Kristian Evensen [Sun, 20 Oct 2019 09:33:13 +0000 (11:33 +0200)]
ipq40xx: Add support for Unielec U4019
This commit adds support for the 32MB storage/512MB RAM version of the U4019
IPQ4019-based board from Unielec. The board has the following specifications:
* Qualcomm IPQ4019 (running at 717MHz)
* 512MB DDR3 RAM (optional 256MB/1GB)
* 32MB SPI NOR (optional 8/16MB or NAND)
* Five gigabit ports (Qualcomm QCA8075)
* 1x 2.4 GHz wifi (QCA4019 hw1.0)
* 1x 5 Ghz wifi (QCA4019 hw1.0)
* 1x mini-PCIe slot (only USB-pins connected)
* 1x SIM slot (mini-SIM)
* 1x USB2.0 port
* 1x button
* 1x controllable LED
* 1x micro SD-card reader
Working:
* Ethernet
* Wifi
* USB-port
* mini-PCIe slot + SIM slot
* Button
* Sysupgrade
Not working:
* SD card slot (no upstream support)
Installation instructions:
In order to install OpenWRT on the U4019, you need to go via the
initramfs-image. The installation steps are as follows:
* Connect to board via serial (header exposed and clearly marked).
* Interrupt bootloader by pressing a button.
* Copy the initramfs-image to your tftp folder, call the file
C0A80079.img.
* Give the network interface connected to the U4019 the address
192.168.0.156/24.
* Start your tftp-server and run tftpboot on the board.
* Run bootm when the file has been transferred, to boot OpenWRT.
* Once OpenWRT has booted, copy the sysupgrade-image to the device and run
sysupgrade to install OpenWRT on the U4019.
Notes:
- Since IPQ4019 has been moved to 4.19, I have not added support for kernel
4.14.
- There is a bug with hardware encryption on IPQ4019, causing poor performance
with TCP and ipsec (see for example FS#2355). In order to improve performance,
I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if
bug is fixed.
- In order for Ethernet to work, the phy has to be reset by setting gpio 47
low/high. Adding support for phy reset via gpio required patching the
mdio-driver, and the code added comes from the vendor driver. I do not know if
patching the driver is an acceptable approach or not.
v1->v2:
* Do not use wildcard as identifier in the board.d-scripts (thanks
Adrian Schmutzler).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Daniel Gimpelevich [Thu, 17 Oct 2019 10:42:52 +0000 (03:42 -0700)]
ath79: fix gigabit link pll-data for EX7300
The device did not appear to be reachable unless the connection were
forced to 100Mb or lower. Revert to previously working pll-data.
Also fix the phy-mode to represent the actual state needed for ethernet
to function.
Reported-by: Moritz Schreiber <moritz@mosos.de>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[add remark about phy-mode property]
Signed-off-by: David Bauer <mail@david-bauer.net>
Yousong Zhou [Fri, 18 Oct 2019 12:10:06 +0000 (12:10 +0000)]
libpcap: build with cmake
The main motivation is to drop and stop maintaining
"100-debian_shared_lib.patch". It lacks the logic to include custom
implementation of several functions like pcap_strlcpy() which can cause
build failures when glibc is used [2]
CAN and CAN-USB support related symbols are now handled by general linux
support, see [1]
"-ffunction-sections -fdata-sections" were removed as they should help
much for shared libraries
Size comparison before and after the change
-rw-r--r-- 1 yunion yunion 238042 Oct 18 11:42 ipkg-x86_64/libpcap/usr/lib/libpcap.so.1
lrwxrwxrwx 1 yunion yunion 16 Oct 18 13:03 ipkg-x86_64/libpcap/usr/lib/libpcap.so.1 -> libpcap.so.1.9.1
-rwxr-xr-x 1 yunion yunion 229867 Oct 18 13:03 ipkg-x86_64/libpcap/usr/lib/libpcap.so.1.9.1
[1] On Linux, handle all CAN captures with pcap-linux.c, in cooked mode,
https://github.com/the-tcpdump-group/libpcap/commit/
93ca5ff7030aaf1219e1de05ec89a68384bfc50b
[2] https://github.com/openwrt/packages/issues/10270
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Michal Cieslakiewicz [Fri, 11 Oct 2019 08:50:11 +0000 (10:50 +0200)]
ath79: add AR934x NAND Flash Controller driver
This patch contains updated driver for Atheros NAND Flash Controller
written originally by Gabor Juhos for ar71xx (aka 'ar934x-nfc').
ath79 version has adapted to work with kernel 4.19 and Device Tree.
It has also been renamed to 'ar934x-nand' to avoid confusion with
Near-Field Communication technology.
Controller is present on Atheros AR934x SoCs and required for accessing
internal flash storage on routers like Netgear WNDR4300.
This port preserves all NAND programming code while moving platform
configuration to Device Tree and replacing some kernel functions marked
for retirement by 4.19.
Suitable definition is included in 'ar934x.dtsi' ('nand@
1b000200' section).
Most important changes to ar71xx version are:
* old kernel sections of code removed
* 'bool swap_dma' provided by platform data is now set by boolean DT
property 'qca,nand-swap-dma'
* board-supplied (mach-*.c code) platform data removed - its elements
become either unused, redundant or replaced by DT methods (like reset)
* IRQ is reserved by devm_request_irq() so free_irq() is not needed anymore
* calls to deprecated nand_scan_ident() + nand_scan_tail() function pair
replaced by using recommended nand_scan() with attach_chip() callback
* ECC is set to hardware by default, can be overriden by standard DT
'nand-ecc-*' properties (software Hamming or BCH are other options)
This driver has been successfully tested on Netgear WNDR4300 running
experimental ath79 OpenWrt master branch.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
[add reset control]
Signed-off-by: David Bauer <mail@david-bauer.net>
Masafumi UTSUGI [Tue, 1 Oct 2019 09:59:18 +0000 (18:59 +0900)]
ipq40xx: essedma: Fix dead lock
edma_read_append_stats() gets called from two places in the driver.
The first place is the kernel timer that periodically updates
the statistics, so nothing gets lost due to overflows.
The second one it's part of the userspace ethtool ioctl handler
to provide up-to-date values.
For this configuration, the use of spin_lock() is not sufficient
and as per:
<https://mirrors.edge.kernel.org/pub/linux/kernel/people/rusty/kernel-locking/c214.html>
the locking has to be upgraded to spin_lock_bh().
Signed-off-by: Masafumi UTSUGI <mutsugi@allied-telesis.co.jp>
[folded patch into 710-, rewrote message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Jeff Kletsky [Wed, 2 Oct 2019 19:06:18 +0000 (12:06 -0700)]
ath79: Clean up GL-AR300M DTS/DTSI inclusions
Modify GL-AR300M-Lite and GL-AR300M (NOR):
* Include qca9531_glinet_gl-ar300m.dtsi directly
rather than qca9531_glinet_gl-ar300m-nor.dts
* Remove redundant inclusion of gpio.h and input.h
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Eneas U de Queiroz [Tue, 1 Oct 2019 13:50:34 +0000 (10:50 -0300)]
openssl: Add engine configuration to openssl.cnf
This adds engine configuration sections to openssl.cnf, with a commented
list of engines. To enable an engine, all you have to do is uncomment
the engine line.
It also adds some useful comments to the devcrypto engine configuration
section. Other engines currently don't have configuration commands.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Josef Schlehofer [Sat, 19 Oct 2019 16:50:44 +0000 (18:50 +0200)]
strace: update to version 5.3
Makefile changes:
- moves PKG_MAINTAINER above PKG_LICENSE
- Change PKG_LICENSE to LGPL-2.1-or-later and correct PKG_LICENSE_FILES
- changes URL to a more appropriate one, which uses HTTPS
- adds 2 spaces as an indentation in description
Compile and run tested on Turris Omnia, mvebu
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Hauke Mehrtens [Sat, 19 Oct 2019 21:16:04 +0000 (23:16 +0200)]
kernel: Fix arm64 include files
This patch fixes the build of gdb and strace on arm64 targets with
kernel 4.19.
Without this patch asm/ptrace.h is including asm/sigcontext.h and this
file defines some structures which are also defined in musl header file
arch/aarch64/bits/signal.h. These two definitions then conflict with
each other and make the build fail.
This was seen locally and also by the build bot. The struct sigcontext,
struct sve_context and some others were defined twice. It looks like
this problem was introduced between 4.14 and 4.19 and it was fixed in
5.0. I already requested to backport this patch to kernel 4.19.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Moritz Warning [Wed, 25 Sep 2019 22:05:54 +0000 (00:05 +0200)]
ath25: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Moritz Warning [Mon, 9 Sep 2019 22:13:30 +0000 (00:13 +0200)]
mvebu: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Moritz Warning [Wed, 25 Sep 2019 21:56:13 +0000 (23:56 +0200)]
mediatek: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Moritz Warning [Wed, 25 Sep 2019 22:22:07 +0000 (00:22 +0200)]
octeon: split up remaining DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR and DEVICE_MODEL
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Moritz Warning [Mon, 9 Sep 2019 22:00:40 +0000 (00:00 +0200)]
at91: split up remaining DEVICE_TITLE definitions
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Moritz Warning [Tue, 15 Oct 2019 20:06:10 +0000 (22:06 +0200)]
rb532: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Ilya Gordeev [Sat, 12 Oct 2019 18:10:09 +0000 (23:10 +0500)]
tplink-safeloader: fix compilation warnings
Signed-off-by: Ilya Gordeev <Mirraz@users.noreply.github.com>
Biwen Li [Mon, 14 Oct 2019 04:42:32 +0000 (12:42 +0800)]
kernel: layerscape: fix compilation error
This fixes a compilation error as follows:
drivers/staging/fsl_qbman/qman_config.c:815:29: error: bitwise comparison
always evaluates to false [-Werror=tautological-compare]
if ((qman_ip_rev & 0xFF00) == QMAN_REV31) {
Signed-off-by: Biwen Li <biwen.li@nxp.com>
leo chung [Wed, 16 Oct 2019 04:22:55 +0000 (12:22 +0800)]
bzip2: add linker option LDFLAGS
if gcc not linker whith this LDFLAGS, "file libbz2.so.1.0.8" will
recognize as pie executable ELF file ( which should be shared object).
this because the file command version before 5.36 not recognize
correctly.
Signed-off-by: leo chung <gewalalb@gmail.com>
Mathew McBride [Thu, 3 Oct 2019 06:34:51 +0000 (16:34 +1000)]
kernel: add package for Epson RX-8025 and compatible I2C RTC
RX-8025 is an I2C RTC from Epson, some newer products such as the
RX-8035 are also compatible.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Hauke Mehrtens [Tue, 1 Oct 2019 21:28:36 +0000 (23:28 +0200)]
mac80211: Update to version 5.4-rc2
This updates mac80211 to backports based on kernel 5.4-rc2
ath10k-ct was updated to match the API changes and iw now uses the new
nl80211.h header file.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Fri, 11 Oct 2019 21:15:57 +0000 (23:15 +0200)]
mac80211: Update to version 5.3.6
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Christian Lamparter [Fri, 11 Oct 2019 20:53:14 +0000 (22:53 +0200)]
ipq806x: WPQ864: fix partition unit-address
This patch fixes what seems to be a simple copy & paste
error with the unit-address of the BOOTCONFIG partition.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Jo-Philipp Wich [Fri, 15 Mar 2019 18:23:31 +0000 (21:23 +0300)]
build: fix seq host tool check
Problem found on alpine linux when trying to `./scripts/feeds update -a`,
which results in `Build dependency: Missing seq command`.
Ref: https://github.com/openwrt/openwrt/pull/1926
Suggested-by: imShara <shara@protonmail.com>
[reworded commit and turned faulty Sob into Suggested-by]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Florian Eckert [Tue, 29 Aug 2017 09:10:48 +0000 (11:10 +0200)]
wwan: Double quote to prevent globbing and word splitting
Fix some shellcheck warnings.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
[bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Florian Eckert [Tue, 19 Dec 2017 10:37:51 +0000 (11:37 +0100)]
wwan: add ec25 to database
Add ec25 to database.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
[bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Florian Eckert [Tue, 29 Aug 2017 09:34:45 +0000 (11:34 +0200)]
wwan: add mc7304 to database
Add mc7304 to database.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
[bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Florian Eckert [Wed, 23 Aug 2017 05:23:52 +0000 (07:23 +0200)]
wwan: check new uci bus option on proto setup event
If system has more then one and different wwan interface (modem). Then the
wwan protohandler will always take the modem which is discovered first.
The protohandler will always setup the same interface. To fix this add a
new usb "bus" option which is associated with wwan device and so will set
the specified interface up. With this change more then one interface
could be mananged by the wwan protohandler.
If the "bus" option is not set in the uci network config then the protohandler
behaves as before the change. The protohanldler will take the first
interface which he founds.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Alin Nastac [Thu, 17 Oct 2019 12:06:40 +0000 (14:06 +0200)]
procd: allow usage of * as procd_running() instance parameter
service_running() implementation in /etc/rc.common use it.
It is preferable to use wildcard than assuming the instance
name is the default one.
jsonfilter returns all matches when wildcards are used, hence
the -l 1 argument used to limit output to only one value.
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Lucian Cristian [Tue, 15 Oct 2019 08:00:37 +0000 (11:00 +0300)]
util-linux: add more command
at least vtysh needs it for proper listing, busybox is not modular so add it here
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Sean Kenny [Thu, 15 Aug 2019 05:06:18 +0000 (23:06 -0600)]
6in4: add rfc1918 check function
This is a precursor to adding proper support for multiple
6in4 tunnels with the already programmed tunlink parameter.
This is an essential sanity check so as to not break existing
and working behind NAT setups.
Signed-off-by: Sean Kenny <skenny@wfap.ca>
6in4: add myip he.net api parameter logic
This is to add proper support for multiple 6in4 tunnels
with the already programmed tunlink parameter.
As it stands before this commit, if there is a multi wan setup that
consists of dynamic ips, there is no way to use the
dynamic update feature as the he.net api is implicitly using
the ip address of the caller. This will explicitly use the
ipaddr specified in the interface config OR the ip of the
tunlink interface specified in the dynamic update api call instead
ONLY if the final resolved ipaddr variable is not an rfc1918 address.
Signed-off-by: Sean Kenny <skenny@wfap.ca>
Alin Nastac [Mon, 7 Oct 2019 07:58:23 +0000 (09:58 +0200)]
lua: install luac symlink on host
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Christian Franke [Thu, 17 Oct 2019 13:12:05 +0000 (15:12 +0200)]
lantiq: Fix fw_cutter LzmaWrapper
The destination buffer size `d_len` is passed to `lzma_inflate` as a
pointer. Therefore, it needs to be dereferenced to compare its content.
Signed-off-by: Christian Franke <nobody@nowhere.ws>
Bjørn Mork [Thu, 17 Oct 2019 08:30:02 +0000 (10:30 +0200)]
kernel: fix MBIM description
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Jo-Philipp Wich [Thu, 17 Oct 2019 14:59:11 +0000 (16:59 +0200)]
fwtool: do not omit final 16 byte when image does not contain signature
The fwutil command will interpret the final 16 byte of a given firmware
image files as "struct fwimage_trailer".
In case these bytes do look like a valid trailer, we must ensure that we
print them out along with the remainder of the image to not accidentally
truncate non-trailer-images by 16 bytes when they're piped through fwtool,
e.g. as part of an image verification command sequence.
Some command sequences pipe images through fwtool in order to strip any
possible metadata, certificate or signature trailers and do not expect
bare images without any of that metadata to get truncated as other non-
fwtool specific metadata is expected at the end of the file, e.g. an
information block with an md5sum in case of the combined image format.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Paul Spooren [Sun, 13 Oct 2019 19:53:40 +0000 (09:53 -1000)]
build: add buildinfo as single Makefile target
The prepare target was added some 11 years ago to build tools and
toolchain and was recently extended to create buildinfo files for
reproducibility, meaning {feeds,version,config}.buildinfo.
As the buildbot workflow is more complex than the single prepare (kmod
feed insertion), prepare is only used to create those buildinfo files.
Running prepare however runs `target/compile` as well, taking time even
everything is already compiled.
Splitting this allows the buildbot to run only the `buildinfo` target
while others can still use the convenience feature `prepare`.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Kevin Darbyshire-Bryant [Sun, 13 Oct 2019 19:12:21 +0000 (20:12 +0100)]
wireguard: bump to latest snapshot
20191012
8eb8443 version: bump snapshot
be09cf5 wg-quick: android: use Binder for setting DNS on Android 10
4716f85 noise: recompare stamps after taking write lock
54db197 netlink: allow preventing creation of new peers when updating
f1b87d1 netns: add test for failing 5.3 FIB changes
a3539c4 qemu: bump default version
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kevin Darbyshire-Bryant [Sat, 12 Oct 2019 07:41:41 +0000 (08:41 +0100)]
toolchain/kernel-headers: don't use TARGET_CFLAGS
Kernel utilities (e.g. scripts/kconfig/conf) are being built to run on
the host system at this stage, therefore it makes no sense to use the
target system CC flags. Use HOSTCFLAGS instead
While we're here rename KMAKE macro to HOST_KMAKE to make it even more
obvious that we're building for host.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Jo-Philipp Wich [Wed, 16 Oct 2019 14:48:40 +0000 (16:48 +0200)]
iwinfo: update to latest Git HEAD
07315b6 nl80211: handle hidden SSIDs in wpa_supplicant scan results
3ac846e lua: fix string description of mixed WPA3 modes
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Adrian Schmutzler [Mon, 7 Oct 2019 15:08:52 +0000 (17:08 +0200)]
ramips: fix WiFi MAC addresses for D-Link DIR-810L
So far, WiFi MAC addresses for this device have been set up from
caldata. However, this returns values which do not look like MAC
addresses. They also do not match stock firmware:
wlan0 (5.0): 00:11:22:00:17:D0 from 0x8004
wlan1 (2.4): 00:11:22:00:17:CD from 0x4 (and 0x2e)
It looks like the only valid MAC address on this device is at 0x28.
So, this patch changes setup to calculate addresses based on the
value at 0x28:
lan: *:0A (flash, label)
wan: *:0B (flash + 1)
wifi2: *:0A (flash)
wifi5: *:0C (flash + 2)
Thanks to Roger Pueyo Centelles <roger.pueyo@guifi.net> for
investigating this on his devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Florian Eckert [Wed, 4 Sep 2019 08:00:48 +0000 (10:00 +0200)]
mac80211: add new acs_exclude_dfs option
The channel can be selected automatically at run time by setting
channel=acs_survey or channel=0, both of which will enable the ACS survey
based algorithm in hostapd. If the option acs_exclude_dfs is set in the
hostpad config DFS channels from ACS are excluded on channel selection.
This commit will add the possibilty to exclude the dfs channel on ACS
survey.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Martin Schiller [Mon, 23 Sep 2019 07:50:24 +0000 (09:50 +0200)]
lantiq: fix dsl_control status handling.
Commit
7519a36774ca ("base-files,procd: add generic service status")
introduced the generic 'status' command which broke the previous
dsl_control status output. To fix this, let's rename the "old" command
to "dslstat".
Fixes:
7519a36774ca ("base-files,procd: add generic service status")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Daniel Engberg [Sat, 23 Feb 2019 22:38:04 +0000 (22:38 +0000)]
libevent2: Update to 2.1.11
Update libevent to 2.1.11
Use CMake instead GNU Autotools
Backport following commits:
https://github.com/libevent/libevent/commit/
f05ba671931e2b4e38459899f6f63f79f99869fe
..and partially
https://github.com/libevent/libevent/commit/
7201062f3ef505a77baa6ccaf1cf73812462308a
to fix compilation
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Dan Haab [Tue, 15 Oct 2019 15:35:08 +0000 (09:35 -0600)]
bcm53xx: sysupgrade: support Luxul NAND devices
This adds support for UBI-aware sysupgrade using Luxul formats.
Signed-off-by: Dan Haab <dan.haab@legrand.com>
Michael Heimpold [Fri, 20 Sep 2019 22:15:24 +0000 (00:15 +0200)]
brcm47xx: fix switch port labels for Asus WL500GP V2
The switch port naming in LuCI does not fit the physical numbers
on the front of this device. Since this is confusing, fix it.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Rosen Penev [Tue, 15 Oct 2019 05:59:42 +0000 (22:59 -0700)]
lua: fix linking under glibc
Compilation of liblua itself works, but when other packages link against
it, the linker starts throwing undefined references to a bunch of math
functions in libm.
First discovered in a failed attempt to transition a package to uClibc++.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[fix commit title capitalization]
Signed-off-by: David Bauer <mail@david-bauer.net>
Adrian Schmutzler [Mon, 14 Oct 2019 12:02:40 +0000 (14:02 +0200)]
treewide: use a single ath10k MAC patching function with checksum
While all ath10k eeproms have a checksum field, so far two
functions for patching ath10k MAC address have been present (and
been used).
This merges code to provide a single function ath10k_patch_mac
in caldata.sh, having its name in accordance with ath9k functions.
By doing so, correct MAC patching for current and future ath10k
devices should be ensured.
This patch adds checksum adjustments for several targets on
ath79 and lantiq.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Mon, 7 Oct 2019 11:15:04 +0000 (13:15 +0200)]
ipq40xx: add label MAC address for FritzBox 4040
The CWMP-Account on the device's label contains the eth0 MAC
address.
This only changes 4.19 files as label-mac-device is introduced
after 19.07 branch, so there won't be a 4.14 release anymore.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
David Bauer [Mon, 14 Oct 2019 09:16:54 +0000 (11:16 +0200)]
ath79: correct ar71xx boardname for UniFi AC Lite
This corrects the additional boardname for the image metadata to the one
used in ar71xx. The previously present additional entry was never used
on a running system.
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sun, 13 Oct 2019 21:37:59 +0000 (23:37 +0200)]
mpc85xx: correct TP-LINK TL-WDR4900 MAC addresses
This commit fixes TP-Link TL-WDR4900 v1 MAC address assignment.
Previously, the MAC addrss was read for the ethernet from the "config"
partition. However, the content of this partition is dependent on the
firmware which was previously installed on the device.
Switch the MAC address source to the U-Boot partition, where the MAC
address is always present at a fixed partition. The partition was
previously already used for the WiFi MAC-addresses.
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
Andreas Ziegler [Sun, 6 Oct 2019 17:48:34 +0000 (19:48 +0200)]
ath79: add support for UniFi AC-LR
The Unifi AC-LR has identical hardware to the Unifi AC-Lite.
The antenna setup is different according to the vendor,
which explains the thicker enclosure.
Therefore, it is helpful to know the exact device variant,
instead of having "Ubiquiti UniFi-AC-LITE/LR".
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
[fix legacy name in commit message; add old boardname to
SUPPORTED_DEVICES]
Signed-off-by: David Bauer <mail@david-bauer.net>
Koen Vandeputte [Mon, 14 Oct 2019 15:37:28 +0000 (17:37 +0200)]
gdb: bump to 8.3.1
GDB 8.3.1 brings the following fixes and enhancements over GDB 8.3:
PR c++/20020 (GDB segfault on printing objects)
PR gdb/24454 (nat/x86-linux-dregs.c failed assertion)
PR breakpoints/24541 (Incorrect evaluation of systemtap probes due to register being signed and probe expression assuming unsigned)
PR symtab/24545 (Symbol loading performance regression with cc1)
PR gdb/24592 (amd64->i386 linux syscall restart problem)
PR gdb/25009 (terminate called after throwing an instance of 'srchilite::ParserException')
PR gdb/25010 (Calls to error () can cause SIGTTOU to send gdb to the background)
PR breakpoints/25011 (Breakpoints on file reloads broken for PIE binaries)
This corrective release also brings the following testsuite fixes and
enhancements:
PR testsuite/25005 (gdb-caching-proc.exp takes a lot of time on skip_opencl_tests)
PR testsuite/25016 (Test-case failures for -pie)
GDB 8.3 includes the following changes and enhancements:
* Support for new native configurations (also available as a target configuration):
- RISC-V GNU/Linux (riscv*-*-linux*)
- RISC-V FreeBSD (riscv*-*-freebsd*)
* Support for new target configurations:
- CSKY ELF (csky*-*-elf)
- CSKY GNU/Linux (csky*-*-linux)
- NXP S12Z ELF (s12z-*-elf)
- OpenRISC GNU/Linux (or1k*-*-linux*)
* Native Windows debugging is only supported on Windows XP or later.
* The Python API in GDB now requires Python 2.6 or later.
* GDB now supports terminal styling for the CLI and TUI.
Source highlighting is also supported by building GDB with GNU
Highlight.
* Experimental support for compilation and injection of C++ source
code into the inferior (requires GCC 7.1 or higher, built with
libcp1.so).
* GDB and GDBserver now support IPv6 connections.
* Target description support on RISC-V targets.
* Various enhancements to several commands:
- "frame", "select-frame" and "info frame" commands
- "info functions", "info types", "info variables"
- "info thread"
- "info proc"
- System call alias catchpoint support on FreeBSD
- "target remote" support for Unix Domain sockets.
* Support for displaying all files opened by a process
* DWARF index cache: GDB can now automatically save indices of DWARF
symbols on disk to speed up further loading of the same binaries.
* Various GDB/MI enhancements.
* GDBserver on PowerPC GNU/Linux now supports access to the PPR,
DSCR, TAR, EBB/PMU, and HTM registers.
* Ada task switching support when debugging programs built with
the Ravenscar profile added to aarch64-elf.
* GDB in batch mode now exits with status 1 if the last executed
command failed.
* Support for building GDB with GCC's Undefined Behavior Sanitizer.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 14 Oct 2019 14:09:08 +0000 (16:09 +0200)]
toolchain/gdb: bump to 8.3.1
GDB 8.3.1 brings the following fixes and enhancements over GDB 8.3:
PR c++/20020 (GDB segfault on printing objects)
PR gdb/24454 (nat/x86-linux-dregs.c failed assertion)
PR breakpoints/24541 (Incorrect evaluation of systemtap probes due to register being signed and probe expression assuming unsigned)
PR symtab/24545 (Symbol loading performance regression with cc1)
PR gdb/24592 (amd64->i386 linux syscall restart problem)
PR gdb/25009 (terminate called after throwing an instance of 'srchilite::ParserException')
PR gdb/25010 (Calls to error () can cause SIGTTOU to send gdb to the background)
PR breakpoints/25011 (Breakpoints on file reloads broken for PIE binaries)
This corrective release also brings the following testsuite fixes and
enhancements:
PR testsuite/25005 (gdb-caching-proc.exp takes a lot of time on skip_opencl_tests)
PR testsuite/25016 (Test-case failures for -pie)
GDB 8.3 includes the following changes and enhancements:
* Support for new native configurations (also available as a target configuration):
- RISC-V GNU/Linux (riscv*-*-linux*)
- RISC-V FreeBSD (riscv*-*-freebsd*)
* Support for new target configurations:
- CSKY ELF (csky*-*-elf)
- CSKY GNU/Linux (csky*-*-linux)
- NXP S12Z ELF (s12z-*-elf)
- OpenRISC GNU/Linux (or1k*-*-linux*)
* Native Windows debugging is only supported on Windows XP or later.
* The Python API in GDB now requires Python 2.6 or later.
* GDB now supports terminal styling for the CLI and TUI.
Source highlighting is also supported by building GDB with GNU
Highlight.
* Experimental support for compilation and injection of C++ source
code into the inferior (requires GCC 7.1 or higher, built with
libcp1.so).
* GDB and GDBserver now support IPv6 connections.
* Target description support on RISC-V targets.
* Various enhancements to several commands:
- "frame", "select-frame" and "info frame" commands
- "info functions", "info types", "info variables"
- "info thread"
- "info proc"
- System call alias catchpoint support on FreeBSD
- "target remote" support for Unix Domain sockets.
* Support for displaying all files opened by a process
* DWARF index cache: GDB can now automatically save indices of DWARF
symbols on disk to speed up further loading of the same binaries.
* Various GDB/MI enhancements.
* GDBserver on PowerPC GNU/Linux now supports access to the PPR,
DSCR, TAR, EBB/PMU, and HTM registers.
* Ada task switching support when debugging programs built with
the Ravenscar profile added to aarch64-elf.
* GDB in batch mode now exits with status 1 if the last executed
command failed.
* Support for building GDB with GCC's Undefined Behavior Sanitizer.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 14 Oct 2019 12:37:25 +0000 (14:37 +0200)]
kernel: bump 4.19 to 4.19.79
Refreshed all patches.
Remove upstreamed (superseded):
- 950-0726-can-mcp251x-Allow-more-time-after-a-reset.patch
Compile-tested on: brcm2708, cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 14 Oct 2019 12:36:09 +0000 (14:36 +0200)]
kernel: bump 4.14 to 4.14.149
Refreshed all patches.
Altered patches:
- 820-sec-support-layerscape.patch
Compile-tested on: cns3xxx, layerscape
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 14 Oct 2019 10:59:09 +0000 (12:59 +0200)]
toolchain/musl: bump to version 1.1.24
1.1.24 release notes
new features:
- GLOB_TILDE extension to glob
- non-stub catgets localization API, using netbsd binary catalog format
- posix_spawn file actions for [f]chdir (extension, pending future standard)
- secure_getenv function (extension)
- copy_file_range syscall wrapper (Linux extension)
- header-level support for new linux features in 5.2
performance:
- new fast path for lrint (generic C version) on 32-bit archs
major internal changes:
- functions involving time are overhauled to be time64-ready in 32-bit archs
- x32 uses the new time64 code paths to replace nasty hacks in syscall glue
compatibility & conformance:
- support for powerpc[64] unaligned relocation types
- powerpc[64] and sh sys/user.h no longer clash with kernel asm/ptrace.h
- select no longer modifies timeout on failure (or at all)
- mips64 stat results are no longer limited to 32-bit time range
- optreset (BSD extension) now has a public declaration
- support for clang inconsistencies in wchar_t type vs some 32-bit archs
- mips r6 syscall asm no longer has invalid lo/hi register clobbers
- vestigial asm declarations of __tls_get_new are removed (broke some tooling)
- riscv64 mcontext_t mismatch glibc's member naming is corrected
bugs fixed:
- glob failed to match broken symlinks consistently
- invalid use of interposed calloc to allocate initial TLS
- various dlsym symbol resolution logic errors
- semctl with SEM_STAT_ANY didn't work
- pthread_create with explicit scheduling was subject to priority inversion
- pthread_create failure path had data race for thread count
- timer_create with SIGEV_THREAD notification had data race getting timer id
- wide printf family failed to support l modifier for float formats
arch-specific bugs fixed:
- x87 floating point stack imbalance in math asm (i386-only CVE-2019-14697)
- x32 clock_adjtime, getrusage, wait3, wait4 produced junk (struct mismatches)
- lseek broken on x32 and mipsn32 with large file offsets
- riscv64 atomics weren't compiler barriers
- riscv64 atomics had broken asm constraints (missing earlyclobber flag)
- arm clone() was broken when compiled as thumb if start function returned
- mipsr6 setjmp/longjmp did not preserve fpu register state correctly
Refreshed all patches.
Removed upstreamed.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Jo-Philipp Wich [Tue, 15 Oct 2019 13:51:11 +0000 (15:51 +0200)]
iwinfo: update to latest Git HEAD
a29b7d4 nl80211: align path to phy mapping logic with mac80211.sh
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Hans Dedecker [Mon, 14 Oct 2019 19:31:35 +0000 (21:31 +0200)]
odhcpd: update to latest git HEAD
9a4531a ndp: fix endian issue
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Adrian Schmutzler [Sun, 22 Sep 2019 09:57:14 +0000 (11:57 +0200)]
treewide: move MAC address patch functions to common library
This unifies MAC address patch functions and moves them to a
common script. While those were implemented differently for
different targets, they all seem to do the same. The number of
different variants is significantly reduced by this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 22 Sep 2019 09:57:13 +0000 (11:57 +0200)]
treewide: move calibration data extraction function to library
This moves the almost identical calibration data extraction
functions present multiple times in several targets to a single
library file /lib/functions/caldata.sh.
Functions are renamed with more generic names to merge different
variants that only differ in their names.
Most of the targets used find_mtd_chardev, while some used
find_mtd_part inside the extraction code. To merge them, the more
abundant version with find_mtd_chardev is used in the common code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[rebase on latest master; add mpc85xx]
Signed-off-by: David Bauer <mail@david-bauer.net>
Adrian Schmutzler [Sat, 28 Sep 2019 13:12:55 +0000 (15:12 +0200)]
base-files: move xor() from caldata extraction to functions.sh
The xor() function is defined in each of the caldata extraction
scripts for several targets. Move it to functions.sh to reduce
duplicate code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Roger Pueyo Centelles [Mon, 18 Mar 2019 12:20:47 +0000 (13:20 +0100)]
ath79: add support for COMFAST CF-E313AC
This patch adds support for the COMFAST CF-E313AC, an outdoor wireless
CPE with two Ethernet ports and a 802.11ac radio.
Specifications:
- QCA9531 SoC
- 650/400/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps WAN Ethernet, 48V PoE-in
- 1x 10/100 Mbps LAN Ethernet, pass-through 48V PoE-out
- 1x manual pass-through PoE switch
- 64 MB RAM (DDR2)
- 16 MB FLASH
- QCA9886 2T2R 5 GHz 802.11ac, 23 dBm
- 12 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1)
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new one, so a factory reset will be
needed. To do so, once the new firmware is flashed, enter into failsafe
mode by pressing the reset button several times during the boot
process, while the WAN LED flashes, until it starts flashing faster.
Once in failsafe mode, perform a factory reset as usual.
Alternatively, the U-boot bootloader contains a recovery HTTP server
to upload the firmware. Push the reset button while powering the
device on and keep it pressed for >10 seconds. The device's LEDs will
blink several times and the recovery page will be at
http://192.168.1.1; use it to upload the sysupgrade image.
Note:
Four MAC addresses are stored in the "art" partition (read-only):
- 0x0000: 40:A5:EF:AA:AA:A0
- 0x0006: 40:A5:EF:AA:AA:A2
- 0x1002: 40:A5:EF:AA:AA:A1
- 0x5006: 40:A5:EF:AA.AA:A3 (inside the 5 GHz calibration data)
The stock firmware assigns MAC addresses to physical and virtual
interfaces in a very particular way:
- eth0 corresponds to the physical Ethernet port labeled as WAN
- eth1 corresponds to the physical Ethernet port labeled as LAN
- eth0 belongs to the bridge interface br-wan
- eth1 belongs to the bridge interface br-lan
- eth0 is assigned the MAC from 0x0 (*:A0)
- eth1 is assigned the MAC from 0x1002 (*:A1)
- br-wan is forced to use the MAC from 0x1002 (*:A1)
- br-lan is forced to use the MAC from 0x0 (*:A0)
- radio0 uses the calibration data from 0x5000 (which contains
a valid MAC address, *:A3). However, it is overwritten by the
one at 0x6 (*:A2)
This commit preserves the LAN/WAN roles of the physical Ethernet
ports (as labeled on the router) and the MAC addresses they expose
by default (i.e., *:A0 on LAN, *:A1 on WAN), but swaps the position
of the eth0/eth1 compared to the stock firmware:
- eth0 corresponds to the physical Ethernet port labeled as LAN
- eth1 corresponds to the physical Ethernet port labeled as WAN
- eth0 belongs to the bridge interface br-lan
- eth1 is the interface at @wan
- eth0 is assigned the MAC from 0x0 (*:A0)
- eth1 is assigned the MAC from 0x1002 (*:A1)
- br-lan inherits the MAC from eth0 (*:A0)
- @wan inherits the MAC from eth1 (*:A1)
- radio0's MAC is overwritten to the one at 0x6
This way, eth0/eth1's positions differ from the stock firmware, but
the weird MAC ressignations in br-lan/br-wan are avoided while the
external behaviour of the router is maintained. Additionally, WAN
port is connected to the PHY gmac, allowing to monitor the link
status (e.g., to restart DHCP negotiation when plugging a cable).
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Roger Pueyo Centelles [Sun, 6 Oct 2019 19:07:33 +0000 (21:07 +0200)]
ramips: mt7621: Alternative name KE 2P for Phicomm K2P
The Phicomm KE 2P is identical to the already supported Phicomm K2P,
renamed for the European market. Use the ALT0 buildroot tags to show
both devices.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Stijn Tintel [Sun, 7 Apr 2019 22:39:34 +0000 (01:39 +0300)]
kernel: add kmod-iio-bme680
This driver supports the Bosch Sensortec BME680 gas, humidity, pressure
and temperature sensor.
Tested I2C and SPI modes on a Raspberry Pi Zero W.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Ali MJ Al-Nasrawy [Wed, 25 Sep 2019 14:47:13 +0000 (17:47 +0300)]
trelay: log "started" and "stopped"
It is informative especially when using multiple device pairs.
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
Ali MJ Al-Nasrawy [Wed, 25 Sep 2019 14:47:12 +0000 (17:47 +0300)]
trelay: fix deadlock on remove
Upon writing to "remove" file, debugfs_remove_recursive() blocks while
holding rtnl_lock. This is because debugfs' file_ops callbacks are
executed in debugfs_use_file_*() context which prevents file removal.
Fix this by only flagging the device for removal and then do the cleanup
in file_ops.release callback which is executed out of that context.
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
Ali MJ Al-Nasrawy [Wed, 25 Sep 2019 14:47:11 +0000 (17:47 +0300)]
trelay: handle netdevice events correctly
Since v3.11, netdevice notification data are of type
"struct netdev_notifier_info". Handle it as such!
This should fix a critical bug in which devices are unable get released
because trelay does not release resources in response to UNREGISTER
event spamming the log with something like:
unregister_netdevice: waiting for eth0.1 to become free. Usage count = 1
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
Ruixi Zhou [Sat, 5 Oct 2019 10:16:33 +0000 (18:16 +0800)]
kernel: NFSD: add dependency kmod-crypto-arc4 for kmod-fs-nfs-common-rpcsec
crypto-arc4 move into a module with commit
c3a78955f34a61d402044f357f54f21c75a19ff9,
fs-nfs-common-rpcsec compile error without arc4 support.
Ref: https://github.com/openwrt/packages/issues/9912
Fixes:
c3a78955f34a ("kernel: move crypto-arc4 into a module")
Signed-off-by: Ruixi Zhou <zhouruixi@gmail.com>
Val Kulkov [Mon, 7 Oct 2019 16:06:52 +0000 (12:06 -0400)]
base-files: coreutil-date breaks setting kernel timezone
"coreutil-date" package from the packages feed replaces the Busybox date
applet by symlinking /usr/bin/gnu-date to /bin/date. This prevents the system
init script from setting kernel timezone because the GNU date utility does not
provide such functionality:
root@OpenWrt:~# date -k
date: invalid option -- 'k'
Try 'date --help' for more information.
A specific reference to the Busybox date applet prevents alternative date
utilities from breaking the system init script.
Signed-off-by: Val Kulkov <val.kulkov@gmail.com>
Eneas U de Queiroz [Mon, 7 Oct 2019 21:02:38 +0000 (18:02 -0300)]
hostapd: adjust to removal of WOLFSSL_HAS_AES_GCM
WolfSSL is always built with AES-GCM support now.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Rosen Penev [Mon, 7 Oct 2019 22:59:52 +0000 (15:59 -0700)]
uClibc++: Fix three bugs
The first allows usage of several functions in the std namespace, which
broke compilation of gddrescue specifically with uClibc-ng and uClibc++.
The second allows usage of long long with normal C++11, which is part of
the standard. Before, std=gnu++11 needed to be passsed to work around it.
As a result of the second patch, the pedantic patch can safely be removed.
Both patches are upstream backports.
Added -std=c++11 to CFLAGS to guarentee proper inclusion of long long.
Added another patch that fixes a typo with the long long support. Sent to
upstream.
Fixed up license information according to SPDX.
Small cleanups for consistency.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Martin Schiller [Wed, 18 Sep 2019 04:35:10 +0000 (06:35 +0200)]
lantiq: add set_port_link feature to xrx200-net driver
This makes it possible to configure the link attributes (aneg, duplex,
speed) of each switch ports.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Scott Roberts [Fri, 27 Sep 2019 20:19:01 +0000 (14:19 -0600)]
mvebu: backport mvneta and comphy from linux 5.x
These patches backport support for the ARMADA 3700 COMPHY driver.
Also backported is the mvneta driver. This will allow switching
the SGMII speed using SMC calls. To support this you must update
the firmware using Marvells 18.12 version (this has now been
upstreamed). The mvneta driver allows 2500basex and 2500baset.
Signed-off-by: Scott Roberts <ttocsr@gmail.com>
Eubert Bao [Sat, 21 Sep 2019 04:44:16 +0000 (21:44 -0700)]
kirkwood: Fix FS#505 - Can't install LEDE on Linksys EA3500
The default sizes render Device/linksys_audi mage un-flashable.
Restore the pagesize, subpagesize, and blocksize for linksys_audi
from https://github.com/openwrt/archive.
Signed-off-by: Eubert Bao <bunnier@gmail.com>
Moritz Warning [Wed, 25 Sep 2019 22:02:21 +0000 (00:02 +0200)]
pistachio: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Sungbo Eo [Tue, 8 Oct 2019 14:25:03 +0000 (23:25 +0900)]
kernel: fix typos in video KernelPackage description
Fixes:
4b3d17b709a5 ("kernel: add kmod-fb-sys-ram")
Fixes:
b774acb47912 ("package/modules: add missing gspca video drivers for 2.6.32 (patch from #6595)")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Wed, 9 Oct 2019 02:15:55 +0000 (11:15 +0900)]
uboot-oxnas: remove unnecessary execute permission bit
.c files do not need to be executable. 644 is enough.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Wed, 9 Oct 2019 02:15:40 +0000 (11:15 +0900)]
ar71xx: remove unnecessary execute permission bit
.c files do not need to be executable. 644 is enough.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Wed, 9 Oct 2019 02:14:58 +0000 (11:14 +0900)]
mediatek: remove unnecessary execute permission bit
kernel config and dts files do not need to be executable. 644 is enough.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
DENG Qingfang [Sat, 12 Oct 2019 16:29:13 +0000 (00:29 +0800)]
tcpdump: update to 4.9.3
Fixed CVEs:
CVE-2017-16808
CVE-2018-10103
CVE-2018-10105
CVE-2018-14461
CVE-2018-14462
CVE-2018-14463
CVE-2018-14464
CVE-2018-14465
CVE-2018-14466
CVE-2018-14467
CVE-2018-14468
CVE-2018-14469
CVE-2018-14470
CVE-2018-14879
CVE-2018-14880
CVE-2018-14881
CVE-2018-14882
CVE-2018-16227
CVE-2018-16228
CVE-2018-16229
CVE-2018-16230
CVE-2018-16300
CVE-2018-16301
CVE-2018-16451
CVE-2018-16452
CVE-2019-15166
CVE-2019-15167
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
DENG Qingfang [Sat, 12 Oct 2019 16:28:32 +0000 (00:28 +0800)]
libpcap: update to 1.9.1
Fixed CVEs:
CVE-2018-16301
CVE-2019-15161
CVE-2019-15162
CVE-2019-15163
CVE-2019-15164
CVE-2019-15165
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Hauke Mehrtens [Sat, 12 Oct 2019 18:32:04 +0000 (20:32 +0200)]
mvebu: Refresh kernel 4.19 configuration
This refreshes the kernel 4.19 configuration, it looks like this was not
done initially.
When did a compile with the default settings I had to select some
kernel configuration options.
Fixes:
98684d99b250 ("mvebu: add kernel 4.19 support")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 12 Oct 2019 20:21:46 +0000 (22:21 +0200)]
kernel: Set GCC version to 80300 by default
The kernel 4.19 configuration contains the GCC version used, set it to
8.3.0 as this is now our default compiler.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 12 Oct 2019 20:31:38 +0000 (22:31 +0200)]
kernel: kmod-rtc-pcf2127: Fix dependencies
Add missing dependencies to i2c-core and regmap-spi. These get activated
when these modules are build in this driver, which is the case when we
build all modules. This fixes the build on some targets. This was found
by the buildbot.
Fixes:
34e2526f9fcc ("kernel: add kmod-rtc-pcf2127")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Moritz Warning [Thu, 11 Jul 2019 10:21:01 +0000 (12:21 +0200)]
brcm47xx: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Moritz Warning [Wed, 25 Sep 2019 22:13:13 +0000 (00:13 +0200)]
omap: split up DEVICE_TITLE
DEVICE_TITLE is split up into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Petr Štetiar [Fri, 11 Oct 2019 20:48:06 +0000 (22:48 +0200)]
libnl-tiny: fix package mirror hash
Current hash doesn't match with the content of the source tarball.
Fixes:
a92f74ba8db8 ("libnl-tiny: move source code into separate Git repository")
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Felix Fietkau [Fri, 11 Oct 2019 08:37:02 +0000 (10:37 +0200)]
build: fix menuconfig submenu sorting for gcc options
The hidden symbol GCC_USE_IREMAP was breaking it, move it to Config.version
instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 10 Oct 2019 21:09:35 +0000 (23:09 +0200)]
mt76: update to the latest version
71c2ef0420b5 mt76: fix aggregation stop issue
5b02a078d4a7 mt76: add missing locking around ampdu action
7d8764d320cf mt76: avoid enabling interrupt if NAPI poll is still pending
d94cc81d3980 mt76: drop rcu read lock in mt76_rx_aggr_stop
c11a4ad06d9d mt76: mt76x0: eeprom: add support for MAC address from OF
01642d8bed33 mt76: mt76x02: fix use-after-free in tx status code handling airtime
391e1488f885 mt76: add sanity check for a-mpdu rx wcid index
d3a589586d1b mt76: fix a-mpdu boundary detection issue for airtime reporting
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Hans Dedecker [Thu, 10 Oct 2019 19:53:38 +0000 (21:53 +0200)]
ppp: update to version 2.4.7.git-2019-10-04
0d004db Revert "pppd: Include time.h before using time_t"
e400854 pppdump: Eliminate printf format warning by using %zd
7f2f0de pppd: Refactor setjmp/longjmp with pipe pair in event wait loop
4e71317 make: Avoid using host include for cross-compiling
3202f89 pppoe: Remove the use of cdefs
d8e8d7a pppd: Remove unused rcsid variables
486f854 pppd: Fix GLIBC version test for non-glibc toolchains
b6cd558 pppd: Include time.h before using time_t
ef8ec11 radius: Fix compiler warning
f6330ec magic: Remove K&R style of arguments
347904e Add Submitting-patches.md
Remove patches 130-no_cdefs_h.patch, 131-missing_prototype_macro.patch,
132-fix_linux_includes.patch as fixed upstream
Refresh patches
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Felix Fietkau [Thu, 10 Oct 2019 11:42:56 +0000 (13:42 +0200)]
build: adjust gcc/g++ version checks for newer apple compilers
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Stefan Lippers-Hollmann [Wed, 9 Oct 2019 04:21:58 +0000 (06:21 +0200)]
mac80211: fix scan when operating on DFS channels in ETSI domains
In non-ETSI regulatory domains scan is blocked when operating channel
is a DFS channel. For ETSI, however, once DFS channel is marked as
available after the CAC, this channel will remain available (for some
time) even after leaving this channel.
Therefore a scan can be done without any impact on the availability
of the DFS channel as no new CAC is required after the scan.
Enable scan in mac80211 in these cases.
Signed-off-by: Aaron Komisar <aaron.komisar@tandemg.com>
Link: https://lore.kernel.org/r/1570024728-17284-1-git-send-email-aaron.komisar@tandemg.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Klaus Kudielka [Sat, 17 Aug 2019 13:52:01 +0000 (15:52 +0200)]
base-files: upgrade: add case to export_bootdevice
The factory uboot of the Turris Omnia boots with "root=b301", and we
instruct new users to sysupgrade from there (e.g. method 1, step 7).
Currently, this will fail with "Unable to determine upgrade device".
Add a new case to export_bootdevice, which parses the hex argument.
Fixes commit
2e5a0b81 ("mvebu: sysupgrade: sdcard: keep user added ...")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Oldřich Jedlička [Wed, 25 Sep 2019 19:45:42 +0000 (21:45 +0200)]
kernel: Fix off-by-one error in FIT mtd partition search.
This fixes off-by-one error introduced in commit
dc76900021b8
("kernel: Correctly search for the FIT image in mtd partition.")
Function `mtd_read` starts reading at `offset` and
needs `hdr_len` number of bytes to be available. Suppose
the easiest case when `offset` is `0` and `hdr_len` equals
to `mtd->size` - the `for` loop will not be entered even
when enough bytes are available to be read.
Same happens for any non-zero `offset`, when `hdr_len` is
just enough bytes to be read until `mtd->size` is reached.
Imagine that for example `mtd->size=5`, `offset=4` and
`hdr_len=1`. Then `offset+hdr_len=5` and the check has to
be `offset+hdr_len <= mtd->size`, i.e. `5 <= 5`. The
check for `offset + hdr_len` value needs to be inclusive,
therefore use `<=`.
Fixes:
dc76900021b8 ("kernel: Correctly search for the FIT image in mtd partition.")
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
[adjusted commit ref, fixes tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Paul Spooren [Tue, 8 Oct 2019 23:11:27 +0000 (13:11 -1000)]
kernel.mk: add KCFLAGS to make kmods reproducible
Some kmods (gpio-hotplug, wireguard) store the build path in the
compiled files and therefore make it harder to rebuild the official
binaries. As the same "iremap" function is used as for other binaries,
the change is compatible with gcc7 and 8.
Tested with both gcc7 and gcc8 resulting in build path independent
reproducible builds.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Wed, 2 Oct 2019 07:15:44 +0000 (21:15 -1000)]
toolchain/gcc: switch to version 8 by default
Main motivation for this commit is the introduction of
`-ffile-prefix-map=` which alows reproducible build path.
Compile tested on Linux and macOS without errors on the following
targets:
* ath79
* imx6
* brcm2708
* brcm63xx
* ixp4xx
* ramips
* sunxi
* x86
Thanks to Andre for the iremap fixup.
Ref: https://reproducible-builds.org/docs/build-path/
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Paul Spooren <mail@aparcar.org>
[refactored into separate commit]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Paul Spooren [Wed, 9 Oct 2019 04:36:53 +0000 (06:36 +0200)]
config: remove unused GCC_VERSION_4_8 config symbols
Lets remove unused GCC_VERSION_4_8 symbol after the series of patches
which has switched to target gcc-8 by default.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[refactored into separate commit]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Paul Spooren [Wed, 9 Oct 2019 04:41:00 +0000 (06:41 +0200)]
toolchain,build: prefer -ffile-prefix-map for gcc-8+
-ffile-prefix-map=OLD=NEW is an alias for both -fdebug-prefix-map and
-fmacro-prefix-map and is available since GCC 8.
Co-Developed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Paul Spooren <mail@aparcar.org>
[refactored into separate commit]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Paul Spooren [Wed, 9 Oct 2019 04:33:06 +0000 (06:33 +0200)]
openssl: add gcc-8 -ffile-prefix-map filter
gcc-8 switch -ffile-prefix-map helps a lot with reproducible build paths
in the resulting binaries.
Ref: https://reproducible-builds.org/docs/build-path/
Signed-off-by: Paul Spooren <mail@aparcar.org>
[refactored into separate commit]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Martin Schiller [Mon, 7 Oct 2019 04:52:08 +0000 (06:52 +0200)]
target/imagebuilder: use multi-thread support for xz compression
This speeds up the packing of the imagebuilder a lot:
imagebuilder-T0.tar.xz real 0m25.199s user 2m45.967s sys 0m1.218s
imagebuilder-T1.tar.xz real 2m02.543s user 2m02.418s sys 0m1.653s
imagebuilder-T2.tar.xz real 1m03.684s user 1m59.931s sys 0m0.587s
imagebuilder-T3.tar.xz real 0m48.033s user 2m02.904s sys 0m0.637s
imagebuilder-T4.tar.xz real 0m38.963s user 2m15.521s sys 0m0.783s
imagebuilder-T5.tar.xz real 0m37.994s user 2m21.461s sys 0m0.919s
imagebuilder-T6.tar.xz real 0m39.524s user 2m48.115s sys 0m1.279s
imagebuilder-T7.tar.xz real 0m34.061s user 2m45.097s sys 0m1.174s
imagebuilder-T8.tar.xz real 0m27.286s user 2m55.449s sys 0m1.329s
imagebuilder-T9.tar.xz real 0m25.205s user 2m44.894s sys 0m1.208s
To keep the output reproducible in any case, we enforce a minimum amount
of 2 threads.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[refactored into reusable NPROC var, more verbose commit message]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 7 Oct 2019 13:01:46 +0000 (15:01 +0200)]
libnl-tiny: move source code into separate Git repository
In order to make the source code usable and testable separately out of
buildroot.
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
projects / oweals / openwrt.git / log