target/linux/ramips/dts/WZR-AGL300NH.dts

   1 /dts-v1/;
   2
   3 #include "rt2880.dtsi"
   4
   5 #include <dt-bindings/input/input.h>
   6
   7 / {
   8         #address-cells = <1>;
   9         #size-cells = <1>;
  10         compatible = "WZR-AGL300NH", "ralink,rt2880-soc";
  11         model = "Buffalo WZR-AGL300NH";
  12
  13         pci@440000 {
  14                 status = "ok";
  15         };
  16
  17         cfi@1f000000 {
  18                 compatible = "cfi-flash";
  19                 reg = <0x1f000000 0x800000>;
  20                 bank-width = <2>;
  21                 device-width = <2>;
  22                 #address-cells = <1>;
  23                 #size-cells = <1>;
  24
  25                 partition@0 {
  26                         label = "uboot";
  27                         reg = <0x0 0x30000>;
  28                         read-only;
  29                 };
  30
  31                 partition@30000 {
  32                         label = "uboot-env";
  33                         reg = <0x30000 0x10000>;
  34                         read-only;
  35                 };
  36
  37                 factory: partition@40000 {
  38                         label = "factory";
  39                         reg = <0x40000 0x10000>;
  40                         read-only;
  41                 };
  42
  43                 partition@50000 {
  44                         label = "firmware";
  45                         reg = <0x50000 0x3b0000>;
  46                 };
  47         };
  48
  49         rtl8366s {
  50                 compatible = "realtek,rtl8366s";
  51                 gpio-sda = <&gpio0 1 0>;
  52                 gpio-sck = <&gpio0 2 0>;
  53         };
  54
  55         gpio-keys-polled {
  56                 compatible = "gpio-keys-polled";
  57                 #address-cells = <1>;
  58                 #size-cells = <0>;
  59                 poll-interval = <100>;
  60
  61                 wps {
  62                         label = "wps";
  63                         gpios = <&gpio0 0 1>;
  64                         linux,code = <KEY_WPS_BUTTON>;
  65                 };
  66
  67                 router {
  68                         label = "router_switch";
  69                         gpios = <&gpio0 7 0>;
  70                         linux,code = <BTN_0>;
  71                 };
  72
  73                 reset {
  74                         label = "reset";
  75                         gpios = <&gpio0 9 1>;
  76                         linux,code = <KEY_RESTART>;
  77                 };
  78         };
  79
  80         gpio-leds {
  81                 compatible = "gpio-leds";
  82
  83                 router {
  84                         label = "wzr-agl300nh:green:router";
  85                         gpios = <&gpio0 8 1>;
  86                 };
  87
  88                 diag {
  89                         label = "wzr-agl300nh:red:diag";
  90                         gpios = <&gpio0 12 1>;
  91                 };
  92
  93                 security_g {
  94                         label = "wzr-agl300nh:orange:security_g";
  95                         gpios = <&gpio0 11 1>;
  96                 };
  97
  98                 security_n {
  99                         label = "wzr-agl300nh:orange:security_n";
 100                         gpios = <&gpio0 13 1>;
 101                 };
 102         };
 103 };
 104
 105 &gpio0 {
 106         status = "okay";
 107 };
 108
 109 &pinctrl {
 110         state_default: pinctrl0 {
 111                 gpio {
 112                         ralink,group = "i2c", "uartlite", "mdio";
 113                         ralink,function = "gpio";
 114                 };
 115         };
 116 };
 117
 118 &ethernet {
 119         status = "okay";
 120         mtd-mac-address = <&factory 0x4>;
 121
 122         port@0 {
 123                 mediatek,fixed-link = <1000 1 1 1>;
 124         };
 125
 126         mdio-bus {
 127                 status = "okay";
 128
 129                 phy0: ethernet-phy@0 {
 130                         phy-mode = "mii";
 131                         reg = <0>;
 132                 };
 133         };
 134 };
 135
 136 &wmac {
 137         ralink,mtd-eeprom = <&factory 0>;
 138 };