+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2008 Extreme Engineering Solutions, Inc.
* Copyright 2007-2008 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
/*
*/
#define CONFIG_SYS_BOARD_NAME "XPedite5370"
#define CONFIG_SYS_FORM_3U_VPX 1
-#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xfff80000
-#endif
#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
#define CONFIG_PCIE1 1 /* PCIE controller 1 */
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
-#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
/*
* Multicore config
*/
-#define CONFIG_MP
#define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */
#define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */
/*
* DDR config
*/
-#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#define CONFIG_VERY_BIG_RAM
#ifndef __ASSEMBLY__
+#include <linux/stringify.h>
extern unsigned long get_board_sys_clk(unsigned long dummy);
extern unsigned long get_board_ddr_clk(unsigned long dummy);
#endif
/*
* Diagnostics
*/
-#define CONFIG_SYS_ALT_MEMTEST
-#define CONFIG_SYS_MEMTEST_START 0x10000000
-#define CONFIG_SYS_MEMTEST_END 0x20000000
#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
CONFIG_SYS_POST_I2C)
-#define I2C_ADDR_LIST {CONFIG_SYS_I2C_DS1621_ADDR, \
- CONFIG_SYS_I2C_DS4510_ADDR, \
- CONFIG_SYS_I2C_EEPROM_ADDR, \
- CONFIG_SYS_I2C_LM90_ADDR, \
- CONFIG_SYS_I2C_PCA953X_ADDR0, \
- CONFIG_SYS_I2C_PCA953X_ADDR1, \
- CONFIG_SYS_I2C_PCA953X_ADDR2, \
- CONFIG_SYS_I2C_PCA953X_ADDR3, \
- CONFIG_SYS_I2C_PEX8518_ADDR, \
- CONFIG_SYS_I2C_RTC_ADDR}
/* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */
#define I2C_ADDR_IGNORE_LIST {0x50}
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \
{0xf7f40000, 0xc0000} }
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
/*
* Serial Port
*/
-#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#define CONFIG_SYS_I2C_PEX8518_ADDR 0x70
/* I2C DS1631 temperature sensor */
-#define CONFIG_SYS_I2C_DS1621_ADDR 0x48
-#define CONFIG_DTT_DS1621
-#define CONFIG_DTT_SENSORS { 0 }
#define CONFIG_SYS_I2C_LM90_ADDR 0x4c
/* I2C EEPROM - AT24C128B */
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#define CONFIG_SYS_M41T11_BASE_YEAR 2000
-/* GPIO/EEPROM/SRAM */
-#define CONFIG_DS4510
-#define CONFIG_SYS_I2C_DS4510_ADDR 0x51
-
/* GPIO */
#define CONFIG_PCA953X
#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
/*
* Networking options
*/
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
-#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#define CONFIG_TSEC_TBI
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
#define CONFIG_ETHPRIME "eTSEC2"
#define TSEC2_PHYIDX 0
#define CONFIG_HAS_ETH1
-/*
- * Command configuration.
- */
-#define CONFIG_CMD_DS4510
-#define CONFIG_CMD_DS4510_INFO
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_PCA953X
-#define CONFIG_CMD_PCA953X_INFO
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PCI_ENUM
-#define CONFIG_CMD_REGINFO
-
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
-#define CONFIG_PANIC_HANG /* do not reset board on panic */
-#define CONFIG_PREBOOT /* enable preboot variable */
#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
/*
/*
* Environment Configuration
*/
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */
-#define CONFIG_ENV_SIZE 0x8000
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
/*
* Flash memory map:
projects / oweals / u-boot.git / blobdiff