/*
- * (C) Copyright 2007 Netstal Maschinen AG
+ * (C) Copyright 2007-2008 Netstal Maschinen AG
* Niklaus Giger (Niklaus.Giger@netstal.com)
*
* (C) Copyright 2006-2007
#define CONFIG_440EPX 1 /* Specific PPC440EPx */
#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_4xx 1 /* ... PPC4xx family */
-#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+#define CONFIG_HOSTNAME hcu5
+
+/*
+ * Include common defines/options for all boards produced by Netstal Maschinen
+ */
+#include "netstal-common.h"
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
-#define CONFIG_ADD_RAM_INFO 1 /* Print additional info */
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
-
-#define CFG_BOOT_BASE_ADDR 0xfff00000
-#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
-#define CFG_FLASH_BASE 0xfff80000 /* start of FLASH */
-#define CFG_MONITOR_BASE TEXT_BASE
-#define CFG_OCM_BASE 0xe0010000 /* ocm */
-#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */
-#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */
-#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000
-#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000
-#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000
-
-/* Don't change either of these */
-#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
-
-#define CFG_USB2D0_BASE 0xe0000100
-#define CFG_USB_DEVICE 0xe0000000
-#define CFG_USB_HOST 0xe0000400
+#define CONFIG_SYS_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */
+
+#define CONFIG_SYS_TLB_FOR_BOOT_FLASH 3
+#define CONFIG_SYS_BOOT_BASE_ADDR 0xfff00000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
+#define CONFIG_SYS_FLASH_BASE 0xfff80000 /* start of FLASH */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */
+#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_OCM_BASE
+#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */
+#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
+#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
+#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
+
+#define CONFIG_SYS_USB2D0_BASE 0xe0000100
+#define CONFIG_SYS_USB_DEVICE 0xe0000000
+#define CONFIG_SYS_USB_HOST 0xe0000400
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer
*----------------------------------------------------------------------*/
/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
-#define CFG_INIT_RAM_OCM 1 /* OCM as init ram */
-#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */
-#define CFG_INIT_RAM_END (4 << 10)
-#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_END (4 << 10)
+#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
-#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */
-#define CONFIG_BAUDRATE 9600
-#undef CONFIG_SERIAL_MULTI /* needed to be able to define
- CONFIG_SERIAL_SOFTWARE_FIFO, but
- CONFIG_SERIAL_SOFTWARE_FIFO (16) does not work */
-/* Size (bytes) of interrupt driven serial port buffer.
- * Set to 0 to use polling instead of interrupts.
- * Setting to 0 will also disable RTS/CTS handshaking.
- */
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#undef CONFIG_UART1_CONSOLE
-
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */
+#define CONFIG_BAUDRATE 115200
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
-#undef CFG_ENV_IS_IN_NVRAM
-#undef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_IS_IN_EEPROM
-#undef CFG_ENV_IS_NOWHERE
+#undef CONFIG_ENV_IS_IN_NVRAM
+#define CONFIG_ENV_IS_IN_FLASH
+#undef CONFIG_ENV_IS_IN_EEPROM
+#undef CONFIG_ENV_IS_NOWHERE
-#ifdef CFG_ENV_IS_IN_EEPROM
+#ifdef CONFIG_ENV_IS_IN_EEPROM
/* Put the environment after the SDRAM and bootstrap configuration */
-#define PROM_SIZE 2048
-#define CFG_BOOSTRAP_OPTION_OFFSET 512
-#define CFG_ENV_OFFSET (CFG_BOOSTRAP_OPTION_OFFSET + 0x10)
-#define CFG_ENV_SIZE (PROM_SIZE-CFG_ENV_OFFSET)
+#define PROM_SIZE 2048
+#define CONFIG_SYS_BOOSTRAP_OPTION_OFFSET 512
+#define CONFIG_ENV_OFFSET (CONFIG_SYS_BOOSTRAP_OPTION_OFFSET + 0x10)
+#define CONFIG_ENV_SIZE (PROM_SIZE-CONFIG_ENV_OFFSET)
#endif
-#ifdef CFG_ENV_IS_IN_FLASH
+#ifdef CONFIG_ENV_IS_IN_FLASH
/* Put the environment in Flash */
-#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
-#define CFG_ENV_ADDR ((-CFG_MONITOR_LEN)-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE 0x10000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */
+#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 8*1024 /* 8 KB Environment Sector */
/* Address and size of Redundant Environment Sector */
-#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+
#endif
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
-#define CFG_MBYTES_SDRAM (128) /* 128 MB or 256 MB */
-#define CFG_DDR_CACHED_ADDR 0x40000000 /* setup 2nd TLB cached here */
-#undef CONFIG_DDR_DATA_EYE /* Do not use DDR2 optimization */
-#define CONFIG_DDR_ECC 1 /* enable ECC */
+#define CONFIG_SYS_MBYTES_SDRAM (128) /* 128 MB or 256 MB */
+#define CONFIG_SYS_DDR_CACHED_ADDR 0x50000000 /* setup 2nd TLB cached here */
+#undef CONFIG_DDR_DATA_EYE /* Do not use DDR2 optimization */
+#define CONFIG_DDR_ECC 1 /* enable ECC */
+
+/* Following two definitions must be kept in sync with config.h of vxWorks */
+#define USER_RESERVED_MEM ( 0) /* in kB */
+#define PM_RESERVED_MEM ( 64) /* in kB: pmLib reserved area size */
+#define CONFIG_PRAM ( USER_RESERVED_MEM + PM_RESERVED_MEM )
+
+#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
+ /* 440EPx errata CHIP 11 */
/*-----------------------------------------------------------------------
* I2C stuff for a ATMEL AT24C16 (2kB holding ENV, we are using the
* the second internal I2C controller of the PPC440EPx
*----------------------------------------------------------------------*/
-#define CFG_SPD_BUS_NUM 1
-
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-
-/* This is the 7bit address of the device, not including P. */
-#define CFG_I2C_EEPROM_ADDR 0x50
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-
-/* The EEPROM can do 16byte ( 1 << 4 ) page writes. */
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07
-#define CFG_EEPROM_PAGE_WRITE_BITS 4
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#undef CFG_I2C_MULTI_EEPROMS
-
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run nfs\" to mount Linux root filesystem over NFS;"\
- "echo"
-
-#undef CONFIG_BOOTARGS
+#define CONFIG_SYS_SPD_BUS_NUM 1
/* Setup some board specific values for the default environment variables */
-#define CONFIG_HOSTNAME hcu5
-#define CONFIG_IPADDR 172.25.1.42
-#define CONFIG_ETHADDR 00:60:13:00:00:00 /* Netstal Machines AG MAC */
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-#define CONFIG_SERVERIP 172.25.1.3
-
-#define CFG_TFTP_LOADADDR 0x01000000 /* @16 MB */
+#define CONFIG_IPADDR 172.25.1.15
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "loadaddr=0x01000000\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "bootfile=hcu5/uImage\0" \
- "rootpath=/home/hcu/eldk/ppc_4xxFP\0" \
- "load=tftp 100000 hcu5/u-boot.bin\0" \
- "update=protect off FFFa0000 FFFFFFFF;era FFFa0000 FFFFFFFF;" \
- "cp.b 100000 FFFa0000 60000\0" \
- "upd=run load;run update\0" \
- "vx=tftp ${loadaddr} hcu5/hcu5_vx_rom;" \
- "setenv bootargs emac(0,0)hcu5_vx_rom e=${ipaddr} " \
- " h=${serverip} u=dpu pw=netstal8752 tn=hcu5 f=0x3008;" \
- "bootvx ${loadaddr}\0" \
+ CONFIG_NETSTAL_DEF_ENV \
+ CONFIG_NETSTAL_DEF_ENV_POWERPC \
""
-#define CONFIG_BOOTCOMMAND "run vx"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_M88E1111_PHY 1
#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */
-#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
-
-#define CONFIG_HAS_ETH0
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NET_MULTI 1
-#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
-#define CONFIG_PHY1_ADDR 1
+#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
+#define CONFIG_PHY1_ADDR 2
/* USB */
#define CONFIG_USB_OHCI
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_BSP
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_USB
+/* POST support */
+#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
+ CONFIG_SYS_POST_UART | \
+ CONFIG_SYS_POST_I2C | \
+ CONFIG_SYS_POST_CACHE | \
+ CONFIG_SYS_POST_FPU | \
+ CONFIG_SYS_POST_ETHER | \
+ CONFIG_SYS_POST_SPR)
+
+#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1 }
+#define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
+
#define CONFIG_SUPPORT_VFAT
/*-----------------------------------------------------------------------
* Miscellaneous configurable options
*----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
/*-----------------------------------------------------------------------
* PCI stuff
*----------------------------------------------------------------------*/
/* General PCI */
-#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI 1 /* include pci support */
#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */
-#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
+#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr map to CONFIG_SYS_PCI_MEMBASE*/
/* Board-specific PCI */
-#define CFG_PCI_TARGET_INIT
-#define CFG_PCI_MASTER_INIT
+#define CONFIG_SYS_PCI_TARGET_INIT
+#define CONFIG_SYS_PCI_MASTER_INIT
-#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
-#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
+#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
- * External Bus Controller (EBC) Setup
+ * Flash
*----------------------------------------------------------------------*/
-#define CFG_FLASH CFG_FLASH_BASE
-#define CFG_CS_1 0xC8000000 /* CAN */
-#define CFG_CS_2 0xCC000000 /* CPLD and IMC-Bus Standard */
-#define CFG_CPLD CFG_CS_2
-#define CFG_CS_3 0xCD000000 /* CPLD and IMC-Bus Fast */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- * Memory Bank 0 (BOOT-FLASH) initialization
- */
-#define CFG_BOOTFLASH_CS 0 /* Boot Flash chip connected to CSx */
-#define CFG_EBC_PB0AP 0x02005400
-#define CFG_EBC_PB0CR 0xFFF18000 /* (CFG_FLASH | 0xda000) */
-#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 32 /* max number of sectors on one chip */
-
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+/* Use common CFI driver */
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+/* board provides its own flash_init code */
+#define CONFIG_FLASH_CFI_LEGACY 1
+#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
+#define CONFIG_SYS_FLASH_LEGACY_512Kx8 1
-/* Memory Bank 1 CAN-Chips initialization */
-#define CFG_EBC_PB1AP 0x02054500
-#define CFG_EBC_PB1CR 0xC8018000
+/* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_EMPTY_INFO
-/* Memory Bank 2 CPLD/IMC-Bus standard initialization */
-#define CFG_EBC_PB2AP 0x01840300
-#define CFG_EBC_PB2CR 0xCC0BA000
-
-/* Memory Bank 3 IMC-Bus fast mode initialization */
-#define CFG_EBC_PB3AP 0x01800300
-#define CFG_EBC_PB3CR 0xCE0BA000
-
-/* Memory Bank 4 (not used) initialization */
-#undef CFG_EBC_PB4AP
-#undef CFG_EBC_PB4CR
-
-/* Memory Bank 5 (not used) initialization */
-#undef CFG_EBC_PB5AP
-#undef CFG_EBC_PB5CR
-
-#define HCU_CPLD_VERSION_REGISTER ( CFG_CPLD + 0x0F00000 )
-#define HCU_HW_VERSION_REGISTER ( CFG_CPLD + 0x1400000 )
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
/*-----------------------------------------------------------------------
- * Cache Configuration
+ * External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
-#define CFG_DCACHE_SIZE (32<<10) /* For AMCC 440 CPUs */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#define CFG_HUSH_PARSER /* use "hush" command parser */
-#ifdef CFG_HUSH_PARSER
- #define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_CS_1 0xC8000000 /* CAN */
+#define CONFIG_SYS_CS_2 0xCC000000 /* CPLD and IMC-Bus Standard */
+#define CONFIG_SYS_CPLD CONFIG_SYS_CS_2
+#define CONFIG_SYS_CS_3 0xCE000000 /* CPLD and IMC-Bus Fast */
+
+#define CONFIG_SYS_BOOTFLASH_CS 0 /* Boot Flash chip connected to CSx */
+#define CONFIG_SYS_EBC_PB0AP 0x02005400
+#define CONFIG_SYS_EBC_PB0CR 0xFFF18000 /* (CONFIG_SYS_FLASH | 0xda000) */
+#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
+
+/* Memory Bank 1 CAN-Chips initialization */
+#define CONFIG_SYS_EBC_PB1AP 0x02054500
+#define CONFIG_SYS_EBC_PB1CR 0xC8018000
+
+/* Memory Bank 2 CPLD/IMC-Bus standard initialization */
+#define CONFIG_SYS_EBC_PB2AP 0x01840300
+#define CONFIG_SYS_EBC_PB2CR 0xCC0BA000
+
+/* Memory Bank 3 IMC-Bus fast mode initialization */
+#define CONFIG_SYS_EBC_PB3AP 0x01800300
+#define CONFIG_SYS_EBC_PB3CR 0xCE0BA000
+
+/* Memory Bank 4 (not used) initialization */
+#undef CONFIG_SYS_EBC_PB4AP
+#undef CONFIG_SYS_EBC_PB4CR
+
+/* Memory Bank 5 (not used) initialization */
+#undef CONFIG_SYS_EBC_PB5AP
+#undef CONFIG_SYS_EBC_PB5CR
+
+#define HCU_CPLD_VERSION_REGISTER ( CONFIG_SYS_CPLD + 0x0F00000 )
+#define HCU_HW_VERSION_REGISTER ( CONFIG_SYS_CPLD + 0x1400000 )
+
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#ifdef CONFIG_SYS_HUSH_PARSER
+ #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
+
#endif /* __CONFIG_H */
projects / oweals / u-boot.git / blobdiff