powerpc, 8xx: remove support for 8xx

[oweals/u-boot.git] / include / configs / aria.h

diff --git a/include/configs/aria.h b/include/configs/aria.h
index c36cf33f070cdfff7fc7e6e4aa29fd0584704bf7..3612e037b9fcb9f05610c30a3ce57544bbdefda5 100644 (file)
--- a/include/configs/aria.h
+++ b/include/configs/aria.h
@@ -13,6 +13,7 @@
 #define __CONFIG_H
 
 #define CONFIG_ARIA 1
+
 /*
  * Memory map for the ARIA board:
  *
@@ -36,12 +37,6 @@
 #define        CONFIG_SYS_TEXT_BASE    0xFFF00000
 
 /* video */
-#undef CONFIG_VIDEO
-
-#if defined(CONFIG_VIDEO)
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#endif
 
 /* CONFIG_PCI is defined at config time */
 
@@ -314,7 +309,6 @@
 #error CONFIG_PSC_CONSOLE must be 3
 #endif
 
-#define CONFIG_BAUDRATE                        115200  /* ... at 115200 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE  \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 
@@ -324,10 +318,6 @@
 #define CONSOLE_FIFO_RX_ADDR           FIFOC_PSC3_RX_ADDR
 
 #define CONFIG_CMDLINE_EDITING         1       /* command line history */
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef  CONFIG_SYS_HUSH_PARSER
-#endif
 
 /*
  * PCI
@@ -346,37 +336,15 @@
 #define CONFIG_SYS_PCI_IO_PHYS         0x84000000
 #define CONFIG_SYS_PCI_IO_SIZE         0x01000000      /* 16M */
 
-#define CONFIG_PCI_PNP                 /* do pci plug-and-play */
-
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup */
 
 #endif
 
-/* I2C */
-#define CONFIG_HARD_I2C                        /* I2C with hardware support */
-#define CONFIG_I2C_MULTI_BUS
-
-/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SPEED           100000
-#define CONFIG_SYS_I2C_SLAVE           0x7F
-#if 0
-#define CONFIG_SYS_I2C_NOPROBES        {{0,0x69}}      /* Don't probe these addrs */
-#endif
-
 /*
  * IIM - IC Identification Module
  */
 #undef CONFIG_FSL_IIM
 
-/*
- * EEPROM configuration for Atmel AT24C32A-10TQ-2.7:
- * 16-bit addresses, 10ms write delay, 32-Byte Page Write Mode
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         2
-#define CONFIG_SYS_I2C_EEPROM_ADDR             0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  10
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      5
-
 /*
  * Ethernet configuration
  */
@@ -404,30 +372,12 @@
 #define CONFIG_LOADS_ECHO              1
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   1
 
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#undef CONFIG_CMD_FUSE
-#define CONFIG_CMD_I2C
-#undef CONFIG_CMD_IDE
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_PCI)
 #define CONFIG_CMD_PCI
 #endif
 
-#if defined(CONFIG_CMD_IDE) || defined(CONFIG_CMD_EXT2)
-#define CONFIG_DOS_PARTITION
-#define CONFIG_MAC_PARTITION
-#define CONFIG_ISO_PARTITION
-#endif /* defined(CONFIG_CMD_IDE) */
-
 /*
  * Dynamic MTD partition support
  */
@@ -520,11 +470,8 @@
 
 #define CONFIG_LOADADDR                        400000  /* default load addr */
 
-#define CONFIG_BOOTDELAY       5       /* -1 disables auto-boot */
 #undef  CONFIG_BOOTARGS                        /* the boot command will set bootargs */
 
-#define CONFIG_BAUDRATE                115200
-
 #define CONFIG_PREBOOT "echo;" \
        "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
        "echo"
@@ -573,8 +520,6 @@
 
 #define CONFIG_BOOTCOMMAND     "run flash_self"
 
-#define CONFIG_OF_LIBFDT       1
-#define CONFIG_OF_BOARD_SETUP  1
 #define CONFIG_OF_SUPPORT_OLD_DEVICE_TREES     1
 
 #define OF_CPU                 "PowerPC,5121@0"
@@ -587,8 +532,6 @@
  *-----------------------------------------------------------------------
  */
 
-#undef  CONFIG_IDE_8xx_PCCARD          /* Use IDE with PC Card Adapter */
-#undef CONFIG_IDE_8xx_DIRECT           /* Direct IDE    not supported  */
 #undef CONFIG_IDE_LED                  /* LED   for IDE not supported  */
 
 #define CONFIG_IDE_RESET               /* reset for IDE supported      */