config: cadence_spi: Remove defines read from DT

Cleanup unused #define values that are read from the DT.

Tested on TI K2G platform:
Tested-by: Vignesh R <vigneshr@ti.com>
Tested on a socfpga-cyclonev board:
Tested-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Signed-off-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Marek Vasut <marex@denx.de>

dts: cadence_spi: Sync DT bindings with Linux

Adopt the Linux DT bindings and clean-up duplicate
and unused values.

Fix indentation of the QSPI node in the keystone k2g
device tree.

Tested on TI K2G platform:
Tested-by: Vignesh R <vigneshr@ti.com>
Tested on a socfpga-cyclonev board:
Tested-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Signed-off-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Marek Vasut <marex@denx.de>

spi: cadence_spi: Sync DT bindings with Linux

Adopt the Linux DT bindings. This also fixes an issue
with the indaddrtrig register on the Cadence QSPI
device being programmed with the wrong value for the
socfpga arch.

Tested on TI K2G platform:
Tested-by: Vignesh R <vigneshr@ti.com>
Tested on a socfpga-cyclonev board:
Tested-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Signed-off-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Marek Vasut <marex@denx.de>

spi: kirkwood_spi: implement workaround for FE-9144572

Erratum NO. FE-9144572: The device SPI interface supports frequencies of
up to 50 MHz.  However, due to this erratum, when the device core clock
is 250 MHz and the SPI interfaces is configured for 50MHz SPI clock and
CPOL=CPHA=1 there might occur data corruption on reads from the SPI
device.

Implement the workaround by setting the TMISO_SAMPLE value to 0x2
in the timing1 register.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>

sf_probe: Merge spi_flash_probe_tail into spi_flash_probe

spi_flash_probe_tail is now only called from spi_flash_probe, hence we
can merge its body into spi_flash_probe.

Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>

spi: spi-uclass: Fix style violations

Remove a superfluous newline, and reduce the scope of a variable.

Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>

spi: sf_probe: Fix style violations

Fix two indention-related style violations.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Jagan Teki <jagan@openedev.com>

spi: Remove CONFIG_OF_SPI_FLASH

Previous patches removed the last usages of this config variable, so
that it is now obsolete.

This patch removes it from the whitelist.

Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>

spi: Remove spi_setup_slave_fdt

A previous patch removed the spi_flash_probe_fdt function, which
contained the last call of the spi_setup_slave_fdt function, which is
now equally obsolete.

This patch removes the function.

Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>

spi: Remove spi_flash_probe_fdt

Commit ba45756 ("dm: x86: spi: Convert ICH SPI driver to driver model")
removed the last usage of the spi_flash_probe_fdt function, rendering it
obsolete.

This patch removes the function.

Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>

spi: Remove obsolete spi_base_setup_slave_fdt

0efc024 ("spi_flash: Add spi_flash_probe_fdt() to locate SPI by FDT
node") added a helper function spi_base_setup_slave_fdt to to set up a
SPI slave from a given FDT blob. The only user was the exynos SPI
driver.

But commit 73186c9 ("dm: exynos: Convert SPI to driver model") removed
the use of this function, hence rendering it obsolete.

Remove this function, as well as the CONFIG_OF_SPI option, which guarded
only this function.

Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>

spi: Fix style violation and improve code

This patch fixes a printf specifier style violation, reduces the scope
of a variable, and turns a void pointer that is used with pointer
arithmetic into a u8 pointer.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Jagan Teki <jagan@openedev.com>

mips: bmips: enable the SPI flash on the Comtrend AR-5387un

It's a Macronix (mx25l12805d) 16 MB SPI flash.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

mips: bmips: add bcm63xx-hsspi driver support for BCM63268

This driver manages the high speed SPI controller present on this SoC.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

mips: bmips: add bcm63xx-hsspi driver support for BCM6328

This driver manages the SPI controller present on this SoC.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

dm: spi: add BCM63xx HSSPI driver

This driver is a simplified version of linux/drivers/spi/spi-bcm63xx-hsspi.c

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

mips: bmips: enable the SPI flash on the Netgear CG3100D

It's a Spansion (s25fl064a) 8 MB SPI flash.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

mips: bmips: enable the SPI flash on the Sagem F@ST1704

It's a Winbond (w25x32) 4 MB SPI flash.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

mips: bmips: add bcm63xx-spi driver support for BCM63268

This driver manages the low speed SPI controller present on this SoC.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

mips: bmips: add bcm63xx-spi driver support for BCM3380

This driver manages the SPI controller present on this SoC.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

mips: bmips: add bcm63xx-spi driver support for BCM6358

This driver manages the SPI controller present on this SoC.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

mips: bmips: add bcm63xx-spi driver support for BCM6348

This driver manages the SPI controller present on this SoC.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

mips: bmips: add bcm63xx-spi driver support for BCM6338

This driver manages the SPI controller present on this SoC.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

dm: spi: add BCM63xx SPI driver

This driver is a simplified version of linux/drivers/spi/spi-bcm63xx.c

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

drivers: spi: consider command bytes when sending transfers

Command bytes are part of the written bytes and they should be taken into
account when sending a spi transfer.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

drivers: spi: allow limiting reads

For some SPI controllers it's not possible to keep the CS active between
transfers and they are limited to a known number of bytes.
This splits spi_flash reads into different iterations in order to respect
the SPI controller limits.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

wait_bit: use wait_for_bit_le32 and remove wait_for_bit

wait_for_bit callers use the 32 bit LE version

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

wait_bit: add 8/16/32 BE/LE versions of wait_for_bit

Add 8/16/32 bits and BE/LE versions of wait_for_bit.
This is needed for reading registers that are not aligned to 32 bits, and for
Big Endian platforms.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>

doc: bindings: soft-spi: update documentation to match the code

Linux bindings have been introduced in the code (removing the U-Boot
specific ones) without documentation update. Compatible string has
changed, as well as the four GPIO properties. Reflect this by updating
the soft-spi.txt documentation.

Fixes: 102412c415 ("dm: spi: soft_spi: switch to use linux compatible string")
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>

Merge git://git.denx.de/u-boot-rockchip

Merge git://git.denx.de/u-boot-uniphier

ARM: uniphier: hide memory top by platform hook instead of CONFIG

I do not see a good reason to do this by a CONFIG option that affects
all SoCs.  The ram_size can be adjusted by dram_init() at run-time.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: uniphier: enable CONFIG_MMC_SDHCI_SDMA for ARMv8 SoCs

I did not enable SDMA when I added sdhci-cadence support because LD20
boards are equipped with a large amount memory beyond 32 bit address
range, but SDMA does not support the 64bit address.  U-Boot relocates
itself to the end of effectively available RAM.  This would make the
MMC enumeration fail because the buffer for EXT_CSD allocated in the
stack would go too high, then SDMA would fail to transfer data.

Recent SDHCI-compatible controllers support ADMA, but unfortunately
U-Boot does not support ADMA.

In the previous commit, I hided the DRAM area that exceeds the 32 bit
address range.  Now, I can enable CONFIG_MMC_SDHCI_SDMA.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

ARM: uniphier: do not use RAM that exceeds 32 bit address range

LD20 / PXs3 boards are equipped with a large amount of memory beyond
the 32 bit address range.  U-Boot relocates itself to the end of the
available RAM.

This is a problem for DMA engines that only support 32 bit physical
address, like the SDMA of SDHCI controllers.

In fact, U-Boot does not need to run at the very end of RAM.  It is
rather troublesome for drivers with DMA engines because U-Boot does
not have API like dma_set_mask(), so DMA silently fails, making the
driver debugging difficult.

Hide the memory region that exceeds the 32 bit address range.  It can
be done by simply carving out gd->ram_size.  It would also possible to
override get_effective_memsize() or to define CONFIG_MAX_MEM_MAPPED,
but dram_init() is a good enough place to do this job.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

rockchip: clk: bind reset driver

Bind rockchip reset to clock-controller with rockchip_reset_bind().

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

rockchip: reset: support a (common) rockchip reset drivers

Create driver to support the soft reset (i.e. peripheral)
of all Rockchip SoCs.

Example of usage:
i2c driver:
ret = reset_get_by_name(dev, "i2c", &reset_ctl);
if (ret) {
error("reset_get_by_name() failed: %d\n", ret);
}

reset_assert(&reset_ctl);
udelay(50);
reset_deassert(&reset_ctl);

i2c dts node:
resets = <&cru SRST_P_I2C1>, <&cru SRST_I2C1>;
reset-names = "p_i2c", "i2c";

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed commit tag:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Prepare v2018.01

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge git://git.denx.de/u-boot-imx

mtd: nand: mxs_nand_spl: Remove nand size print

It is not much needed to print nand size in SPL during nand boot,
and most of nand spl drivers doesn't print the same.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

board: engicam: Fix to remove legacy board/icorem6_rqs

board/icorem6_rqs/ is forgot to remove while moving
common board files together in
(sha1: 52aaddd6f415397bb2eae0d68a8cc1c5c4a98bb3)
"i..MX6: engicam: Add imx6q/imx6ul boards for existing boards"

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>

imx: initialize and use generic timer on i.MX 6UL/ULL

The i.MX 6UL/ULL feature a Cortex-A7 CPU which suppor the ARM
generic timer. This change makes use of the ARM generic timer in
U-Boot.

This is crucial to make the ARM generic timers usable in Linux since
timer_init() initalizes the system counter module, which is necessary
to use the generic timers CP15 registers.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

imx: introduce CONFIG_GPT_TIMER

Introduce a new config symbol to select the i.MX
General Purpose Timer (GPT).

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

imx: move CONFIG_SYSCOUNTER_TIMER to Kconfig

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

Merge git://git.denx.de/u-boot-x86

crypto/fsl: fix BLOB encapsulation and decapsulation

The blob_encap and blob_decap functions were not flushing the dcache
before passing data to CAAM/DMA and not invalidating the dcache when
getting data back.
Therefore, blob encapsulation and decapsulation failed with errors like
the following due to data cache incoherency:
"40000006: DECO: desc idx 0: Invalid KEY command"

To ensure coherency, we require the key_mod, src and dst buffers to be
aligned to the cache line size and flush/invalidate the memory regions.
The same requirements apply to the job descriptor.

Tested on an i.MX6Q board.

Reviewed-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>

x86: tangier: Add Bluetooth to ACPI table

As defined on reference board followed by Intel Edison a Bluetooth
device is attached to HSU0, i.e. PCI 0000:04.1.

Describe it in ACPI accordingly.

Note, we use BCM2E95 ID here as one most suitable for such device based
on the description in commit message of commit 89ab37b489d1
("Bluetooth: hci_bcm: Add support for BCM2E95 and BCM2E96")
in the Linux kernel source tree.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

x86: tangier: Use actual GPIO hardware numbers

The recent commit 03c4749dd6c7
  ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation")
in the Linux kernel reveals the issue we have in ACPI tables here,
i.e. we must use hardware numbers for GPIO resources and,
taking into consideration that GPIO and pin control are *different* IPs
on Intel Tangier, we need to supply numbers properly.

Besides that, it improves user experience since the official documentation
for Intel Edison board is referring to GPIO hardware numbering scheme.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

x86: Move commands from under arch/x86 to cmd/x86/

We only need to compile and link these files when building for full
U-Boot.  Move them to under cmd/x86/ to make sure they aren't linked in
and undiscarded due to u_boot_list_2_cmd_* being included).

Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

mx6ull: Handle the CONFIG_MX6ULL cases correctly

Since commit 051ba9e082f7 ("Kconfig: mx6ull: Deselect MX6UL from
CONFIG_MX6ULL") CONFIG_MX6ULL does not select CONFIG_MX6UL anymore, so
take this into consideration in all the checks for CONFIG_MX6UL.

This fixes a boot regression.

Reported-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Breno Lima <breno.lima@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>

Merge git://git.denx.de/u-boot-rockchip

ARM: imx: cm_fx6: env: don't run boot scripts twice

Boot scripts located in the root directory of the first partition of
USB, mmc, and SATA drives are executed twice: first by the distro boot
command and then by the legacy boot command. This may have weird side
effects if those scripts only change or extend the environment
(including parts of the boot command itself).

Removing the script execution from the legacy boot command has its own
caveats. For instance, the distro boot command may execute the boot.scr
on the mmc drive, then the boot.scr on the SATA drive, before the
legacy boot command actually boots from the mmc drive. However, the
current behavior would only execute the boot.scr once more before the
actual boot, but it does not prevent the script located on the SATA
drive from being executed, and thus, both scripts from being mixed up.

Considering that the legacy boot command is only in place to boot old
(standard) installations, let's go with the resolution having less
custom code and remove the script execution from the legacy boot
command.

Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

ARM: imx: cm_fx6: env: support distro boot command

The current default environment of the cm_fx6 is not suitable for
booting modern distributions.

Instead of extending the custom environment, let's use the distro
boot command, which has been developed for precisely this use case.

If the distro boot command fails, fall back to the old behavior
(except for USB drives where the old behaviour is completely covered
by the distro boot command). That way it is still possible to create
"rescue SD cards" for old installations (e.g. if one messes up the
on-flash environment).

Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

ARM: imx: cm_fx6: env: use standard variables

In preparation for supporting the distro boot command, introduce the
standard variables for specifying load addresses, which are documented
in README and doc/README.distro, and replace the custom variables
used so far with them.

Since the current address layout disregards an address for an initramfs,
also switch to the load addresses used and proven by other imx6 boards
(e.g. the wandboard and nitrogen6x), instead of going on with our own
way.

Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

rockchip: firefly-rk3399: enable SPL_ATF_NO_PLATFORM_PARAM

The Rockchip-released ATF for the Firefly apparently (i.e. Kever
reported this) does not tolerate a FDT being passed as the platform
parameter and will run into a hard stop.

To work around this limitation in the ATF parameter handling, we
enable SPL_ATF_NO_PLATFORM_PARAM (which will force passing NULL for
the platform parameters).

Note that this only affects this platform, as the ATF releases for the
RK3368 and RK3399 have always either ignored the platform parameter
(i.e. before the FDT-based parameters were supported) or support
receiving a pointer to a FDT.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

spl: atf: add SPL_ATF_NO_PLATFORM_PARAM option

While we expect to call a pointer to a valid FDT (or NULL) as the
platform parameter to an ATF, some ATF versions are not U-Boot aware
and have an insufficiently robust (or an overzealour) parameter
validation: either way, this may cause a hard-stop with uncooperative
ATF versions.

This change adds the option to suppress passing a platform parameter
and will always pass NULL.

Debug output from ATF w/ this option disabled (i.e. default):
      INFO:    plat_param_from_bl2: 0x291450
Debug output from ATF w/ this option enabled:
      INFO:    plat_param_from_bl2: 0

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

imx: spl: Fix NAND bootmode detection

commit 20f14714169 ("imx: spl: Update NAND bootmode detection bit")
broke the NAND bootmode detection by checking if
BOOT_CFG1[7:4] == 0x8 for NAND boot mode.
This commit essentially reverts it, while using the IMX6_BMODE_*
macros that were introduced since.

Tables 8-7 & 8-10 from IMX6DQRM say the NAND boot mode selection
is done when BOOT_CFG1[7] is 1, but BOOT_CFG1[6:4] is not
necessarily 0x0 in this case.
Actually, NAND boot mode is when 0x8 <= BOOT_CFG1[7:4] <= 0xf,
like it was in the code before.

Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Tim Harvey <tharvey@gateworks.com>

mx6: Add board mx6memcal for use in validating DDR

This is a virtual "board" that uses configuration files and
Kconfig to define the memory layout used by a real board during
the board bring-up process.

It generates an SPL image that can be loaded using imx_usb or
SB_LOADER.exe.

When run, it will generate a set of calibration constants for
use in either or both a DCD configuration file for boards that
use u-boot.imx or struct mx6_mmdc_calibration for boards that
boot via SPL.

In essence, it is a configurable, open-source variant of the
Freescale ddr-stress tool.

https://community.nxp.com/docs/DOC-105652

File mx6memcal_defconfig configures the board for use with
mx6sabresd or mx6qsabreauto.

Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>

video: Support multiple lines version string display

The calculation of left space for version string is not correct, should
use VIDEO_COLS not VIDEO_LINE_LEN / 2, otherwise we will get larger space
than actual have and cause string to overlay logo picture.

Also current version string display only supports two lines words at max.
This also causes overlay when the LCD pixel column size is not enough.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Anatolij Gustschin <agust@denx.de>

video: ipu: Fix dereferencing NULL pointer problem

The clk_set_rate function dereferences the clk pointer without
checking whether it is NULL. This may cause problem when clk is NULL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>

rockchip: board: lion-rk3368: reduce env-size default to 8KiB

We want to have the same configuration defaults for the RK3368-uQ7
as for the RK3399-Q7: this change reduces the default env-size to
8KiB to ensure that it does not overlap the boot-payload on SD/MMC
configurations.

References: commit fe529e6597c0 ("rockchip: rk3399-puma: reduce env size to 8kiB")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

boards: amlogic: khadas-vim: Typo fixup

Khadas VIM is an Open Source DIY Box manufactured by Shenzhen Wesion NOT 'Tomato'

The fix was provided by Khadas Team member 'numbqq'.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

Prepare v2018.01-rc3

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge branch 'master' of git://git.denx.de/u-boot-rockchip

power: tps65910: replace error() by pr_err()

The patch replaces the former error() by the new pr_err().
This makes the TPS65910 driver conform to Masahiro's patch
'treewide:replace with error() with pr_err()' introduced
October 2017.

Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Simon Glass <sjg@chromium.org>

configs: am335x_boneblack: Bring back missed bootcmd

Commit b6251db8c3f0 ("Kconfig: Introduce USE_BOOTCOMMAND and migrate
BOOTCOMMAND") removed CONFIG_BOOTCOMMAND option from
include/configs/am335x_evm.h file. But that option wasn't added to
defconfig files for BeagleBone Black board.

Because of this we can't boot Linux from SD card using just
"run bootcmd", getting next error:

    ** File not found /boot/undefined **

That's because "fdtfile" variable has "undefined" value by default, and
"bootcmd" doesn't call "run findfdt" command, which assigns "fdtfile" to
correct device tree file for current board name (obtained from EEPROM).

So we are forced to either call "run findfdt" command manually, or
assign manually "fdtfile=am335x-boneblack.dtb" (e.g. in uEnv.txt file).

Bring back CONFIG_BOOTCOMMAND to BBB defconfigs so that we can boot
Linux rootfs from SD card automatically without any addition actions.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

dm: core: remove orphaned parameter description in platdata.h

struct driver_info has no field 'flags'.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

ARM: omap3: evm: Refactor 'board_eth_init'

This commit clears 'ethaddr' before calling 'smc911x_initialize' to
allow the SROM MAC address to be assigned properly.

Signed-off-by: Derald D. Woods <woods.technical@gmail.com>

ARM: dts: omap3-evm: Enable DM and devicetree for TMDSEVM{3530, 3730}

This commit updates the configuration files needed to support OF_CONTROL
on the OMAP3 EVM baseboard.

Additionally:
- CONFIG_SYS_THUMB_BUILD is enabled
- CONFIG_SPL_ENV_SUPPORT is enabled

Tested using GCC 7.2.0 [--with-float=hard --with-mode=thumb].

Signed-off-by: Derald D. Woods <woods.technical@gmail.com>

ARM: dts: omap3-evm: Add support for TMDSEVM{3530, 3730}

This commit adds OMAP3 EVM devicetree files from Linux v4.15-rc3. Note
that this is the first addition of OMAP34XX devicetree files.

Signed-off-by: Derald D. Woods <woods.technical@gmail.com>

ARM: omap3: evm: Do not relocate FDT address

This commit keeps the 'fdtaddr' as provided by DEFAULT_LINUX_BOOT_ENV.

Signed-off-by: Derald D. Woods <woods.technical@gmail.com>

rockchip: dts: rk3399-evb: support boot from sd-card

Enable sdmmc node in SPL and add it to boot order.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed commit tags:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

rockchip: rk3399-puma: reduce env size to 8kiB

This commit changes the size of the enviroment (for the RK3399-Q7) to
8kiB for all possible locations of the environment (i.e. even when the
environment is saved to SD card).

With the default of 32kiB, the environment overwrites the SPL
stage which lives at 16kiB.

Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Reworked commit-message:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>

Merge git://git.denx.de/u-boot-imx

arm: imx: add tzic interrupt controller for imx53

Since commit 999a78d5cf00 ("scripts/dtc: Update to upstream version v1.4.5-3-gb1a60033c110")
dtc warns about:
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/serial@53fc0000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/ccm@53fd4000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/gpio@53fe4000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@60000000/sdma@63fb0000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@60000000/ethernet@63fec000

Fix this by adding a node for the tzic interrupt controller.
Copied from "<Linux>/arch/arm/boot/dts/imx53.dts"

Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

ARM: imx6: Disable DDR DRAM calibration DHCOM i.MX6 PDK

The DDR DRAM calibration doesn't work on T-topology sometimes, so disable it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

imx: Fix missing spl_sd configuration for wandboard.

In commit 6e6cf015e7cdd7ca83a933320a81201972bd5e5e ("Merge
git://www.denx.de/git/u-boot-imx") the line defining spl_sd
configuration for wandboard was removed, which resulted in no SPL
target being built.

Add it back.

Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

imx: Kconfig: Add HAS_CAAM option

Currently CONFIG_SECURE_BOOT is selecting FSL_CAAM for all i.MX devices,
this causes the following error when building mx6sl boards since
this SoC doesn't have the CAAM block:

In file included from drivers/crypto/fsl/jobdesc.c:12:0:
drivers/crypto/fsl/jobdesc.c: In function 'inline_cnstr_jobdesc_blob_dek':
include/fsl_sec.h:268:25: error: 'CAAM_ARB_BASE_ADDR' undeclared (first use
in this function)
 #define SEC_MEM_PAGE1  (CAAM_ARB_BASE_ADDR + 0x1000)
                         ^
drivers/crypto/fsl/jobdesc.c:140:21: note: in expansion of macro 'SEC_MEM_PAGE1'
  memcpy((uint32_t *)SEC_MEM_PAGE1, (uint32_t *)plain_txt, in_sz);
                     ^
include/fsl_sec.h:268:25: note: each undeclared identifier is reported only
once for each function it appears in
 #define SEC_MEM_PAGE1  (CAAM_ARB_BASE_ADDR + 0x1000)
                         ^
drivers/crypto/fsl/jobdesc.c:140:21: note: in expansion of macro 'SEC_MEM_PAGE1'
  memcpy((uint32_t *)SEC_MEM_PAGE1, (uint32_t *)plain_txt, in_sz);
                     ^
scripts/Makefile.build:280: recipe for target 'drivers/crypto/fsl/jobdesc.o'
failed
make[3]: *** [drivers/crypto/fsl/jobdesc.o] Error 1
scripts/Makefile.build:425: recipe for target 'drivers/crypto/fsl' failed
make[2]: *** [drivers/crypto/fsl] Error 2
scripts/Makefile.build:425: recipe for target 'drivers/crypto' failed
make[1]: *** [drivers/crypto] Error 2

Add HAS_CAAM configuration to avoid this error.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

Kconfig: mx6ull: Deselect MX6UL from CONFIG_MX6ULL

MX6UL contains features that MX6ULL doesn't support.
Deselect CONFIG_MX6UL and select SYS_L2CACHE_OFF and ROM_UNIFIED_SECTIONS.

The motivation for doing this change is that MX6UL supports CAAM and
MX6ULL does not.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

mx6sl: Select MX6SL option via Kconfig

Currently the MX6SL option is selected via CONFIG_SYS_EXTRA_OPTIONS,
but it is better to select it directly via Kconfig.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>

warp: imximage.cfg: Handle the CONFIG_SECURE_BOOT case

Secure boot is not enabled in warp imximage.cfg, add support for it.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

mx6slevk: imximage.cfg: Handle the CONFIG_SECURE_BOOT case

Secure boot is not enabled in mx6slevk imximage.cfg, add support for it.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>

mx6sxsabresd: Load the correct dtb for revA board

Currently only imx6sx-sdb.dtb is loaded, but if revA board is used the
correct dtb is imx6sx-sdb-reva.dtb, so make this possible.

While at it, remove an extra 'mmc dev'.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>

imx: Add a common way for detecting NXP boards revision

NXP development boards based on i.MX6/i.MX7 contain the board
revision information stored in the fuses.

Introduce a common function that can be shared by different boards and
convert mx6sabreauto to use this new mechanism.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>

ARM: imx: display5: config: Update display5_factory_defconfig to use USE_BOOTCOMMAND

This commit switch display5_factory_defconfig to use new, generic
USE_BOOTCOMMAND Kconfig option.

Signed-off-by: Lukasz Majewski <lukma@denx.de>

power: pmic.h: include dm/ofnode.h

Include dm/ofnode.h.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

ARM: imx: cm_fx6: remove esdhc init code from board file

Commit 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for MMC. Remove the old mmc init code, which
is no longer used, from the board file.

Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

ARM: imx: cm_fx6: remove sata init code from board file

Commit 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for AHCI. Remove the old, now unused, sata
init code from the board file.

Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

ARM: imx: cm_fx6: defconfig: enable CONFIG_DM_KEYBOARD

Commit 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for USB. But it missed to enable driver
model support for keyboards. As a result, USB keyboards do no longer
work.

Fix this by enabling driver model support for keyboards.

Fixes: 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support")
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

ARM: imx: cm-fx6: reinstate USB support by syncing the devicetree with Linux

Commit 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for USB, thereby effectively removing USB
support because the cm_fx6 devicetree in the U-Boot does *not* enable the
USB nodes.

Reinstate the USB support by syncing the devicetree with Linux whose
devicetree enables the USB nodes properly.

More precisely, use the devicetree found in Linux v4.15-rc1 with the
following two changes:
  1) Remove the audio mux; the required dt-bindings header is not
     present in the U-Boot.
  2) Keep the usdhc3 MMC controller node currently present in the
     U-Boot's devicetree to retain the ability to boot from MMC.

Fixes: 5248930ebf48 ("dm: imx: cm_fx6: Enable more driver model support")
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

board: ge: mx53ppd: Move check_time() to common location

We are going to be using check_time() on more than the mx53ppd, move this
function to a common location.

Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>

mx6_common: remove dead code

There is an #ifdef and #endif with nothing in between.  This patch simply
removes this dead/useless code.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

imx: Unify CONFIG_BOOTDELAY

In order to provide a consistent user experience for imx board users,
remove the custom CONFIG_BOOTDELAY values from defconfig files, so that
all boards can use the default two second delay.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>

Merge git://git.denx.de/u-boot-dm

Move CONFIG_PANIC_HANG to Kconfig

Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>

boards: ls1046ardb: disable unavailable "ethernet" node in dts

Linux device tree contains "ethernet" node for all possible
interface supported by SoC i.e. LS1046A.

It is not necessary for a SerDes protocol to support all possible
interface. So disable unavailable "ethernet" node in device tree.

Also, enable FDT_SEQ_MACADDR_FROM_ENV to fetch MAC address
sequentially from environment variables

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

arm: Add support of updating dts before fix-up

"ethernet" node fix-up for device tree happens before Linux boot.

There can be requirement of updating "ethernet" node even before
fix-up. So, add support of updating "ethernet" node.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

common: Fix-up MAC addr in dts by fetching env variable serially

The MAC addresses get fixed in the device tree for "ethernet" nodes
is by using trailing number behind "ethernet" found in "/aliases".
It may not be necessary for the "ethernet" nodes to be sequential.
There can be gaps in between or any node disabled

So provide a support to fetch MAC addr sequentially from env
and apply them to "ethernet" nodes in the order they appear in
device tree only if "ethernet" is not "disabled"

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

Merge git://git.denx.de/u-boot-x86

x86: tangier: Use official ACPI HID for FLIS IP

FLIS IP since now gets its own ACPI ID.
Drop PRP0001 workaround in favour of official ACPI HID.

Corresponding kernel commit dabd4bc6de2b

pinctrl: intel: merrifield: Introduce ACPI device table

in the pin control subsystem tree [1] targeting v4.16.

[1]: https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl.git/commit/?h=for-next&id=dabd4bc6de2b

Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

Merge git://git.denx.de/u-boot-spi