Martin Krause [Wed, 26 Sep 2007 15:55:56 +0000 (17:55 +0200)]
TQM885D: adjust for doubled flash sector size + some minor fixes
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Jens Gehrlein [Wed, 26 Sep 2007 15:55:54 +0000 (17:55 +0200)]
TQM885D: Exchanged SDRAM timing by a more relaxed timing.
CAS-Latency=2, Write Recovery Time tWR=2
The max. supported bus frequency is 66 MHz. Therefore, changed
threshold to switch from 1:1 mode to 2:1 from 80 MHz to 66 MHz.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Martin Krause [Wed, 26 Sep 2007 15:55:56 +0000 (17:55 +0200)]
TQM885D: use calculated cpuclk instead of measuring it
On the TQM885D the measurement of cpuclk with the PIT reference
timer ist not necessary. Since all module variants use the same
external 10 MHz oscillator, the cpuclk only depends on the PLL
configuration - which is readable by software.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Jens Gehrlein [Thu, 27 Sep 2007 12:54:46 +0000 (14:54 +0200)]
TQM885D: fix SDRAM refresh
At 133 MHz the current SDRAM refresh rate is too fast
(measured 4 * 1.17 us).
CFG_MAMR_PTA changes from 39 to 128. This result
in a refresh rate of 4 * 7.8 us at the default clock
66 MHz. At 133 MHz the value will be then 4 * 3.8 us.
This is a compromise until a new method is found to
adjust the refresh rate.
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Jens Gehrlein [Thu, 27 Sep 2007 12:54:46 +0000 (14:54 +0200)]
TQM860M: Support for 10col SDRAMs, max. 128 MiB
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Wolfgang Denk [Thu, 27 Dec 2007 00:12:56 +0000 (01:12 +0100)]
Merge branch 'master' of git://denx.de/git/u-boot-sh
Conflicts:
MAINTAINERS
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Wed, 26 Dec 2007 23:46:08 +0000 (00:46 +0100)]
Merge branch 'master' of git://denx.de/git/u-boot-avr32
Wolfgang Denk [Wed, 26 Dec 2007 23:22:24 +0000 (00:22 +0100)]
Merge branch 'testing' of git://denx.de/git/u-boot-fdt
Haavard Skinnemoen [Fri, 14 Dec 2007 14:36:18 +0000 (15:36 +0100)]
cfi_flash: Add manufacturer-specific fixups
Run fixups based on the JEDEC manufacturer ID independent of the
command set ID.
This changes current behaviour: Previously, geometry reversal for AMD
chips were done based on the command set ID, while they are now done
based on the JEDEC manufacturer and device ID.
Also add fixup for top-boot Atmel chips. A fixup is needed for
AT49BV6416(T) too, but since u-boot currently only reads the low byte
of the device ID, there's no way to tell it apart from AT49BV642D,
which should not have this fixup. Since AT49BV642D support is
necessary to get ATNGW100 board support into mainline, I've commented
out the fixup for now.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Fri, 14 Dec 2007 14:36:17 +0000 (15:36 +0100)]
cfi_flash: Add cmdset-specific init functions
Move things like reading JEDEC IDs and fixing up geometry reversal
into separate functions. The geometry reversal fixup is now performed
by altering the qry structure directly, which makes the sector init
code slightly cleaner.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Fri, 14 Dec 2007 14:36:16 +0000 (15:36 +0100)]
cfi_flash: Read whole QRY structure in one go
Read out the whole CFI Standard Query structure after successful cfi
identification. This allows subsequent code to access this information
directly without having to go through flash_read_uchar() and friends.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Mon, 17 Dec 2007 10:02:44 +0000 (11:02 +0100)]
AVR32: Fix logic inversion in disable_interrupts()
disable_interrupts() should return nonzero if interrupts were
_enabled_ before, not disabled.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Fri, 14 Dec 2007 15:51:22 +0000 (16:51 +0100)]
AVR32: Enable interrupts at bootup
The timer code depends on the timer interrupt to keep track of the
upper 32 bits of the cycle counter. This obviously doesn't work when
interrupts are disabled the whole time.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Thu, 15 Nov 2007 09:03:45 +0000 (10:03 +0100)]
AVR32: Fix wrong pin setup for USART3
As reported by Gerhard Berghofer:
in "gpio_enable_usart3" the correct pins for USART 3 are PB17 and PB18
instead of PB18 and PB19.
which is obviously correct. There's currently no code that uses
USART3, but custom boards may run into problems.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Thu, 1 Nov 2007 11:44:20 +0000 (12:44 +0100)]
README: Remove ATSTK1000 daughterboard list
As noted by Kim Phillips, these lists tend to become out of date.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Tue, 30 Oct 2007 13:56:36 +0000 (14:56 +0100)]
Add ATSTK100[234] to MAINTAINERS
Add all the ATSTK1000 daughterboards to MAINTAINERS along with their
"mother". Also update the entry for ATSTK1000 to be not only about the
AP7000 CPU; it's intended to handle all CPUs in the AT32AP family.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Mon, 29 Oct 2007 12:02:54 +0000 (13:02 +0100)]
AVR32: Add support for the ATSTK1004 board
ATSTK1004 is a daughterboard for ATSTK1000 with the AT32AP7002 CPU,
which is a derivative of AT32AP7000.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Mon, 29 Oct 2007 12:02:54 +0000 (13:02 +0100)]
AVR32: Add support for the ATSTK1003 board
ATSTK1003 is a daughterboard for ATSTK1000 with the AT32AP7001 CPU,
which is a derivative of AT32AP7000.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Mon, 29 Oct 2007 12:23:33 +0000 (13:23 +0100)]
AVR32: Make some AT32AP700x peripherals optional
Add a chip-features file providing definitions of the form
AT32AP700x_CHIP_HAS_<peripheral>
to indicate the availability of the given peripheral on the currently
selected chip.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Mon, 29 Oct 2007 12:09:56 +0000 (13:09 +0100)]
AVR32: Rename at32ap7000 -> at32ap700x
The SoC-specific code for all the AT32AP700x CPUs is practically
identical; the only difference is that some chips have less features
than others. By doing this rename, we can add support for the AP7000
derivatives simply by making some features conditional.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Fri, 29 Jun 2007 16:22:34 +0000 (18:22 +0200)]
atmel_mci: Show SR when block read fails
Show controller status as well as card status when an error occurs
during block read.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Thu, 13 Dec 2007 11:56:34 +0000 (12:56 +0100)]
cfi_flash: Use map_physmem() and unmap_physmem()
Use map_physmem() and unmap_physmem() to convert from physical to
virtual addresses. This gives the arch a chance to provide an uncached
mapping for flash accesses.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Thu, 13 Dec 2007 11:56:33 +0000 (12:56 +0100)]
Introduce map_physmem() and unmap_physmem()
map_physmem() returns a virtual address which can be used to access a
given physical address without involving the cache. unmap_physmem()
should be called when the virtual address returned by map_physmem() is
no longer needed.
This patch adds a stub implementation which simply returns the
physical address cast to a uchar * for all architectures except AVR32,
which converts the physical address to an uncached virtual mapping.
unmap_physmem() is a no-op on all architectures, but if any
architecture needs to do such mappings through the TLB, this is the
hook where those TLB entries can be invalidated.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Thu, 13 Dec 2007 11:56:32 +0000 (12:56 +0100)]
cfi_flash: Introduce read and write accessors
Introduce flash_read{8,16,32,64) and flash_write{8,16,32,64} and use
them to access the flash memory. This makes it clearer when the flash
is actually being accessed; merely dereferencing a volatile pointer
looks just like any other kind of access.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Thu, 13 Dec 2007 11:56:31 +0000 (12:56 +0100)]
Implement __raw_{read,write}[bwl] on all architectures
This adds implementations of __raw_read[bwl] and __raw_write[bwl] to
m68k, ppc, nios and nios2. The m68k and ppc implementations were taken
from Linux.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Sat, 6 Oct 2007 16:55:36 +0000 (18:55 +0200)]
cfi_flash: Reorder functions and eliminate extra prototypes
Reorder the functions in cfi_flash.c so that each function only uses
functions that have been defined before it. This allows the static
prototype declarations near the top to be eliminated and might allow
gcc to do a better job inlining functions.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Thu, 13 Dec 2007 11:56:29 +0000 (12:56 +0100)]
cfi_flash: Make some needlessly global functions static
Make functions not declared in any header file static.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Thu, 13 Dec 2007 11:56:28 +0000 (12:56 +0100)]
cfi_flash: Break long lines
This patch tries to keep all lines in the cfi_flash driver below 80
columns. There are a few lines left which don't fit this requirement
because I couldn't find any trivial way to break them (i.e. it would
take some restructuring, which I intend to do in a later patch.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Bartlomiej Sieka [Tue, 11 Dec 2007 12:59:57 +0000 (13:59 +0100)]
CFI: synchronize command offsets with Linux CFI driver
Fixes non-working CFI Flash on the Inka4x0 board.
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Stefan Roese [Sat, 8 Dec 2007 07:25:09 +0000 (08:25 +0100)]
CFI: Coding style cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
Michael Schwingen [Fri, 7 Dec 2007 22:35:02 +0000 (23:35 +0100)]
CFI: support JEDEC flash roms in CFI-flash framework
The following patch adds support for non-CFI flash ROMS, by hooking into the
CFI flash code and using most of its code, as recently discussed here in the
thread "Mixing CFI and non-CFI flashs".
Signed-off-by: Michael Schwingen <michael@schwingen.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Gerald Van Baren [Thu, 29 Nov 2007 02:24:50 +0000 (21:24 -0500)]
Conditionally compile fdt_fixup_ethernet()
Fix compiler warnings: On boards that don't have ethernets defined,
don't compile fdt_fixup_ethernet().
Kumar Gala [Wed, 28 Nov 2007 03:59:46 +0000 (21:59 -0600)]
Convert boards that set memory node to use fdt_fixup_memory()
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 26 Nov 2007 23:06:15 +0000 (17:06 -0600)]
Added fdt_fixup_stdout that uses aliases to set linux,stdout-path
We use a combination of the serialN alias and CONFIG_CONS_INDEX to
determine which serial alias we should set linux,stdout-path to.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 26 Nov 2007 20:57:45 +0000 (14:57 -0600)]
Add common memory fixup function
Add the function fdt_fixup_memory() to fixup the /memory node of the fdt
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 26 Nov 2007 17:19:12 +0000 (11:19 -0600)]
Conditionally compile fdt_support.c
Modify common/Makefile to conditionally compile fdt_support.c based
on CONFIG_OF_LIBFDT.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 26 Nov 2007 16:41:40 +0000 (10:41 -0600)]
Fix build breakage due to libfdt import
The IDS8247 got lost in the update and need an API update
do to rename of functions in libfdt.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Gerald Van Baren [Sat, 24 Nov 2007 00:43:20 +0000 (19:43 -0500)]
Add spaces around the = in the fdt print format.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Nobuhiro Iwamatsu [Thu, 6 Dec 2007 16:25:38 +0000 (01:25 +0900)]
sh: Moved driver of the SuperH dependence
The composition of the directory in the drivers/ changed.
I moved SuperH serial driver and marubun PCMCIA driver.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 6 Dec 2007 16:20:25 +0000 (01:20 +0900)]
Merge git://www.denx.de/git/u-boot
Nobuhiro Iwamatsu [Thu, 6 Dec 2007 16:20:16 +0000 (01:20 +0900)]
Merge git://www.denx.de/git/u-boot
Conflicts:
drivers/Makefile
Wolfgang Denk [Thu, 6 Dec 2007 09:21:19 +0000 (10:21 +0100)]
Release v1.3.1
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Thu, 6 Dec 2007 09:21:03 +0000 (10:21 +0100)]
ADS5121 Board: fix compile problem.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sun, 2 Dec 2007 23:15:28 +0000 (00:15 +0100)]
Prepare for 1.3.1-rc1
Signed-off-by: Wolfgang Denk <wd@denx.de>
Nobuhiro Iwamatsu [Wed, 28 Nov 2007 16:21:54 +0000 (01:21 +0900)]
sh: Add SuperH boards maintainer to MAINTAINERS file
Add MS7750SE and MS7722SE's board maintainer to MAINTAINERS file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Wed, 28 Nov 2007 15:13:04 +0000 (00:13 +0900)]
sh: Add ms7750se support in MAKEALL
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Jean-Christophe PLAGNIOL-VILLARD [Tue, 27 Nov 2007 08:44:53 +0000 (09:44 +0100)]
sh: Add sh3 and sh4 support in MAKEALL
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Sat, 24 Nov 2007 17:51:17 +0000 (02:51 +0900)]
sh: Add document for SuperH.
This document is a summary of information concerning SuperH of U-Boot.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Sat, 24 Nov 2007 17:39:31 +0000 (02:39 +0900)]
sh: Add marubun's pcmcia driver
Marubun pcmcia is a chip for PCMCIA used with SuperH.
Of course, this can be used even by other architectures.
When use this driver, came to be able to use CompactFlash
and Ethernet.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Sat, 24 Nov 2007 17:32:13 +0000 (02:32 +0900)]
sh: Update SuperH SCIF driver
- Changed volatile unsigned to vu_.
- Changed Makefile for kconfig.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Wed, 28 Nov 2007 15:56:37 +0000 (00:56 +0900)]
Merge git://www.denx.de/git/u-boot
Conflicts:
drivers/Makefile
Wolfgang Denk [Mon, 26 Nov 2007 21:57:53 +0000 (22:57 +0100)]
Merge commit '
3deca9d'
Conflicts:
Makefile
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Mon, 26 Nov 2007 18:18:21 +0000 (19:18 +0100)]
Cleanup coding style; update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Mon, 26 Nov 2007 18:15:04 +0000 (19:15 +0100)]
Jean-Christophe PLAGNIOL-VILLARD [Sun, 25 Nov 2007 21:39:25 +0000 (22:39 +0100)]
MAKEALL: add missing 512x boards in ppc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 25 Nov 2007 17:45:47 +0000 (18:45 +0100)]
Makefile : fix tags ctags etags with new drivers organization
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 25 Nov 2007 17:45:47 +0000 (18:45 +0100)]
Makefile : fix tags ctags etags with new drivers organization
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 24 Nov 2007 20:26:56 +0000 (21:26 +0100)]
drivers/mtd : move mtd drivers to drivers/mtd
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 24 Nov 2007 20:17:55 +0000 (21:17 +0100)]
drivers/misc : move misc drivers to drivers/misc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 24 Nov 2007 20:13:59 +0000 (21:13 +0100)]
drivers/block : move block drivers to drivers/block
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 24 Nov 2007 19:59:50 +0000 (20:59 +0100)]
drivers/rtc : move rtc drivers to drivers/rtc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 24 Nov 2007 19:14:44 +0000 (20:14 +0100)]
drivers/hwmon : move hardware monitor drviers to drivers/hwmon
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 24 Nov 2007 18:46:45 +0000 (19:46 +0100)]
drivers/input : move input drivers to drivers/input
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 24 Nov 2007 18:40:11 +0000 (19:40 +0100)]
drivers/usb : move usb drivers to drivers/usb
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 24 Nov 2007 18:33:38 +0000 (19:33 +0100)]
drivers/serial : move serial drivers to drivers/serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 21 Nov 2007 20:19:24 +0000 (21:19 +0100)]
drivers/net : move net drivers to drivers/net
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Tue, 20 Nov 2007 19:41:48 +0000 (20:41 +0100)]
drivers/video : move video drivers to drivers/video
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Tue, 20 Nov 2007 19:33:09 +0000 (20:33 +0100)]
drivers/pcmcia : move pcmcia drivers to drivers/pcmcia
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Tue, 20 Nov 2007 19:28:09 +0000 (20:28 +0100)]
drivers/pci : move pci drivers to drivers/pci
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Wolfgang Denk [Thu, 22 Nov 2007 23:55:23 +0000 (00:55 +0100)]
Merge branch 'testing' of git://denx.de/git/u-boot-fdt
Gerald Van Baren [Thu, 22 Nov 2007 22:23:23 +0000 (17:23 -0500)]
Fix fdt printing for updated libfdt
Also improve printing (adopt dtc v1 "c style" hex format), whitespace cleanup.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Kumar Gala [Wed, 21 Nov 2007 19:30:15 +0000 (13:30 -0600)]
Add additional fdt fixup helper functions
Added the following fdt fixup helpers:
* do_fixup_by_prop{_u32} - Find matching nodes by property name/value
* do_fixup_by_compat{_u32} - Find matching nodes by compat
The _u32 variants work the same only the property they are setting
is know to be a 32-bit integer instead of a byte buffer.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 21 Nov 2007 17:11:03 +0000 (11:11 -0600)]
Add fdt_fixup_ethernet helper to set mac addresses
Added a fixup helper that uses aliases to set mac addresses
in the device tree based on the bd_t
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 21 Nov 2007 20:07:46 +0000 (14:07 -0600)]
Fix warnings from import of libfdt
cmd_fdt.c: In function fdt_print:
cmd_fdt.c:586: warning: assignment discards qualifiers from pointer target type
cmd_fdt.c:613: warning: assignment discards qualifiers from pointer target type
cmd_fdt.c:635: warning: assignment discards qualifiers from pointer target type
cmd_fdt.c:636: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 24 Oct 2007 16:04:22 +0000 (11:04 -0500)]
Update libfdt from device tree compiler (dtc)
Update libfdt to commit
8eaf5e358366017aa2e846c5038d1aa19958314e from
the device tree compiler (dtc) project.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Sun, 4 Nov 2007 00:46:28 +0000 (19:46 -0500)]
Move do_fixup* for libfdt into common code
Moved the generic fixup handling code out of cpu/mpc5xxx and cpu/mpc8260
into common/fdt_support.c and renamed:
do_fixup() -> do_fixup_by_path()
do_fixup_u32() -> do_fixup_by_path_u32()
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 25 Oct 2007 21:15:07 +0000 (16:15 -0500)]
Make no options to fdt print default to '/'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 24 Oct 2007 15:21:57 +0000 (10:21 -0500)]
Removed some nonused fdt functions and moved fdt_find_and_setprop out of libfdt
Removed:
fdt_node_is_compatible
fdt_find_node_by_type
fdt_find_compatible_node
To ease merge of newer libfdt as we aren't using them anywhere at this time.
Also moved fdt_find_and_setprop out of libfdt into fdt_support.c for the same
reason.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Grant Likely [Wed, 21 Nov 2007 16:19:37 +0000 (09:19 -0700)]
[BUILD] Remove libraries when updating autoconf.mk
Fix library problems caused by conditional compilation. Using
autoconf.mk to decide which files to compile has caused a problem when
changing configuration from one board to another without clearing out
the library (*.a) files.
It used to be that the linker was always passed the same list of .o
files when building the .a files. However, that is not longer true
with conditional compilation. Now, a different board config will have
a different file list passed to the linker. The problem occurs when
a library has already been built and the board config is changed.
Since the linker will update instead of replace a preexisting library,
then if the file list changes to remove some object files the old
objects will still exist in the library.
The solution is to remove all old library files when autoconf.mk is
made.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Kumar Gala [Wed, 21 Nov 2007 14:49:50 +0000 (08:49 -0600)]
[BUILD] conditionally compile libfdt/*.c in libfdt/Makefile
Modify libfdt/Makefile to conditionally compile the *.c files based
on the board config.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Grant Likely [Mon, 24 Sep 2007 15:05:31 +0000 (09:05 -0600)]
[BUILD] conditionally compile common/cmd_*.c in common/Makefile
Modify common/Makefile to conditionally compile the cmd_*.c files based
on the board config.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Grant Likely [Mon, 24 Sep 2007 15:05:31 +0000 (09:05 -0600)]
[BUILD] Generate include/autoconf.mk from board config files
Use cpp and sed to postprocess config.h and import the defined values
into include/autoconf.mk. autoconf.mk is then included by config.mk to
give 'make' access to the board configuration.
Doing this enables conditional compilation at the Makefile level instead
of by wrapping every .c file with #ifdef/#endif wrappers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Jean-Christophe PLAGNIOL-VILLARD [Tue, 20 Nov 2007 19:14:18 +0000 (20:14 +0100)]
drivers/i2c : move i2c drivers to drivers/i2c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Grant Likely [Tue, 20 Nov 2007 15:19:56 +0000 (08:19 -0700)]
Merge branch 'origin' into kconfig-for-1.3.1
Wolfgang Denk [Mon, 19 Nov 2007 21:20:24 +0000 (22:20 +0100)]
Prepare for 1.3.0 release.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Haiying Wang [Mon, 19 Nov 2007 15:02:13 +0000 (10:02 -0500)]
Move CONFIG_QE out of CONFIG_PCI wrap for MPC8568MDS
CONFIG_QE shouldn't be in the wrap of CONFIG_PCI, fix it.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Shinya Kuribayashi [Mon, 19 Nov 2007 02:14:16 +0000 (11:14 +0900)]
[MIPS] board/gth2/lowlevel_init.S: Fix a build warning
lowlevel_init.S: Assembler messages:
lowlevel_init.S:413: Warning: Pretending global symbol used as branch target is local.
Looking at codes, the `memtest' and `clearmem' are intentional mixed
use of `global symbols' and `label' for debugging purpose. To make it
build, just disable global-symbols-use for now. As a result `memtest'
still remains as unused, but leave it be...
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Wolfgang Denk [Mon, 19 Nov 2007 11:59:14 +0000 (12:59 +0100)]
Fix build problems with mp2usb board
Signed-off-by: Wolfgang Denk <wd@denx.de>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 18 Nov 2007 17:36:11 +0000 (18:36 +0100)]
s3c24x0: Fix usb_ohci.c missing in Makefile
and usb_ohci.c warning differ in signedness
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 18 Nov 2007 11:55:02 +0000 (12:55 +0100)]
pb1x00 board: Fix u16 status declaration when PCMCIA is defined
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Wolfgang Denk [Sun, 18 Nov 2007 16:11:09 +0000 (17:11 +0100)]
Fix compiler warnings for ARM systems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Sun, 18 Nov 2007 15:36:27 +0000 (16:36 +0100)]
Fix compiler warnings for PPC systems. Update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 17 Nov 2007 10:31:10 +0000 (11:31 +0100)]
Fix warning differ in signedness in net/net.c and net/nfs.c
Wolfgang Denk [Sun, 18 Nov 2007 00:26:14 +0000 (01:26 +0100)]
Merge branch 'master' of git://denx.de/git/u-boot-mips
Shinya Kuribayashi [Sat, 17 Nov 2007 11:42:45 +0000 (20:42 +0900)]
gth2.c: Fix a warning on gth2 build.
gth2.c: In function 'misc_init_r':
gth2.c:434: warning: pointer targets in passing argument 2 of 'setenv' differ in signedness
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Stefan Roese [Sat, 17 Nov 2007 06:58:25 +0000 (07:58 +0100)]
Fix warning differ in signedness in common/cmd_scsi.c
Signed-off-by: Stefan Roese <sr@denx.de>
Shinya Kuribayashi [Sat, 17 Nov 2007 11:05:26 +0000 (20:05 +0900)]
[MIPS] cpu/mips/config.mk: Fix GNU assembler minor version picker
Current trick to pick up GNU assembler minor version does not work with the
latest binutils (2007-03-01 or later) due to ${PKGVERSION} now default to
"(GNU Binutils) ".
$ sde-as --version |grep "GNU assembler"
GNU assembler 2.15.94 mipssde-6.02.02-
20050602
$ sde-as --version |grep "GNU assembler" |awk '{print $3}'
2.15.94
$ sde-as --version |grep "GNU assembler" |awk '{print $3}' |awk -F. '{print $2}'
15
$
$ mips-linux-as --version |grep "GNU assembler"
GNU assembler (GNU Binutils) 2.18
$ mips-linux-as --version |grep "GNU assembler" |awk '{print $3}'
(GNU
$ mips-linux-as --version |grep "GNU assembler" |awk '{print $3}' |awk -F. '{print $2}'
(no output)
$
As a result of above, you'll see many noises with such binutils:
make -C cpu/mips/
/bin/sh: line 0: [: : integer expression expected
/bin/sh: line 0: [: : integer expression expected
make[1]: Entering directory `/home/skuribay/devel/u-boot.git/cpu/mips'
mips-linux-gcc -D__ASSEMBLY__ -g -Os -D__KERNEL__ -DTEXT_BASE=0xB0000000 -I/home/skuribay/devel/u-boot.git/include -fno-builtin -ffreestanding -nostdinc -isystem /home/skuribay/devel/buildroot/build_mips/staging_dir/usr/bin/../lib/gcc/mips-linux-uclibc/4.2.1/include -pipe -DCONFIG_MIPS -D__MIPS__ -G 0 -mabicalls -fpic -pipe -msoft-float -march=4kc -mtune=4kc -EB -c -o incaip_wdt.o incaip_wdt.S
/bin/sh: line 0: [: : integer expression expected
mips-linux-gcc -D__ASSEMBLY__ -g -Os -D__KERNEL__ -DTEXT_BASE=0xB0000000 -I/home/skuribay/devel/u-boot.git/include -fno-builtin -ffreestanding -nostdinc -isystem /home/skuribay/devel/buildroot/build_mips/staging_dir/usr/bin/../lib/gcc/mips-linux-uclibc/4.2.1/include -pipe -DCONFIG_MIPS -D__MIPS__ -G 0 -mabicalls -fpic -pipe -msoft-float -march=4kc -mtune=4kc -EB -c -o cache.o cache.S
/bin/sh: line 0: [: : integer expression expected
mips-linux-gcc -g -Os -D__KERNEL__ -DTEXT_BASE=0xB0000000 -I/home/skuribay/devel/u-boot.git/include -fno-builtin -ffreestanding -nostdinc -isystem /home/skuribay/devel/buildroot/build_mips/staging_dir/usr/bin/../lib/gcc/mips-linux-uclibc/4.2.1/include -pipe -DCONFIG_MIPS -D__MIPS__ -G 0 -mabicalls -fpic -pipe -msoft-float -march=4kc -mtune=4kc -EB -Wall -Wstrict-prototypes -c -o asc_serial.o asc_serial.c
/bin/sh: line 0: [: : integer expression expected
This patch simplifies the trick and makes it work with both versions of gas.
I also replace an expensive `awk (or gawk)' with `cut'.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Shinya Kuribayashi [Sat, 17 Nov 2007 11:05:26 +0000 (20:05 +0900)]
[MIPS] Remove useless instructions for initializing $gp.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Shinya Kuribayashi [Sat, 27 Oct 2007 06:27:06 +0000 (15:27 +0900)]
[MIPS] MIPS 4K core: Coding style cleanups
No logical changes.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Shinya Kuribayashi [Sat, 17 Nov 2007 11:05:20 +0000 (20:05 +0900)]
[MIPS] gth2.c: Fix a warning on gth2 build.
gth2.c: In function 'misc_init_r':
gth2.c:434: warning: pointer targets in passing argument 2 of 'setenv' differ in signedness
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
projects / oweals / u-boot.git / log