oweals/openwrt.git
6 years agoath79: rename dts/image using manufacturer_board scheme
Chuanhong Guo [Thu, 2 Aug 2018 07:14:10 +0000 (15:14 +0800)]
ath79: rename dts/image using manufacturer_board scheme

This helps getting rid of SUPPORTED_DEVICES which can be
auto-generated in image/Makefile.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
6 years agoath79: remove quotes for boardname in scripts
Chuanhong Guo [Thu, 2 Aug 2018 07:14:10 +0000 (15:14 +0800)]
ath79: remove quotes for boardname in scripts

Quotes are not required in case statements.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
6 years agoath79: put all devices in alphabetical order in scripts
Chuanhong Guo [Thu, 2 Aug 2018 07:14:10 +0000 (15:14 +0800)]
ath79: put all devices in alphabetical order in scripts

And remove specifying lan interfaces as eth1.1 because this is
handled by ucidef_add_switch.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
6 years agoath79: fix support for TL-MR3020 v1
Chuanhong Guo [Thu, 2 Aug 2018 07:14:10 +0000 (15:14 +0800)]
ath79: fix support for TL-MR3020 v1

Change lan and it's LED to eth0
It's broken since c7c807cb8c3fd6538101de885f66d4681785defe
where I changed the dts but forgot to change default configurations.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
6 years agoath79: fix support for TL-WR740N/WR741N v4
Chuanhong Guo [Thu, 2 Aug 2018 07:14:10 +0000 (15:14 +0800)]
ath79: fix support for TL-WR740N/WR741N v4

1. Swap eth0/eth1
 Both devices are using AR9331, the builtin switch on AR9331 is
 connected to gmac1 and gmac1 is named as eth1 in ath79.
 PS: gmac1 is eth0 and gmac0 is eth1 in ar71xx because of the
 reversed initialization order.
2. Fix the incorrect compatible string in dts

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
6 years agoath79: remove useless phy-handle nodes
Chuanhong Guo [Thu, 2 Aug 2018 07:14:10 +0000 (15:14 +0800)]
ath79: remove useless phy-handle nodes

phy-handle is used to poll link status. They are useless when
we need fixed-link on these interfaces.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
6 years agokernel: modules: fix kmod-regmap redux
Christian Lamparter [Fri, 3 Aug 2018 21:49:22 +0000 (23:49 +0200)]
kernel: modules: fix kmod-regmap redux

Jonas Gorski commented on the previous patch:
|This is actually the wrong fix and papers over an issue in one of our
|local patches.
|
|We intentionally allow regmap to be built as a module, see
|
|/target/linux/generic/hack-4.14/259-regmap_dynamic.patch
|[...]
|[The regulator code] optionally supports regmap thanks to the stubs
|provided if regmap is disabled - which breaks if you compile regmap
|as a module.

In order to mitigate this issue, this patch reverts the previous patch
and replaces the existing IS_ENABLED(CONFIG_REGMAP) with
IS_REACHABLE(CONFIG_REGMAP). This solves this particular issue as the
regulator code will now automatically fallback to the regmap stubs in
case the kmod-regmap module is enabled, but nothing else sets
CONFIG_REGMAP=y.

Note: There's still a potential issue that this patch doesn't solve:
If someone ever wants to make a OpenWrt kernel package for a
regulator module that requires the REGMAP feature for a target that
doesn't set CONFIG_REGMAP=y but has CONFIG_REGULATOR=y, the resulting
kmod-regulator-xyz package will not work on the target.
Luckily, there aren't any in-tree OpenWrt kernel module packages for
regulators at the moment. On the bright side: regmap is a critical
part nowadays and all new and upcoming architectures require it by
default. This will likely only ever be a problem for legacy targets
and devices that cannot afford to enable REGMAP.

Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: John Crispin <john@phrozen.org>
Fixes: d00913d1215b ("kernel: modules: fix kmod-regmap")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
6 years agomt7620: gsw: make IntPHY and ExtPHY share mdio addr 4 possible
Chen Minqiang [Fri, 3 Aug 2018 17:14:07 +0000 (01:14 +0800)]
mt7620: gsw: make IntPHY and ExtPHY share mdio addr 4 possible

To share mdio addr for IntPHY and ExtPHY,
as described in the documentation (MT7620_ProgrammingGuide.pdf).
(refer: http://download.villagetelco.org/hardware/MT7620/MT7620_ProgrammingGuide.pdf)

when port4 setup to work as gmac mode, dts like:

&gsw {
    mediatek,port4 = "gmac";
};

we should set SYSCFG1.GE2_MODE==0x0 (RGMII).
but SYSCFG1.GE2_MODE may have been set to 3(RJ-45) by uboot/default
so we need to re-set it to 0x0

before this changes:
gsw: 4FE + 2GE may not work correctly and MDIO addr 4 cannot be used by ExtPHY

after this changes:
gsw: 4FE + 2GE works and MDIO addr 4 can be used by ExtPHY

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
6 years agoramips: fix gigabit switch PHY access on MDIO
Daniel Gimpelevich [Wed, 1 Aug 2018 14:51:47 +0000 (07:51 -0700)]
ramips: fix gigabit switch PHY access on MDIO

When PHY's are defined on the MDIO bus in the DTS, gigabit support was
being masked out for no apparent reason, pegging all such ports to 10/100.
If gigabit support must be disabled for some reason, there should be a
"max-speed" property in the DTS.

Reported-by: James McKenzie <openwrt@madingley.org>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
6 years agoramips: remove superfluous & confusing DT binding
Daniel Gimpelevich [Wed, 1 Aug 2018 14:44:20 +0000 (07:44 -0700)]
ramips: remove superfluous & confusing DT binding

Mediatek has a reference platform that pairs an MT7620A with an MT7530W,
where the latter responds on MDIO address 0x1f while both chips respond on
0x0 to 0x4. The driver special-cases this arrangement to make sure it's
talking to the right chip, but two different ways in two different places.
This patch consolidates the detection without the current requirement of
both tests to be separately satisfied in the DTS.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
6 years agoramips: add support for Edimax BR-6478AC v2
Daniel Gimpelevich [Mon, 16 Jul 2018 14:19:19 +0000 (07:19 -0700)]
ramips: add support for Edimax BR-6478AC v2

Roll-up of patches by Rohan Murch, Hans Ulli Kroll, and James McKenzie.
Taken from https://forum.openwrt.org/viewtopic.php?id=67192 and updated.

Specification:
- System-On-Chip: MT7620A
- CPU/Speed: 580 MHz
- Flash-Chip: Macronix MX25L6405D
- Flash size: 8192 KiB
- RAM: 64 MiB
- Wireless No1: SoC-integrated: MT7620A 2.4GHz 802.11bgn
- Wireless No2: On-board chip: MT7612E 5GHz 802.11ac
- Switch: Mediatek MT7530W Gigabit Switch
- USB: Yes 1 x 2.0

Installation:
1. Download sysupgrade.bin
2. Open vendor web interface
3. Choose to upgrade firmware
4. After reboot connect via ethernet at 192.168.1.1

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
6 years agoimagebuilder: manifest function show stderr
Paul Spooren [Sun, 5 Aug 2018 03:17:29 +0000 (12:17 +0900)]
imagebuilder: manifest function show stderr

This really simplifies debugging, if a package is not found or a feed is
not reachable, a proper stderr is printed. Currently it would only say
`_call_manifest` failed.

Signed-off-by: Paul Spooren <mail@aparcar.org>
6 years agobase-files: sysupgrade: abort if config backup fails
Andreas Ziegler [Fri, 3 Aug 2018 23:56:39 +0000 (01:56 +0200)]
base-files: sysupgrade: abort if config backup fails

Sysupgrade shouldn't proceed, if the backup of the configuration
fails because tar (or gzip) exit with a non-zero code.

Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
6 years agoscripts: time.pl: avoid hard Time::HiRes dependency
Jo-Philipp Wich [Sun, 5 Aug 2018 10:24:01 +0000 (12:24 +0200)]
scripts: time.pl: avoid hard Time::HiRes dependency

Use Time::HiRes when available and fallback to raw syscall interface
when not. If that fails too, simply report 0, 0 as real time.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6 years agobuild: remove GNU time dependency
Jo-Philipp Wich [Sat, 4 Aug 2018 22:06:27 +0000 (00:06 +0200)]
build: remove GNU time dependency

Replace the GNU time program invocation with a simple Perl script reporting
the timing values. Since we require Perl anyway for the build system, we can
as well use that instead of requiring a random GNU utility rarely installed
by default.

Fixes: ff6e62b288 ("build: log time taken by each packages/steps")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6 years agoramips: move partitions into partition table node
Alex Maclean [Wed, 1 Aug 2018 20:32:34 +0000 (21:32 +0100)]
ramips: move partitions into partition table node

Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
6 years agoramips: unify partition node names in dts files
Mathias Kresin [Fri, 3 Aug 2018 18:14:49 +0000 (20:14 +0200)]
ramips: unify partition node names in dts files

Use partition@ as name for all partition nodes. Add a label where
necessary.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years agoramips: fix whitespace and comment issues in dts
Mathias Kresin [Sun, 22 Jul 2018 08:33:42 +0000 (10:33 +0200)]
ramips: fix whitespace and comment issues in dts

Fix space vs. tabs issue and trainling whitespaces. Use C style
comments or drop the comments if they explain what is already to see in
the devicetree parameters.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years agoramips: fix dtc warnings
Mathias Kresin [Sat, 21 Jul 2018 21:00:20 +0000 (23:00 +0200)]
ramips: fix dtc warnings

Fix individual boards dtc warnings or obvious mistakes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years agoramips: fix hnat dtc warning
Mathias Kresin [Sat, 21 Jul 2018 16:20:59 +0000 (18:20 +0200)]
ramips: fix hnat dtc warning

The hardware NAT node has the same reg/unit as the ethernet node. One
of them need to be a child of the other.

Make the hardware NAT node a child of the ethernet node since the it
"reference" the netdev in its properties.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years agoramips: fix pci/pcie related dtc warnings
Mathias Kresin [Sat, 21 Jul 2018 14:19:46 +0000 (16:19 +0200)]
ramips: fix pci/pcie related dtc warnings

Add the ranges property to the PCI bridges where missing. Add the unit
address to PCI bridge where missing.

Rework the complete rt3883 pci node. Drop the PCI unit nodes from the
dtsi. They are not used by any dts file and should be rather in the dts
than in the SoC dtsi. Express the PCI-PCI bridge in a clean devicetree
syntax. The ralink,pci-slot isn't used by any driver, drop it. Move the
pci interrupt controller out of the pci node. It doesn't share the same
reg and therefore should be an independent/SoC child node.

Move the pci related rt3883 pinctrl setting to the dtsi instead of
defining the very same for each rt3883 board.

If the device_type property is used for PCI units, the unit is treated
as pci bridge which it isn't. Drop it for PCI units.

Reference pci-bridges or the pci node defined in the dtsi instead of
recreating the whole node hierarchy. It allows to change the referenced
node in the dtsi without the need to touch all dts.

Fix the PCI(e) wireless unit addresses. All our PCI(e) wireless chips
are the first device on the bus. The unit address has to be the bus
address instead of the PCI vendor/device id.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years agoramips: use ralink,nr-gpio instead of ralink,num-gpios
Mathias Kresin [Sat, 21 Jul 2018 17:32:51 +0000 (19:32 +0200)]
ramips: use ralink,nr-gpio instead of ralink,num-gpios

Since commit c1e7738988f5 ("checks: add gpio binding properties check")
dtc treats any *-gpios and *-gpio property as phandle at least during
checks. The only whitelisted property is nr-gpio.

Use ralink,nr-gpio in favour of ralink,num-gpios to get rid of false
positive warnings.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years agoramips: fix cpu interrupt controller dtc warnings
Mathias Kresin [Sat, 21 Jul 2018 14:53:10 +0000 (16:53 +0200)]
ramips: fix cpu interrupt controller dtc warnings

The cpu interrupt controller doesn't have a reg property, hence we
can't use a unit address in the node name.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years agoramips: fix cpu related dtc warnings
Mathias Kresin [Sat, 21 Jul 2018 14:17:39 +0000 (16:17 +0200)]
ramips: fix cpu related dtc warnings

We need a reg property if we are using a unit address.

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years agotreewide: convert gpio-export to platform driver
René van Dorst [Thu, 19 Jul 2018 10:55:55 +0000 (12:55 +0200)]
treewide: convert gpio-export to platform driver

Without this patch you will get an error "gpio-export probe deferral
not supported" when you try to export i2c expander gpio pins.

gpio-export is probed long before i2c-bus and i2c expander are created
and it doesn't retry it so none pins are exported.

Signed-off-by: René van Dorst <opensource@vdorst.com>
apply the change to all instances of the gpio exports patch
Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years agoath79: really fix TP-Link Archer C7 v2 MAC address
Mathias Kresin [Wed, 25 Jul 2018 07:03:54 +0000 (09:03 +0200)]
ath79: really fix TP-Link Archer C7 v2 MAC address

Revert 290c54473ead ("ath79: fix TP-Link Archer C7 v2 wlan1 MAC address")
which obviously aims to have a distinct MAC address per interface.

Unfortunally it doesn't match what is used by the stock firmware and we
shouldn'z use MAC Adresses not reserverd for/assigned to a particular
board.

The correct MAC adress increments for this board are:

wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1

Fixes: FS#408

Signed-off-by: Mathias Kresin <dev@kresin.me>
6 years agowireguard: bump to 0.0.20180802
Jason A. Donenfeld [Fri, 3 Aug 2018 20:13:13 +0000 (22:13 +0200)]
wireguard: bump to 0.0.20180802

Changelog taken from the version announcement

> == Changes ==
>
>   * chacha20poly1305: selftest: split up test vector constants
>
>   The test vectors are encoded as long strings -- really long strings -- and
>   apparently RFC821 doesn't like lines longer than 998.
>   https://cr.yp.to/smtp/message.html
>
>   * queueing: keep reference to peer after setting atomic state bit
>
>   This fixes a regression introduced when preparing the LKML submission.
>
>   * allowedips: prevent double read in kref
>   * allowedips: avoid window of disappeared peer
>   * hashtables: document immediate zeroing semantics
>   * peer: ensure resources are freed when creation fails
>   * queueing: document double-adding and reference conditions
>   * queueing: ensure strictly ordered loads and stores
>   * cookie: returned keypair might disappear if rcu lock not held
>   * noise: free peer references on failure
>   * peer: ensure destruction doesn't race
>
>   Various fixes, as well as lots of code comment documentation, for a
>   small variety of the less obvious aspects of object lifecycles,
>   focused on correctness.
>
>   * allowedips: free root inside of RCU callback
>   * allowedips: use different macro names so as to avoid confusion
>
>   These incorporate two suggestions from LKML.
>
> This snapshot contains commits from: Jason A. Donenfeld and Jann Horn.

Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
6 years agouclient: update to latest git HEAD
Jo-Philipp Wich [Fri, 3 Aug 2018 21:50:29 +0000 (23:50 +0200)]
uclient: update to latest git HEAD

f2573da uclient-fetch: use package name pattern in message for missing SSL library
9fd8070 uclient-fetch: Check for nullpointer returned by uclient_get_url_filename
f41ff60 uclient-http: basic auth: Handle memory allocation failure
a73b23b uclient-http: auth digest: Handle multiple possible memory allocation failures
66fb58d uclient-http: Handle memory allocation failure
2ac991b uclient: Handle memory allocation failure for url
63beea4 uclient-http: Implement error handling for header-sending
eb850df uclient-utils: Handle memory allocation failure for url file name
ae1c656 uclient-http: Close ustream file handle only if allocated

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6 years agokernel: bump 4.14 to 4.14.60
Koen Vandeputte [Fri, 3 Aug 2018 08:54:16 +0000 (10:54 +0200)]
kernel: bump 4.14 to 4.14.60

Refreshed all patches

Removed upstreamed patches:
- 500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch

Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
6 years agokernel: bump 4.9 to 4.9.117
Koen Vandeputte [Fri, 3 Aug 2018 08:52:28 +0000 (10:52 +0200)]
kernel: bump 4.9 to 4.9.117

Refreshed all patches

Compile-tested on: ar71xx
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
6 years agosdk: include arch/arm/ Linux includes along with arch/arm64/ ones
Jo-Philipp Wich [Fri, 3 Aug 2018 11:45:27 +0000 (13:45 +0200)]
sdk: include arch/arm/ Linux includes along with arch/arm64/ ones

The Linux headers on arm64 architectures contain references to common
arch/arm/ headers which were not bundled by the SDK so far.

Check if we're packing the SDK for an arm64 target and if we do, also
include arch/arm headers as well.

Fixes FS#1725.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6 years agoiproute2: cake: make gso/gro splitting configurable
Kevin Darbyshire-Bryant [Sun, 29 Jul 2018 13:56:03 +0000 (14:56 +0100)]
iproute2: cake: make gso/gro splitting configurable

This patch makes sch_cake's gso/gro splitting configurable
from userspace.

To disable breaking apart superpackets in sch_cake:

tc qdisc replace dev whatever root cake no-split-gso

to enable:

tc qdisc replace dev whatever root cake split-gso

Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Dave Taht <dave.taht@gmail.com>
[pulled from netdev list - no API/ABI change]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
6 years agokmod-sched-cake: bump to 20180728 optional gso split
Kevin Darbyshire-Bryant [Sat, 28 Jul 2018 20:11:14 +0000 (21:11 +0100)]
kmod-sched-cake: bump to 20180728 optional gso split

Follow upstream kernel patch that restores always splitting gso packets
by default whilst making the option configurable from (tc) userspace.

No ABI/API change

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
6 years agobusybox: update to 1.29.2
Hannu Nyman [Tue, 31 Jul 2018 13:55:42 +0000 (16:55 +0300)]
busybox: update to 1.29.2

* Update busybox to 1.29.2
* refresh default config
* remove upstreamed patches

Config refreshed with
  cd config/
  ../convert_menuconfig.pl ../../../../build_dir/target-arm_cortex-a9+vfpv3_musl_eabi/busybox-1.29.2
  cd ..
  ./convert_defaults.pl < ../../../build_dir/target-arm_cortex-a9+vfpv3_musl_eabi/busybox-1.29.2/.config > Config-defaults.in

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Tested-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agoiperf: bump to 2.0.12
Koen Vandeputte [Thu, 2 Aug 2018 12:40:03 +0000 (14:40 +0200)]
iperf: bump to 2.0.12

Fixes the annoying 'feature' were TTL was set to "1" by default ..
Users had to specify -T manually to test outside the own network.

2.0.12 change set (as of June 25th 2018)

o Change the unicast TTL default value from 1 to the system default (to be compatable with previous versions.) Multicast still defaults to 1.
o adpative formatting bug fix: crash occurs when values exceed 1 Tera. Add support for Tera and Peta and eliminate the potential crash condition
o configure default compile to include isochronous support (use configure --disable-isochronous to remove support)
o replace 2.0.11's --vary-load option with a more general -b option to include <mean>,<stdev>, e.g. -b 100m,40m, which will pull from a log normal distribution every 0.1 seconds
o fixes for windows cross compile (using mingw32)
o compile flags of -fPIE for android
o configure --enable-checkprograms to compile ancillary binaries used to test things such as delay, isoch, pdf generation
o compile tests when trying to use 64b seq numbers on a 32b platform
o Fix GCC ver 8 warnings

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
6 years agobrcm63xx: switch to 4.14
Jonas Gorski [Wed, 1 Aug 2018 10:18:13 +0000 (12:18 +0200)]
brcm63xx: switch to 4.14

Kernel 4.14 support has been present for quite some time, so let's give
it wider testing.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
6 years agobrcm63xx: drop b43 from devices with unsupported wifi
Jonas Gorski [Wed, 1 Aug 2018 10:14:39 +0000 (12:14 +0200)]
brcm63xx: drop b43 from devices with unsupported wifi

The internal wifi isn't supported, so drop b43 from devices that only
have it.

Fixes FS#1698
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
6 years agobrcm63xx: copy SR102 support patch to 4.14 as well
Jonas Gorski [Wed, 1 Aug 2018 10:04:39 +0000 (12:04 +0200)]
brcm63xx: copy SR102 support patch to 4.14 as well

It seems to have been missed when the patch was accepted.

Fixes: d59126040701 ("brcm63xx: initial support for Sky SR102 router")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
6 years agobrcm63xx: drop bogus SPROM section from SR102
Jonas Gorski [Wed, 1 Aug 2018 09:39:57 +0000 (11:39 +0200)]
brcm63xx: drop bogus SPROM section from SR102

The integrated SoC wifi will likely never be supported, and if,
it will go through DT with the sprom contents there.

Fixes: d59126040701 ("brcm63xx: initial support for Sky SR102 router")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
6 years agobase-files: fix HOME_URL replace
Chen Minqiang [Thu, 2 Aug 2018 01:10:15 +0000 (09:10 +0800)]
base-files: fix HOME_URL replace

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
6 years agoar71xx: add support for TP-LINK CPE510 V2.0
Andrew Cameron [Wed, 27 Jun 2018 03:09:03 +0000 (22:09 -0500)]
ar71xx: add support for TP-LINK CPE510 V2.0

Adds Support for the TP-LINK CPE510 V2.0 by TP-Link.
The hardware is almost the same as the CPE510 V1.0
Follow the same processes as for the CPE510 V1.0

Signed-off-by: Andrew Cameron <apcameron@softhome.net>
6 years agoRevert "ar71xx: ag71xx: Prevent kernel oops for board def"
Jo-Philipp Wich [Wed, 1 Aug 2018 20:33:49 +0000 (22:33 +0200)]
Revert "ar71xx: ag71xx: Prevent kernel oops for board def"

This reverts commit 7a3e133751870a3431e2430386a77a002eb24117.

This change reportedly breaks connectivity on some ar71xx devices, so
revert it for now.

Ref: https://github.com/openwrt/openwrt/pull/1217#issuecomment-409708087
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6 years agoRevert "ar71xx: ag71xx: Add connect message: fixed phy"
Jo-Philipp Wich [Wed, 1 Aug 2018 20:31:34 +0000 (22:31 +0200)]
Revert "ar71xx: ag71xx: Add connect message: fixed phy"

This reverts commit 0b9f4e880807e3cfd22d12b929202e1edcdc577c.

This change reportedly breaks connectivity on some ar71xx devices, so
revert it for now.

Ref: https://github.com/openwrt/openwrt/pull/1217#issuecomment-409708087
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6 years agoRevert "ar71xx: ag71xx_phy: Fix compilation for debug messages"
Jo-Philipp Wich [Wed, 1 Aug 2018 20:31:04 +0000 (22:31 +0200)]
Revert "ar71xx: ag71xx_phy: Fix compilation for debug messages"

This reverts commit 2655fbe8efb2a596aa8db92cffa817e3bf0c64ea.

The patch introduces syntax errors, revert it for now.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6 years agogdb: bump to 8.1.1
Koen Vandeputte [Wed, 1 Aug 2018 11:32:22 +0000 (13:32 +0200)]
gdb: bump to 8.1.1

GDB 8.1.1 brings the following fixes and enhancements over GDB 8.1:

 * PR gdb/22824 (misleading description of new rbreak Python function in GDB 8.1 NEWS file)
 * PR gdb/22849 (ctrl-c doesn't work in extended-remote)
 * PR gdb/22907 ([Regression] gdbserver doesn't work with filename-only binaries)
 * PR gdb/23028 (inconsistent disassemble of vcvtpd2dq)
 * PR gdb/23053 (Fix -D_GLIBCXX_DEBUG gdb-add-index regression)
 * PR gdb/23127 ([AArch64] GDB cannot be used for debugging software that uses high Virtual Addresses)
 * PR server/23158 (gdbserver no longer functional on Windows)
 * PR breakpoints/23210 ([8.1/8.2 Regression] Bogus Breakpoint address adjusted from 0xf7fe7dd3 to 0xfffffffff7fe7dd3)

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
6 years agotoolchain/gdb: bump to 8.1.1
Koen Vandeputte [Wed, 1 Aug 2018 11:39:03 +0000 (13:39 +0200)]
toolchain/gdb: bump to 8.1.1

GDB 8.1.1 brings the following fixes and enhancements over GDB 8.1:

 * PR gdb/22824 (misleading description of new rbreak Python function in GDB 8.1 NEWS file)
 * PR gdb/22849 (ctrl-c doesn't work in extended-remote)
 * PR gdb/22907 ([Regression] gdbserver doesn't work with filename-only binaries)
 * PR gdb/23028 (inconsistent disassemble of vcvtpd2dq)
 * PR gdb/23053 (Fix -D_GLIBCXX_DEBUG gdb-add-index regression)
 * PR gdb/23127 ([AArch64] GDB cannot be used for debugging software that uses high Virtual Addresses)
 * PR server/23158 (gdbserver no longer functional on Windows)
 * PR breakpoints/23210 ([8.1/8.2 Regression] Bogus Breakpoint address adjusted from 0xf7fe7dd3 to 0xfffffffff7fe7dd3)

GDB 8.1 includes the following changes and enhancements:

  * Breakpoints on C++ functions are now set on all scopes by default
    ("wild" matching);

  * Support for inserting breakpoints on functions marked with C++ ABI tags;

  * Target floating-point arithmetic emulation during expression evaluation
    (requires MPFR 3.1 or later);

  * Various Python Scripting enhancements;

  * Improved Rust support; in particular, Trait objects can now be inspected
    when debugging Rust code;

  * GDB no longer makes assumptions about the type of symbols without
    debugging information to avoid producing erroneous and often confusing
    results;

  * The 'enable' and 'disable' commands now accept a range of breakpoint
    locations;

  * New 'starti' command to start the program at the first instruction;

  * New 'rbreak' command to insert a number of breakpoints via a regular
    expression pattern (requires Python);

  * The 'ptype' command now supports printing the offset and size of
    the fields in a struct;

  * The 'gcore' command now supports dumping all the memory mappings
    ('-a' command-line option);

  * New shortcuts for TUI Single-Key mode: 'i' for stepi, and 'o' for nexti;

  * GDBserver enhancements:
    ** Support for transmitting environment variables to GDBserver;
    ** Support for starting inferior processes with a specified initial
       working directory;
    ** On Unix systems, support for globbing expansion and variable
       substitution of inferior command-line arguments;

  * Various completion enhancements;

  * The command used to compile and inject code with the 'compile' command
    is now configurable;

  * New '--readnever' command-line option to speed the GDB startup when
    debugging information is not needed;

  * Support for the following new native configurations:
    ** FreeBSD/aarch64 (aarch64*-*-freebsd*);
    ** FreeBSD/arm (arm*-*-freebsd*);

  * Support for the following new targets:
    ** FreeBSD/aarch64 (aarch64*-*-freebsd*);
    ** FreeBSD/arm (arm*-*-freebsd*);
    ** OpenRISC ELF (or1k*-*-elf)

  * Removed support for the following targets and native configurations:
    ** Solaris2/x86 (i?86-*-solaris2.[0-9]);
    ** Solaris2/sparc (sparc*-*-solaris2.[0-9]);

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
6 years agoadb: added patch for openssl 1.1.0 compatibility
Eneas U de Queiroz [Fri, 25 May 2018 14:43:32 +0000 (11:43 -0300)]
adb: added patch for openssl 1.1.0 compatibility

Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
6 years agonftables: allow to build with json support
Rosy Song [Tue, 31 Jul 2018 09:09:34 +0000 (17:09 +0800)]
nftables: allow to build with json support

Signed-off-by: Rosy Song <rosysong@rosinson.com>
6 years agoar71xx: cr3000: cleanup board definition
Daniel F. Dickinson [Sun, 29 Jul 2018 11:40:01 +0000 (07:40 -0400)]
ar71xx: cr3000: cleanup board definition

1) Add comments so it's clear why we did things; this may prevent
   someone (e.g. me) from sinking time into fixing things that
   aren't broken and/or were done for reason.

2) Drop mdio 0 probe/register; we don't use ag1xx mdio bus 0.

3) Cosmetic reording of some code (tested) that makes the defintion
   more clear.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
6 years agoar71xx: cr3000: Use correct company name
Daniel F. Dickinson [Sun, 29 Jul 2018 11:17:19 +0000 (07:17 -0400)]
ar71xx: cr3000: Use correct company name

It's 'PowerCloud Systems' not 'PowerCloud'.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
6 years agoar71xx: cr3000: Drop support for defunct cloud
Daniel F. Dickinson [Wed, 25 Jul 2018 23:18:07 +0000 (19:18 -0400)]
ar71xx: cr3000: Drop support for defunct cloud

The CR3000 stock firmware is now irrelevant as it required a now defunct
cloud service.  Therefore only build images that use the entire flash
(overwriting stock firwmare-specific partitions that no longer matter),
previously called 'nocloud' images.

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
6 years agoath79: Forward port support for CR3000
Daniel F. Dickinson [Sat, 28 Jul 2018 12:57:22 +0000 (08:57 -0400)]
ath79: Forward port support for CR3000

The PowerCloud Systems CR3000 was a cloud-managed CPE for a now defunct
NaaS offering.  It was previously supported under the ar71xx branch and
this forward ports that support with some notable differences:

1) Since reverting to stock firmware is now irrelevant there is is only
a single openwrt image generated which uses the entire flash rather than
preserving PowerCloud-specific partitions that are unneeded to openwrt--
those partitions will be erased and used by the openwrt image.

2) Rather than use a non-standard probe order for the ethernet devices,
this image uses a set of 'ip link set ethX name ethY' commands very early
in preinit (before the network is used at all), in order to have the the
switch and Wan use the same ethernet names as in previous images.

3) /etc/config/wireless will need to be regenerated as the path to the
wireless device has changed due to differences in ath79 DT for ar93x
compared to ar71xx images.

4) eth0 is wan and eth1 is lan (switch)

Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
6 years agokernel: bump 4.9 to 4.9.116
Koen Vandeputte [Tue, 31 Jul 2018 11:30:14 +0000 (13:30 +0200)]
kernel: bump 4.9 to 4.9.116

Refreshed all patches

Remove upstreamed patches.
- 103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch
- 403-mtd_fix_cfi_cmdset_0002_status_check.patch
- 001-4.11-01-mtd-m25p80-consider-max-message-size-in-m25p80_read.patch
- 001-4.15-08-bcm63xx_enet-correct-clock-usage.patch
- 001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch
- 900-gen_stats-fix-netlink-stats-padding.patch

Introduce a new backported patch to address ext4 breakage, introduced in 4.9.112
- backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch

This patch has been slightly altered to compensate for a new helper function
introduced in later kernels.

Also add ARM64_SSBD symbol to ARM64 targets still running kernel 4.9

Compile-tested on: ar71xx, bcm2710
Runtime-tested on: ar71xx

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
6 years agosdk: bundle usbip userspace sources
Jo-Philipp Wich [Wed, 1 Aug 2018 07:11:17 +0000 (09:11 +0200)]
sdk: bundle usbip userspace sources

Bundle the usbip utility sources shipped with the Linux kernel tree in
order to allow the usbip packages from the package feed to build within
the OpenWrt SDK.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6 years agoiwinfo: update to latest Git HEAD
Jo-Philipp Wich [Tue, 31 Jul 2018 18:39:13 +0000 (20:39 +0200)]
iwinfo: update to latest Git HEAD

a514139 build: compile with -ffunction-sections, -fdata-sections and LTO
3c30b17 wl: only invoke nvram executable if it exists
65b8333 Revert "build: compile with -ffunction-sections, -fdata-sections and LTO"

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6 years agoinclude/feeds.mk: fix distfeeds.conf without per-feed repos
Bjørn Mork [Tue, 31 Jul 2018 12:01:12 +0000 (14:01 +0200)]
include/feeds.mk: fix distfeeds.conf without per-feed repos

commit 514a4b3e1b4e4 ("include/feeds.mk: rework generation of opkg
distfeeds.conf") made the per-feed "base" repo unconditional, making
the default configuration fail when PER_FEED_REPO is disabled:

 root@wrt1900ac-1:~# cat /etc/opkg/distfeeds.conf
 src/gz openwrt_core http://openwrt.mork.no/18.06.0/targets/mvebu/cortexa9/packages
 src/gz openwrt_base http://openwrt.mork.no/18.06.0/packages/arm_cortex-a9_vfpv3/base
 root@wrt1900ac-1:~# opkg update
 Downloading http://openwrt.mork.no/18.06.0/targets/mvebu/cortexa9/packages/Packages.gz
 Updated list of available packages in /var/opkg-lists/openwrt_core
 Downloading http://openwrt.mork.no/18.06.0/targets/mvebu/cortexa9/packages/Packages.sig
 Signature check passed.
 Downloading http://openwrt.mork.no/18.06.0/packages/arm_cortex-a9_vfpv3/base/Packages.gz
 *** Failed to download the package list from http://openwrt.mork.no/18.06.0/packages/arm_cortex-a9_vfpv3/base/Packages.gz

 Collected errors:
  * opkg_download: Failed to download http://openwrt.mork.no/18.06.0/packages/arm_cortex-a9_vfpv3/base/Packages.gz, wget returned 8.

Cc: Matthias Schiffer <mschiffer@universe-factory.net>
Fixes: 514a4b3e1b4e ("include/feeds.mk: rework generation of opkg distfeeds.conf")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
[whitespace/indentation fix]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6 years agokernel: add missing ARM64_SSBD symbol
Stijn Tintel [Tue, 31 Jul 2018 09:19:18 +0000 (12:19 +0300)]
kernel: add missing ARM64_SSBD symbol

In 4.14.57, a new symbol for Spectre v4 mitigation was introduced for
ARM64. Add this symbol to all ARM64 targets using kernel 4.14.

This mitigates CVE-2018-3639 on ARM64.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
6 years agomac80211: brcmfmac: backport patch for per-firmware features
Rafał Miłecki [Tue, 31 Jul 2018 07:44:19 +0000 (09:44 +0200)]
mac80211: brcmfmac: backport patch for per-firmware features

This allows driver to support features that can't be dynamically
discovered.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
6 years agokernel: remove duplicate #define's in at803x Ethernet PHY driver
Daniel Golle [Tue, 31 Jul 2018 03:17:52 +0000 (05:17 +0200)]
kernel: remove duplicate #define's in at803x Ethernet PHY driver

AT803X_REG_CHIP_CONFIG and AT803X_BT_BX_REG_SEL have been defined
upstream by commit f62265b53ef3 ("at803x: double check SGMII side autoneg")
An existing local patch then added those exact same defines again which
isn't necessary, so remove them.

Fixes: f791fb4af450 ("kernel: add linux 4.9 support")
Fixes: b3f95490b9be ("kernel: generic: Add kernel 4.14 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6 years agokernel: re-add patch for AT8032 Ethernet PHY
Daniel Golle [Tue, 31 Jul 2018 02:50:38 +0000 (04:50 +0200)]
kernel: re-add patch for AT8032 Ethernet PHY

The patch was wrongly removed by a kernel version bump to 4.9.105 in
the believe that it was merged upstream thow it wasn't. This lead to
unrecoverable link losses on devices which use those PHYs such as
many ubnt single-port CPEs.

Fixes: 7dca1bae82 (kernel: bump to 4.9.105)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
6 years agokernel: add pending e1000e fixes
Stijn Tintel [Thu, 28 Jun 2018 09:44:10 +0000 (11:44 +0200)]
kernel: add pending e1000e fixes

The previous round of fixes for the 82574 chip cause an issue with
emulated e1000e devices in VMware ESXi 6.5. It also contains changes
that are not strictly necessary. These patches fix the issues introduced
in the previous series, revert the unnecessary changes to avoid
unforeseen fallout, and avoid a case where interrupts can be missed.

The final two patches of this series are already in the kernel, so no
need to include them here.

Patchwork: https://patchwork.ozlabs.org/cover/881776/

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
6 years agokernel: bump 4.14 to 4.14.59
Stijn Tintel [Tue, 31 Jul 2018 02:11:07 +0000 (05:11 +0300)]
kernel: bump 4.14 to 4.14.59

Drop patch that was superseded upstream:
ramips/0036-mtd-fix-cfi-cmdset-0002-erase-status-check.patch

Drop upstreamed patches:
- apm821xx/020-0001-crypto-crypto4xx-remove-bad-list_del.patch
- apm821xx/020-0011-crypto-crypto4xx-fix-crypto4xx_build_pdr-crypto4xx_b.patch
- ath79/0011-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch
- brcm63xx/001-4.15-08-bcm63xx_enet-correct-clock-usage.patch
- brcm63xx/001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch
- generic/backport/080-net-convert-sock.sk_wmem_alloc-from-atomic_t-to-refc.patch
- generic/pending/170-usb-dwc2-Fix-DMA-alignment-to-start-at-allocated-boun.patch
- generic/pending/900-gen_stats-fix-netlink-stats-padding.patch

In 4.14.55, a patch was introduced that breaks ext4 images in some
cases. The newly introduced patch
backport-4.14/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch
addresses this breakage.

Fixes the following CVEs:
- CVE-2018-10876
- CVE-2018-10877
- CVE-2018-10879
- CVE-2018-10880
- CVE-2018-10881
- CVE-2018-10882
- CVE-2018-10883

Compile-tested: ath79, octeon, x86/64
Runtime-tested: ath79, octeon, x86/64

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
6 years agoca-caertificates: remove myself as PKG_MAINTAINER
Christian Schoenebeck [Mon, 30 Jul 2018 19:28:00 +0000 (21:28 +0200)]
ca-caertificates: remove myself as PKG_MAINTAINER

remove myself as PKG_MAINTAINER

Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
6 years agonetifd: update to latest git HEAD
John Crispin [Mon, 30 Jul 2018 21:56:14 +0000 (23:56 +0200)]
netifd: update to latest git HEAD

fix a compile error

Signed-off-by: John Crispin <john@phrozen.org>
6 years agokernel: switch compatible property for RedBoot DT binding
Matt Merhar [Mon, 30 Jul 2018 21:21:57 +0000 (17:21 -0400)]
kernel: switch compatible property for RedBoot DT binding

This changes the DT binding's compatible property to
"ecoscentric,redboot-fis-partitions", removing the existing reference to
Red Hat.

Per the documentation hosted at eCosCentric's website, eCosCentric is
RedBoot's sole commercial maintainer since 2002, and the project has
been under the stewardship of the Free Software Foundation since 2008.

This also updates the property in the Inventel Livebox 1 .dts, the
binding's only current user.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
6 years agonetifd: update to latest git HEAD (FS#1668)
Hans Dedecker [Mon, 30 Jul 2018 20:54:04 +0000 (22:54 +0200)]
netifd: update to latest git HEAD (FS#1668)

75ee790 interface-ip: fix eui64 ifaceid generation (FS#1668)
ca97097 netifd: make sure the vlan ifname fits into the buffer
b8c1bca iprule: remove bogus assert calls
a2f952d iprule: fix broken in_dev/out_dev checks
263631a vlan: use alloca to get rid of IFNAMSIZE in vlan_dev_set_name()
291ccbb ubus: display correct prefix size for IPv6 prefix address
908a9f4 CMakeLists.txt: add -Wimplicit-fallthrough to the compiler flags
b06b011 proto-shell.c: add a explicit "fall through" comment to make the compiler happy
60293a7 replace fall throughs in switch/cases where possible with simple code changes

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
6 years agokernel: modules: fix kmod-regmap
Christian Lamparter [Mon, 30 Jul 2018 20:33:51 +0000 (22:33 +0200)]
kernel: modules: fix kmod-regmap

This patch fixes the a compile issue that was triggered by
apm821xx/sata when kmod-regmap was selected.

The CONFIG_REGMAP is declared in drivers/base/regmap/Kconfig
as type "bool" and not "tristate". Hence the symbol should
never be set to module, as this confuses the #if CONFIG_REGMAP
guards in include/linux/regmap.h:

|.../drivers/regulator/core.c:4041: undefined reference to `dev_get_regmap'
|.../drivers/regulator/core.c:4042: undefined reference to `dev_get_regmap'
|.../drivers/regulator/core.c:4044: undefined reference to `dev_get_regmap'
|.../drivers/regulator/helpers.o: In function `regulator_is_enabled_regmap':
|.../drivers/regulator/helpers.c:36: undefined reference to `regmap_read'
|...

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
6 years agotcpdump: explicitly disable libcap-ng support
Stijn Tintel [Mon, 30 Jul 2018 20:23:48 +0000 (23:23 +0300)]
tcpdump: explicitly disable libcap-ng support

When libcap-ng is detected during build, support for it is enabled. This
will cause a build failure due to a missing dependency. Explicitly
disable libcap-ng support to avoid this.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
6 years agobrcm2708: fix w1 patch
John Crispin [Mon, 30 Jul 2018 18:51:56 +0000 (20:51 +0200)]
brcm2708: fix w1 patch

this is now part of generic

Signed-off-by: John Crispin <john@phrozen.org>
6 years agoipq40xx: Limit usable channels for OpenMesh A62 PHYs
Sven Eckelmann [Mon, 30 Jul 2018 15:43:48 +0000 (17:43 +0200)]
ipq40xx: Limit usable channels for OpenMesh A62 PHYs

The OpenMesh A62 is a tri-band device (1x 2.4GHz, 2x 5GHz) with special
filters in front of the RX+TX paths to the 5GHz PHYs. These filtered
channel can in theory still be used by the hardware but the signal strength
is reduced so much that it makes no sense.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
6 years agomac80211: ath10k: Limit available channels via DT ieee80211-freq-limit
Sven Eckelmann [Mon, 30 Jul 2018 15:43:09 +0000 (17:43 +0200)]
mac80211: ath10k: Limit available channels via DT ieee80211-freq-limit

Tri-band devices (1x 2.4GHz + 2x 5GHz) often incorporate special filters in
the RX and TX path. These filtered channel can in theory still be used by
the hardware but the signal strength is reduced so much that it makes no
sense.

There is already a DT property to limit the available channels but ath10k
has to manually call this functionality to limit the currrently set wiphy
channels further.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
6 years agoath79: fix irq assignment for pci-ar71xx driver
Matt Merhar [Mon, 30 Jul 2018 18:11:09 +0000 (14:11 -0400)]
ath79: fix irq assignment for pci-ar71xx driver

In the new DT-based pci-ar71xx driver, ar71xx_pci_irq_init() was being
called before populating the PCI controller's device_node struct member.
This led to no IRQ being assigned to connected PCI devices (e.g. ath9k
cards) and caused them to be non-functional aside from simply being
detected.

The previous errors encountered in dmesg were: "irq: no irq domain found
for /ahb/apb/pcie-controller@180c0000 !". /proc/interrupts listed an IRQ
of 0 for the cards.

While this has been only been tested on a yet-to-be-merged RouterStation
Pro target, it should also fix the broken wifi people have reported for
the ath79 WNDR3800 target.

Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
6 years agokernel: add kmod-iio-htu21
Torbjörn Jansson [Mon, 30 Jul 2018 13:59:20 +0000 (15:59 +0200)]
kernel: add kmod-iio-htu21

This adds support for the htu21 humidity and temperature sensor.

To get it to work you have to do something like this:
echo "htu21 0x40" >/sys/class/i2c-dev/i2c-1/device/new_device
for example by adding it to rc.local

Compile tested on brcm2708 and I have used an earlier version of this
patch for more than a year.

Signed-off-by: Torbjörn Jansson <torbjorn.jansson@mbox200.swipnet.se>
6 years agowolfssl: remove myself as maintainer
Alexandru Ardelean [Mon, 30 Jul 2018 14:03:18 +0000 (17:03 +0300)]
wolfssl: remove myself as maintainer

I no longer have the time, nor the desire to maintain this package.
Remove myself as maintainer.

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
6 years agoar71xx: define switch for rb-952ui-5ac2nd
Thibaut VARÈNE [Mon, 30 Jul 2018 15:37:40 +0000 (17:37 +0200)]
ar71xx: define switch for rb-952ui-5ac2nd

QCA9533 built-in switch can be configured

Tested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
6 years agoipq40xx: fix booting secondary CPU cores
Mantas Pucka [Mon, 30 Jul 2018 15:08:49 +0000 (18:08 +0300)]
ipq40xx: fix booting secondary CPU cores

95672e04 broke booting secondary cores by removing 'qcom,saw' property
from L2 cache node. kpssv2_release_secondary() requires it.

Signed-off-by: Mantas Pucka <mantas@8devices.com>
6 years agoar71xx: fix TL-WR1043N v5 port mapping
John Crispin [Mon, 30 Jul 2018 15:47:06 +0000 (17:47 +0200)]
ar71xx: fix TL-WR1043N v5 port mapping

fixes 5660c8fb20 ("ar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.")

Signed-off-by: John Crispin <john@phrozen.org>
6 years agobase-files: drop fwtool_pre_upgrade
John Crispin [Mon, 30 Jul 2018 15:42:39 +0000 (17:42 +0200)]
base-files: drop fwtool_pre_upgrade

this feature has never worked, the fw image name was not passed and the -t
parameter was missing in the tool invocation. drop the feature.

Signed-off-by: John Crispin <john@phrozen.org>
6 years agoar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.
Tim Thorpe [Wed, 18 Apr 2018 22:50:05 +0000 (17:50 -0500)]
ar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.

Reversed the numbering of the LAN ports in Luci so as to match the port numbers on the housing.

Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
6 years agoar71xx: TL-WR1043N v4/v5: add orange WAN LED support
Tim Thorpe [Tue, 13 Feb 2018 15:26:18 +0000 (09:26 -0600)]
ar71xx: TL-WR1043N v4/v5: add orange WAN LED support

Add missing definitions for the orange WAN LED on the
TL-WR1043N(D) v4 and v5.

Change the name of a MAC address offset constant to
make it consistent with the format of the
existing constants.

Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
6 years agoath79: add support for tl-wr841n-v9
Lucian Cristian [Mon, 30 Jul 2018 13:21:12 +0000 (16:21 +0300)]
ath79: add support for tl-wr841n-v9

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
6 years agoramips: add support for ELECOM WRC-2533GST
INAGAKI Hiroshi [Thu, 26 Jul 2018 14:24:22 +0000 (23:24 +0900)]
ramips: add support for ELECOM WRC-2533GST

ELECOM WRC-2533GST is a 2.4/5 GHz band 11ac rotuer, based on
MediaTek MT7621A.

Specification:

- MT7621A (2-Core, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 4T4R 2.4/5 GHz wifi
  - MediaTek MT7615
- 5x 10/100/1000 Mbps Ethernet
- 4x LEDs, 6 keys (2x buttons, 1x slide switch)
- UART header on PCB
  - Vcc, GND, TX, RX from ethernet port side
  - baudrate: 57600 bps

Flash instruction using factory image:

1. Connect the computer to the LAN port of WRC-2533GST
2. Connect power cable to WRC-2533GST and turn on it
3. Access to "https://192.168.2.1/" and open firmware update
page ("ファームウェア更新")
4. Select the OpenWrt factory image and click apply ("適用")
button
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
6 years agoimagebuilder: add function to show manifest
Paul Spooren [Fri, 20 Jul 2018 08:32:12 +0000 (17:32 +0900)]
imagebuilder: add function to show manifest

Tested with 18.06.0-rc2/ar71xx/generic/tl-wdr4300-v1, image & list

This PR is based on the work of @fewckert[1] with slight improvements.

Add function `manifest` to show the manifest of the produced image,
before actually building it. The manifest contains an orderd list of
package name and version.

This is usefull to check package dependencies but also determine a
unique and reproducible image name before building the package. The
sysupgrade server[2] builds images on request with individual package
selection. To distignish between created images which contain differnt
packages, the EXTRA_IMAGE_NAME is set to a shortend hash of the
manifest's content. So far the image was renamed afterwards as the
manifests content was unknown, however this corrupts the signed
sha256sums. This patch allows a clean solution as to dtermine the
manifest in advance and set the EXTRA_IMAGE_NAME accordingly.

[1]: https://github.com/lede-project/source/pull/1591
[2]: https://github.com/aparcar/attendedsysupgrade-server

Signed-off-by: Paul Spooren <mail@aparcar.org>
6 years agox86: add support to set GRUB menu entry title
Kjel Delaey [Tue, 5 Jun 2018 13:47:05 +0000 (15:47 +0200)]
x86: add support to set GRUB menu entry title

$ make menuconfig

        Target Images -> Title for the menu entry in GRUB

Signed-off-by: Kjel Delaey <kjel_delaey@hotmail.com>
6 years agokirkwood: add support for Iomega Storcenter ix2-200
Ademar Arvati Filho [Fri, 6 Jul 2018 00:56:58 +0000 (00:56 +0000)]
kirkwood: add support for Iomega Storcenter ix2-200

Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell
 Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of
 flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC

Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1000Mhz
- Flash-Chip: Hynix NAND
- Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16
- RAM: 256MB
- LAN: 1x 1000 Mbps Ethernet
- WiFi: none
- 3x USB 2.0
- UART: for serial console

Installation instructions - easy steps:
1. download factory.bin and copy into tftp server
2. access uboot environment with serial cable and run
    ```
    setenv mainlineLinux yes
    setenv arcNumber 1682
    setenv console 'console=ttyS0,115200n8'
    setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
    setenv bootargs_root 'root='
    setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
    saveenv
    setenv serverip 192.168.1.1
    setenv ipaddr 192.168.1.13
    tftpboot 0x00800000 factory.bin
    nand erase 0x100000 $(filesize)
    nand write 0x00800000 0x100000 $(filesize)
    run bootcmd
    ```
3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)

Installation steps nand bad blocks proof:
1. download initramfs-uImage and copy into usb ext2 partition
    ```
    mkfs.ext2 -L ext2 /dev/sdh1
    mount -t ext2 /dev/sdh1 /mnt
    cp initramfs-uImage /mnt/initramfs.bin
    umount /mnt
    ```
2. access uboot environment with serial cable and run
    ```
    setenv mainlineLinux yes
    setenv arcNumber 1682
    setenv console 'console=ttyS0,115200n8'
    setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
    setenv bootargs_root 'root='
    setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
    saveenv
    usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000
    ```
3. log into openwrt and sysupgrade to install into flash
    ```
    sysupgrade -n /tmp/sysupgrade.bin
    ```
4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)

Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
6 years agolibevent2: Don't build tests and samples
Eneas U de Queiroz [Mon, 30 Jul 2018 12:27:52 +0000 (12:27 +0000)]
libevent2: Don't build tests and samples

The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.

To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
This reduces build time significantly.

Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
6 years agoath10k-ct: fix build with current mac80211 package
Jo-Philipp Wich [Mon, 30 Jul 2018 13:00:53 +0000 (15:00 +0200)]
ath10k-ct: fix build with current mac80211 package

Commit 2dcd955aea ("mac80211: backport and update patches for ath10k")
changed the DFS detector API, causing ath10k-ct to fail building due to
a missing add_pulse() argument.

Extend the already existing kernel compatibility patch to also adjust
the add_pulse() call accordingly.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6 years agobuild: fix ASLR for LTO packages
Julien Dusser [Tue, 17 Jul 2018 16:29:34 +0000 (18:29 +0200)]
build: fix ASLR for LTO packages

Fix building packages with LTO when CONFIG_PKG_ASLR_PIE is enabled.

Despite comment of PR lto/80838, it seems that GCC needs -fPIC on linker
command line, even if all objects are -fPIC. This may change as PR
lto/80838 is merged into 8.1

compile-tested: ar71xx, ath79

Fix commits:
6dac92a42e052f89971762173daabb7fd84742ef
8c11133c9de632dca69c8464f911d8e2716effe2
07940acc341ee9bb2887359f193625e48f36207e
e7397eef69a20fc630148d0e597523e139d21c0c
ef16a394d2b24a363b50b5b4720cb23fe156c9da
ef96d1e34a990871c912938c336f51a510b1e32f
47b42137ce1e931ae5871952b1f98438396f5e07
73fc67b61480a3430d31de33478a1c0c2c364b9c
154c0c4006daf41e2cbb6c8b7ad5557f83dfea3e
804c51e1e661819c5a7532e66fb8a12166eef9a9

Signed-off-by: Julien Dusser <julien.dusser@free.fr>
6 years agosamsung/s5pv210: New target
Jianhui Zhao [Tue, 17 Apr 2018 03:09:14 +0000 (11:09 +0800)]
samsung/s5pv210: New target

Signed-off-by: Jianhui Zhao <jianhuizhao329@gmail.com>
6 years agoar71xx: add support for TP-Link Archer C59 v2
Keith Maika [Fri, 15 Jun 2018 04:39:09 +0000 (00:39 -0400)]
ar71xx: add support for TP-Link Archer C59 v2

TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB

Flash instruction:
  - via web UI:
    1. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
    2. Login to router and open the Advanced tab
    3. Navigate to System Tools -> Firmware Upgrade
    4. Upload firmware using the Manual Upgrade form
  - via TFTP:
    1. Set PC to fixed ip address 192.168.0.66
    2. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin
       and rename it to tp_recovery.bin
    3. Start a tftp server with the file tp_recovery.bin in its root directory
    4. Turn off the router
    5. Press and hold Reset button
    6. Turn on router with the reset button pressed and wait ~15 seconds
    7. Release the reset button and after a short time
       the firmware should be transferred from the tftp server
    8. Wait ~30 second to complete recovery.

Signed-off-by: Keith Maika <keithm@aoeex.com>
6 years agokernel: add missing include to redboot.c
Rafał Miłecki [Mon, 30 Jul 2018 10:06:20 +0000 (12:06 +0200)]
kernel: add missing include to redboot.c

This fixes:
drivers/mtd/redboot.c:299:34: error: array type has incomplete element type 'struct of_device_id'

Fixes: 5e8b4be53177 ("kernel: add DT binding support to the mtd redboot parser")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
6 years agobrcm63xx: update DT RedBoot binding for the Inventel Livebox 1
Rafał Miłecki [Mon, 30 Jul 2018 06:45:41 +0000 (08:45 +0200)]
brcm63xx: update DT RedBoot binding for the Inventel Livebox 1

linux,part-probe should be avoided as its only supported with OpenWrt
downstream patch that is going to be dropped eventually.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
6 years agobrcm47xx: rework model detection
Jo-Philipp Wich [Mon, 30 Jul 2018 06:36:26 +0000 (08:36 +0200)]
brcm47xx: rework model detection

On brcm47xx boards, the model ID is the combination of the "boardtype" nvram
variable and an optional supplemental "boardnum" variable while the human
readable model name is usually exposed in the "machine" field of the
/proc/cpuinfo file.

Move the extraction of the board nvram variables and model name string into
the 01_sysinfo file and rework the 01_detect board configuration script to
solely use the prepared sysinfo values without performing own detection
logic.

As a consequence, we can drop the ucidef_set_board_id() and
ucidef_set_model_name() invocations in favor to the generic behaviour
which copies the /tmp/sysinfo/{board_name,model} values into the board.json
"id" and "name" fields respectively.

Since "01_detect" only contains network configuration logic after this
change, move it to "01_network" and rename the contained "detect_by_xxx"
functions to "configure_by_xxx" instead, to avoid potential confusion.

Fixes FS#1576
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
6 years agoomap: disable ubifs
Lucian Cristian [Thu, 19 Jul 2018 06:59:43 +0000 (09:59 +0300)]
omap: disable ubifs

ubifs image are not working, until there is a fix, disable them

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
6 years agoomap: add support for f2fs/ext4 overlay creation
Lucian Cristian [Thu, 19 Jul 2018 06:58:42 +0000 (09:58 +0300)]
omap: add support for f2fs/ext4 overlay creation

add kernel support and include the tools for creating an overlay partition (f2fs or ext4)

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
6 years agoomap: add sysupgrade support
Lucian Cristian [Thu, 19 Jul 2018 06:55:19 +0000 (09:55 +0300)]
omap: add sysupgrade support

add sysupgrade missing script files

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
6 years agoomap: rename image for sysupgrade compatibility
Lucian Cristian [Thu, 19 Jul 2018 06:48:56 +0000 (09:48 +0300)]
omap: rename image for sysupgrade compatibility

for sysupgrade to work we need to change the image name based on dts target name

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
6 years agoomap: fix squashfs image boot and creation
Lucian Cristian [Thu, 19 Jul 2018 06:45:25 +0000 (09:45 +0300)]
omap: fix squashfs image boot and creation

fixes FS#1034, squash fs images fails to boot because of missing ARM BCJ filter decoder
also activate squashf image creation

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
6 years agohostapd: add ht and vht support in handle event function Add ht and vht capabilities...
Nick Hainke [Thu, 17 May 2018 10:35:23 +0000 (12:35 +0200)]
hostapd: add ht and vht support in handle event function Add ht and vht capabilities. If a device sends a probe request, the capabilities are added.

Signed-off-by: Nick Hainke <vincent@systemli.org>
6 years agohostapd: add ubus call for ap features
Nick Hainke [Wed, 25 Apr 2018 22:03:05 +0000 (00:03 +0200)]
hostapd: add ubus call for ap features

The call "get_features" allows to gather hostapd config options
via ubus. As first infos we add the ht and vht support.
Although nl80211 supports to gather informations about
ht and vht capabilities, the hostapd configuration can disable
vht and ht. However, it is possible that the iw output is not
representing the actual hostapd configuration.

Signed-off-by: Nick Hainke <vincent@systemli.org>