw->ring->init_dma_chain(priv->dma_tx, priv->dma_tx_phy, txsize);
 491
 492         priv->dirty_tx = 0;
 493         priv->cur_tx = 0;
 494
 495         /* Clear the Rx/Tx descriptors */
 496         priv->hw->desc->init_rx_desc(priv->dma_rx, rxsize, dis_ic);
 497         priv->hw->desc->init_tx_desc(priv->dma_tx, txsize);
 498
 499         if (netif_msg_hw(priv)) {
 500                 pr_info("RX descriptor ring:\n");
 501                 display_ring(priv->dma_rx, rxsize);
 502                 pr_info("TX descriptor ring:\n");
 503                 display_ring(priv->dma_tx, txsize);
 504         }
 505 }
 506
 507 static void dma_free_rx_skbufs(struct stmmac_priv *priv)
 508 {
 509         int i;
 510
 511         for (i = 0; i < priv->dma_rx_size; i++) {
 512                 if (priv->rx_skbuff[i]) {
 513                         dma_unmap_single(priv->device, priv->rx_skbuff_dma[i],
 514                                          priv->dma_buf_sz, DMA_FROM_DEVICE);
 515                         dev_kfree_skb_any(priv->rx_skbuff[i]);
 516                 }
 517                 priv->rx_skbuff[i] = NULL;
 518         }
 519 }
 520
 521 static void dma_free_tx_skbufs(struct stmmac_priv *priv)
 522 {
 523         int i;
 524
 525         for (i = 0; i < priv->dma_tx_size; i++) {
 526                 if (priv->tx_skbuff[i] != NULL) {
 527                         struct dma_desc *p = priv->dma_tx + i;
 528                         if (p->des2)
 529                                 dma_unmap_single(priv->device, p->des2,
 530                                                  priv->hw->desc->get_tx_len(p),
 531                                                  DMA_TO_DEVICE);
 532                         dev_kfree_skb_any(priv->tx_skbuff[i]);
 533                         priv->tx_skbuff[i] = NULL;
 534                 }
 535         }
 536 }
 537
 538 static void free_dma_desc_resources(struct stmmac_priv *priv)
 539 {
 540         /* Release the DMA TX/RX socket buffers */
 541         dma_free_rx_skbufs(priv);
 542         dma_free_tx_skbufs(priv);
 543
 544         /* Free the region of consistent memory previously allocated for
 545          * the DMA */
 546         dma_free_coherent(priv->device,
 547                           priv->dma_tx_size * sizeof(struct dma_desc),
 548                           priv->dma_tx, priv->dma_tx_phy);
 549         dma_free_coherent(priv->device,
 550                           priv->dma_rx_size * sizeof(struct dma_desc),
 551                           priv->dma_rx, priv->dma_rx_phy);
 552         kfree(priv->rx_skbuff_dma);
 553         kfree(priv->rx_skbuff);
 554         kfree(priv->tx_skbuff);
 555 }
 556
 557 /**
 558  *  stmmac_dma_operation_mode - HW DMA operation mode
 559  *  @priv : pointer to the private device structure.
 560  *  Description: it sets the DMA operation mode: tx/rx DMA thresholds
 561  *  or Store-And-Forward capability.
 562  */
 563 static void stmmac_dma_operation_mode(struct stmmac_priv *priv)
 564 {
 565         if (likely(priv->plat->force_sf_dma_mode ||
 566                 ((priv->plat->tx_coe) && (!priv->no_csum_insertion)))) {
 567                 /*
 568                  * In case of GMAC, SF mode can be enabled
 569                  * to perform the TX COE in HW. This depends on:
 570                  * 1) TX COE if actually supported
 571                  * 2) There is no bugged Jumbo frame support
 572                  *    that needs to not insert csum in the TDES.
 573                  */
 574                 priv->hw->dma->dma_mode(priv->ioaddr,
 575                                         SF_DMA_MODE, SF_DMA_MODE);
 576                 tc = SF_DMA_MODE;
 577         } else
 578                 priv->hw->dma->dma_mode(priv->ioaddr, tc, SF_DMA_MODE);
 579 }
 580
 581 /**
 582  * stmmac_tx:
 583  * @priv: private driver structure
 584  * Description: it reclaims resources after transmission completes.
 585  */
 586 static void stmmac_tx(struct stmmac_priv *priv)
 587 {
 588         unsigned int txsize = priv->dma_tx_size;
 589
 590         spin_lock(&priv->tx_lock);
 591
 592         while (priv->dirty_tx != priv->cur_tx) {
 593                 int last;
 594                 unsigned int entry = priv->dirty_tx % txsize;
 595                 struct sk_buff *skb = priv->tx_skbuff[entry];
 596                 struct dma_desc *p = priv->dma_tx + entry;
 597
 598                 /* Check if the descriptor is owned by the DMA. */
 599                 if (priv->hw->desc->get_tx_owner(p))
 600                         break;
 601
 602                 /* Verify tx error by looking at the last segment */
 603                 last = priv->hw->desc->get_tx_ls(p);
 604                 if (likely(last)) {
 605                         int tx_error =
 606                                 priv->hw->desc->tx_status(&priv->dev->stats,
 607                                                           &priv->xstats, p,
 608                                                           priv->ioaddr);
 609                         if (likely(tx_error == 0)) {
 610                                 priv->dev->stats.tx_packets++;
 611                                 priv->xstats.tx_pkt_n++;
 612                         } else
 613                                 priv->dev->stats.tx_errors++;
 614                 }
 615                 TX_DBG("%s: curr %d, dirty %d\n", __func__,
 616                         priv->cur_tx, priv->dirty_tx);
 617
 618                 if (likely(p->des2))
 619                         dma_unmap_single(priv->device, p->des2,
 620                                          priv->hw->desc->get_tx_len(p),
 621                                          DMA_TO_DEVICE);
 622                 priv->hw->ring->clean_desc3(p);
 623
 624                 if (likely(skb != NULL)) {
 625                         /*
 626                          * If there's room in the queue (limit it to size)
 627                          * we add this skb back into the pool,
 628                          * if it's the right size.
 629                          */
 630                         if ((skb_queue_len(&priv->rx_recycle) <
 631                                 priv->dma_rx_size) &&
 632                                 skb_recycle_check(skb, priv->dma_buf_sz))
 633                                 __skb_queue_head(&priv->rx_recycle, skb);
 634                         else
 635                                 dev_kfree_skb(skb);
 636
 637                         priv->tx_skbuff[entry] = NULL;
 638                 }
 639
 640                 priv->hw->desc->release_tx_desc(p);
 641
 642                 entry = (++priv->dirty_tx) % txsize;
 643         }
 644         if (unlikely(netif_queue_stopped(priv->dev) &&
 645                      stmmac_tx_avail(priv) > STMMAC_TX_THRESH(priv))) {
 646                 netif_tx_lock(priv->dev);
 647                 if (netif_queue_stopped(priv->dev) &&
 648                      stmmac_tx_avail(priv) > STMMAC_TX_THRESH(priv)) {
 649                         TX_DBG("%s: restart transmit\n", __func__);
 650                         netif_wake_queue(priv->dev);
 651                 }
 652                 netif_tx_unlock(priv->dev);
 653         }
 654         spin_unlock(&priv->tx_lock);
 655 }
 656
 657 static inline void stmmac_enable_irq(struct stmmac_priv *priv)
 658 {
 659 #ifdef CONFIG_STMMAC_TIMER
 660         if (likely(priv->tm->enable))
 661                 priv->tm->timer_start(tmrate);
 662         else
 663 #endif
 664                 priv->hw->dma->enable_dma_irq(priv->ioaddr);
 665 }
 666
 667 static inline void stmmac_disable_irq(struct stmmac_priv *priv)
 668 {
 669 #ifdef CONFIG_STMMAC_TIMER
 670         if (likely(priv->tm->enable))
 671                 priv->tm->timer_stop();
 672         else
 673 #endif
 674                 priv->hw->dma->disable_dma_irq(priv->ioaddr);
 675 }
 676
 677 static int stmmac_has_work(struct stmmac_priv *priv)
 678 {
 679         unsigned int has_work = 0;
 680         int rxret, tx_work = 0;
 681
 682         rxret = priv->hw->desc->get_rx_owner(priv->dma_rx +
 683                 (priv->cur_rx % priv->dma_rx_size));
 684
 685         if (priv->dirty_tx != priv->cur_tx)
 686                 tx_work = 1;
 687
 688         if (likely(!rxret || tx_work))
 689                 has_work = 1;
 690
 691         return has_work;
 692 }
 693
 694 static inline void _stmmac_schedule(struct stmmac_priv *priv)
 695 {
 696         if (likely(stmmac_has_work(priv))) {
 697                 stmmac_disable_irq(priv);
 698                 napi_schedule(&priv->napi);
 699         }
 700 }
 701
 702 #ifdef CONFIG_STMMAC_TIMER
 703 void stmmac_schedule(struct net_device *dev)
 704 {
 705         struct stmmac_priv *priv = netdev_priv(dev);
 706
 707         priv->xstats.sched_timer_n++;
 708
 709         _stmmac_schedule(priv);
 710 }
 711
 712 static void stmmac_no_timer_started(unsigned int x)
 713 {;
 714 };
 715
 716 static void stmmac_no_timer_stopped(void)
 717 {;
 718 };
 719 #endif
 720
 721 /**
 722  * stmmac_tx_err:
 723  * @priv: pointer to the private device structure
 724  * Description: it cleans the descriptors and restarts the transmission
 725  * in case of errors.
 726  */
 727 static void stmmac_tx_err(struct stmmac_priv *priv)
 728 {
 729         netif_stop_queue(priv->dev);
 730
 731         priv->hw->dma->stop_tx(priv->ioaddr);
 732         dma_free_tx_skbufs(priv);
 733         priv->hw->desc->init_tx_desc(priv->dma_tx, priv->dma_tx_size);
 734         priv->dirty_tx = 0;
 735         priv->cur_tx = 0;
 736         priv->hw->dma->start_tx(priv->ioaddr);
 737
 738         priv->dev->stats.tx_errors++;
 739         netif_wake_queue(priv->dev);
 740 }
 741
 742
 743 static void stmmac_dma_interrupt(struct stmmac_priv *priv)
 744 {
 745         int status;
 746
 747         status = priv->hw->dma->dma_interrupt(priv->ioaddr, &priv->xstats);
 748         if (likely(status == handle_tx_rx))
 749                 _stmmac_schedule(priv);
 750
 751         else if (unlikely(status == tx_hard_error_bump_tc)) {
 752                 /* Try to bump up the dma threshold on this failure */
 753                 if (unlikely(tc != SF_DMA_MODE) && (tc <= 256)) {
 754                         tc += 64;
 755                         priv->hw->dma->dma_mode(priv->ioaddr, tc, SF_DMA_MODE);
 756                         priv->xstats.threshold = tc;
 757                 }
 758         } else if (unlikely(status == tx_hard_error))
 759                 stmmac_tx_err(priv);
 760 }
 761
 762 static void stmmac_mmc_setup(struct stmmac_priv *priv)
 763 {
 764         unsigned int mode = MMC_CNTRL_RESET_ON_READ | MMC_CNTRL_COUNTER_RESET |
 765                             MMC_CNTRL_PRESET | MMC_CNTRL_FULL_HALF_PRESET;
 766
 767         /* Mask MMC irq, counters are managed in SW and registers
 768          * are cleared on each READ eventually. */
 769         dwmac_mmc_intr_all_mask(priv->ioaddr);
 770
 771         if (priv->dma_cap.rmon) {
 772                 dwmac_mmc_ctrl(priv->ioaddr, mode);
 773                 memset(&priv->mmc, 0, sizeof(struct stmmac_counters));
 774         } else
 775                 pr_info(" No MAC Management Counters available\n");
 776 }
 777
 778 static u32 stmmac_get_synopsys_id(struct stmmac_priv *priv)
 779 {
 780         u32 hwid = priv->hw->synopsys_uid;
 781
 782         /* Only check valid Synopsys Id because old MAC chips
 783          * have no HW registers where get the ID */
 784         if (likely(hwid)) {
 785                 u32 uid = ((hwid & 0x0000ff00) >> 8);
 786                 u32 synid = (hwid & 0x000000ff);
 787
 788                 pr_info("stmmac - user ID: 0x%x, Synopsys ID: 0x%x\n",
 789                         uid, synid);
 790
 791                 return synid;
 792         }
 793         return 0;
 794 }
 795
 796 /**
 797  * stmmac_selec_desc_mode
 798  * @dev : device pointer
 799  * Description: select the Enhanced/Alternate or Normal descriptors */
 800 static void stmmac_selec_desc_mode(struct stmmac_priv *priv)
 801 {
 802         if (priv->plat->enh_desc) {
 803                 pr_info(" Enhanced/Alternate descriptors\n");
 804                 priv->hw->desc = &enh_desc_ops;
 805         } else {
 806                 pr_info(" Normal descriptors\n");
 807                 priv->hw->desc = &ndesc_ops;
 808         }
 809 }
 810
 811 /**
 812  * stmmac_get_hw_features
 813  * @priv : private device pointer
 814  * Description:
 815  *  new GMAC chip generations have a new register to indicate the
 816  *  presence of the optional feature/functions.
 817  *  This can be also used to override the value passed through the
 818  *  platform and necessary for old MAC10/100 and GMAC chips.
 819  */
 820 static int stmmac_get_hw_features(struct stmmac_priv *priv)
 821 {
 822         u32 hw_cap = 0;
 823
 824         if (priv->hw->dma->get_hw_feature) {
 825                 hw_cap = priv->hw->dma->get_hw_feature(priv->ioaddr);
 826
 827                 priv->dma_cap.mbps_10_100 = (hw_cap & DMA_HW_FEAT_MIISEL);
 828                 priv->dma_cap.mbps_1000 = (hw_cap & DMA_HW_FEAT_GMIISEL) >> 1;
 829                 priv->dma_cap.half_duplex = (hw_cap & DMA_HW_FEAT_HDSEL) >> 2;
 830                 priv->dma_cap.hash_filter = (hw_cap & DMA_HW_FEAT_HASHSEL) >> 4;
 831                 priv->dma_cap.multi_addr =
 832                         (hw_cap & DMA_HW_FEAT_ADDMACADRSEL) >> 5;
 833                 priv->dma_cap.pcs = (hw_cap & DMA_HW_FEAT_PCSSEL) >> 6;
 834                 priv->dma_cap.sma_mdio = (hw_cap & DMA_HW_FEAT_SMASEL) >> 8;
 835                 priv->dma_cap.pmt_remote_wake_up =
 836                         (hw_cap & DMA_HW_FEAT_RWKSEL) >> 9;
 837                 priv->dma_cap.pmt_magic_frame =
 838                         (hw_cap & DMA_HW_FEAT_MGKSEL) >> 10;
 839                 /* MMC */
 840                 priv->dma_cap.rmon = (hw_cap & DMA_HW_FEAT_MMCSEL) >> 11;
 841                 /* IEEE 1588-2002*/
 842                 priv->dma_cap.time_stamp =
 843                         (hw_cap & DMA_HW_FEAT_TSVER1SEL) >> 12;
 844                 /* IEEE 1588-2008*/
 845                 priv->dma_cap.atime_stamp =
 846                         (hw_cap & DMA_HW_FEAT_TSVER2SEL) >> 13;
 847                 /* 802.3az - Energy-Efficient Ethernet (EEE) */
 848                 priv->dma_cap.eee = (hw_cap & DMA_HW_FEAT_EEESEL) >> 14;
 849                 priv->dma_cap.av = (hw_cap & DMA_HW_FEAT_AVSEL) >> 15;
 850                 /* TX and RX csum */
 851                 priv->dma_cap.tx_coe = (hw_cap & DMA_HW_FEAT_TXCOESEL) >> 16;
 852                 priv->dma_cap.rx_coe_type1 =
 853                         (hw_cap & DMA_HW_FEAT_RXTYP1COE) >> 17;
 854                 priv->dma_cap.rx_coe_type2 =
 855                         (hw_cap & DMA_HW_FEAT_RXTYP2COE) >> 18;
 856                 priv->dma_cap.rxfifo_over_2048 =
 857                         (hw_cap & DMA_HW_FEAT_RXFIFOSIZE) >> 19;
 858                 /* TX and RX number of channels */
 859                 priv->dma_cap.number_rx_channel =
 860                         (hw_cap & DMA_HW_FEAT_RXCHCNT) >> 20;
 861                 priv->dma_cap.number_tx_channel =
 862                         (hw_cap & DMA_HW_FEAT_TXCHCNT) >> 22;
 863                 /* Alternate (enhanced) DESC mode*/
 864                 priv->dma_cap.enh_desc =
 865                         (hw_cap & DMA_HW_FEAT_ENHDESSEL) >> 24;
 866
 867         }
 868
 869         return hw_cap;
 870 }
 871
 872 static void stmmac_check_ether_addr(struct stmmac_priv *priv)
 873 {
 874         /* verify if the MAC address is valid, in case of failures it
 875          * generates a random MAC address */
 876         if (!is_valid_ether_addr(priv->dev->dev_addr)) {
 877                 priv->hw->mac->get_umac_addr((void __iomem *)
 878                                              priv->dev->base_addr,
 879                                              priv->dev->dev_addr, 0);
 880                 if  (!is_valid_ether_addr(priv->dev->dev_addr))
 881                         eth_hw_addr_random(priv->dev);
 882         }
 883         pr_warning("%s: device MAC address %pM\n", priv->dev->name,
 884                                                    priv->dev->dev_addr);
 885 }
 886
 887 /**
 888  *  stmmac_open - open entry point of the driver
 889  *  @dev : pointer to the device structure.
 890  *  Description:
 891  *  This function is the open entry point of the driver.
 892  *  Return value:
 893  *  0 on success and an appropriate (-)ve integer as defined in errno.h
 894  *  file on failure.
 895  */
 896 static int stmmac_open(struct net_device *dev)
 897 {
 898         struct stmmac_priv *priv = netdev_priv(dev);
 899         int ret;
 900
 901         stmmac_check_ether_addr(priv);
 902
 903         /* MDIO bus Registration */
 904         ret = stmmac_mdio_register(dev);
 905         if (ret < 0) {
 906                 pr_debug("%s: MDIO bus (id: %d) registration failed",
 907                          __func__, priv->plat->bus_id);
 908                 return ret;
 909         }
 910
 911 #ifdef CONFIG_STMMAC_TIMER
 912         priv->tm = kzalloc(sizeof(struct stmmac_timer *), GFP_KERNEL);
 913         if (unlikely(priv->tm == NULL))
 914                 return -ENOMEM;
 915
 916         priv->tm->freq = tmrate;
 917
 918         /* Test if the external timer can be actually used.
 919          * In case of failure continue without timer. */
 920         if (unlikely((stmmac_open_ext_timer(dev, priv->tm)) < 0)) {
 921                 pr_warning("stmmaceth: cannot attach the external timer.\n");
 922                 priv->tm->freq = 0;
 923                 priv->tm->timer_start = stmmac_no_timer_started;
 924                 priv->tm->timer_stop = stmmac_no_timer_stopped;
 925         } else
 926                 priv->tm->enable = 1;
 927 #endif
 928         ret = stmmac_init_phy(dev);
 929         if (unlikely(ret)) {
 930                 pr_err("%s: Cannot attach to PHY (error: %d)\n", __func__, ret);
 931                 goto open_error;
 932         }
 933
 934         /* Create and initialize the TX/RX descriptors chains. */
 935         priv->dma_tx_size = STMMAC_ALIGN(dma_txsize);
 936         priv->dma_rx_size = STMMAC_ALIGN(dma_rxsize);
 937         priv->dma_buf_sz = STMMAC_ALIGN(buf_sz);
 938         init_dma_desc_rings(dev);
 939
 940         /* DMA initialization and SW reset */
 941         ret = priv->hw->dma->init(priv->ioaddr, priv->plat->pbl,
 942                                   priv->dma_tx_phy, priv->dma_rx_phy);
 943         if (ret < 0) {
 944                 pr_err("%s: DMA initialization failed\n", __func__);
 945                 goto open_error;
 946         }
 947
 948         /* Copy the MAC addr into the HW  */
 949         priv->hw->mac->set_umac_addr(priv->ioaddr, dev->dev_addr, 0);
 950
 951         /* If required, perform hw setup of the bus. */
 952         if (priv->plat->bus_setup)
 953                 priv->plat->bus_setup(priv->ioaddr);
 954
 955         /* Initialize the MAC Core */
 956         priv->hw->mac->core_init(priv->ioaddr);
 957
 958         /* Request the IRQ lines */
 959         ret = request_irq(dev->irq, stmmac_interrupt,
 960                          IRQF_SHARED, dev->name, dev);
 961         if (unlikely(ret < 0)) {
 962                 pr_err("%s: ERROR: allocating the IRQ %d (error: %d)\n",
 963                        __func__, dev->irq, ret);
 964                 goto open_error;
 965         }
 966
 967         /* Request the Wake IRQ in case of another line is used for WoL */
 968         if (priv->wol_irq != dev->irq) {
 969                 ret = request_irq(priv->wol_irq, stmmac_interrupt,
 970                                   IRQF_SHARED, dev->name, dev);
 971                 if (unlikely(ret < 0)) {
 972                         pr_err("%s: ERROR: allocating the ext WoL IRQ %d "
 973                                "(error: %d)\n", __func__, priv->wol_irq, ret);
 974                         goto open_error_wolirq;
 975                 }
 976         }
 977
 978         /* Enable the MAC Rx/Tx */
 979         stmmac_set_mac(priv->ioaddr, true);
 980
 981         /* Set the HW DMA mode and the COE */
 982         stmmac_dma_operation_mode(priv);
 983
 984         /* Extra statistics */
 985         memset(&priv->xstats, 0, sizeof(struct stmmac_extra_stats));
 986         priv->xstats.threshold = tc;
 987
 988         stmmac_mmc_setup(priv);
 989
 990 #ifdef CONFIG_STMMAC_DEBUG_FS
 991         ret = stmmac_init_fs(dev);
 992         if (ret < 0)
 993                 pr_warning("%s: failed debugFS registration\n", __func__);
 994 #endif
 995         /* Start the ball rolling... */
 996         DBG(probe, DEBUG, "%s: DMA RX/TX processes started...\n", dev->name);
 997         priv->hw->dma->start_tx(priv->ioaddr);
 998         priv->hw->dma->start_rx(priv->ioaddr);
 999
1000 #ifdef CONFIG_STMMAC_TIMER
1001         priv->tm->timer_start(tmrate);
1002 #endif
1003
1004         /* Dump DMA/MAC registers */
1005         if (netif_msg_hw(priv)) {
1006                 priv->hw->mac->dump_regs(priv->ioaddr);
1007                 priv->hw->dma->dump_regs(priv->ioaddr);
1008         }
1009
1010         if (priv->phydev)
1011                 phy_start(priv->phydev);
1012
1013         napi_enable(&priv->napi);
1014         skb_queue_head_init(&priv->rx_recycle);
1015         netif_start_queue(dev);
1016
1017         return 0;
1018
1019 open_error_wolirq:
1020         free_irq(dev->irq, dev);
1021
1022 open_error:
1023 #ifdef CONFIG_STMMAC_TIMER
1024         kfree(priv->tm);
1025 #endif
1026         if (priv->phydev)
1027                 phy_disconnect(priv->phydev);
1028
1029         return ret;
1030 }
1031
1032 /**
1033  *  stmmac_release - close entry point of the driver
1034  *  @dev : device pointer.
1035  *  Description:
1036  *  This is the stop entry point of the driver.
1037  */
1038 static int stmmac_release(struct net_device *dev)
1039 {
1040         struct stmmac_priv *priv = netdev_priv(dev);
1041
1042         /* Stop and disconnect the PHY */
1043         if (priv->phydev) {
1044                 phy_stop(priv->phydev);
1045                 phy_disconnect(priv->phydev);
1046                 priv->phydev = NULL;
1047         }
1048
1049         netif_stop_queue(dev);
1050
1051 #ifdef CONFIG_STMMAC_TIMER
1052         /* Stop and release the timer */
1053         stmmac_close_ext_timer();
1054         if (priv->tm != NULL)
1055                 kfree(priv->tm);
1056 #endif
1057         napi_disable(&priv->napi);
1058         skb_queue_purge(&priv->rx_recycle);
1059
1060         /* Free the IRQ lines */
1061         free_irq(dev->irq, dev);
1062         if (priv->wol_irq != dev->irq)
1063                 free_irq(priv->wol_irq, dev);
1064
1065         /* Stop TX/RX DMA and clear the descriptors */
1066         priv->hw->dma->stop_tx(priv->ioaddr);
1067         priv->hw->dma->stop_rx(priv->ioaddr);
1068
1069         /* Release and free the Rx/Tx resources */
1070         free_dma_desc_resources(priv);
1071
1072         /* Disable the MAC Rx/Tx */
1073         stmmac_set_mac(priv->ioaddr, false);
1074
1075         netif_carrier_off(dev);
1076
1077 #ifdef CONFIG_STMMAC_DEBUG_FS
1078         stmmac_exit_fs();
1079 #endif
1080         stmmac_mdio_unregister(dev);
1081
1082         return 0;
1083 }
1084
1085 /**
1086  *  stmmac_xmit:
1087  *  @skb : the socket buffer
1088  *  @dev : device pointer
1089  *  Description : Tx entry point of the driver.
1090  */
1091 static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev)
1092 {
1093         struct stmmac_priv *priv = netdev_priv(dev);
1094         unsigned int txsize = priv->dma_tx_size;
1095         unsigned int entry;
1096         int i, csum_insertion = 0;
1097         int nfrags = skb_shinfo(skb)->nr_frags;
1098         struct dma_desc *desc, *first;
1099         unsigned int nopaged_len = skb_headlen(skb);
1100
1101         if (unlikely(stmmac_tx_avail(priv) < nfrags + 1)) {
1102                 if (!netif_queue_stopped(dev)) {
1103                         netif_stop_queue(dev);
1104                         /* This is a hard error, log it. */
1105                         pr_err("%s: BUG! Tx Ring full when queue awake\n",
1106                                 __func__);
1107                 }
1108                 return NETDEV_TX_BUSY;
1109         }
1110
1111         spin_lock(&priv->tx_lock);
1112
1113         entry = priv->cur_tx % txsize;
1114
1115 #ifdef STMMAC_XMIT_DEBUG
1116         if ((skb->len > ETH_FRAME_LEN) || nfrags)
1117                 pr_info("stmmac xmit:\n"
1118                        "\tskb addr %p - len: %d - nopaged_len: %d\n"
1119                        "\tn_frags: %d - ip_summed: %d - %s gso\n",
1120                        skb, skb->len, nopaged_len, nfrags, skb->ip_summed,
1121                        !skb_is_gso(skb) ? "isn't" : "is");
1122 #endif
1123
1124         csum_insertion = (skb->ip_summed == CHECKSUM_PARTIAL);
1125
1126         desc = priv->dma_tx + entry;
1127         first = desc;
1128
1129 #ifdef STMMAC_XMIT_DEBUG
1130         if ((nfrags > 0) || (skb->len > ETH_FRAME_LEN))
1131                 pr_debug("stmmac xmit: skb len: %d, nopaged_len: %d,\n"
1132                        "\t\tn_frags: %d, ip_summed: %d\n",
1133                        skb->len, nopaged_len, nfrags, skb->ip_summed);
1134 #endif
1135         priv->tx_skbuff[entry] = skb;
1136
1137         if (priv->hw->ring->is_jumbo_frm(skb->len, priv->plat->enh_desc)) {
1138                 entry = priv->hw->ring->jumbo_frm(priv, skb, csum_insertion);
1139                 desc = priv->dma_tx + entry;
1140         } else {
1141                 desc->des2 = dma_map_single(priv->device, skb->data,
1142                                         nopaged_len, DMA_TO_DEVICE);
1143                 priv->hw->desc->prepare_tx_desc(desc, 1, nopaged_len,
1144                                                 csum_insertion);
1145         }
1146
1147         for (i = 0; i < nfrags; i++) {
1148                 const skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
1149                 int len = skb_frag_size(frag);
1150
1151                 entry = (++priv->cur_tx) % txsize;
1152                 desc = priv->dma_tx + entry;
1153
1154                 TX_DBG("\t[entry %d] segment len: %d\n", entry, len);
1155                 desc->des2 = skb_frag_dma_map(priv->device, frag, 0, len,
1156                                               DMA_TO_DEVICE);
1157                 priv->tx_skbuff[entry] = NULL;
1158                 priv->hw->desc->prepare_tx_desc(desc, 0, len, csum_insertion);
1159                 wmb();
1160                 priv->hw->desc->set_tx_owner(desc);
1161                 wmb();
1162         }
1163
1164         /* Interrupt on completition only for the latest segment */
1165         priv->hw->desc->close_tx_desc(desc);
1166
1167 #ifdef CONFIG_STMMAC_TIMER
1168         /* Clean IC while using timer */
1169         if (likely(priv->tm->enable))
1170                 priv->hw->desc->clear_tx_ic(desc);
1171 #endif
1172
1173         wmb();
1174
1175         /* To avoid raise condition */
1176         priv->hw->desc->set_tx_owner(first);
1177         wmb();
1178
1179         priv->cur_tx++;
1180
1181 #ifdef STMMAC_XMIT_DEBUG
1182         if (netif_msg_pktdata(priv)) {
1183                 pr_info("stmmac xmit: current=%d, dirty=%d, entry=%d, "
1184                        "first=%p, nfrags=%d\n",
1185                        (priv->cur_tx % txsize), (priv->dirty_tx % txsize),
1186                        entry, first, nfrags);
1187                 display_ring(priv->dma_tx, txsize);
1188                 pr_info(">>> frame to be transmitted: ");
1189                 print_pkt(skb->data, skb->len);
1190         }
1191 #endif
1192         if (unlikely(stmmac_tx_avail(priv) <= (MAX_SKB_FRAGS + 1))) {
1193                 TX_DBG("%s: stop transmitted packets\n", __func__);
1194                 netif_stop_queue(dev);
1195         }
1196
1197         dev->stats.tx_bytes += skb->len;
1198
1199         skb_tx_timestamp(skb);
1200
1201         priv->hw->dma->enable_dma_transmission(priv->ioaddr);
1202
1203         spin_unlock(&priv->tx_lock);
1204
1205         return NETDEV_TX_OK;
1206 }
1207
1208 static inline void stmmac_rx_refill(struct stmmac_priv *priv)
1209 {
1210         unsigned int rxsize = priv->dma_rx_size;
1211         int bfsize = priv->dma_buf_sz;
1212         struct dma_desc *p = priv->dma_rx;
1213
1214         for (; priv->cur_rx - priv->dirty_rx > 0; priv->dirty_rx++) {
1215                 unsigned int entry = priv->dirty_rx % rxsize;
1216                 if (likely(priv->rx_skbuff[entry] == NULL)) {
1217                         struct sk_buff *skb;
1218
1219                         skb = __skb_dequeue(&priv->rx_recycle);
1220                         if (skb == NULL)
1221                                 skb = netdev_alloc_skb_ip_align(priv->dev,
1222                                                                 bfsize);
1223
1224                         if (unlikely(skb == NULL))
1225                                 break;
1226
1227                         priv->rx_skbuff[entry] = skb;
1228                         priv->rx_skbuff_dma[entry] =
1229                             dma_map_single(priv->device, skb->data, bfsize,
1230                                            DMA_FROM_DEVICE);
1231
1232                         (p + entry)->des2 = priv->rx_skbuff_dma[entry];
1233
1234                         if (unlikely(priv->plat->has_gmac))
1235                                 priv->hw->ring->refill_desc3(bfsize, p + entry);
1236
1237                         RX_DBG(KERN_INFO "\trefill entry #%d\n", entry);
1238                 }
1239                 wmb();
1240                 priv->hw->desc->set_rx_owner(p + entry);
1241                 wmb();
1242         }
1243 }
1244
1245 static int stmmac_rx(struct stmmac_priv *priv, int limit)
1246 {
1247         unsigned int rxsize = priv->dma_rx_size;
1248         unsigned int entry = priv->cur_rx % rxsize;
1249         unsigned int next_entry;
1250         unsigned int count = 0;
1251         struct dma_desc *p = priv->dma_rx + entry;
1252         struct dma_desc *p_next;
1253
1254 #ifdef STMMAC_RX_DEBUG
1255         if (netif_msg_hw(priv)) {
1256                 pr_debug(">>> stmmac_rx: descriptor ring:\n");
1257                 display_ring(priv->dma_rx, rxsize);
1258         }
1259 #endif
1260         count = 0;
1261         while (!priv->hw->desc->get_rx_owner(p)) {
1262                 int status;
1263
1264                 if (count >= limit)
1265                         break;
1266
1267                 count++;
1268
1269                 next_entry = (++priv->cur_rx) % rxsize;
1270                 p_next = priv->dma_rx + next_entry;
1271                 prefetch(p_next);
1272
1273                 /* read the status of the incoming frame */
1274                 status = (priv->hw->desc->rx_status(&priv->dev->stats,
1275                                                     &priv->xstats, p));
1276                 if (unlikely(status == discard_frame))
1277                         priv->dev->stats.rx_errors++;
1278                 else {
1279                         struct sk_buff *skb;
1280                         int frame_len;
1281
1282                         frame_len = priv->hw->desc->get_rx_frame_len(p);
1283                         /* ACS is set; GMAC core strips PAD/FCS for IEEE 802.3
1284                          * Type frames (LLC/LLC-SNAP) */
1285                         if (unlikely(status != llc_snap))
1286                                 frame_len -= ETH_FCS_LEN;
1287 #ifdef STMMAC_RX_DEBUG
1288                         if (frame_len > ETH_FRAME_LEN)
1289                                 pr_debug("\tRX frame size %d, COE status: %d\n",
1290                                         frame_len, status);
1291
1292                         if (netif_msg_hw(priv))
1293                                 pr_debug("\tdesc: %p [entry %d] buff=0x%x\n",
1294                                         p, entry, p->des2);
1295 #endif
1296                         skb = priv->rx_skbuff[entry];
1297                         if (unlikely(!skb)) {
1298                                 pr_err("%s: Inconsistent Rx descriptor chain\n",
1299                                         priv->dev->name);
1300                                 priv->dev->stats.rx_dropped++;
1301                                 break;
1302                         }
1303                         prefetch(skb->data - NET_IP_ALIGN);
1304                         priv->rx_skbuff[entry] = NULL;
1305
1306                         skb_put(skb, frame_len);
1307                         dma_unmap_single(priv->device,
1308                                          priv->rx_skbuff_dma[entry],
1309                                          priv->dma_buf_sz, DMA_FROM_DEVICE);
1310 #ifdef STMMAC_RX_DEBUG
1311                         if (netif_msg_pktdata(priv)) {
1312                                 pr_info(" frame received (%dbytes)", frame_len);
1313                                 print_pkt(skb->data, frame_len);
1314                         }
1315 #endif
1316                         skb->protocol = eth_type_trans(skb, priv->dev);
1317
1318                         if (unlikely(!priv->rx_coe)) {
1319                                 /* No RX COE for old mac10/100 devices */
1320                                 skb_checksum_none_assert(skb);
1321                                 netif_receive_skb(skb);
1322                         } else {
1323                                 skb->ip_summed = CHECKSUM_UNNECESSARY;
1324                                 napi_gro_receive(&priv->napi, skb);
1325                         }
1326
1327                         priv->dev->stats.rx_packets++;
1328                         priv->dev->stats.rx_bytes += frame_len;
1329                 }
1330                 entry = next_entry;
1331                 p = p_next;     /* use prefetched values */
1332         }
1333
1334         stmmac_rx_refill(priv);
1335
1336         priv->xstats.rx_pkt_n += count;
1337
1338         return count;
1339 }
1340
1341 /**
1342  *  stmmac_poll - stmmac poll method (NAPI)
1343  *  @napi : pointer to the napi structure.
1344  *  @budget : maximum number of packets that the current CPU can receive from
1345  *            all interfaces.
1346  *  Description :
1347  *   This function implements the the reception process.
1348  *   Also it runs the TX completion thread
1349  */
1350 static int stmmac_poll(struct napi_struct *napi, int budget)
1351 {
1352         struct stmmac_priv *priv = container_of(napi, struct stmmac_priv, napi);
1353         int work_done = 0;
1354
1355         priv->xstats.poll_n++;
1356         stmmac_tx(priv);
1357         work_done = stmmac_rx(priv, budget);
1358
1359         if (work_done < budget) {
1360                 napi_complete(napi);
1361                 stmmac_enable_irq(priv);
1362         }
1363         return work_done;
1364 }
1365
1366 /**
1367  *  stmmac_tx_timeout
1368  *  @dev : Pointer to net device structure
1369  *  Description: this function is called when a packet transmission fails to
1370  *   complete within a reasonable tmrate. The driver will mark the error in the
1371  *   netdev structure and arrange for the device to be reset to a sane state
1372  *   in order to transmit a new packet.
1373  */
1374 static void stmmac_tx_timeout(struct net_device *dev)
1375 {
1376         struct stmmac_priv *priv = netdev_priv(dev);
1377
1378         /* Clear Tx resources and restart transmitting again */
1379         stmmac_tx_err(priv);
1380 }
1381
1382 /* Configuration changes (passed on by ifconfig) */
1383 static int stmmac_config(struct net_device *dev, struct ifmap *map)
1384 {
1385         if (dev->flags & IFF_UP)        /* can't act on a running interface */
1386                 return -EBUSY;
1387
1388         /* Don't allow changing the I/O address */
1389         if (map->base_addr != dev->base_addr) {
1390                 pr_warning("%s: can't change I/O address\n", dev->name);
1391                 return -EOPNOTSUPP;
1392         }
1393
1394         /* Don't allow changing the IRQ */
1395         if (map->irq != dev->irq) {
1396                 pr_warning("%s: can't change IRQ number %d\n",
1397                        dev->name, dev->irq);
1398                 return -EOPNOTSUPP;
1399         }
1400
1401         /* ignore other fields */
1402         return 0;
1403 }
1404
1405 /**
1406  *  stmmac_set_rx_mode - entry point for multicast addressing
1407  *  @dev : pointer to the device structure
1408  *  Description:
1409  *  This function is a driver entry point which gets called by the kernel
1410  *  whenever multicast addresses must be enabled/disabled.
1411  *  Return value:
1412  *  void.
1413  */
1414 static void stmmac_set_rx_mode(struct net_device *dev)
1415 {
1416         struct stmmac_priv *priv = netdev_priv(dev);
1417
1418         spin_lock(&priv->lock);
1419         priv->hw->mac->set_filter(dev);
1420         spin_unlock(&priv->lock);
1421 }
1422
1423 /**
1424  *  stmmac_change_mtu - entry point to change MTU size for the device.
1425  *  @dev : device pointer.
1426  *  @new_mtu : the new MTU size for the device.
1427  *  Description: the Maximum Transfer Unit (MTU) is used by the network layer
1428  *  to drive packet transmission. Ethernet has an MTU of 1500 octets
1429  *  (ETH_DATA_LEN). This value can be changed with ifconfig.
1430  *  Return value:
1431  *  0 on success and an appropriate (-)ve integer as defined in errno.h
1432  *  file on failure.
1433  */
1434 static int stmmac_change_mtu(struct net_device *dev, int new_mtu)
1435 {
1436         struct stmmac_priv *priv = netdev_priv(dev);
1437         int max_mtu;
1438
1439         if (netif_running(dev)) {
1440                 pr_err("%s: must be stopped to change its MTU\n", dev->name);
1441                 return -EBUSY;
1442         }
1443
1444         if (priv->plat->enh_desc)
1445                 max_mtu = JUMBO_LEN;
1446         else
1447                 max_mtu = SKB_MAX_HEAD(NET_SKB_PAD + NET_IP_ALIGN);
1448
1449         if ((new_mtu < 46) || (new_mtu > max_mtu)) {
1450                 pr_err("%s: invalid MTU, max MTU is: %d\n", dev->name, max_mtu);
1451                 return -EINVAL;
1452         }
1453
1454         dev->mtu = new_mtu;
1455         netdev_update_features(dev);
1456
1457         return 0;
1458 }
1459
1460 static netdev_features_t stmmac_fix_features(struct net_device *dev,
1461         netdev_features_t features)
1462 {
1463         struct stmmac_priv *priv = netdev_priv(dev);
1464
1465         if (!priv->rx_coe)
1466                 features &= ~NETIF_F_RXCSUM;
1467         if (!priv->plat->tx_coe)
1468                 features &= ~NETIF_F_ALL_CSUM;
1469
1470         /* Some GMAC devices have a bugged Jumbo frame support that
1471          * needs to have the Tx COE disabled for oversized frames
1472          * (due to limited buffer sizes). In this case we disable
1473          * the TX csum insertionin the TDES and not use SF. */
1474         if (priv->plat->bugged_jumbo && (dev->mtu > ETH_DATA_LEN))
1475                 features &= ~NETIF_F_ALL_CSUM;
1476
1477         return features;
1478 }
1479
1480 static irqreturn_t stmmac_interrupt(int irq, void *dev_id)
1481 {
1482         struct net_device *dev = (struct net_device *)dev_id;
1483         struct stmmac_priv *priv = netdev_priv(dev);
1484
1485         if (unlikely(!dev)) {
1486                 pr_err("%s: invalid dev pointer\n", __func__);
1487                 return IRQ_NONE;
1488         }
1489
1490         if (priv->plat->has_gmac)
1491                 /* To handle GMAC own interrupts */
1492                 priv->hw->mac->host_irq_status((void __iomem *) dev->base_addr);
1493
1494         stmmac_dma_interrupt(priv);
1495
1496         return IRQ_HANDLED;
1497 }
1498
1499 #ifdef CONFIG_NET_POLL_CONTROLLER
1500 /* Polling receive - used by NETCONSOLE and other diagnostic tools
1501  * to allow network I/O with interrupts disabled. */
1502 static void stmmac_poll_controller(struct net_device *dev)
1503 {
1504         disable_irq(dev->irq);
1505         stmmac_interrupt(dev->irq, dev);
1506         enable_irq(dev->irq);
1507 }
1508 #endif
1509
1510 /**
1511  *  stmmac_ioctl - Entry point for the Ioctl
1512  *  @dev: Device pointer.
1513  *  @rq: An IOCTL specefic structure, that can contain a pointer to
1514  *  a proprietary structure used to pass information to the driver.
1515  *  @cmd: IOCTL command
1516  *  Description:
1517  *  Currently there are no special functionality supported in IOCTL, just the
1518  *  phy_mii_ioctl(...) can be invoked.
1519  */
1520 static int stmmac_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
1521 {
1522         struct stmmac_priv *priv = netdev_priv(dev);
1523         int ret;
1524
1525         if (!netif_running(dev))
1526                 return -EINVAL;
1527
1528         if (!priv->phydev)
1529                 return -EINVAL;
1530
1531         ret = phy_mii_ioctl(priv->phydev, rq, cmd);
1532
1533         return ret;
1534 }
1535
1536 #ifdef CONFIG_STMMAC_DEBUG_FS
1537 static struct dentry *stmmac_fs_dir;
1538 static struct dentry *stmmac_rings_status;
1539 static struct dentry *stmmac_dma_cap;
1540
1541 static int stmmac_sysfs_ring_read(struct seq_file *seq, void *v)
1542 {
1543         struct tmp_s {
1544                 u64 a;
1545                 unsigned int b;
1546                 unsigned int c;
1547         };
1548         int i;
1549         struct net_device *dev = seq->private;
1550         struct stmmac_priv *priv = netdev_priv(dev);
1551
1552         seq_printf(seq, "=======================\n");
1553         seq_printf(seq, " RX descriptor ring\n");
1554         seq_printf(seq, "=======================\n");
1555
1556         for (i = 0; i < priv->dma_rx_size; i++) {
1557                 struct tmp_s *x = (struct tmp_s *)(priv->dma_rx + i);
1558                 seq_printf(seq, "[%d] DES0=0x%x DES1=0x%x BUF1=0x%x BUF2=0x%x",
1559                            i, (unsigned int)(x->a),
1560                            (unsigned int)((x->a) >> 32), x->b, x->c);
1561                 seq_printf(seq, "\n");
1562         }
1563
1564         seq_printf(seq, "\n");
1565         seq_printf(seq, "=======================\n");
1566         seq_printf(seq, "  TX descriptor ring\n");
1567         seq_printf(seq, "=======================\n");
1568
1569         for (i = 0; i < priv->dma_tx_size; i++) {
1570                 struct tmp_s *x = (struct tmp_s *)(priv->dma_tx + i);
1571                 seq_printf(seq, "[%d] DES0=0x%x DES1=0x%x BUF1=0x%x BUF2=0x%x",
1572                            i, (unsigned int)(x->a),
1573                            (unsigned int)((x->a) >> 32), x->b, x->c);
1574                 seq_printf(seq, "\n");
1575         }
1576
1577         return 0;
1578 }
1579
1580 static int stmmac_sysfs_ring_open(struct inode *inode, struct file *file)
1581 {
1582         return single_open(file, stmmac_sysfs_ring_read, inode->i_private);
1583 }
1584
1585 static const struct file_operations stmmac_rings_status_fops = {
1586         .owner = THIS_MODULE,
1587         .open = stmmac_sysfs_ring_open,
1588         .read = seq_read,
1589         .llseek = seq_lseek,
1590         .release = seq_release,
1591 };
1592
1593 static int stmmac_sysfs_dma_cap_read(struct seq_file *seq, void *v)
1594 {
1595         struct net_device *dev = seq->private;
1596         struct stmmac_priv *priv = netdev_priv(dev);
1597
1598         if (!priv->hw_cap_support) {
1599                 seq_printf(seq, "DMA HW features not supported\n");
1600                 return 0;
1601         }
1602
1603         seq_printf(seq, "==============================\n");
1604         seq_printf(seq, "\tDMA HW features\n");
1605         seq_printf(seq, "==============================\n");
1606
1607         seq_printf(seq, "\t10/100 Mbps %s\n",
1608                    (priv->dma_cap.mbps_10_100) ? "Y" : "N");
1609         seq_printf(seq, "\t1000 Mbps %s\n",
1610                    (priv->dma_cap.mbps_1000) ? "Y" : "N");
1611         seq_printf(seq, "\tHalf duple %s\n",
1612                    (priv->dma_cap.half_duplex) ? "Y" : "N");
1613         seq_printf(seq, "\tHash Filter: %s\n",
1614                    (priv->dma_cap.hash_filter) ? "Y" : "N");
1615         seq_printf(seq, "\tMultiple MAC address registers: %s\n",
1616                    (priv->dma_cap.multi_addr) ? "Y" : "N");
1617         seq_printf(seq, "\tPCS (TBI/SGMII/RTBI PHY interfatces): %s\n",
1618                    (priv->dma_cap.pcs) ? "Y" : "N");
1619         seq_printf(seq, "\tSMA (MDIO) Interface: %s\n",
1620                    (priv->dma_cap.sma_mdio) ? "Y" : "N");
1621         seq_printf(seq, "\tPMT Remote wake up: %s\n",
1622                    (priv->dma_cap.pmt_remote_wake_up) ? "Y" : "N");
1623         seq_printf(seq, "\tPMT Magic Frame: %s\n",
1624                    (priv->dma_cap.pmt_magic_frame) ? "Y" : "N");
1625         seq_printf(seq, "\tRMON module: %s\n",
1626                    (priv->dma_cap.rmon) ? "Y" : "N");
1627         seq_printf(seq, "\tIEEE 1588-2002 Time Stamp: %s\n",
1628                    (priv->dma_cap.time_stamp) ? "Y" : "N");
1629         seq_printf(seq, "\tIEEE 1588-2008 Advanced Time Stamp:%s\n",
1630                    (priv->dma_cap.atime_stamp) ? "Y" : "N");
1631         seq_printf(seq, "\t802.3az - Energy-Efficient Ethernet (EEE) %s\n",
1632                    (priv->dma_cap.eee) ? "Y" : "N");
1633         seq_printf(seq, "\tAV features: %s\n", (priv->dma_cap.av) ? "Y" : "N");
1634         seq_printf(seq, "\tChecksum Offload in TX: %s\n",
1635                    (priv->dma_cap.tx_coe) ? "Y" : "N");
1636         seq_printf(seq, "\tIP Checksum Offload (type1) in RX: %s\n",
1637                    (priv->dma_cap.rx_coe_type1) ? "Y" : "N");
1638         seq_printf(seq, "\tIP Checksum Offload (type2) in RX: %s\n",
1639                    (priv->dma_cap.rx_coe_type2) ? "Y" : "N");
1640         seq_printf(seq, "\tRXFIFO > 2048bytes: %s\n",
1641                    (priv->dma_cap.rxfifo_over_2048) ? "Y" : "N");
1642         seq_printf(seq, "\tNumber of Additional RX channel: %d\n",
1643                    priv->dma_cap.number_rx_channel);
1644         seq_printf(seq, "\tNumber of Additional TX channel: %d\n",
1645                    priv->dma_cap.number_tx_channel);
1646         seq_printf(seq, "\tEnhanced descriptors: %s\n",
1647                    (priv->dma_cap.enh_desc) ? "Y" : "N");
1648
1649         return 0;
1650 }
1651
1652 static int stmmac_sysfs_dma_cap_open(struct inode *inode, struct file *file)
1653 {
1654         return single_open(file, stmmac_sysfs_dma_cap_read, inode->i_private);
1655 }
1656
1657 static const struct file_operations stmmac_dma_cap_fops = {
1658         .owner = THIS_MODULE,
1659         .open = stmmac_sysfs_dma_cap_open,
1660         .read = seq_read,
1661         .llseek = seq_lseek,
1662         .release = seq_release,
1663 };
1664
1665 static int stmmac_init_fs(struct net_device *dev)
1666 {
1667         /* Create debugfs entries */
1668         stmmac_fs_dir = debugfs_create_dir(STMMAC_RESOURCE_NAME, NULL);
1669
1670         if (!stmmac_fs_dir || IS_ERR(stmmac_fs_dir)) {
1671                 pr_err("ERROR %s, debugfs create directory failed\n",
1672                        STMMAC_RESOURCE_NAME);
1673
1674                 return -ENOMEM;
1675         }
1676
1677         /* Entry to report DMA RX/TX rings */
1678         stmmac_rings_status = debugfs_create_file("descriptors_status",
1679                                            S_IRUGO, stmmac_fs_dir, dev,
1680                                            &stmmac_rings_status_fops);
1681
1682         if (!stmmac_rings_status || IS_ERR(stmmac_rings_status)) {
1683                 pr_info("ERROR creating stmmac ring debugfs file\n");
1684                 debugfs_remove(stmmac_fs_dir);
1685
1686                 return -ENOMEM;
1687         }
1688
1689         /* Entry to report the DMA HW features */
1690         stmmac_dma_cap = debugfs_create_file("dma_cap", S_IRUGO, stmmac_fs_dir,
1691                                              dev, &stmmac_dma_cap_fops);
1692
1693         if (!stmmac_dma_cap || IS_ERR(stmmac_dma_cap)) {
1694                 pr_info("ERROR creating stmmac MMC debugfs file\n");
1695                 debugfs_remove(stmmac_rings_status);
1696                 debugfs_remove(stmmac_fs_dir);
1697
1698                 return -ENOMEM;
1699         }
1700
1701         return 0;
1702 }
1703
1704 static void stmmac_exit_fs(void)
1705 {
1706         debugfs_remove(stmmac_rings_status);
1707         debugfs_remove(stmmac_dma_cap);
1708         debugfs_remove(stmmac_fs_dir);
1709 }
1710 #endif /* CONFIG_STMMAC_DEBUG_FS */
1711
1712 static const struct net_device_ops stmmac_netdev_ops = {
1713         .ndo_open = stmmac_open,
1714         .ndo_start_xmit = stmmac_xmit,
1715         .ndo_stop = stmmac_release,
1716         .ndo_change_mtu = stmmac_change_mtu,
1717         .ndo_fix_features = stmmac_fix_features,
1718         .ndo_set_rx_mode = stmmac_set_rx_mode,
1719         .ndo_tx_timeout = stmmac_tx_timeout,
1720         .ndo_do_ioctl = stmmac_ioctl,
1721         .ndo_set_config = stmmac_config,
1722 #ifdef CONFIG_NET_POLL_CONTROLLER
1723         .ndo_poll_controller = stmmac_poll_controller,
1724 #endif
1725         .ndo_set_mac_address = eth_mac_addr,
1726 };
1727
1728 /**
1729  *  stmmac_hw_init - Init the MAC device
1730  *  @priv : pointer to the private device structure.
1731  *  Description: this function detects which MAC device
1732  *  (GMAC/MAC10-100) has to attached, checks the HW capability
1733  *  (if supported) and sets the driver's features (for example
1734  *  to use the ring or chaine mode or support the normal/enh
1735  *  descriptor structure).
1736  */
1737 static int stmmac_hw_init(struct stmmac_priv *priv)
1738 {
1739         int ret = 0;
1740         struct mac_device_info *mac;
1741
1742         /* Identify the MAC HW device */
1743         if (priv->plat->has_gmac) {
1744                 priv->dev->priv_flags |= IFF_UNICAST_FLT;
1745                 mac = dwmac1000_setup(priv->ioaddr);
1746         } else {
1747                 mac = dwmac100_setup(priv->ioaddr);
1748         }
1749         if (!mac)
1750                 return -ENOMEM;
1751
1752         priv->hw = mac;
1753
1754         /* To use the chained or ring mode */
1755         priv->hw->ring = &ring_mode_ops;
1756
1757         /* Get and dump the chip ID */
1758         stmmac_get_synopsys_id(priv);
1759
1760         /* Get the HW capability (new GMAC newer than 3.50a) */
1761         priv->hw_cap_support = stmmac_get_hw_features(priv);
1762         if (priv->hw_cap_support) {
1763                 pr_info(" DMA HW capability register supported");
1764
1765                 /* We can override some gmac/dma configuration fields: e.g.
1766                  * enh_desc, tx_coe (e.g. that are passed through the
1767                  * platform) with the values from the HW capability
1768                  * register (if supported).
1769                  */
1770                 priv->plat->enh_desc = priv->dma_cap.enh_desc;
1771                 priv->plat->tx_coe = priv->dma_cap.tx_coe;
1772                 priv->plat->pmt = priv->dma_cap.pmt_remote_wake_up;
1773         } else
1774                 pr_info(" No HW DMA feature register supported");
1775
1776         /* Select the enhnaced/normal descriptor structures */
1777         stmmac_selec_desc_mode(priv);
1778
1779         priv->rx_coe = priv->hw->mac->rx_coe(priv->ioaddr);
1780         if (priv->rx_coe)
1781                 pr_info(" RX Checksum Offload Engine supported\n");
1782         if (priv->plat->tx_coe)
1783                 pr_info(" TX Checksum insertion supported\n");
1784
1785         if (priv->plat->pmt) {
1786                 pr_info(" Wake-Up On Lan supported\n");
1787                 device_set_wakeup_capable(priv->device, 1);
1788         }
1789
1790         return ret;
1791 }
1792
1793 /**
1794  * stmmac_dvr_probe
1795  * @device: device pointer
1796  * Description: this is the main probe function used to
1797  * call the alloc_etherdev, allocate the priv structure.
1798  */
1799 struct stmmac_priv *stmmac_dvr_probe(struct device *device,
1800                                      struct plat_stmmacenet_data *plat_dat,
1801                                      void __iomem *addr)
1802 {
1803         int ret = 0;
1804         struct net_device *ndev = NULL;
1805         struct stmmac_priv *priv;
1806
1807         ndev = alloc_etherdev(sizeof(struct stmmac_priv));
1808         if (!ndev)
1809                 return NULL;
1810
1811         SET_NETDEV_DEV(ndev, device);
1812
1813         priv = netdev_priv(ndev);
1814         priv->device = device;
1815         priv->dev = ndev;
1816
1817         ether_setup(ndev);
1818
1819         stmmac_set_ethtool_ops(ndev);
1820         priv->pause = pause;
1821         priv->plat = plat_dat;
1822         priv->ioaddr = addr;
1823         priv->dev->base_addr = (unsigned long)addr;
1824
1825         /* Verify driver arguments */
1826         stmmac_verify_args();
1827
1828         /* Override with kernel parameters if supplied XXX CRS XXX
1829          * this needs to have multiple instances */
1830         if ((phyaddr >= 0) && (phyaddr <= 31))
1831                 priv->plat->phy_addr = phyaddr;
1832
1833         /* Init MAC and get the capabilities */
1834         stmmac_hw_init(priv);
1835
1836         ndev->netdev_ops = &stmmac_netdev_ops;
1837
1838         ndev->hw_features = NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM |
1839                             NETIF_F_RXCSUM;
1840         ndev->features |= ndev->hw_features | NETIF_F_HIGHDMA;
1841         ndev->watchdog_timeo = msecs_to_jiffies(watchdog);
1842 #ifdef STMMAC_VLAN_TAG_USED
1843         /* Both mac100 and gmac support receive VLAN tag detection */
1844         ndev->features |= NETIF_F_HW_VLAN_RX;
1845 #endif
1846         priv->msg_enable = netif_msg_init(debug, default_msg_level);
1847
1848         if (flow_ctrl)
1849                 priv->flow_ctrl = FLOW_AUTO;    /* RX/TX pause on */
1850
1851         netif_napi_add(ndev, &priv->napi, stmmac_poll, 64);
1852
1853         spin_lock_init(&priv->lock);
1854         spin_lock_init(&priv->tx_lock);
1855
1856         ret = register_netdev(ndev);
1857         if (ret) {
1858                 pr_err("%s: ERROR %i registering the device\n", __func__, ret);
1859                 goto error;
1860         }
1861
1862         return priv;
1863
1864 error:
1865         netif_napi_del(&priv->napi);
1866
1867         unregister_netdev(ndev);
1868         free_netdev(ndev);
1869
1870         return NULL;
1871 }
1872
1873 /**
1874  * stmmac_dvr_remove
1875  * @ndev: net device pointer
1876  * Description: this function resets the TX/RX processes, disables the MAC RX/TX
1877  * changes the link status, releases the DMA descriptor rings.
1878  */
1879 int stmmac_dvr_remove(struct net_device *ndev)
1880 {
1881         struct stmmac_priv *priv = netdev_priv(ndev);
1882
1883         pr_info("%s:\n\tremoving driver", __func__);
1884
1885         priv->hw->dma->stop_rx(priv->ioaddr);
1886         priv->hw->dma->stop_tx(priv->ioaddr);
1887
1888         stmmac_set_mac(priv->ioaddr, false);
1889         netif_carrier_off(ndev);
1890         unregister_netdev(ndev);
1891         free_netdev(ndev);
1892
1893         return 0;
1894 }
1895
1896 #ifdef CONFIG_PM
1897 int stmmac_suspend(struct net_device *ndev)
1898 {
1899         struct stmmac_priv *priv = netdev_priv(ndev);
1900         int dis_ic = 0;
1901
1902         if (!ndev || !netif_running(ndev))
1903                 return 0;
1904
1905         if (priv->phydev)
1906                 phy_stop(priv->phydev);
1907
1908         spin_lock(&priv->lock);
1909
1910         netif_device_detach(ndev);
1911         netif_stop_queue(ndev);
1912
1913 #ifdef CONFIG_STMMAC_TIMER
1914         priv->tm->timer_stop();
1915         if (likely(priv->tm->enable))
1916                 dis_ic = 1;
1917 #endif
1918         napi_disable(&priv->napi);
1919
1920         /* Stop TX/RX DMA */
1921         priv->hw->dma->stop_tx(priv->ioaddr);
1922         priv->hw->dma->stop_rx(priv->ioaddr);
1923         /* Clear the Rx/Tx descriptors */
1924         priv->hw->desc->init_rx_desc(priv->dma_rx, priv->dma_rx_size,
1925                                      dis_ic);
1926         priv->hw->desc->init_tx_desc(priv->dma_tx, priv->dma_tx_size);
1927
1928         /* Enable Power down mode by programming the PMT regs */
1929         if (device_may_wakeup(priv->device))
1930                 priv->hw->mac->pmt(priv->ioaddr, priv->wolopts);
1931         else
1932                 stmmac_set_mac(priv->ioaddr, false);
1933
1934         spin_unlock(&priv->lock);
1935         return 0;
1936 }
1937
1938 int stmmac_resume(struct net_device *ndev)
1939 {
1940         struct stmmac_priv *priv = netdev_priv(ndev);
1941
1942         if (!netif_running(ndev))
1943                 return 0;
1944
1945         spin_lock(&priv->lock);
1946
1947         /* Power Down bit, into the PM register, is cleared
1948          * automatically as soon as a magic packet or a Wake-up frame
1949          * is received. Anyway, it's better to manually clear
1950          * this bit because it can generate problems while resuming
1951          * from another devices (e.g. serial console). */
1952         if (device_may_wakeup(priv->device))
1953                 priv->hw->mac->pmt(priv->ioaddr, 0);
1954
1955         netif_device_attach(ndev);
1956
1957         /* Enable the MAC and DMA */
1958         stmmac_set_mac(priv->ioaddr, true);
1959         priv->hw->dma->start_tx(priv->ioaddr);
1960         priv->hw->dma->start_rx(priv->ioaddr);
1961
1962 #ifdef CONFIG_STMMAC_TIMER
1963         if (likely(priv->tm->enable))
1964                 priv->tm->timer_start(tmrate);
1965 #endif
1966         napi_enable(&priv->napi);
1967
1968         netif_start_queue(ndev);
1969
1970         spin_unlock(&priv->lock);
1971
1972         if (priv->phydev)
1973                 phy_start(priv->phydev);
1974
1975         return 0;
1976 }
1977
1978 int stmmac_freeze(struct net_device *ndev)
1979 {
1980         if (!ndev || !netif_running(ndev))
1981                 return 0;
1982
1983         return stmmac_release(ndev);
1984 }
1985
1986 int stmmac_restore(struct net_device *ndev)
1987 {
1988         if (!ndev || !netif_running(ndev))
1989                 return 0;
1990
1991         return stmmac_open(ndev);
1992 }
1993 #endif /* CONFIG_PM */
1994
1995 #ifndef MODULE
1996 static int __init stmmac_cmdline_opt(char *str)
1997 {
1998         char *opt;
1999
2000         if (!str || !*str)
2001                 return -EINVAL;
2002         while ((opt = strsep(&str, ",")) != NULL) {
2003                 if (!strncmp(opt, "debug:", 6)) {
2004                         if (strict_strtoul(opt + 6, 0, (unsigned long *)&debug))
2005                                 goto err;
2006                 } else if (!strncmp(opt, "phyaddr:", 8)) {
2007                         if (strict_strtoul(opt + 8, 0,
2008                                            (unsigned long *)&phyaddr))
2009                                 goto err;
2010                 } else if (!strncmp(opt, "dma_txsize:", 11)) {
2011                         if (strict_strtoul(opt + 11, 0,
2012                                            (unsigned long *)&dma_txsize))
2013                                 goto err;
2014                 } else if (!strncmp(opt, "dma_rxsize:", 11)) {
2015                         if (strict_strtoul(opt + 11, 0,
2016                                            (unsigned long *)&dma_rxsize))
2017                                 goto err;
2018                 } else if (!strncmp(opt, "buf_sz:", 7)) {
2019                         if (strict_strtoul(opt + 7, 0,
2020                                            (unsigned long *)&buf_sz))
2021                                 goto err;
2022                 } else if (!strncmp(opt, "tc:", 3)) {
2023                         if (strict_strtoul(opt + 3, 0, (unsigned long *)&tc))
2024                                 goto err;
2025                 } else if (!strncmp(opt, "watchdog:", 9)) {
2026                         if (strict_strtoul(opt + 9, 0,
2027                                            (unsigned long *)&watchdog))
2028                                 goto err;
2029                 } else if (!strncmp(opt, "flow_ctrl:", 10)) {
2030                         if (strict_strtoul(opt + 10, 0,
2031                                            (unsigned long *)&flow_ctrl))
2032                                 goto err;
2033                 } else if (!strncmp(opt, "pause:", 6)) {
2034                         if (strict_strtoul(opt + 6, 0, (unsigned long *)&pause))
2035                                 goto err;
2036 #ifdef CONFIG_STMMAC_TIMER
2037                 } else if (!strncmp(opt, "tmrate:", 7)) {
2038                         if (strict_strtoul(opt + 7, 0,
2039                                            (unsigned long *)&tmrate))
2040                                 goto err;
2041 #endif
2042                 }
2043         }
2044         return 0;
2045
2046 err:
2047         pr_err("%s: ERROR broken module parameter conversion", __func__);
2048         return -EINVAL;
2049 }
2050
2051 __setup("stmmaceth=", stmmac_cmdline_opt);
2052 #endif
2053
2054 MODULE_DESCRIPTION("STMMAC 10/100/1000 Ethernet device driver");
2055 MODULE_AUTHOR("Giuseppe Cavallaro <peppe.cavallaro@st.com>");
2056 MODULE_LICENSE("GPL");