Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx

[oweals/u-boot.git] / include / configs / cobra5272.h

diff --git a/include/configs/cobra5272.h b/include/configs/cobra5272.h
index 11dd4d712be372533e64fb2f008e7d3063b97f0e..c859616c68cb344273fcb58eb0afa2b861299836 100644 (file)
--- a/include/configs/cobra5272.h
+++ b/include/configs/cobra5272.h
@@ -1,13 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Configuation settings for the Sentec Cobra Board.
  *
  * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
- *
- * SPDX-License-Identifier:    GPL-2.0+
  */
 
 /* ---
- * Version: U-boot 1.0.0 - initial release for Sentec COBRA5272 board
+ * Version: U-Boot 1.0.0 - initial release for Sentec COBRA5272 board
  * Date: 2004-03-29
  * Author: Florian Schlote
  *
@@ -33,12 +32,6 @@
 #define CONFIG_SYS_CLK                 66000000
 #define CONFIG_SYS_SDRAM_SIZE          16              /* SDRAM size in MB */
 
-/* ---
- * Enable use of Ethernet
- * ---
- */
-#define CONFIG_MCFFEC
-
 /* Enable Dma Timer */
 #define CONFIG_MCFTMR
 
@@ -52,7 +45,6 @@
 
 #define CONFIG_MCFUART
 #define CONFIG_SYS_UART_PORT           (0)
-#define CONFIG_BAUDRATE                19200
 
 /* ---
  * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change
@@ -94,50 +86,20 @@
  * ---
  */
 
-#ifndef CONFIG_MONITOR_IS_IN_RAM
-#define CONFIG_ENV_OFFSET              0x4000
-#define CONFIG_ENV_SECT_SIZE   0x2000
-#define CONFIG_ENV_IS_IN_FLASH 1
-#else
-#define CONFIG_ENV_ADDR                0xffe04000
-#define CONFIG_ENV_SECT_SIZE   0x2000
-#define CONFIG_ENV_IS_IN_FLASH 1
-#endif
-
 #define LDS_BOARD_TEXT \
-        . = DEFINED(env_offset) ? env_offset : .; \
-        common/env_embedded.o (.text);
+       . = DEFINED(env_offset) ? env_offset : .; \
+       env/embedded.o(.text);
 
 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PING
-
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_LOADB
-#undef CONFIG_CMD_MII
 
 #ifdef CONFIG_MCFFEC
-#      define CONFIG_MII               1
 #      define CONFIG_MII_INIT          1
 #      define CONFIG_SYS_DISCOVER_PHY
 #      define CONFIG_SYS_RX_ETH_BUFFER 8
 #      define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-
-#      define CONFIG_SYS_FEC0_PINMUX           0
-#      define CONFIG_SYS_FEC0_MIIBASE          CONFIG_SYS_FEC0_IOBASE
-#      define MCFFEC_TOUT_LOOP         50000
 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
 #      ifndef CONFIG_SYS_DISCOVER_PHY
 #              define FECDUPLEX        FULL
@@ -157,12 +119,6 @@
 
 /*AUTOBOOT settings - booting images automatically by u-boot after power on*/
 
-#define CONFIG_BOOTDELAY       5               /* used for autoboot, delay in
-seconds u-boot will wait before starting defined (auto-)boot command, setting
-to -1 disables delay, setting to 0 will too prevent access to u-boot command
-interface: u-boot then has to reflashed */
-
-
 /* The following settings will be contained in the environment block ; if you
 want to use a neutral environment all those settings can be manually set in
 u-boot: 'set' command */
@@ -172,9 +128,6 @@ u-boot: 'set' command */
 #define CONFIG_BOOTCOMMAND     "bootm 0xffe80000"      /*Autoboto command, please
 enter a valid image address in flash */
 
-#define CONFIG_BOOTARGS                " "                     /* default bootargs that are
-considered during boot */
-
 /* User network settings */
 
 #define CONFIG_IPADDR 192.168.100.2            /* default board IP address */
@@ -182,24 +135,11 @@ considered during boot */
 
 #endif
 
-#define CONFIG_SYS_PROMPT              "COBRA > "      /* Layout of u-boot prompt*/
-
 #define CONFIG_SYS_LOAD_ADDR           0x20000         /*Defines default RAM address
 from which user programs will be started */
 
 /*---*/
 
-#define CONFIG_SYS_LONGHELP                            /* undef to save memory         */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE              1024            /* Console I/O Buffer Size      */
-#else
-#define CONFIG_SYS_CBSIZE              256             /* Console I/O Buffer Size      */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS             16              /* max number of command args   */
-#define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
-
 /*
  *-----------------------------------------------------------------------------
  * End of user parameters to be customized
@@ -211,9 +151,6 @@ from which user programs will be started */
  * ---
  */
 
-#define CONFIG_SYS_MEMTEST_START       0x400
-#define CONFIG_SYS_MEMTEST_END         0x380000
-
 /* ---
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)