Michal Cieslakiewicz [Tue, 12 Nov 2019 13:02:14 +0000 (14:02 +0100)]
ath79: enable all space on Netgear ar9344-based WNDR routers
Netgear WNDR routers (AR9344 models) like WNDR4300 have 128 MiB of flash
memory but only first 32 MiB are used now - both by vendor's firmware and
OpenWrt. This patch concatenates two regions of flash memory: ubi part
of firmware partition and reserved (unused) space beyond 'caldata_backup'
while preserving ART backup. No data is wiped or moved away.
This increases area for OS ubi volumes from 23 to 119 Megabytes.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Paul Fertser [Tue, 10 Dec 2019 14:24:20 +0000 (17:24 +0300)]
base-files: send informational UDP message each second waiting
The preinit network initialisation and failsafe informational message
are inherently racy as the interface takes some time to become
functional after "ip link set $pi_ifname up" command.
Consider this timing:
[ 12.002713] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 12.008819] IPv6: ADDRCONF(NETDEV_UP): eth1.1: link is not ready
[ 12.118877] random: procd: uninitialized urandom read (4 bytes read)
[ 13.068614] eth1: link up (1000Mbps/Full duplex)
[ 13.073309] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 13.080445] IPv6: ADDRCONF(NETDEV_CHANGE): eth1.1: link becomes ready
Since the UDP message was sent prior to link becoming ready, it was
never seen on the wire.
The default failsafe timeout is set to 2 seconds, so with this patch
there are two attempts to send the message, one spent in vain, and the
other visible in tcpdump on an attached host. Of course, in cases when
the interface is brought up faster it leads to two messages, however it
should be harmless. This patch (almost) doesn't affect normal boot time
while still allowing to enter failsafe reliably with a single button
press, matching the official "generic failsafe" documentation.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Petr Štetiar [Fri, 6 Dec 2019 05:55:24 +0000 (06:55 +0100)]
iputils: move iputils tools to packages feed
iputils has moved from the master tree to the packages feed, and is
switching from the abandoned skbuff.net upstream to
github.com/iputils/iputils.
Ref: https://git.openwrt.org/
556698cedf9e86a0ffe9f148d4e8e733676c26f6
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Ansuel Smith [Sun, 15 Dec 2019 13:08:46 +0000 (14:08 +0100)]
ipq806x: switch to 4.19 kernel version
It has been used by several people for some time already and feedback
has been mostly positive.
Ref: https://github.com/openwrt/openwrt/pull/2472
Tested-by: Hannu Nyman <hannu.nyman@iki.fi> [ipq8065, R7800]
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065, NBG6817]
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[separate commit, commit subject and description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Ansuel Smith [Sun, 15 Dec 2019 13:07:46 +0000 (14:07 +0100)]
ipq806x: update USB3 modules for 4.19
- Use new dwc3-qcom usb driver.
- Drop dwc3-of-simple as we have a dedicated driver now.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[split into separate commit, commit subject facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Pavel Kubelun [Mon, 2 Dec 2019 23:45:47 +0000 (00:45 +0100)]
ipq806x: add missing core1 voltage tolerance
Voltage tolerance is accounted per core, not per cpu, so add
missing DT entry.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Ansuel Smith [Fri, 29 Nov 2019 16:24:14 +0000 (17:24 +0100)]
kernel: make dwc3 usb driver depends on kernel 4.14
- usb-dwc3-of-simple is not used anymore as we have qcom dedicated driver
- usb-phy-qcom-dwc3 is not dependent of dwc3-of-simple
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Ansuel Smith [Thu, 28 Nov 2019 21:29:15 +0000 (22:29 +0100)]
ipq806x: fix tsens driver in 4.19
Added patch:
- 063-3 Fix tsense shared memory problem
Recent changes in ioremap_resource function are causing fails for the
memory areas which are already mapped. This changes are causing tsense
driver failures during initialization:
qcom-tsens 900000.thermal-sensor: tsens init failed
So this patch uses simple ioremap in order to use this shared memory
space.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[commit subject and desciption facelitf]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Christian Lamparter [Wed, 4 Dec 2019 01:57:38 +0000 (02:57 +0100)]
ipq806x: improve mdio gpios list
Improve rediability of gpio mdio list. No functional change.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Christian Lamparter [Wed, 4 Dec 2019 01:28:53 +0000 (02:28 +0100)]
ipq806x: ap161: fix wrong definition stdout
From documentation
https://www.kernel.org/doc/Documentation/devicetree/bindings/chosen.txt
should be just stdout-path
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Christian Lamparter [Wed, 4 Dec 2019 01:28:22 +0000 (02:28 +0100)]
ipq806x: ap148: reorganize dts
Reorganize dts to use tags from ipq8064 dtsi
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Christian Lamparter [Thu, 5 Dec 2019 01:26:30 +0000 (02:26 +0100)]
ipq806x: d7800: fix warning on dtc compilation
There is warning with "property has invalid length (4 bytes)"
related to nand definition. Set size-cells to zero to fix this.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Christian Lamparter [Thu, 5 Dec 2019 01:24:44 +0000 (02:24 +0100)]
ipq806x: r7800: add missing wifi definition for pcie
Add missing wifi compatible definition for r7800 device.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Christian Lamparter [Thu, 5 Dec 2019 00:26:22 +0000 (01:26 +0100)]
ipq806x: use ipq8064 dedicated watchdog
Add missing watchdog to list of compatible timers
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Christian Lamparter [Thu, 5 Dec 2019 00:23:26 +0000 (01:23 +0100)]
ipq806x: add nand and sata tags
Add some tags for nand and sata structure to easily
reference them in other dts.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Christian Lamparter [Thu, 5 Dec 2019 00:25:33 +0000 (01:25 +0100)]
ipq806x: increase drive-strength for pinmux
Increase drive-strength from
https://lore.kernel.org/patchwork/patch/626885/
2mA drive strength is not enough when we connect multiple i2c devices
on the bus with different pull up resistors.
This issue was detected when multiple i2c devices
connected on the other side of level shifters on Linaro sensor board.
Maxing up to 16mA made i2c much stable.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Christian Lamparter [Thu, 5 Dec 2019 00:24:55 +0000 (01:24 +0100)]
ipq806x: add missing gpio and gsbi declaration
Adds missing gpio and gsbi declaration.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Ansuel Smith [Thu, 5 Dec 2019 00:12:55 +0000 (01:12 +0100)]
ipq806x: disable spc on ipq8065 soc
Spc is disabled in ipq8065 board as it does cause cpu lockup
(probably caused by wrong register being set)
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Ansuel Smith [Thu, 5 Dec 2019 00:12:32 +0000 (01:12 +0100)]
ipq806x: set apq8064 regulator to support cpuidle
Set qcom,apq8064-saw2-v1.1-cpu as regulator to make cpuidle work.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Christian Lamparter [Thu, 5 Dec 2019 00:11:01 +0000 (01:11 +0100)]
ipq806x: convert ipq8064 dtsi interrupts
Convert hardcoded interrupts value to types defined in gci include file.
Interrupts sets to 0 are converted to IRQ_TYPE_LEVEL_HIGH to fix
kernel warning. Same fix has been applied to arm64 dts.
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/
1797143
https://patchwork.kernel.org/patch/
10367453/
https://patchwork.kernel.org/patch/
10315315/
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Christian Lamparter [Thu, 5 Dec 2019 01:10:26 +0000 (02:10 +0100)]
ipq806x: use new usb3 implementation
Use new usb3 implementation and refresh dts to the new dwc3 structure
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Christian Lamparter [Mon, 16 Dec 2019 19:29:17 +0000 (20:29 +0100)]
ipq806x: fix missing compatible and rename
- ipq8064 compatible was missing from nbg6817.
- Rename ap148 with a better descriptive name.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[proper authorship of the patch]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Christian Lamparter [Wed, 4 Dec 2019 00:20:45 +0000 (01:20 +0100)]
ipq806x: convert ok to okay in dts
DT spec require okay instead of ok in dts files
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Christian Lamparter [Thu, 28 Nov 2019 21:28:48 +0000 (22:28 +0100)]
ipq806x: refresh 4.19 patches
Reworked:
- 0034 patchset update
Added:
- 080 Add support for pinctrl-msm framework
Removed:
- 0074-ipq806x-usb-Control-USB-master-reset.patch
(we now have a dedicated driver for qcom usb)
- 0047-mtd-nand-Create-a-BBT-flag-to-access-bad-block-marke
(merged upstream)
- 310-msm-adhoc-bus-support
(it looks like it was never actually used in any dts)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[commit subject and description facelift, SoB fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Ansuel Smith [Thu, 28 Nov 2019 20:58:19 +0000 (21:58 +0100)]
kernel: generic: add missing config symbol to 4.19
PCI_V3_SEMI config symbol was found missing in generic kernel config
after ipq806x config refresh to 4.19.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[commit subject and description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Ansuel Smith [Sun, 15 Dec 2019 13:06:02 +0000 (14:06 +0100)]
ipq806x: update 4.19 kernel config
These changes are needed in order to migrate old kernel 4.14 config to
the upcoming kernel version 4.19. Also add missing configuration
options that comes up with this SoC.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[line wrap long commit description, add 4.19 to subject, soc->SoC]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Ansuel Smith [Thu, 28 Nov 2019 20:41:20 +0000 (21:41 +0100)]
ipq806x: copy files from 4.14 to 4.19
This copies files from files-4.14 to files-4.19 directory in order to
get clear diffs for any changes done from now on.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[added missing commit description, refreshed ea8500 and wpq864 DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Lech Perczak [Sun, 8 Dec 2019 14:23:54 +0000 (15:23 +0100)]
ath79: restore gpio-export on TL-WDR3600/4300
This partially reverts commit
32144ba275d163ce6e7d93546ab4414f03f508fb.
This commit replaced gpio-exports in favor of gpio-hogs for enabling USB
power at boot, but this rids the user of control of the USB port power
present on this device for a long time. It was agreed on a mailing list
[1] that this is not the way to go, and this patch breaks a very common
use-case of WWAN modem reset by power cycle, used on a lot USB equipped
routers, hence revert this change until a better solution can be found.
[1] http://lists.infradead.org/pipermail/openwrt-devel/2019-November/020151.html
Tested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[adjusted commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Lech Perczak [Sun, 1 Dec 2019 18:31:32 +0000 (19:31 +0100)]
ath79: add support for TP-Link TL-WR902AC v1
TP-Link TL-WR902AC v1 is a pocket-size, dual-band (AC750), successor of
TL-MR3020 (both devices use very similar enclosure, in same size). New
device is based on Qualcomm QCA9531 v2 + QCA9887. FCC ID: TE7WR902AC.
Specification:
- 650/391/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (GPIO-controlled power)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 5x LED (GPIO-controlled), 2x button, 1x 3-pos switch
- UART pads on PCB (TP1 -> TX, TP2 -> RX, TP3 -> GND, TP4 -> 3V3, jumper
resitors are missing on TX/RX lines)
- 1x micro USB (for power only)
Flash instructions:
Use "factory" image under vendor GUI.
Recovery instructions:
This device contains tftp recovery mode inside U-Boot. You can use it to
flash OpenWrt (use "factory" image) or vendor firmware.
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ath79-generic-tplink_tl-wr902ac-v1-squashfs-factory.bin"
to "wr902acv1_un_tp_recovery.bin" and place it in tftp server dir.
3. Connect PC with LAN port, press the reset button, power up the router
and keep button pressed until WPS LED lights up.
4. Router will download file from server, write it to flash and reboot.
MAC Address summary:
- wlan1 (2.4GHz Wi-Fi): Label MAC
- wlan0 (5GHz Wi-Fi): Offset -1 from label
- eth0 (Wired): Offset +1 from label
Root access over serial line in vendor firmware: root/sohoadmin.
Based on support in ar71xx target by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove size-cells from gpio-export]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Maxim Anisimov [Wed, 18 Dec 2019 07:06:14 +0000 (10:06 +0300)]
ramips: fix portmap for TP-Link Archer C50 v4
According to 02_network portmap is wan=0 lan1=1 lan2=2 lan3=3 lan4=4
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Rafał Miłecki [Thu, 19 Dec 2019 08:16:59 +0000 (09:16 +0100)]
mac80211: brcm: add support for BCM4359 SDIO chipset
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Thu, 19 Dec 2019 07:40:12 +0000 (08:40 +0100)]
mac80211: brcm: backport 5.5 and 5.6 kernel patches
This update doesn't include:
3b1e0a7bdfee brcmfmac: add support for SAE authentication offload
be898fed355e brcmfmac: send port authorized event for FT-802.1X
due to nl80211 dependencies.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Álvaro Fernández Rojas [Wed, 4 Sep 2019 15:22:54 +0000 (17:22 +0200)]
brcm2708: switch to cypress-nvram package
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Wed, 4 Sep 2019 15:21:26 +0000 (17:21 +0200)]
cypress-nvram: add new package
This package contains nvram files for brcmfmac, a mac80211 driver for FullMAC
Cypress devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Kevin Darbyshire-Bryant [Tue, 17 Dec 2019 14:10:13 +0000 (14:10 +0000)]
wireguard: bump to 0.0.
20191212
1ec6ece version: bump snapshot
e13de91 main: remove unused include <linux/version.h>
72eb17c wg-quick: linux: support older nft(8)
1d8e978 global: fix up spelling
e02713e wg-quick: linux: add support for nft and prefer it
b4e3a83 compat: support building for RHEL-8.1 instead of RHEL-8.0
f29e3ac socket: convert to ipv6_dst_lookup_flow for 5.5
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Álvaro Fernández Rojas [Wed, 4 Sep 2019 15:32:08 +0000 (17:32 +0200)]
brcmfmac-board-rpi: remove uneeded package
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Wed, 4 Sep 2019 15:22:54 +0000 (17:22 +0200)]
brcm2708: switch to cypress-firmware package
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Wed, 4 Sep 2019 15:20:36 +0000 (17:20 +0200)]
cypress-firmware: add new package
This package contains firmwares provided by Cypress
See https://community.cypress.com/community/linux
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Imran Khan [Tue, 17 Dec 2019 13:59:28 +0000 (05:59 -0800)]
uboot-envtools: check for config prior to append
In the rare event a pre-populated fw_env.config exists in the rootfs prior
to firstboot, calling fw_setenv after the system has initialised will
annihilate the devices environment due to two identical lines in
fw_env.config.
Check for existence prior to blind appendage.
Signed-off-by: Imran Khan <gururug@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: fixed patch format, improved grep, cosmetics]
Adrian Schmutzler [Mon, 16 Dec 2019 17:07:03 +0000 (18:07 +0100)]
ramips: allow to set switchdev by board in ramips_set_preinit_iface
This adds the option to determine switchdev by board when setting
preinit iface for failsafe. The patch reorganizes the code to use
functions for setting correct switchdev based on SOC and board,
which is supposed to improve readability and maintainability.
In this patch, the ramips_switchdev_from_board function is added
without specifying an actual device using it. This is meant to
make the life of device supporters waiting for merge easier, as
there is less to rebase and keep track of.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Thu, 26 Sep 2019 15:16:33 +0000 (00:16 +0900)]
ramips: add support for ipTIME A104ns
ipTIME A104ns is a 2.4/5GHz band AC750 router, based on MediaTek MT7620A.
Specifications:
- SoC: MT7620A
- RAM: DDR2 64MB
- Flash: SPI NOR 8MB
- WiFi:
- 2.4GHz: SoC internal
- 5GHz: MT7610EN
- Ethernet: 5x 10/100Mbps
- Switch: SoC internal
- USB: 1x 2.0
- UART:
- J2: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
In contrast to to-be-supported A1004ns, the A104ns has no usable
value in 0x1fc40 (uboot), so wan_mac needs to be calculated.
Also note that GPIOs for the LEDs really are inverted compared to
the A1004ns.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[moved state_default to device DTS, reordered properties in wmac,
added comment about wan_mac and LED GPIOs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Sun, 15 Dec 2019 09:16:55 +0000 (18:16 +0900)]
ath79: migrate LED paths of TL-WDR4300 board
TL-WDR4300 board uses only green LED names in DTSI.
This patch adds migration for them.
The actual LED colors on the devices have been reported to vary
across subrevisions (v1.x). Despite, the USB LEDs on the back might
have different color than the other LEDs on the front.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Mon, 16 Dec 2019 13:01:41 +0000 (14:01 +0100)]
ramips: add label MAC address for Edimax RG21S
The Edimax RG21S has a label which bears two MAC addresses:
2.4 GHz (n) and 5 GHz (n+1)
The complete MAC address setup is as follows:
2.4 GHz *:83 factory 0x4, u-boot-env wlanaddr
5 GHz *:84 factory 0x8004
LAN *:83 u-boot-env ethaddr
WAN *:85 u-boot-env wanaddr
Since 2.4 GHz is the first address on the label and the same
as used for ethernet, take this one for label MAC address.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Birger Koblitz [Mon, 16 Dec 2019 12:57:44 +0000 (13:57 +0100)]
ramips: increase SPI frequency for Edimax RG21S
This increases SPI frequency from the relatively low 10 MHz to 40 MHz.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[added commit title/message, split patch]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Birger Koblitz [Mon, 16 Dec 2019 12:55:03 +0000 (13:55 +0100)]
ramips: remove unnecessary nodes in DTS for Edimax RG21S
This sdhci and i2c nodes were copy-pasted, but are not needed as
the device does not provide that functionality. Remove them.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[added commit title/message, split patch]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Jo-Philipp Wich [Tue, 17 Dec 2019 07:33:33 +0000 (08:33 +0100)]
rpcd: update to latest Git HEAD
aaa0836 file: extend exec acl checks to commands with arguments
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
David Bauer [Sat, 14 Dec 2019 18:15:21 +0000 (19:15 +0100)]
ar71xx: indicate upgrade using system LED
This enables the system LED to indicate a running firmware upgrade. This
pattern is used on most platforms provided by the generic base-files
package. ar71xx uses it's own implementation for the system-LED, where
the upgrade case is not yet implemented.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sat, 14 Dec 2019 22:38:02 +0000 (23:38 +0100)]
mac80211: fix txpower when using DFS channels
With this patch, txpower for the PHY is applied when configuring the PHY
instead of the VIF. Otherwise, the configured txpower is not applied for
the first initialized VIF when using DFS channels, as it is currently
applied too early when the CAC hasn't finished.
Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Hans Dedecker [Sun, 15 Dec 2019 19:52:31 +0000 (20:52 +0100)]
odhcpd: update to latest git HEAD
d60f0a6 treewide: optimize syslog priority values
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
David Bauer [Fri, 13 Dec 2019 20:31:50 +0000 (21:31 +0100)]
mpc85xx: add support for Enterasys WS-AP3710i
Hardware
--------
SoC: NXP P1020 (2x e500 @ 800MHz)
RAM: 256M DDR3 (Micron)
FLASH: 32M NOR (Spansion S29GL128S)
BTN: 1x Reset
WiFi: 1x Atheros AR9590 2.4 bgn 3x3
2x Atheros AR9590 5.0 an 3x3
ETH: 1x Gigabit Ethernet (Atheros AR8033)
LED: System (green/red) - Radio{0,1} (green)
LAN (connected to PHY)
- GE blue
- FE green
Serial is a Cisco-compatible RJ45 next to the ethernet port.
115200-N-8 are the settings for OS and U-Boot.
Installation
------------
1. Grab the OpenWrt initramfs, rename it to
01C8A8C0.img. Place it in
the root directory of a TFTP server and serve it at
192.168.200.200/24.
2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot
by pressing Enter when prompted. Credentials are identical to the one
in the APs interface. By default it is admin / new2day.
3. Set the bootcmd so the AP can boot OpenWrt by executing
$ setenv boot_openwrt "setenv bootargs;
cp.b 0xee000000 0x1000000 0x1000000; bootm 0x1000000"
$ setenv bootcmd "run boot_openwrt"
$ saveenv
If you plan on going back to the vendor firmware - the bootcmd for it
is stored in the boot_flash variable.
4. Load the initramfs image to RAM and boot by executing
$ tftpboot 0x1000000 192.168.200.200:
01C8A8C0.img; bootm
5. Make a backup of the "firmware" partition if you ever wish to go back
to the vendor firmware.
6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp
folder.
7. Flash OpenWrt using sysupgrade.
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
DENG Qingfang [Fri, 13 Dec 2019 16:24:19 +0000 (00:24 +0800)]
ramips: add support for JCG JHR-AC876M
JCG JHR-AC876M is an AC2600M router
Hardware specs:
SoC: MT7621AT
2.4GHz: MT7615N 4x4 @ PCIe0
5GHz: MT7615N 4x4 @ PCIe1
Flash: Winbond W25Q128JVSQ 16MiB
RAM: Nanya NT5CB128M16 256MiB
USB 2.0 and 3.0 ports
6 LEDs, 3 of which are connected to SoC GPIO
Reset and WPS buttons
Flash instructions:
Stock to OpenWrt:
Upload factory.bin in stock firmware's upgrade page,
do not preserve settings
OpenWrt to stock:
Push and hold the reset button for 5s while power cycling to
enter recovery mode;
Visit 192.168.1.1 and upload stock firmware
MAC addresses map:
0x0004 *:1c wlan2g/wan/label
0x8004 *:20 wlan5g
0xe000 *:1b lan
0xe006 *:1a not used in stock fw
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Adrian Schmutzler [Thu, 12 Dec 2019 19:26:06 +0000 (20:26 +0100)]
ramips: allow JCG_MAXSIZE in kiB in Build/jcg-header
This allows JCG_MAXSIZE to be specified in kilobytes. This makes
this value more consistent and easier comparable with other size
variables.
This also changes the only occurence of the variable, for Cudy WR1000.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Mon, 11 Nov 2019 16:25:31 +0000 (01:25 +0900)]
ramips: add support for ipTIME A6ns-M
ipTIME A6ns-M is a 2.4/5GHz band AC1900 router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7615
- 5GHz: MT7615
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- UART:
- J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Adrian Schmutzler [Thu, 12 Dec 2019 18:49:55 +0000 (19:49 +0100)]
ramips: DTS style improvements for mt7621_wevo_w2914ns-v2.dtsi
This does several trivial DTS style improvements:
- Move device name compatible to DTS files (and fix compatible in
11acnas.dts)
- Remove xhci node as status is set to okay in mt7621.dtsi already
- 0x0 instead of 0x0000
- Simplify state_default node definition
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Mon, 11 Nov 2019 16:26:44 +0000 (01:26 +0900)]
ramips: add support for ZIO FREEZIO
ZIO FREEZIO is a 2.4/5GHz band AC1200 router, based on MediaTek MT7621A.
Specifications:
- SoC: MT7621AT
- RAM: DDR3 128MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7603EN
- 5GHz: MT7612EN
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- USB: 1x 3.0
- UART:
- J4: 3.3V, RX, TX, GND (3.3V is the square pad) / 57600 8N1
Notes:
- FREEZIO has almost the same board as WeVO W2914NS v2.
- Stock firmware is based on OpenWrt BB.
MAC addresses in factory partition:
0x0004: WiFi 2.4GHz (label_mac-8)
0x002e: WAN (label_mac)
0x8004: WiFi 5GHz (label_mac-4)
0xe000: LAN (label_mac+1)
Installation via web interface:
1. Access web admin page and turn on "OpenWrt UI mode".
2. Flash sysupgrade image through LuCI, with the "Keep settings" option
OFF.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Make sure to NOT preserve settings.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebase, use mt7621_wevo_w2914ns-v2.dtsi]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Roman Bazalevsky [Thu, 5 Dec 2019 14:21:28 +0000 (17:21 +0300)]
sunxi: add support for FriendlyARM Nano PI NEO Air dev board
Hardware:
Allwinner H3 upto 1.2GHz
512MB DDR3 RAM
8GB on-board eMMC - mountable, can be used as boot with custom boot.scr
microSD-card slot
WiFi 802.11n (AP6212A) - working
Bluetooth (AP6212A) - not working for now
Micro-USB OTG + 2*USB headers
UART 3.3V - working
GPIO/I2C/SPI 2.54mm headers
Standard sunxi SD-card installation procedure - copy image to SD card,
insert in into slot and boot. First time you will need UART adapter to
enable on-board wireless (or just build custom image with enabled WiFi).
To boot from eMMC:
- boot from SD
- copy SD image to emmc (dd bs=... if=.... of=/dev/mmcblk2)
- mount eMMC boot partition and replace boot script on it
- unmount, reboot
To use i2c, spi and more uarts - replace dtb on boot partition with
fixed one (use dtc or fdt-tools).
Signed-off-by: Roman Bazalevsky <rvb@rvb.name>
[rebase onto device name consolidation patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Thu, 5 Dec 2019 23:47:18 +0000 (00:47 +0100)]
sunxi: construct DTS name from device node name and SOC
The device part in the SUNXI_DTS variable always corresponds to
device node name. This is another redundancy that can be removed
by calculating the DTS name from a newly introduced SUNXI_SOC
variable and the node name.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Thu, 5 Dec 2019 23:11:56 +0000 (00:11 +0100)]
sunxi: use vendor_device scheme for device definitions
This changes device definition to resemble the vendor_device scheme
already present for the majority of device compatible strings.
By doing this, we achieve several advantages at once:
- Image names and node names are more consistent with other targets.
- SUPPORTED_DEVICES can be set automatically for all but two cases.
- Image names and node names are in line with DEVICE_TITLEs.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Mon, 9 Dec 2019 12:53:21 +0000 (13:53 +0100)]
ath79: add support for TP-Link TL-WDR4300 v1 (IL)
The TL-WDR4300 v1 sold in Israel has a different TPLINK_HWID.
Thanks to Josh4300 for testing on device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Fri, 6 Dec 2019 12:56:51 +0000 (13:56 +0100)]
ath79: redistribute UBNT variables in Ubiquiti image Makefile
The variables UBNT_BOARD and UBNT_VERSION are defined in the parent
Device/ubnt definition and then overwritten for most of the derived
platform definitions (e.g. Device/ubnt-wa).
Since this mixed use of inheritance and overwriting can be misleading,
this moves the variables to the platform-based definitions.
While at it, reorder the definitions to have order consistent, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Mon, 9 Dec 2019 11:56:12 +0000 (12:56 +0100)]
ramips: add label MAC address for Mikrotik RBM33G
The device label contains:
E01: B8:69:F4:xx:xx:07
E02: B8:69:F4:xx:xx:09
The first value corresponds to the address set in hard_config 0x10.
That one is taken for the label MAC address.
Thanks to Martin Schiller for retrieving the information.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 8 Dec 2019 15:15:00 +0000 (16:15 +0100)]
ramips: rt305x: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
This removes the wan_mac setup for the following devices as they
do not set up a MAC address for ethernet in the first place:
- asiarf,awapn2403
- belkin,f7c027
- dlink,dir-615-d
- mofinetwork,mofi3500-3gn
- prolink,pwh2004
- ralink,v22rw-2x2
- unbranded,wr512-3gn-4m
- unbranded,wr512-3gn-8m
While at it, make some DT node labels consistent with the label
property.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 8 Dec 2019 13:55:49 +0000 (14:55 +0100)]
ramips: rt288x: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
This removes the wan_mac setup for ralink,v11st-fe as this device
does not set up a MAC address for ethernet in the first place.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 8 Dec 2019 13:26:34 +0000 (14:26 +0100)]
ramips: mt76x8: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
While at it, change the partition label for zyxel,keenetic-extra-ii
to factory to be consistent with node label and all the other devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 8 Dec 2019 12:42:39 +0000 (13:42 +0100)]
ramips: mt7621: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 8 Dec 2019 12:20:50 +0000 (13:20 +0100)]
ramips: mt7620: use flash location for wan_mac in 02_network
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 8 Dec 2019 12:23:56 +0000 (13:23 +0100)]
ramips: remove wan_mac setup for evaluation boards
The evaluation boards do not set up a MAC address for eth0
in the first place, so it does not make sense to calculate a WAN
address from the random MAC used there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 8 Dec 2019 11:51:20 +0000 (12:51 +0100)]
ramips: create common DTSI for TP-Link Archer C20i/C20 v1/C50 v1
The TP-Link Archer C20i/C20 v1/C50 v1 seem to be almost the same,
so creating a common DTSI will reduce duplicate code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sat, 7 Dec 2019 22:37:40 +0000 (23:37 +0100)]
ramips: remove unused DTS variable from DEVICE_VARS
The DTS variable has been removed in
402138d12dca ("ramips: Derive
DTS name from device name in Makefile"), but the DEVICE_VARS entry
has been overlooked.
Remove it now since we are not using this variable.
This must _not_ be backported to 19.07, where the variable is still
in use.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Gabor Varga [Mon, 9 Dec 2019 22:03:58 +0000 (23:03 +0100)]
ramips: fix switch port numbering for RT-AC65P/RT-AC85P
The switch LAN port numbers are in reversed order with original config.
With this patch they are fixed.
Port order checked on both devices.
Signed-off-by: Gabor Varga <vargagab@gmail.com>
[merged definitions into appropriate block, extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 8 Dec 2019 11:28:22 +0000 (12:28 +0100)]
ramips: add label MAC address for TP-Link Archer C20i
Current OpenWrt MAC setup:
eth0 &rom 0xf100 :48
eth0.2 eth0+1 :49
wlan0 (5 GHz) &radio 0x8004 different OUI
wlan1 (2.4 GHz) &radio 0x4 same OUI as wlan0
Label MAC address corresponds to eth0 (ðernet).
No additional addresses found in hexdump of rom/radio.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
DENG Qingfang [Sat, 7 Dec 2019 16:37:31 +0000 (00:37 +0800)]
ath79: fix typos in DTS
Replace "usb_ochi" with "usb_ohci", and "usb_echi" with "usb_ehci".
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Hans Dedecker [Wed, 11 Dec 2019 21:27:26 +0000 (22:27 +0100)]
glibc: update to latest 2.27 commit (BZ #2503, BZ #2504)
bef0b1cb31 libio: Disable vtable validation for pre-2.1 interposed handles [BZ #25203]
4d5cfeb510 rtld: Check __libc_enable_secure before honoring LD_PREFER_MAP_32BIT_EXEC (CVE-2019-19126) [BZ #25204]
92f04eedb5 mips: Force RWX stack for hard-float builds that can run on pre-4.8 kernels
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Koen Vandeputte [Mon, 9 Dec 2019 10:47:01 +0000 (11:47 +0100)]
ath10k-firmware: update Candela Tech firmware images
The release notes since last time for wave-1:
* November 29, 2019: Fix IBSS merge issue, related to TSF id leakage bug in firmware code.
Thanks for Ahmed Zaki @ Mage-Networks for helping to diagnose and test.
The release notes since last time for wave-2:
* December 6, 2019: Fix 160Mhz problem caused by logic that did not take into account the fact that
160Mhz has only 1/2 of the NSS of lower bandwidths in the rate table.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Fri, 6 Dec 2019 15:25:06 +0000 (16:25 +0100)]
kernel: bump 4.19 to 4.19.88
Refreshed all patches.
Remove upstreamed:
- 0004-boot-sq201-from-sda1.patch
- 500-v4.20-ubifs-Fix-default-compression-selection-in-ubifs.patch
- 0003-usb-dwc2-use-a-longer-core-rest-timeout-in-dwc2_core.patch
Altered patches:
- 0011-ARM-dts-Fix-up-SQ201-flash-access.patch
- 400-mtd-add-rootfs-split-support.patch
- 0101-pci-mediatek-backport-fix-pcie.patch
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Fri, 6 Dec 2019 13:55:57 +0000 (14:55 +0100)]
kernel: bump 4.14 to 4.14.158
Refreshed all patches.
Altered patches:
- 400-mtd-add-rootfs-split-support.patch
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Fri, 6 Dec 2019 13:06:33 +0000 (14:06 +0100)]
kernel: bump 4.9 to 4.9.206
Refreshed all patches.
Altered patches:
- 400-mtd-add-rootfs-split-support.patch
Compile-tested on: none
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Daniel Golle [Mon, 9 Dec 2019 19:16:53 +0000 (20:16 +0100)]
malta: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 9 Dec 2019 19:15:36 +0000 (20:15 +0100)]
sunxi: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 9 Dec 2019 19:15:02 +0000 (20:15 +0100)]
layerscape: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 9 Dec 2019 19:13:41 +0000 (20:13 +0100)]
kirkwood: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 9 Dec 2019 19:12:41 +0000 (20:12 +0100)]
at91: disable legacy PTYs and virtual terminals
Enabling legacy PTYs causes problems with procd-hotplug.
And as this is a headless target, no need to have virtual terminals.
Remove corresponding kernel config options, they are disabled in
generic kernel config.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 9 Dec 2019 19:11:18 +0000 (20:11 +0100)]
mpc85xx: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 9 Dec 2019 19:10:18 +0000 (20:10 +0100)]
ixp4xx: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 9 Dec 2019 19:09:13 +0000 (20:09 +0100)]
uml: remove CONFIG_LEGACY_PTY from kernel config
Having legacy PTYs enabled causes problems with procd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 9 Dec 2019 19:07:00 +0000 (20:07 +0100)]
oxnas: disable legacy PTYs and virtual terminals
Enabling legacy PTYs causes problems with procd-hotplug.
And as this is a headless target, no need to have virtual terminals.
Remove corresponding kernel config options, they are disabled in
generic kernel config.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 5 Dec 2019 20:17:58 +0000 (21:17 +0100)]
mac80211: don't call md5sum on non-existing file
If no AP is configured, hostapd-${phy}.conf is not being created,
hence md5sum fails and causes log pollution:
netifd: radio1 (3183): md5sum: can't open '/var/run/hostapd-phy1.conf': No such file or directoy
Hence make sure the file exists when calling md5sum.
Fixes:
a5bc9787d4 ("mac80211: add support for dynamically reconfiguring wifi")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 5 Dec 2019 17:35:36 +0000 (18:35 +0100)]
hostapd: re-introduce process tracking
Before commit
60fb4c92b6 ("hostapd: add ubus reload") netifd was
tracking hostapd/wpa_supplicant and restarting wifi in case of a
process crash. Restore this behaviour by tracking the PIDs of
hostapd and wpa_supplicant.
Also make sure hostapd and/or wpa_supplicant have been started before
emmitting ubus calls to them using ubus wait_for.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 5 Dec 2019 17:22:55 +0000 (18:22 +0100)]
mac80211: track unmanaged interfaces
In addition to wpa_supplicant and hostapd managed interfaces, also
track unmanaged interfaces. This is used to make sure that running
'wifi' always returns into a clean state regardless of what the user
did before.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Wed, 4 Dec 2019 23:26:53 +0000 (00:26 +0100)]
hostapd: manage instances via procd instead of pidfile
Allows graceful restart of crashing hostapd/wpa_supplicant instances
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: attempt to launch only present services]
Felix Fietkau [Wed, 4 Dec 2019 23:01:28 +0000 (00:01 +0100)]
hostapd: fix crash regression triggered by mesh mode
Fixes:
60fb4c92b6 ("hostapd: add ubus reload")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: polish commit message]
Adrian Schmutzler [Sat, 23 Nov 2019 10:44:51 +0000 (11:44 +0100)]
treewide: remove dts-v1 identifier from DTSI files
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.
This removes the identifier from all DTSI files in /target/linux.
Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx
This does not touch ipq806x for now, as the bump to 4.19 is close.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
David Bauer [Thu, 5 Dec 2019 18:29:14 +0000 (19:29 +0100)]
hostapd: enable CTRL_IFACE_MIB for hostapd-full
This enables the CTRL_IFACE_MIB symbol for wpad-full and hostapd-full.
If it is not enabled, statistic outputs such as "hostapd_cli all_sta"
are empty.
Signed-off-by: David Bauer <mail@david-bauer.net>
Olli Asikainen [Fri, 15 Nov 2019 15:07:37 +0000 (17:07 +0200)]
brcm47xx: add switch configuration for WNR3500L
Netgear WNR3500L is an already supported device, but out of the
box, the device has no switch configuration and there is no wan.
The correct configuration for this specific model is similar to
some other models. This simple commit adds the correct switch
and the out-of-the-box experience is improved.
Experimentally determined:
Port 0 => WAN
Port 1..4 => LAN
Port 5..7 => unused
Port 8 => CPU
Signed-off-by: Olli Asikainen <olli.asikainen@gmail.com>
Tested-by: Fabian Zaremba <fabian@youremail.eu>
[added port mapping to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sat, 7 Dec 2019 23:09:25 +0000 (00:09 +0100)]
ramips: convert mediatek,mtd-eeprom from decimal to hex notation
A small subset of devices uses decimal notation for mediatek,mtd-eeprom
in DTS files. Convert to hexadecimal notation to be consistent with
all the rest.
Also change "0" to "0x0" in the same files for consistency.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Martin Schiller [Wed, 4 Dec 2019 09:43:02 +0000 (10:43 +0100)]
ramips: fix number of LAN Ports for Mikrotik RBM33G
The Mikrotik RBM33G has only 2 LAN ports.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[moved node in 02_network to maintain alphabetic sorting]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Walter Sonius [Wed, 4 Dec 2019 20:07:58 +0000 (21:07 +0100)]
ramips: fix switch port order for TP-Link Archer C20i
Physical port order watched from the backside of the C20i
(from left to right) is: Internet / 1 / 2 / 3 / 4
Physical Port Switch port
WAN 0
LAN 3 1
LAN 4 2
LAN 1 3
LAN 2 4
(not used) 5
CPU 6
Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[commit message/title improvements]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Christian Lamparter [Wed, 15 Aug 2018 15:53:48 +0000 (17:53 +0200)]
ath79: fix WNDR3700/WNDR3800 wifi reg size
"[...] the size component shall be zero."
(See "PCI Bus Binding to: IEEE Std 1275-1994 Rev 2.1"
section "4.1.1 Open Firmware-defined Properties for Child Nodes")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hans Dedecker [Thu, 5 Dec 2019 21:46:50 +0000 (22:46 +0100)]
iproute2: update to 5.4.0
Update iproute2 to latest stable version, see https://lwn.net/Articles/805654/
for the changes in 5.4.0
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
John Crispin [Thu, 5 Dec 2019 09:22:56 +0000 (10:22 +0100)]
mediatek: fix pcie bringup issue
Signed-off-by: John Crispin <john@phrozen.org>
projects / oweals / openwrt.git / log