Mantas Pucka [Wed, 6 Mar 2019 08:24:33 +0000 (10:24 +0200)]
ar71xx: enable QCA955x SGMII fixup on Rambutan
fixes intermittent loss of connectivity on 1Gbit port, with
log message:
803x_aneg_done: SGMII link is not ok
Signed-off-by: Mantas Pucka <mantas@8devices.com>
David Bauer [Mon, 4 Mar 2019 17:03:57 +0000 (18:03 +0100)]
ath10k-ct: limit available channels via DT
This backports upstream commit
34d5629 ath10k: limit available channels via DT ieee80211-freq-limit
to the 4.19 ath10k-ct version. Without this patch, disabled channels
are still listed as a supported configuration for the radio.
The identical patch was also backported by OpenWRT to the non-ct driver.
It can be dropped as soon as we switch to an ath10k-ct version based on
4.20 or higher.
Signed-off-by: David Bauer <mail@david-bauer.net>
Michael Yartys [Fri, 1 Mar 2019 11:25:40 +0000 (12:25 +0100)]
ath10k-firmware: update Candela Tech firmware images
Release notes since last update:
wave-1 firmware:
* Feb 14, 2019: Remove logic that causes assert when swba logic is not
initialized. This was seen when trying to bring up 6 VAP
vdevs. A similar fix went into wave-2 firmware some time
ago.
* Feb 27, 2019: Support up to 32 vAP vdevs, fix stack corruption when
driver requests too many vAP.
* Feb 28, 2019: Support beacon-tx-wmi callback message. This lets driver
properly clean up beacon buffers so we don't crash
(somethings the entire OS/system) due to DMA errors.
wave-2 firmware:
* Feb 27. 2019: Support up to 32 AP vdevs. Previous to this, stack would
be corrupted if you went past 16 AP vdevs.
* Feb 28, 2019: Support beacon-tx-wmi callback message. This lets driver
properly clean up beacon buffers. In wave-1, this could
crash the entire OS, but I didn't see the same crashes
in wave-2, so maybe it is fixed in some other way. Add
the feature regardless as it seems proper.
Signed-off-by: Michael Yartys <michael.yartys@gmail.com>
Michael Yartys [Sat, 2 Mar 2019 19:50:18 +0000 (20:50 +0100)]
ath10k-ct: Update to 2019-02-28
9360f389234a ath10k: Support up to 24 vAP per radio, fix DMA bug in wave-1.
9cbf8d430974 ath10k-ct: Add 4.20 driver, SGI support for fixed-rate tx.
Runtime tested on: ipq806x
Signed-off-by: Michael Yartys <michael.yartys@gmail.com>
Christian Lamparter [Sat, 2 Mar 2019 21:33:42 +0000 (22:33 +0100)]
lantiq: enlarge ZyXEL P-2812HNU-F1 kernel partition (FS#2124)
The current snapshot release kernel with it's
2119245 Byte
size is too big to fit into the
2097152 (2MiB) area that
was set aside for the kernel. Which causes the device to
fail to boot (after an update or even during a fresh install)
NAND read: device 0 offset 0x60000, size 0x200000
2097152 bytes read: OK
## Booting kernel from Legacy Image at
80800000 ...
Image Name: MIPS OpenWrt Linux-4.14.98
Created: 2019-02-13 9:37:36 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size:
2119245 Bytes = 2 MiB
Load Address:
80002000
Entry Point:
80002000
Verifying Checksum ... Bad Data CRC
ERROR: can't get kernel image!
This patch fixes the problem by enlarging the kernel partition
at the cost of the ubi/data partition behind it. The patch
also adds a KERNEL_SIZE variable to the image Makefile to
prevent silent corruptions from happening in the future.
Please note: The u-boot environment for the router also
needs to be updated. So please attach an appropriate
serial converter cable and enter the following commands
into the u-boot prompt:
setenv nboot 'nand read 0x80800000 0x60000 0x300000; bootm 0x80800000'
saveenv
The wiki has been updated accordingly:
<https://openwrt.org/toh/zyxel/p2812hnu-f1>
Fixes: FS#2124
Suggested-by: Mafketel (User on bugs.openwrt.org)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Daniel Golle [Wed, 6 Mar 2019 13:45:15 +0000 (14:45 +0100)]
ib: display whether profile comes with image metadata
Having image metadata (and signature) appended is a condition for
semi-automated sysupgrade, hence IB needs to be able to tell which
images will end up with metadata.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 5 Feb 2017 14:03:14 +0000 (15:03 +0100)]
ramips: mt7620: export chip version and pkg
Similar to the (currently unused) mt7620_get_eco() function, introduce
mt7620_get_chipver() and mt7620_get_pkg() functions to allow rt2x00 to
probe for the type of WiSoC. This is ugly and probably unacceptable
for upstream, however, it should help to evaluate which of those hacks
are actually really needed, enumerate the possible values and label
them in a more meaningful way than currently done in the vendor driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Paul Spooren [Tue, 5 Mar 2019 23:32:45 +0000 (00:32 +0100)]
metadata: add "metadata_version" field
allow downstream projects to see the current version of the metadata,
usefull if eventually more variables change
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Tue, 26 Feb 2019 19:41:52 +0000 (20:41 +0100)]
metadata: add "target" entry
add "target" entry based on $(TARGETID) resulting in
`<target>/<subtarget>`.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Tue, 26 Feb 2019 19:50:49 +0000 (20:50 +0100)]
metadata: fixup "board"
currently the "board" parameter contains $(BOARD) which actually results
to `<target>` (like ramips, ar71xx) without subtarget. However, one
actually excepts (not?) to contain BOARD_NAME or DEVICE_NAME.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Rafał Miłecki [Tue, 5 Mar 2019 22:08:45 +0000 (23:08 +0100)]
kernel: fix refcnt leak in LED netdev trigger on interface rename
This fixes a possible unbalanced dev_hold():
> iw dev bar del
[ 237.355366] unregister_netdevice: waiting for bar to become free. Usage count = 1
[ 247.435362] unregister_netdevice: waiting for bar to become free. Usage count = 1
[ 257.545366] unregister_netdevice: waiting for bar to become free. Usage count = 1
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Jo-Philipp Wich [Wed, 14 Nov 2018 11:49:45 +0000 (12:49 +0100)]
uqmi: inherit firewall zone membership to virtual sub interfaces
Fix an issue where subinterfaces were not added to the same
firewall zone as their parent.
Fixes: FS#2122
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 11 Feb 2019 17:34:38 +0000 (18:34 +0100)]
ar71xx: ag71xx: fix compile error when enabling debug
Starting from kernel 4.5, phy_id needs to be fetched from a different location.
not doing so results in this compile error:
drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.c: In function 'ag71xx_phy_connect_multi':
drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.c:133:35: error: 'struct mdio_device' has no member named 'phy_id'
ag->mii_bus->mdio_map[phy_addr]->phy_id);
^
./include/linux/printk.h:137:18: note: in definition of macro 'no_printk'
printk(fmt, ##__VA_ARGS__); \
^~~~~~~~~~~
drivers/net/ethernet/atheros/ag71xx/ag71xx.h:72:27: note: in expansion of macro 'pr_debug'
#define DBG(fmt, args...) pr_debug(fmt, ## args)
^~~~~~~~
drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.c:130:3: note: in expansion of macro 'DBG'
DBG("%s: PHY found at %s, uid=%08x\n",
^~~
scripts/Makefile.build:326: recipe for target 'drivers/net/ethernet/atheros/ag71xx/ag71xx_phy.o' failed
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Wed, 27 Feb 2019 16:07:48 +0000 (17:07 +0100)]
kernel: bump 4.14 to 4.14.104
Refreshed all patches.
Altered patches:
- 332-arc-add-OWRTDTB-section.patch
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Wed, 27 Feb 2019 16:01:41 +0000 (17:01 +0100)]
kernel: bump 4.9 to 4.9.161
Refreshed all patches.
Altered patches:
- 332-arc-add-OWRTDTB-section.patch
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Vijayakumar Durai [Tue, 26 Feb 2019 13:59:30 +0000 (19:29 +0530)]
mac80211: rt2x00: do not increment sequence number while re-transmitting
Currently STA+AP re-transmitting the management frames with
incremented sequence number if hardware is assigning the sequence.
Fix is to assign the sequence number for Beacon by hardware
and for other Management frames software will assign the
sequence number
Signed-off-by: Vijayakumar Durai <vijayakumar.durai1@vivint.com>
Petr Štetiar [Wed, 12 Dec 2018 20:09:01 +0000 (21:09 +0100)]
ath79: Add support for Ubiquiti Nanostation M (XW)
CPU: AR9342 SoC
RAM: 64 MB DDR2
Flash: 8 MB NOR SPI
Ports: 2x100 MBit (24V PoE in, 24V PoE out), AR8236 switch
WLAN: 2.4/5 GHz
UART: 1 UART
LEDs: Power, 2x Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons: Reset
Flashing instructions using recovery method over TFTP
1. Unplug the ethernet cable from the router.
2. Using paper clip press and hold the router's reset button. Make sure
you can feel it depressed by the paper clip. Do not release the button
until step 4.
3. While keeping the reset button pressed in, plug the ethernet cable
back into the AP. Keep the reset button depressed until you see the
device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
LED2/LED4), this may take up to 25 seconds.
4. You may release the reset button, now the device should be in TFTP
transfer mode.
5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
should work.
6. Plug the PoE injector's LAN cable directly to your computer.
7. Start tftp client and issue following commands:
tftp> binary
tftp> connect 192.168.1.20
tftp> put openwrt-ath79-generic-ubnt-nano-m-xw-squashfs-factory.bin
Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 19 Nov 2018 23:16:27 +0000 (00:16 +0100)]
ath79: gmac: ar934x: Add parser for mii-gmac0-slave
While converting Nanostation M XW from current ar71xx code to ath79 I've
hit one issue, where the ethernet networking wasn't working, so I was
checking every bit in the networking setup path between ar71xx and
ath79.
I've came to the following code in ar71xx/mach-ubnt-xm.c:
static void __init ubnt_xw_init(void) {
...
ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_MII_GMAC0 |
AR934X_ETH_CFG_MII_GMAC0_SLAVE);
...
}
Where this code is setting AR934X_ETH_CFG_MII_GMAC0_SLAVE bit in
AR934X_GMAC_REG_ETH_CFG register, but I couldn't find a way of setting
this bit from DTS, so this patch adds `mii-gmac0-slave` DTS property
which allows setting of this bit in `gmac-config`, which is then used in
Nanostation M XW DTS.
Tested-by: Joe Ayers <ae6xe@arrl.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Chuanhong Guo [Sun, 27 Jan 2019 12:54:47 +0000 (20:54 +0800)]
ath79: qca955x: assert mdio/gmac reset together
This allows resetting gmac registers during initialization.
Also add compatible string for qca955x mdio to enable more mdio
clock dividers.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Sat, 15 Dec 2018 07:57:54 +0000 (15:57 +0800)]
ath79: ar934x: assert mac/mdio reset together for gmac0
This allows resetting gmac registers during initialization.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Sat, 15 Dec 2018 07:44:34 +0000 (15:44 +0800)]
ath79: ag71xx: add support for optional mdio reset
On ar933x and later chips, there are separated mac/mdio resets, but
resetting the entire gmac block with register values requires both
mac_reset and mdio_reset to be asserted together.
Add support for optional mdio reset so that we can do a full reset
if needed.
This patch also replaced deprecated devm_reset_control_get for
mac reset.
To use this feature, the following is needed:
1. drop "simple-mfd" compatible to register mdio0 after gmac init
so that mdio registers aren't reset after initialization.
2. move mdio reset from mdio-bus to its parent eth node.
NOTE: This can't be applied on gmac1 with builtin switch since we
haven't add a feature to defer probe if phy connection failed.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Wed, 9 Jan 2019 14:02:09 +0000 (22:02 +0800)]
ath79: ag71xx: register mdio using of_platform_populate
remove the hacky checking of "simple-mfd" compatible
also add some comments explaining that piece of code.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Sat, 15 Dec 2018 07:35:37 +0000 (15:35 +0800)]
ath79: ag71xx-mdio: get reset control using devm api
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Fri, 14 Dec 2018 16:03:43 +0000 (00:03 +0800)]
ath79: ag71xx: replace alloc_etherdev with devm_alloc_etherdev
using the devm api makes the code simpler.
also drop unneeded memory free from ag71xx_remove since they are
allocated using devm apis.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Fri, 14 Dec 2018 15:38:49 +0000 (23:38 +0800)]
ath79: ag71xx: replace ag71xx_get_phy_if_mode_name() with phy_modes()
phy_modes() in phy.h can convert PHY modes to string with supports
for all available PHY modes.
Also add a space in mode printing to make it look better.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Daniel Golle [Mon, 4 Mar 2019 21:09:36 +0000 (22:09 +0100)]
oxnas: pcie: model shared resource as external pcie-phy driver
Refactor pcie-oxnas to have shared resources in syscon and new pcie-phy
driver. Hopefully this revives PCIe...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 4 Mar 2019 03:04:52 +0000 (04:04 +0100)]
oxnas: convert pcie to builtin_platform_driver
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 3 Mar 2019 21:09:33 +0000 (22:09 +0100)]
oxnas: restart: use register definitions from dt-bindings
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 3 Mar 2019 19:34:15 +0000 (20:34 +0100)]
oxnas: cleanup and improve pcie driver
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Sun, 3 Mar 2019 19:58:52 +0000 (20:58 +0100)]
tools: squashfskit4 should only depend on coreutils on non-linux systems
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Alexander Couzens [Sat, 2 Mar 2019 13:46:57 +0000 (14:46 +0100)]
tools/squashfskit: fix version detection on non-linux system
gnu date is present in our staging_dir which means squashfskit will fail
to build. Prevent also a race condition if coreutils is build after
squashfskit.
To prevent a race condition, depend on coreutils.
Acked-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Felix Fietkau [Fri, 1 Mar 2019 15:55:39 +0000 (16:55 +0100)]
mt76: update to the latest version
3c6df9b mt76: rewrite dma descriptor base and ring size on queue reset
30e757e mt76: mt76x02: when setting a key, use PN from mac80211
fa83406 mt76: mt76x2: implement full device restart on watchdog reset
ead881b mt76: mt76x02: do not sync PN for keys with sw_iv set
ba1d989 mt76: mmio: move mt76x02_set_irq_mask in mt76 module
283ebbe mt76: dma: move mt76x02_init_{tx,rx}_queue in mt76 module
b216d3c mt76: introduce q->stopped parameter
8b437d2 mt76x02: clear sta and vif driver data structures on add
2c62d03 mt76x02: clear running flag when resetting state on restart
6b10cfc mt76: mt76x02: only update the base mac address if necessary
669bc49 mt76: mt76x02: reduce false positives in ED/CCA tx blocking
2ed9382 mt76: mt7603: fix tx status HT rate validation
d2c6823 mt76: mt76x2: fix external LNA gain settings
8ee2259 mt76: mt76x2: fix 2.4 GHz channel gain settings
8bfe6d4 mt76: mt7603: clear ps filtering mode before releasing buffered frames
d13b065 mt76: mt7603: fix up hardware queue index for PS filtered packets
eb1ecc4 mt76: mt7603: notify mac80211 about buffered frames in ps queue
3687eec mt76: mt7603: clear the service period on releasing PS filtered packets
42ab27e mt76: when releasing PS frames, end the service period if no frame was found
461f3b0 mt76: mt76x02: disable ED/CCA by default
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hauke Mehrtens [Thu, 28 Feb 2019 19:41:32 +0000 (20:41 +0100)]
mac80211: Activate DRIVER_11W_SUPPORT for more capable drivers
ieee80211w support is only activated in hostapd when at least one
capable driver is build into the image. Many drivers which are capable
of ieee80211 (MFP) and have the MFP_CAPABLE set in the driver are still
missing the DRIVER_11W_SUPPORT dependency. Add this to more driver
capable of ieee80211w.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Daniel Golle [Sun, 3 Mar 2019 01:30:21 +0000 (02:30 +0100)]
oxnas: add SoC restart driver for reboot
Refresh oxnas kernel config while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 2 Mar 2019 18:24:22 +0000 (19:24 +0100)]
ltq-vdsl-fw: update download URL
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 2 Mar 2019 17:53:21 +0000 (18:53 +0100)]
oxnas: cloudengines,pogoplug*: enable USB ports
Reported-by: Jörg Fischer <fischer.loepsingen@yahoo.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Chris Blake [Sat, 2 Mar 2019 02:03:32 +0000 (20:03 -0600)]
mpc85xx: Fix Aerohive HiveAP-330 initramfs image
At some point our initramfs image grew over 6MB, which is
causing an issue when uncompressing in the stock bootloader:
=> bootm 0x5000000 - 0x1000000;
Image Name: Linux-4.19.24
Created: 2019-02-23 1:58:20 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size:
6752470 Bytes = 6.4 MB
Load Address:
00000000
Entry Point:
00000000
Verifying Checksum ... OK
Booting using the fdt blob at 0x1000000
Uncompressing Kernel Image ... Error: inflate() returned -5
GUNZIP: uncompress, out-of-mem or overwrite error - must RESET
board to recover
Loading Device Tree to
00ffa000, end
00fffc78 ... OK
To get around this, we need to move to an uncompressed image
for the initramfs image. While this makes a larger image, it
is thankfully bootable so people can then convert their
devices to run OpenWRT. It's worth noting the non-initramfs
image is under 3M, so it will be ages before we have any issues
with the flashed kernel.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[keep commit message at less than 75 characters per line]
David Bauer [Sun, 24 Feb 2019 23:13:51 +0000 (00:13 +0100)]
ath79: make TP-Link revision naming consistent
This commit makes the TP-Link hardware-revision naming consistent to
match the one used by the vendor. TP-Link refers to the different
revisions as "vX" not "Version X".
Signed-off-by: David Bauer <mail@david-bauer.net>
Kip Porterfield [Sun, 3 Feb 2019 18:54:18 +0000 (13:54 -0500)]
ramips: add support for Belkin F9K1109v1
Device specification:
- SoC: Ralink RT3883 (MIPS 74Kc) 500Mhz
- RAM: 64Mb
- Flash: 8MB (SPI-NOR)
- Ethernet: 10/100/1000 Mbps
- WLAN
Wireless 1: SoC-integrated : 2.4/5 GHz
Wireless 2: 2.4 GHz RT3092L
- LED: 2x USB, WAN, LAN
- Key: WPS, reset
- Serial: 4-pin header, (57600,8,N,1), 3.3V TTL,
GND, RX, TX, V - J12 marking on board
- USB ports: 2 x USB 2.0
Flashing instructions:
Option 1 (from bootloader web)
- Hold reset button on the back of router when plugging
in power (for at-least 10 seconds after plugged in)
- Connect to a Lan port
- Set computer IP to 10.10.10.3
- Go to http://10.10.10.123 in a web browser
- Click the Browse... Button and select the
*squashfs.sysupgrade.bin file then click APPLY
Option 2 (from the stock admin web)
- Go to firmware upgrade
- Upload the **factory** image *initramfs.bin first
- Boot into openwrt
- From Luci web in openwrt upload the *squashfs.sysupgrade.bin
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added v1 to the compatible identifier, added pciid for
the RT3092L, fixed pci unit-address, split out the F9K110X.dtsi
to prepare for a possible F9K1103 patch]
David Santamaría Rogado [Thu, 28 Feb 2019 21:08:48 +0000 (22:08 +0100)]
ath79: TP-Link Archer C7 v4 swap usb led names
Commit
34b10b46 made usb match with the corresponding usb label.
The problem is that v4 seems to use in stock firmware the
upper led for usb 1 and the lower led for usb 2.
The led assigned varies between TP-Link models and even
same model versions. For example, Archer C7 v1 and v2 have
the leds in the reverse order.
Revert
34b10b46 and swap led labels instead, now usb port
and led label match and also respect the original behavior.
Tested-by: Oldrich Jedlicka <oldium.pro@gmail.com>
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Yangbo Lu [Fri, 1 Mar 2019 05:50:08 +0000 (13:50 +0800)]
layerscape: fix VFIO driver build issue since linux-4.14.99
The linux-4.14.99 had introduced below upstream patch.
6636dc5e01c6 arm64: io: Ensure value passed to __iormb() is held in a 64-bit register
It was causing VFIO driver build issue. This patch is to fix it.
CC drivers/vfio/fsl-mc/vfio_fsl_mc.o
In file included from ./include/linux/scatterlist.h:9:0,
from ./include/linux/iommu.h:22,
from drivers/vfio/fsl-mc/vfio_fsl_mc.c:14:
drivers/vfio/fsl-mc/vfio_fsl_mc.c: In function 'vfio_fsl_mc_dprc_wait_for_response':
./arch/arm64/include/asm/io.h:122:45: error: expected expression before ')' token
: "=r" (tmp) : "r" ((unsigned long)(v)) \
^
drivers/vfio/fsl-mc/vfio_fsl_mc.c:334:3: note: in expansion of macro '__iormb'
__iormb();
^~~~~~~
./arch/arm64/include/asm/io.h:122:45: error: expected expression before ')' token
: "=r" (tmp) : "r" ((unsigned long)(v)) \
^
drivers/vfio/fsl-mc/vfio_fsl_mc.c:336:3: note: in expansion of macro '__iormb'
__iormb();
^~~~~~~
Reported-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Christian Lamparter [Tue, 19 Feb 2019 17:52:35 +0000 (18:52 +0100)]
apm821xx: speed up ath9k-caldata extraction
Reading and writing to and from flash storage is slow and currently,
the ath10kcal_extract() scripts are even more at an disadvantage
because they use a block size of 1 to be able skip.
This patch reworks the extraction scripts to be much faster and
efficient by reading and writing the calibration data in possibly
one big block.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Dmitry Tunin [Fri, 22 Feb 2019 12:30:39 +0000 (15:30 +0300)]
ath79: speed up ath9k-eeprom extraction
This is a simple copy of ipq40xx: speed up ath10k-caldata
extraction commit
a69e101ed1169f562fc030a783cd997d3f066b16
Tested on DIR-825-B1
3768+0 records in
3768+0 records out
real 0m 11.90s
user 0m 0.03s
sys 0m 9.94s
1+0 records in
1+0 records out
real 0m 0.03s
user 0m 0.00s
sys 0m 0.03s
With this change eeprom extraction is fast enough to get
working Wi-Fi after initial install.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Christian Lamparter [Thu, 28 Feb 2019 14:43:49 +0000 (15:43 +0100)]
x86: fix geode image builds redux
This patch adds more disabled DRM config symbols from the
x86' config to the generic target configs. The existing
symbols in the x86' configs are kept for now, until we
know whenever we want to remove such symbols or not
(see Github PR #1831, #1825, #1828).
THis patch also contains a squashed patch from
Daniel Engberg <daniel.engberg.lists@pyret.net> titled
"kernel: Fix config for 4.14" which fixes a duplicated line
added by: commit
8bdc241d01eb ("x86: fix geode image builds")
Fixes:
8bdc241d01eb ("x86: fix geode image builds")
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Daniel Golle [Fri, 1 Mar 2019 22:51:19 +0000 (23:51 +0100)]
oxnas: switch to DTS aliases for LEDs and use generic diag.sh
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 1 Mar 2019 22:25:59 +0000 (23:25 +0100)]
iwinfo: update to latest git
b514490 iwinfo: add device id for MediaTek MT7603E
e9e1400 iwinfo: more Ralink and MediaTek WiSoC and PCIe chips
cb108c5 iwinfo: fix capitalization of vendor name
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 1 Mar 2019 21:15:43 +0000 (22:15 +0100)]
oxnas: fix forgotten MTD partition name
Fixes:
858aebc0ef ("oxnas: unify MTD partition names")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Fri, 1 Mar 2019 13:54:31 +0000 (14:54 +0100)]
mac80211: add a fix to prevent unsafe queue wake calls during restart
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 1 Mar 2019 12:10:53 +0000 (13:10 +0100)]
mac80211: backport tx queue start/stop fix
Among other things, it fixes a race condition on calling ieee80211_restart_hw
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Yousong Zhou [Fri, 1 Mar 2019 07:24:21 +0000 (07:24 +0000)]
libubox: bump to version 2019-02-27
Contains the following change
eeef7b5 blobmsg_json: blobmsg_format_string: do not escape '/'
Resolves FS#2147
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Yousong Zhou [Wed, 27 Feb 2019 03:23:45 +0000 (03:23 +0000)]
busybox: sync Config.in files
The change was made with the following commands
cd package/utils/busybox/config
../convert_menuconfig.pl ~/git-repo/openwrt/openwrt/build_dir/target-mips_24kc_musl/busybox-1.30.1
convert_defaults.pl has no changes other than overwriting defaults for
BUSYBOX_DEFAULT_FEATURE_IPV6
Resolves FS#2146
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Yousong Zhou [Wed, 27 Feb 2019 03:22:35 +0000 (03:22 +0000)]
busybox: unindent busybox Config.in
This is to align with upstream change
72089cf ("config: deindent all
help texts") and to make the follow-up change syncing Config.in files
with current busybox version more reviewable
It was made with the following commands
cd package/utils/busybox/config
find . -name 'Config.in' | xargs sed -ir -e 's/^\t \([^ ]\)/\t\1/'
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Adrian Schmutzler [Thu, 28 Feb 2019 18:09:20 +0000 (19:09 +0100)]
ath79: Fix indent
Fix wrong indentation introduced in
59c2f8a.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Daniel Golle [Fri, 1 Mar 2019 05:57:40 +0000 (06:57 +0100)]
mac80211: rt2x00: cleanup ePA, RXIQ and TX-LOFT code
consolidate patch 651-rt2x00-remove-unneccesary-code.patch.
fixup the most obvious whitespace problems in RXIQ and TX-LOFT code.
always backup registers bbpr1, bbpr4, bbpr241 and bbpr242 to avoid
compiler warning about them being potentially uninitialized.
no functional changes (intended)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 1 Mar 2019 02:34:40 +0000 (03:34 +0100)]
mac80211: rt2x00: patch tracking cosmetics
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 1 Mar 2019 01:55:09 +0000 (02:55 +0100)]
oxnas: remove uboot-oxnas-ox820 from default package selection
All supported boards should work with the $vendor bootloader just fine.
Existing users should mindfully re-flash using new initramfs build and
restore $vendor bootloader's bootcmd to it's original setting.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 1 Mar 2019 01:43:48 +0000 (02:43 +0100)]
oxnas: switch to kmod-ledtrig-usb-port
Add port handles for both USB 2.0 ports so they can be used as
trigger-source for USB LEDs.
Suggestions for pogoplug and akitio,mycloud devices are welcome.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 1 Mar 2019 00:56:11 +0000 (01:56 +0100)]
uboot-envtools: oxnas: sync with current oxnas/ox820 DTS
Use tested values on shuttle,kd20 and assumed values for
mitrastar,stg-212 and cloudengines,pogoplug*.
akitio users have yet to report back stock flash layout to support
vendor bootloader environment there as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 1 Mar 2019 00:55:16 +0000 (01:55 +0100)]
oxnas: unify MTD partition names
Use 'u-boot' and 'u-boot-env' like the majority of OpenWrt targets
does...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Alexander Couzens [Thu, 28 Feb 2019 17:43:38 +0000 (18:43 +0100)]
package/ncurses: change AR options to fix reproducible builds
ar has a deterministic (-D) and non-deterministic (-U) mode.
OpenWrt is already using the deterministic mode by default,
but ncurses' configure script force this to be non-deterministic.
Since autoreconf fails to generate a new configure, the configure script
is directly modified.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Alexander Couzens [Thu, 28 Feb 2019 15:37:41 +0000 (16:37 +0100)]
include/kernel: sort autoload modules list to fix reproducible builds
When autoloading more than one modules per packages,
/etc/modules.d/$module depends on the file system ordering.
To test this: use disorderfs on the build_dir and build kmod-sched.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Daniel Golle [Mon, 25 Feb 2019 11:02:15 +0000 (12:02 +0100)]
oxnas: add missing NAND partitions
add kernel and other missing NAND flash partitions to allow booting
using stock loader instead of the 2nd-stage bootloader.
This will ease installation from stock firmware on pogoplugs as well
as stg212 aka. medion nas.
Existing users of OpenWrt on those boards will have to boot initramfs
generated after this commit and subsequently flash first the ubinized
image, then again run initramfs to flash sysupgrade.tar image, and
then restore bootcmd in U-Boot environment back to the original setting
('nboot
60500000 0 440000' or something like that) instead of jumping
into the now no longer used 2nd-stage loader.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
INAGAKI Hiroshi [Mon, 25 Feb 2019 12:14:10 +0000 (21:14 +0900)]
ipq806x: fix LED configuration for NEC Aterm WG2600HP
NEC WG2600HP uses port1 on QCA8337 as a WAN port, so "0x2" should
be used as a portmask instead of "0x1e" for "WAN" LED configuration.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
David Santamaría Rogado [Wed, 27 Feb 2019 14:36:19 +0000 (15:36 +0100)]
ar71xx: Change led trigger from usbdev to usbport
This patch changes all the legacy usbdev leds triggers
to the use usbport. The problem is that the usbdev triggers
get applied as usbport in sysfs but LuCI gets confused and
is not able to show the configuration with usbdev. More
information can be found in the PR:
<https://github.com/openwrt/openwrt/pull/1819>
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[extended commit message]
Bart Lauret [Mon, 25 Feb 2019 18:27:28 +0000 (19:27 +0100)]
ath79: add support for TP-Link Archer C5 v1
TP-Link Archer C5 v1 is a dual band router
based on Qualcomm/Atheros QCA9558 + QCA9880.
Specification:
- 720 MHz CPU
- 128 MB of RAM (Various chips)
- 16 MB of FLASH (Various chips)
- SoC QCA9558 integrated 3T3R 2.4 GHz Wi-Fi
- minipcie slot with 3T3R 5 GHz QCA9880-BR4A
- 5x 10/100/1000 Mbps Ethernet (AR8327N Switch)
- 10x LEDs, 2x software buttons
For further informwation on the device, visit the wiki:
<https://openwrt.org/toh/tp-link/archer-c5-c7-wdr7500>
Signed-off-by: Bart Lauret <bblauret@gmail.com>
David Santamaría Rogado [Sun, 24 Feb 2019 15:28:23 +0000 (16:28 +0100)]
ath79: TP-Link Archer C7 v4 swap usb port leds
USB 1 triggers usb2 led and USB 2 triggers usb1.
Lower LED is usb1 and upper LED usb2.
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Luo chongjun [Fri, 22 Feb 2019 11:46:37 +0000 (19:46 +0800)]
ath79: Modify glinet x750 and AR300m MAC address offsets
In the production of glinet, the MAC address of ethernet port is
only written at the position where the ART area offset address
is 0, and the MAC address of eth1 is added 1 on the basis of eth0.
Signed-off-by: Luo chongjun <luochongjun@gl-inet.com>
David Bauer [Mon, 18 Feb 2019 22:58:34 +0000 (23:58 +0100)]
ipq40xx: add support for FritzBox 7530
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M
FLASH: 128M NAND
ETH: QCA8075
VDSL: Intel/Lantiq VRX518 PCIe attached
currently not supported
DECT: Dialog SC14448
currently not supported
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
LED: - Power/DSL green
- WLAN green
- FON/DECT green
- Connect/WPS green
- Info green
- Info red
BTN: - WLAN
- FON
- WPS/Connect
UART: 115200n8 3.3V (located under the Dialog chip)
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz7530'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ7530.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz7530.bin uboot0
> mtd write /path/to/uboot-fritz7530.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
[removed pcie-dts range node, refreshed on top of AP120-AC/
E2600AC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
David Bauer [Mon, 18 Feb 2019 22:58:33 +0000 (23:58 +0100)]
uboot-fritz4040: bump version to 2019-02-08
Adds support for the AVM FRITZ!Box 7530.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [PKG_RELEASE]
David Bauer [Mon, 18 Feb 2019 22:58:32 +0000 (23:58 +0100)]
scripts: make eva_ramboot.py offset configurable
The current eva_ramboot.py script is currently only compatible with
Lantiq based AVM devices. For IPQ40xx devices, the offset needs to be
changed. Also an alignment is not necessary here.
Adjust the script to be able to pass an optional offset to load the
image to. In case no offset is provided, the script behaves exactly as
before this commit.
Signed-off-by: David Bauer <mail@david-bauer.net>
Christian Lamparter [Tue, 26 Feb 2019 15:22:27 +0000 (16:22 +0100)]
ipq40xx: fix pcie msi IRQ trigger level
From: Niklas Cassel <niklas.cassel@linaro.org>
|The databook clearly states that the MSI IRQ (msi_ctrl_int) is a level
|triggered interrupt.
|
|The msi_ctrl_int will be high for as long as any MSI status bit is set,
|thus the IRQ type should be set to IRQ_TYPE_LEVEL_HIGH, causing the
|IRQ handler to keep getting called, as long as any MSI status bit is set.
|[...]
|Not having the correct IRQ type defined will cause us to lose interrupts,
|which in turn causes timeouts in the PCIe endpoint drivers.
|
|Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
|Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Mon, 25 Feb 2019 20:12:44 +0000 (21:12 +0100)]
ipq40xx: enlarge PCIe BAR size
David Bauer reported that the VDSL modem (attached via PCIe)
on his AVM Fritz!Box 7530 was complaining about not having
enough space in the BAR. A closer inspection of the old
qcom-ipq40xx.dtsi pulled from the GL-iNet repository listed:
| qcom,pcie@80000 {
| compatible = "qcom,msm_pcie";
| reg = <0x80000 0x2000>,
| <0x99000 0x800>,
| <0x40000000 0xf1d>,
| <0x40000f20 0xa8>,
| <0x40100000 0x1000>,
| <0x40200000 0x100000>,
| <0x40300000 0xd00000>;
| reg-names = "parf", "phy", "dm_core", "elbi",
| "conf", "io", "bars";
Matching the reg-names with the listed reg leads to
<0xd00000> as the size for the "bars".
BugLink: https://www.mail-archive.com/openwrt-devel@lists.openwrt.org/msg45212.html
Reported-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Mon, 25 Feb 2019 14:35:23 +0000 (15:35 +0100)]
kernel: owl-loader: fix sparse endian warnings
owl-loader.c:83:21: sparse: warning: incorrect type in assignment (different base types)
owl-loader.c:83:21: sparse: expected unsigned short [usertype] reg
owl-loader.c:83:21: sparse: got restricted __be16 const [usertype] reg
owl-loader.c:84:21: sparse: warning: incorrect type in assignment (different base types)
owl-loader.c:84:21: sparse: expected unsigned int [usertype] val
owl-loader.c:84:21: sparse: got restricted __be16 const [usertype] low_val
owl-loader.c:85:28: sparse: warning: restricted __be16 degrades to integer
Reported-by: kbuild test robot
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sun, 24 Feb 2019 17:58:52 +0000 (18:58 +0100)]
kernel: disable touchscreen symbols
This patch removes the obsolete touchscreen config symbols
and all disables all remaining ones in the generic config.
Generated by running drivers/input/touchscreen/Kconfig
sed -n 's/^config[[:space:]]\(.*\)/# CONFIG_\1 is not set/p' Kconfig |\
sort -d
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Thu, 21 Feb 2019 18:34:37 +0000 (19:34 +0100)]
x86: fix geode image builds
This patch adds the disabled DRM_RADEON and DRM_AMDGPU
config symbols from the x86' config to the generic target
configs. The existing symbols in the x86' configs are kept
for now, until we know whenever we want to remove such
symbols or not (see Github PR #1831, #1825, #1828).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
张鹏 [Mon, 21 Jan 2019 05:28:32 +0000 (13:28 +0800)]
ipq40xx: add support for Qxwlan
E2600AC C1 and C2
Qxwlan
E2600AC C1 based on IPQ4019
Specifications:
SOC: Qualcomm IPQ4019
DRAM: 256 MiB
FLASH: 32 MiB Winbond W25Q256
ETH: Qualcomm QCA8075
WLAN: 5G + 5G/2.4G
* 2T2R 2.4/5 GHz
- QCA4019 hw1.0 (SoC)
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
INPUT: Reset buutton
LED: 1x Power ,6 driven by gpio
SERIAL: UART (J5)
UUSB: USB3.0
POWER: 1x DC jack for main power input (9-24 V)
SLOT: Pcie (J25), sim card (J11), SD card (J51)
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Qxwlan
E2600AC C2 based on IPQ4019
Specifications:
SOC: Qualcomm IPQ4019
DRAM: 256 MiB
NOR: 16 MiB Winbond W25Q128
NAND: 128MiB Micron MT29F1G08ABAEAWP
ETH: Qualcomm QCA8075
WLAN: 5G + 5G/2.4G
* 2T2R 2.4/5 GHz
- QCA4019 hw1.0 (SoC)
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
INPUT: Reset buutton
LED: 1x Power, 6 driven by gpio
SERIAL: UART (J5)
USB: USB3.0
POWER: 1x DC jack for main power input (9-24 V)
SLOT: Pcie (J25), sim card (J11), SD card (J51)
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "ubi" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[ added rng node. whitespace fixes, ported 02_network,
ipq-wifi Makefile, misc dts fixes, trivial message changes ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Roger Pueyo Centelles [Sat, 29 Dec 2018 19:44:43 +0000 (20:44 +0100)]
ath79: add support for COMFAST CF-E120A v3
This patch adds support for the COMFAST CF-E120A v3, an outdoor wireless
CPE with two Ethernet ports and a 802.11an radio.
Specifications:
- AR9344 SoC
- 535/400/267 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE-in support
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 5 GHz, up to 25 dBm
- 11 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new one, so a factory reset will be
needed. To do so, once the new firmware is flashed, enter into failsafe
mode by pressing the reset button several times during the boot
process, while while the WAN LED flashes, until it starts flashing
faster. Once in failsafe mode, perform a factory reset as usual.
The U-boot bootloader contains a recovery HTTP server to upload the
firmware. Push the reset button while powering the device on and
keep it pressed for >10 seconds. The recovery page will be at
http://192.168.1.1
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Marcel Jost [Tue, 18 Dec 2018 07:00:52 +0000 (08:00 +0100)]
ramips: add TP-Link TL-WR802N-v4 support
This patch adds support for the TP-Link TL-WR802N-v4.
https://openwrt.org/toh/tp-link/tl-wr802n
Specification:
- MT7628N (580 MHz)
- 64 MB RAM
- 8 MB FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet
- 1x LED
Flash instruction:
The only way to flash the image in TL-WR802N v4 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-wr802n-v4-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
the router and keep button pressed for around 10 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Marcel Jost <majo@icutech.ch>
Thomas Vincent-Cross [Sun, 17 Feb 2019 12:21:42 +0000 (23:21 +1100)]
ramips: use generic board detection for Wavlink WL-WN575A3
Bring Wavlink WL-WN575A3 in line with other Wavlink ramips devices.
Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
Thomas Vincent-Cross [Sun, 17 Feb 2019 12:00:59 +0000 (23:00 +1100)]
ramips: various Wavlink WL-WN575A3 fixes
* assign pinmux groups to gpio function for LEDs/buttons
* rename flash node to be more generic in line with other device nodes
* remove useless/incorrect eeprom property from wmac node
* correct base mac address for embedded switch
Signed-off-by: Thomas Vincent-Cross <me@tvc.id.au>
Jason A. Donenfeld [Wed, 27 Feb 2019 23:36:49 +0000 (00:36 +0100)]
wireguard: bump to 0.0.
20190227
* wg-quick: freebsd: allow loopback to work
FreeBSD adds a route for point-to-point destination addresses. We don't
really want to specify any destination address, but unfortunately we
have to. Before we tried to cheat by giving our own address as the
destination, but this had the unfortunate effect of preventing
loopback from working on our local ip address. We work around this with
yet another kludge: we set the destination address to 127.0.0.1. Since
127.0.0.1 is already assigned to an interface, this has the same effect
of not specifying a destination address, and therefore we accomplish the
intended behavior. Note that the bad behavior is still present in Darwin,
where such workaround does not exist.
* tools: remove unused check phony declaration
* highlighter: when subtracting char, cast to unsigned
* chacha20: name enums
* tools: fight compiler slightly harder
* tools: c_acc doesn't need to be initialized
* queueing: more reasonable allocator function convention
Usual nits.
* systemd: wg-quick should depend on nss-lookup.target
Since wg-quick(8) calls wg(8) which does hostname lookups, we should
probably only run this after we're allowed to look up hostnames.
* compat: backport ALIGN_DOWN
* noise: whiten the nanoseconds portion of the timestamp
This mitigates unrelated sidechannel attacks that think they can turn
WireGuard into a useful time oracle.
* hashtables: decouple hashtable allocations from the main device allocation
The hashtable allocations are quite large, and cause the device allocation in
the net framework to stall sometimes while it tries to find a contiguous
region that can fit the device struct. To fix the allocation stalls, decouple
the hashtable allocations from the device allocation and allocate the
hashtables with kvmalloc's implicit __GFP_NORETRY so that the allocations fall
back to vmalloc with little resistance.
* chacha20poly1305: permit unaligned strides on certain platforms
The map allocations required to fix this are mostly slower than unaligned
paths.
* noise: store clamped key instead of raw key
This causes `wg show` to now show the right thing. Useful for doing
comparisons.
* compat: ipv6_stub is sometimes null
On ancient kernels, ipv6_stub is sometimes null in cases where IPv6 has
been disabled with a command line flag or other failures.
* Makefile: don't duplicate code in install and modules-install
* Makefile: make the depmod path configurable
* queueing: net-next has changed signature of skb_probe_transport_header
A 5.1 change. This could change again, but for now it allows us to keep this
snapshot aligned with our upstream submissions.
* netlink: don't remove allowed ips for new peers
* peer: only synchronize_rcu_bh and traverse trie once when removing all peers
* allowedips: maintain per-peer list of allowedips
This is a rather big and important change that makes it much much faster to do
operations involving thousands of peers. Batch peer/allowedip addition and
clearing is several orders of magnitude faster now.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Alexander Couzens [Wed, 12 Dec 2018 15:10:42 +0000 (16:10 +0100)]
tools: migrate from squashfs4 to squashfskit4
squashfskit is a fork of the squashfs-tools.
squashfskit creates reproducible filesystems and includes
many of the distro patches.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: Paul Spooren <mail@aparcar.org>
Eneas U de Queiroz [Wed, 27 Feb 2019 21:06:44 +0000 (18:06 -0300)]
openssl: bump to release 1.1.1b
This is bugfix release that incorporated all of the devcrypto engine
patches currently in the tree.
The cleaning procedure in Package/Configure was not removing the
dependency files, causing linking errors during a rebuild with
different options. It was replaced by a simple make clean.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Hans Dedecker [Wed, 27 Feb 2019 11:10:20 +0000 (12:10 +0100)]
odhcpd: update to latest git HEAD
16c5b6c ubus: always trigger an update if interface is not found
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
David Santamaría Rogado [Tue, 26 Feb 2019 23:14:17 +0000 (00:14 +0100)]
omcproxy: define configuration file
omcproxy's configuration is lost on every update or installation.
Avoid it by defining the configuration file.
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Mantas Pucka [Mon, 25 Feb 2019 16:29:13 +0000 (18:29 +0200)]
Revert "iw: compile with LTO enabled"
After update to 5.0.1 iw-full package failed to display command list on
ipq40xx arch. Root cause was found to be LTO reordering causing
incorrect detection of command struct size in:
iw.c:552
cmd_size = labs((long)&__section_set - (long)&__section_get);
This reverts commit
ef16a394d2b24a363b50b5b4720cb23fe156c9da.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Hauke Mehrtens [Tue, 26 Feb 2019 20:12:18 +0000 (21:12 +0100)]
strace: update to version 2.26
The new patch is a backport from current strace master.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Syrone Wong [Sun, 16 Dec 2018 10:44:43 +0000 (18:44 +0800)]
tools/isl: update to 0.20
Signed-off-by: Syrone Wong <wong.syrone@gmail.com>
Daniel Engberg [Sat, 9 Feb 2019 01:22:02 +0000 (01:22 +0000)]
toolchain/binutils: Add binutils 2.32
Add binutils 2.32 to repo
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Daniel Engberg [Sat, 23 Feb 2019 01:45:42 +0000 (01:45 +0000)]
toolchain: Update to GCC 8.3.0
Update GCC to 8.3.0
Refresh patches
Allow GCC to be used for ARC
Source: https://github.com/openwrt/openwrt/pull/1803#issuecomment-
462334890
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Daniel Engberg [Sat, 23 Feb 2019 09:47:54 +0000 (10:47 +0100)]
toolchain/gcc: Remove workaround for GCC 4.8
GCC 4.8 was removed a long time ago...
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Daniel Engberg [Sun, 24 Feb 2019 07:08:14 +0000 (08:08 +0100)]
popt: Use modern toolchain logic
Replace define Build/Configure with CONFIGURE_ARGS
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Matt Merhar [Tue, 26 Feb 2019 13:05:07 +0000 (08:05 -0500)]
elfutils: fix install .so glob
Only libelf was being packaged correctly - libdw and libasm included
just the symlinks.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Aleksander Jan Bajkowski [Wed, 20 Feb 2019 13:17:45 +0000 (14:17 +0100)]
sunxi: add support for Orange Pi One
CPU: H3 Quad-core Cortex-A7 H.265/HEVC 4K @ 1.2 Ghz
GPU: Mali400MP2 GPU @ 600MHz (supports OpenGL ES 2.0)
Memory: 512MB DDR3 (shared with GPU)
Onboard: Storage TF card (Max. 64GB) / MMC card slot
Onboard header: SPI, I2C, GPIO, UART
USB 2.0: One USB 2.0 HOST, One USB 2.0 OTG
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
David Bauer [Fri, 22 Feb 2019 23:25:07 +0000 (00:25 +0100)]
ath79: fix support-list for TP-Link WDR3600
The TP-Link WDR3600 shares the same machine-code in the ar71xx target,
thus expecting "tl-wdr4300" not "tl-wdr3600" in the support-list
metadata to allow non-forced sysupgrades from ar71xx to ath79.
With this, it is possible to flash a WDR4300 image on the WDR3600. It
is no problem however, as the only difference is the 5GHz WiFi chip
which has 3SS instead of 2SS. Both work with either image.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sat, 23 Feb 2019 12:12:49 +0000 (13:12 +0100)]
ath79: add ar71xx support-list entry for Fritz4020
This adds the support-list entry the AVM FRITZ!Box 4020 expects in the
ar71xx target to allow non-forced sysupgrades from ar71xx to ath79.
Signed-off-by: David Bauer <mail@david-bauer.net>
Andreas Ziegler [Mon, 25 Feb 2019 00:19:59 +0000 (01:19 +0100)]
ar71xx: GL.iNet AR300M family: correct LED definitions
remove USB as this is no LED but power control
rename WiFi LED with correct color red (like in stock firmware)
set middle LED to be used for LAN link/activity
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
Sven Eckelmann [Mon, 25 Feb 2019 19:42:28 +0000 (20:42 +0100)]
ath10k-ct: fix incorrect multicast/broadcast rate setting
If no mcast_rate is set for the wifi-iface then there is no rate_idx (0)
set for the bss. This can break for example 5GHz meshpoint interfaces
because 0 maps to a CCK rate (11Mbit/s).
It must also be avoided that the ath10k-ct internal state for the rates is
not synced with the mac80211 rates state. Otherwise, the user specified
rate (e.g. a wifi-iface mcast_rate for a meshpoint interface) will only be
set on startup. And a short while after that, ath10k-ct specific code in
ath10k_check_apply_special_rates is missing a valid rate in its own
structures and is then recalculating a new default rate. This default rate
is in most situations not the requested rate.
Fixes:
4df3c71cd4c5 ("ath10k-ct: Update to 2018-12-11 and use version based on 4.19")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Sven Eckelmann [Mon, 25 Feb 2019 19:42:28 +0000 (20:42 +0100)]
mac80211: ath10k: fix incorrect multicast/broadcast rate setting
If no mcast_rate is set for the wifi-iface then there is no rate_idx (0)
set for the bss. This breaks for example 5GHz meshpoint interfaces because
0 maps to a CCK rate (11Mbit/s).
Fixes:
db90c243a0b9 ("mac80211: update to version based on 4.19-rc4")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Hauke Mehrtens [Tue, 26 Feb 2019 19:41:03 +0000 (20:41 +0100)]
mac80211: Add WDS / 4addr fix for ath10k supported devices
This should fix the WDS / 4addr mode with ath10k and probably other
devices.
This patch was found here: https://patchwork.kernel.org/patch/
10692383/
Fixes:
d9eefa7a7031 ("mac80211: rebase ontop of v4.18.5")
Reported-by: Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>