ARM: dts: at91: sama5: Add the sfr node

For sama5d2, add the sfr node with syscon support.

In order to access the SFR_UTMICKTRIM register for the utmi clock
driver, add the phandle property for the utmi node to point to the
sfr node.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>

clk: at91: utmi: Set the reference clock frequency

By default, it is assumed that the UTMI clock is generated from
a 12 MHz reference clock (MAINCK). If it's not the case, the FREQ
field of the SFR_UTMICKTRIM has to be updated to generate the UTMI
clock in the proper way.

The UTMI clock has a fixed rate of 480 MHz. In fact, there is no
multiplier we can configure. The multiplier is managed internally,
depending on the reference clock frequency, to achieve the target
of 480 MHz.

The patch is cloned from the patch of mailing-list:
[PATCH v2] clk: at91: utmi: set the mainck rate

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
[trini: Depend on SPL_DM]
Signed-off-by: Tom Rini <trini@konsulko.com>

clk: Kconfig: Add dependences of SPL_CLK

The SPL_CLK config should depend on SPL && SPL_DM.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

Merge git://git.denx.de/u-boot-dm

patman: Fix error when the email blacklist is missing

This section of the settings file may be missing. Handle that gracefully
rather than emitting an error.

Also update patman to write this section when a new settings file is
created.

Fixes: e11aa602 (patman: add support for omitting bouncing addresses)

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chris Packham <judge.pckham@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>

ARM: davinci: Update da8xxevm Maintainers

The e-mail addresses for DA8XXEVM BOARD and DA850_AM18XXEVM BOARD
are invalid.

Remove DA8XXEVM.

Update DA850_AM18XXEVM to have me be the maintainer since I work
for Logic PD and have access to OMAP-L138 and AM1808 EVM kits.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_EMIF4 et al to Kconfig

This converts the following to Kconfig:
   CONFIG_EMIF4
   CONFIG_SDRC

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefano Babic <sbabic@denx.de>

Convert CONFIG_MAC_ADDR_IN_SPIFLASH et al to Kconfig

This converts the following to Kconfig:
   CONFIG_MAC_ADDR_IN_SPIFLASH
   CONFIG_MAC_ADDR_IN_EEPROM

Signed-off-by: Adam Ford <aford173@gmail.com>

davinci: da850evm: Make EEPROM MAC code configurable

There was a check for CONFIG_MAC_ADDR_IN_EEPROM and
a check for CONFIG_MAC_ADDR_IN_SPIFLASH, however
some of the EEPROM related code wasn't encapsulated
inside the #if defined statement so the EEPROM code
could get executed even when it wasn't explicitly
enabled or wanted.

Signed-off-by: Adam Ford <aford173@gmail.com>

include/configs: remove references to SMNAND_ENV_OFFSET

In mancy cases both CONFIG_ENV_OFFSET and CONFIG_ENV_ADDR point
to an otherwise-unused SMNAND_ENV_OFFSET.
This patch will set both CONFIG_ENV_OFFSET and CONFIG_ENV_ADDR to
whatever value was defined by SMNAND_ENV_OFFSET.

Signed-off-by: Adam Ford <aford173@gmail.com>

arm: dts: omap3: Re-sync DTS files with Linux 4.13-RC5

The DTS files had some spacing issues and they needed fixing. This
pull re-sync's the OMAP3xx related DTS files with Linux 4.13-RC5.

To keep the DTS and DTSI files clean and in sync with Linux, new
u-boot.dtsi files are added.

Signed-off-by: Adam Ford <aford173@gmail.com>
V3: The resync broke card detect on MMC1 on Logic PD's Torpedo,
    so we add the cd-invert to the Torpedo's -u-boot.dtsi file.

V2: Add the u-boot.dtsi files for OMAP3, OMAP36xx, and Torpedo
    Remove the need for the second patch in the series

omap3: omap3_logic: Finish enabling fastboot on MUSB

Either the USB and Fastboot were never finished, or somehow it got
lost.  This puts enough hooks back into omap3logic to enable
fastboot and hopefully prepare it for Kconfig conversion.

Signed-off-by: Adam Ford <aford173@gmail.com>

ARM: dts: ethernut5: Fix the build warning

Fix the building warning as below:
---8<----
Warning (reg_format): "reg" property in /i2c-gpio-0/pcf8563@50 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /i2c-gpio-0/pcf8563@50
Warning (avoid_default_addr_size): Relying on default #size-cells value for /i2c-gpio-0/pcf8563@50
--->8----

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

serial: nulldev: Add nulldev serial driver

Some device the serial console's initialization cannot run early during
the boot process. Hence, nulldev serial device is helpful on that
situation.

For example, if the serial module was implemented in FPGA. Serial
initialization is prohibited to run until the FPGA was programmed.

This commit is to adding nulldev serial driver. This will allows the
default console to be specified as a nulldev.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>

spl: add newline in debug output

With debug enabled, SPL output following these debug prints is on the
same line and it is hard to read. Fix it.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

ARM: DRA72x: Add support for detection of DRA71x SR 2.1

DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Add support for detection
of SR2.1 version of DRA71x family of processors.

Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

davinci: da850-evm: switch to using TI_COMMON_CMD_OPTIONS

Like the OMAP-L138 LCDK before it, let's move the da850-evm and
the variations to TI_COMMON_CMD_OPTIONS to cut back one some of the
defconfig entries.

Signed-off-by: Adam Ford <aford173@gmail.com>

linux/io.h: import generic ioread* / iowrite* accessors from Linux

Some drivers in Linux (ex. drivers/mtd/nand/denali.c) use
ioread*/iowrite* accessors.  Import them to make drivers more
synced.  I copied code from include/asm-generic/io.h of Linux.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

dma: import linux/dma-direction.h to consolidate enum dma_data_direction

Import include/linux/dma-direction.h from Linux 4.13-rc7 and delete
duplicated definitions of enum dma_data_direction.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

omap3: am3517_evm: Enable TI_COMMON_CMD_OPTION

Enable TI_COMMON_CMD_OPTIONS and remove similar options
from the defconfig. Updated with savedefconfig.

Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>

ARM: OMAP3: am3517_evm: Move header to ti_omap3_common.h

Much of the AM3517 functions are copies of the standard definitions
used in ti_omap3_common.h.  Moving to include a common file
reduces the amount of duplicative code and clutter.  A few
AM3517 specific functions (like EMIF4) are explictly defined
and a few items are undefined or redefined, but overall the number
of lines of code shink.

Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>

armv8: mmu: add space around operator

Add space around operator "+", make it
match the coding style.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: mmu: remove unused macro definition

Macro VA_BITS and PTE_BLOCK_BITS are not used
in the code, so remove them.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: York Sun <york.sun@nxp.com>

cosmetic: bootcount: correct comment for used scratch register

Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>

misc: i2c_eeprom: Add compatible for AT24MAC402

Add the new compatible "atmel,24mac402" to accommodate AT24MAC402.
The AT24MAC402 is a 2K Serial EEPROM and the 2-Kbit memory array
is internally organized as 16 pages of 16 bytes of EEPROM each.
The 48-bit EUI address in the AT24MAC402 are located in the extended
memory block.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>

misc: i2c_eeprom: Add compatible for 24AA02E48

Add the new compatible "microchip,24aa02e48" to accommodate 24AA02E48,
the 24AA02E48 is a 2K I2C Serial EEPROM with pre-programmed globally
unique, 48-bit node address, and 8-byte page size.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>

configs: k2g_evm: Remove PMMC loading environment commands

The PMMC firmware should be bundled with the FIT image for HS devices,
remove the steps that load and install this firmware outside of FIT.

Signed-off-by: Andrew F. Davis <afd@ti.com>

ARM: k2g: Add FIT image handler for PMMC firmware

The PMMC firmware should be bundled into a FIT image on HS
devices to allow authentication/decryption, add a handler to
process this PMMC firmware.

Signed-off-by: Andrew F. Davis <afd@ti.com>

image: Add TI PMMC image type

Add a new image type representing TI Power Management
Micro-Controller (PMMC) Firmware image type.

Signed-off-by: Andrew F. Davis <afd@ti.com>

examples: add fallback memcpy

Solves build issue:

  Building current source for 134 boards (12 threads, 1 job per thread)
         arm:  +   lsxhl
  +examples/api/vsprintf.o: In function `string16':
  +lib/vsprintf.c:278: undefined reference to `memcpy'
  +examples/api/uuid.o: In function `uuid_bin_to_str':
  +lib/uuid.c:197: undefined reference to `memcpy'
  +lib/uuid.c:199: undefined reference to `memcpy'
  +make[3]: *** [examples/api/demo] Error 1
  +make[2]: *** [examples/api] Error 2
  +make[1]: *** [examples] Error 2
  +make: *** [sub-make] Error 2
    133    0    1 /134    sheevaplug

Signed-off-by: Rob Clark <robdclark@gmail.com>

vsprintf.c: add GUID printing

This works (roughly) the same way as linux's, but we currently always
print lower-case (ie. we just keep %pUB and %pUL for compat with linux),
mostly just because that is what uuid_bin_to_str() supports.

  %pUb:   01020304-0506-0708-090a-0b0c0d0e0f10
  %pUl:   04030201-0605-0807-090a-0b0c0d0e0f10

It will be used by a later efi_loader paths for efi variables and for
device-path-to-text protocol, and also quite useful for debug prints
of protocol GUIDs.

Signed-off-by: Rob Clark <robdclark@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>

vsprintf.c: add UTF-16 string (%ls) support

This is convenient for efi_loader which deals a lot with UTF-16.  Only
enabled with CC_SHORT_WCHAR, leaving room to add a UTF-32 version when
CC_SHORT_WCHAR is not enabled.

Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

lib: add some utf16 handling helpers

We'll eventually want these in a few places in efi_loader, and also
vsprintf.

Signed-off-by: Rob Clark <robdclark@gmail.com>

kbuild: Enable -fshort-wchar

EFI_LOADER really wants UTF-16 strings (ie. %ls and L"string" are 16bit
chars instead of 32bit chars).  But rather than enabling -fshort-wchar
conditionally if EFI_LOADER is enabled, it was deemed preferrable to
globally switch.

Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Merge git://git.denx.de/u-boot-fsl-qoriq

Travis-CI: Update PATH

We now can no longer re-use the provided path and need to give the
full PATH we want used now.

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge git://git.denx.de/u-boot-dm

dm: test: replace dm_scan_dt() by of dm_extended_scan_fdt() in dm_do_test

This allows to scan the DT including all "clocks" node's sub-nodes
in which fixed-clock are defined.
All fixed-clock should be defined inside a clocks node which collect all
external oscillators. Until now, all clocks sub-nodes can't be binded except
if the "simple-bus" compatible string is added which is a hack.

Update test.dts by moving clk_fixed node inside clocks.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>

dm: core: add clocks node scan

Currently, all fixed-clock declared in "clocks" node in device tree
can be binded by clk_fixed_rate.c driver only if each of them have
the "simple-bus" compatible string.
This constraint has been invoked here [1].

This patch offers a solution to avoid adding "simple-bus" compatible
string to nodes that are not busses.

[1] https://patchwork.ozlabs.org/patch/558837/

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

patman: add support for omitting bouncing addresses

Add support for reading a list of bouncing addresses from a in-tree file
(doc/bounces) and from the ~/.patman config file. These addresses are
stripped from the Cc list.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com <mailto:philipp.tomsich@theobroma-systems.com>>

moveconfig: Use fd.write() instead of print >>

Adjust this code so that it can work with Python 2 and 3.

Fixes: d73fcb1 (moveconfig: Support building a simple config database)
Reported-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>

dm: core: Add ofnode_for_each_subnode()

Add a convenience macro to iterate over subnodes of a node. Make use of
this where appropriate in the code.

Signed-off-by: Simon Glass <sjg@chromium.org>

genconfig.py: Print defconfig next to warnings

At present we sometimes see warnings of the form:

/tmp/tmpMA89kB:36: warning: overriding the value of CMD_SPL.
Old value: "y", new value: "y".

This is not very useful as it does not show whch defconfig file it relates
to. Update the tool to show this.

Signed-off-by: Simon Glass <sjg@chromium.org>

dm: core: Show driver name with 'dm tree'

It is often useful to see which driver was actually selected for each
device. Add a new 'Driver' column to provide this information. Sample
output:

 Class       Probed   Driver     Name
----------------------------------------
 root        [ + ]    root_drive root_driver
 keyboard    [ + ]    i8042_kbd  |-- keyboard
 serial      [ + ]    ns16550_se |-- serial
 rtc         [   ]    rtc_mc1468 |-- rtc
 timer       [ + ]    tsc_timer  |-- tsc-timer
 syscon      [ + ]    ich6_pinct |-- pch_pinctrl
 pci         [ + ]    pci_x86    |-- pci
 northbridge [ + ]    bd82x6x_no |   |-- northbridge@0,0
 video       [ + ]    bd82x6x_vi |   |-- gma@2,0
 vidconsole0 [ + ]    vidconsole |   |   `-- gma@2,0.vidconsole0
...

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>

dm: core: Drop use of strlcpy()

We can use printf() to limit the string width. Adjust the code to do this
instead of using strlcpy() which is a bit clumbsy.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>

sandbox: Convert SANDBOX_BITS_PER_LONG to Kconfig

Convert SANDBOX_BITS_PER_LONG to Kconfig and assign it a correct
number depending on which host we are going to build and run.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

sandbox: Introduce Kconfig option for 32/64 bit host

It seems most of the time we are building and running sandbox on 64-bit host.
But we do support 32-bit host as well. Introduce Kconfig option for this.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

blk: dm: make blk_create_device() take a number of block instead of a size

There is an overflow problem when taking the size instead of the number
of blocks in blk_create_device(). This results in a wrong device size: the
device apparent size is its real size  modulo 4GB.
Using the number of blocks instead of the device size fixes the problem and
is more coherent with the internals of the block layer.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

misc: Kconfig: Add SPL_I2C_EEPROM option

This option is an SPL-variant of the I2C_EEPROM option to enable
the driver for generic I2C-attached EEPROMs for SPL.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: sama5d4_xplained: Set mac address from eeprom

Add the code to set the ethernet mac address from eeprom by using
the common code from the common folder.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: sama5d2_xplained: Replace code to set mac address

Replace the code to set the ethernet mac address with the code from
the common folder.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

board: atmel: Create board/$(VENDOR)/common folder

Create board/$(VENDOR)/common folder to accommodate the common code
shared by other atmel boards, now put the code to set ethernet mac
address from eeprom, which uses the i2c eeprom driver.

Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

env: ti: boot: Select dtb name for X15 revC

Select dtb name for am57xx BeagleBoard-X15 revC

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

board: ti: am57xx: Add dt support for BeagleBoard-X15 revC

Add support for selecting proper dtb for
am57xx BeagleBoard X15 revC u-boot from FIT

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

board: ti: am571x: Add 666MHz support for AM571x IDK

AM571x supports DDR running at 666MHz. Right now it is
clocked at 532MHz which is lower than what is supported.
In order to have maximum performance on AM571-IDK,
switch DDR to 666MHz.

Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

board: ti: dra76: Add dt support

Add support for selecting proper dtb for
dra76x u-boot from FIT.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

arm: dts: Add u-boot specific compatibles

Separate out u-boot specific compatibles from dts files.
This will help in syncing dts files in future.
Also these will get deleted eventually once respective drivers
are capable of handling Linux dts files.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

arm: dts: dra7: sync DT with latest Linux

Sync all dra7* specific dts files with the upstream
kernel including changes queued for 4.14

https://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap.git/log/?h=omap-for-v4.14/dt-v3

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

env: ti: boot: Select dtb name for dra76

Select dtb name for dra76-evm.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

board: ti: dra76-evm: Add support for powering on mmc ldo

ldo4 is used to poweron mmc on dra76-evm. Enable it.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

board: ti: dra76-evm: Add the pinmux data

Adding pinmux and IODELAY data for dra76-evm.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

board: ti: dra76-evm: Add DDR data

dra76-evm has the ddr parts connectedi running at 666MHz:
EMIF1: MT41K512M16HA-125 AIT:A  x 2
EMIF2: MT41K512M8RH-125-AAT:E x 4
Add support for configuring the above DDR parts.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

board: ti: dra76-evm: Add the pmic data

dra76-evm uses lp8736 and tps65917 pmic for powering on
various peripherals. Add data for these pmics and register
for dra76-evm.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

board: ti: dra76-evm: Add epprom support

The dra76-evm is a board based on TI's DRA76 processor
Add eeprom support

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

arm: dra76: Add support for ES1.0 detection

dra76 family is a high-performance, infotainment application
device, based on OMAP architecture on a 28-nm technology.
This contains most of the subsystems, peripherals that are
available on dra74, dra72 family. This SoC mainly features
Subsystems:
- 2 x Cortex-A15 with max speed of 1.8GHz
- 2 X DSP
- 2 X Cortex-M4 IPU
- ISS
- CAL
- DSS
- VPE
- VIP
Connectivity peripherals:
- 1 USB3.0 and 3 USB2.0 subsystems
- 1 x SATA
- 2 x PCI Express Gen2
- 3-port Gigabit ethernet switch
- 2 x CAN
- MCAN

Adding CPU detection support for the dra76 ES1.0 soc
and update prcm, control module, dplls data.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

arm: dra7: Kconfig: Select LP87565 related configs

LP87565 is present on dra76-evm. Select it for
TARGET_DRA7XX_EVM.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

palmas: Add support for powering different ldos

It is not necessary that ldo1 is used to power on mmc.
So, add support for passing ldo registers for powering on mmc.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

arm: omap5+: Add board specific ldo powering

It is not necessary all omap5+ based uses the same PMIC
to poweron mmc. So add support for enabling mmc based on board.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>

Merge branch 'master' of git://git.denx.de/u-boot-video

Prepare v2017.09

Signed-off-by: Tom Rini <trini@konsulko.com>

MAINTAINERS: board: qcom: db410c: Maintainer changed

Replacing original author Mateusz Kulikowski
<mateusz.kulikowski@gmail.com> as db410c maintainer

Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>

armv8: fsl-layerscape: Add back L3 flushing for all exception levels

CCN-504 HPF registers were believed to be accessible only from EL3.
However, recent tests proved otherwise. Remove checking for exception
level to re-enable L3 cache flushing for all levels.

Signed-off-by: York Sun <york.sun@nxp.com>
Tested-by: Zhao Qiang <qiang.zhao@nxp.com>

armv8: ls1088a: Enable PCIe in defconfigs

Enabled PCIe support and PCI command feature.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: ls1088a: add PCIe dts node

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: ls1088a: fix the MMU table for pcie config space

The pcie config space of ls1088a is different from ls2080a.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: fsl-layerscape: Fix MC reserved memory calculation

In case high region memory doesn't have enough space for Management
Complex (MC), the return value should indicate a failure so the
caller can handle it accordingly.

Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Ebony Zhu <ebony.zhu@nxp.com>

armv7: Add workaround for USB erratum A-009007

Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values

Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>

armv7: Add workaround for USB erratum A-008997

Low Frequency Periodic Singaling (LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter settings

Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>

armv7: Add workaround for USB erratum A-009798

The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receive
Compliance test failure for a 100mV threshold.

Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>

armv7: Add workaround for USB erratum A-009008

USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature

Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: Add workaround for USB erratum A-009007

Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values.

Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: Add workaround for USB erratum A-008997

Low Frequency Periodic Signaling(LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter
settings

Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: Add workaround for USB erratum A-009798

The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receiver
Compliance test failure for a 100mV threshold.

Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: Add workaround for USB erratum A-009008

USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature

Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: Add scfg_clrsetbits_32(), scfg_clrbits_32()

Some erratum patch might need it to program registers.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: ls1088aqds: Add support of EC1 and EC2

EC1 and EC2 are RGMII interface on ls1088aqds platform.
This patch add support of RGMII with PHY and MDIO

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: fsl-layerscape: Support to add RGMII for ls1088aqds

This patch adds support for RGMII protocol

NXP's LDPAA2 support RGMII protocol. LS1088A is the
first Soc supporting both RGMII and SGMII.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: ls1088aqds: Add support of LS1088AQDS

This patch add support of LS1088AQDS platform.

The LS1088A QorIQTM Development System (QDS) is a high-performance
computing, evaluation, and development platform that supports the
LS1088A QorIQ Architecture processor.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: ls1088ardb: Add support for LS1088ARDB platform

LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin
platform that supports the LS1088A family SoCs. This patch add basic
support of the platform.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Disabled NAND in board header file]
Reviewed-by: York Sun <york.sun@nxp.com>
WIP: disable NAND for LS1088ARDB

armv8: ls1088a: Add NXP LS1088A SoC support

LS1088A is compliant with the Layerscape Chassis Generation 3 with
eight ARM v8 Cortex-A53 cores in 2 cluster, CCI-400, one 64-bit DDR4
SDRAM memory controller with ECC, Data path acceleration architecture
2.0 (DPAA2), Ethernet interfaces (SGMIIs, RGMIIs, QSGMIIs, XFIs),
QSPI, IFC, PCIe, SATA, USB, SDXC, DUARTs etc.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: fsl-layerscape: Fix final MMU table for QSPI and IFC

For QSPI and IFC addresses execution shouldn't be allowed
when u-boot running from DDR. Revise the MMU final table
to enforce execute-never bits.

Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: fsl: Use correct conditional compile for ls1012a

According current code base, CONFIG_LS1012A should be
CONFIG_ARCH_LS1012A, or function fsl_fdt_disable(blob) will be
wrongly called to disable all dwc3 USB nodes on LS1012A, which
cause Linux USB function stop working at all.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>

drivers:net:fsl-mc: Update MC address calculation

Update MC address calculation as per MC design requirement of address
as least significant 512MB address of MC private allocated memory,
i.e. address should point to end address masked with 512MB offset in
private DRAM block.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
[YS: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>

armv8: fsl-lsch3: Make CCN-504 related code conditional

LS2080 family has CCN-504 cache coherent interconnet. Other SoCs
in LSCH3 family may have differnt interconnect.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>

spl: fit: Add booting OS first

If CONFIG_SPL_OS_BOOT is enabled, boot OS if kernel image is found
in FIT structure.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

spl: fit: Support both external and embedded data

SPL supports U-Boot image in FIT format which has data outside of
FIT structure. This adds support for embedded data for normal FIT
images.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

spl: fit: Eanble GZIP support for image decompression

Add Kconfig option SPL_GZIP and SPL_ZLIB to enable gunzip support for
SPL boot, eg. falcon boot compressed kernel image.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

cmd: spl: Fix compiling warning

Fix warning "cast from pointer to integer of different size".

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

tools: pblimage: Fix address calculation

The image size should be added to the initial pbl command, not bit
"ORed".

Signed-off-by: York Sun <york.sun@nxp.com>

armv8: LS2080ARDB: Add secure boot defconfig for QSPI boot.

Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[YS: dropped redundant commit message]
Reviewed-by: York Sun <york.sun@nxp.com>