config OF_CONTROL
bool "Run-time configuration via Device Tree"
select DTC
+ select OF_LIBFDT if !OF_PLATDATA
help
This feature provides for run-time configuration of U-Boot
via a flattened device tree.
config SPL_OF_CONTROL
bool "Enable run-time configuration via Device Tree in SPL"
depends on SPL && OF_CONTROL
+ select SPL_OF_LIBFDT if !SPL_OF_PLATDATA
help
Some boards use device tree in U-Boot but only have 4KB of SRAM
- which is not enough to support device tree. Enable this option to
+ which is not enough to support device tree. Disable this option to
allow such boards to be supported by U-Boot SPL.
config TPL_OF_CONTROL
bool "Enable run-time configuration via Device Tree in TPL"
depends on TPL && OF_CONTROL
+ select TPL_OF_LIBFDT if !TPL_OF_PLATDATA
help
Some boards use device tree in U-Boot but only have 4KB of SRAM
which is not enough to support device tree. Enable this option to
device tree files (without the directory or .dtb suffix)
separated by <space>.
+config OF_OVERLAY_LIST
+ string "List of device tree overlays to include for DT control"
+ depends on SPL_LOAD_FIT_APPLY_OVERLAY
+ help
+ This option specifies a list of device tree overlays to use for DT
+ control. This option can then be used by a FIT generator to include
+ the overlays in the FIT image.
+
+choice
+ prompt "OF LIST compression"
+ depends on MULTI_DTB_FIT
+ default MULTI_DTB_FIT_NO_COMPRESSION
+
+config MULTI_DTB_FIT_LZO
+ bool "LZO"
+ depends on SYS_MALLOC_F
+ select LZO
+ help
+ Compress the FIT image containing the DTBs available for the SPL
+ using LZO compression. (requires lzop on host).
+
+config MULTI_DTB_FIT_GZIP
+ bool "GZIP"
+ depends on SYS_MALLOC_F
+ select GZIP
+ help
+ Compress the FIT image containing the DTBs available for the SPL
+ using GZIP compression. (requires gzip on host)
+
+config MULTI_DTB_FIT_NO_COMPRESSION
+ bool "No compression"
+ help
+ Do not compress the FIT image containing the DTBs available for the SPL.
+ Use this options only if LZO is not available and the DTBs are very small.
+endchoice
+
+choice
+ prompt "Location of uncompressed DTBs"
+ depends on (MULTI_DTB_FIT_GZIP || MULTI_DTB_FIT_LZO)
+ default MULTI_DTB_FIT_DYN_ALLOC if SYS_MALLOC_F
+
+config MULTI_DTB_FIT_DYN_ALLOC
+ bool "Dynamically allocate the memory"
+ depends on SYS_MALLOC_F
+
+config MULTI_DTB_FIT_USER_DEFINED_AREA
+ bool "User-defined location"
+endchoice
+
+config MULTI_DTB_FIT_UNCOMPRESS_SZ
+ hex "Size of memory reserved to uncompress the DTBs"
+ depends on (MULTI_DTB_FIT_GZIP || MULTI_DTB_FIT_LZO)
+ default 0x8000
+ help
+ This is the size of this area where the DTBs are uncompressed.
+ If this area is dynamically allocated, make sure that
+ SYS_MALLOC_F_LEN is big enough to contain it.
+
+config MULTI_DTB_FIT_USER_DEF_ADDR
+ hex "Address of memory where dtbs are uncompressed"
+ depends on MULTI_DTB_FIT_USER_DEFINED_AREA
+ help
+ the FIT image containing the DTBs is uncompressed in an area defined
+ at compilation time. This is the address of this area. It must be
+ aligned on 2-byte boundary.
config DTB_RESELECT
bool "Support swapping dtbs at a later point in boot"
config OF_SPL_REMOVE_PROPS
string "List of device tree properties to drop for SPL"
depends on SPL_OF_CONTROL
- default "interrupt-parent" if SPL_PINCTRL && SPL_CLK
- default "clocks clock-names interrupt-parent" if SPL_PINCTRL
- default "pinctrl-0 pinctrl-names interrupt-parent" if SPL_CLK
- default "pinctrl-0 pinctrl-names clocks clock-names interrupt-parent"
+ default "interrupt-parent interrupts" if SPL_PINCTRL && SPL_CLK
+ default "clocks clock-names interrupt-parent interrupts" if SPL_PINCTRL
+ default "pinctrl-0 pinctrl-names interrupt-parent interrupts" if SPL_CLK
+ default "pinctrl-0 pinctrl-names clocks clock-names interrupt-parent interrupts"
help
Since SPL normally runs in a reduced memory space, the device tree
is cut down to only what is needed to load and start U-Boot. Only
can be discarded. This option defines the list of properties to
discard.
+config OF_DTB_PROPS_REMOVE
+ bool "Enable removal of device tree properties"
+ depends on OF_CONTROL
+ help
+ Some boards have restricted amount of storage for U-Boot image.
+ If the generated binary doesn't fit into available image storage,
+ the built-in device tree could probably be cut down by removing
+ some not required device tree properties to reduce the image size.
+ Enable this option and define the properties to be removed in the
+ CONFIG_OF_REMOVE_PROPS list. Do not enable this option if you must
+ pass the built-in DTB directly to the kernel!
+
+config OF_REMOVE_PROPS
+ string "List of device tree properties to drop"
+ depends on OF_DTB_PROPS_REMOVE
+ default "interrupt-parent interrupts" if PINCTRL
+ help
+ Some properties are not used by U-Boot and can be discarded.
+ This option defines the list of properties to discard.
+
config SPL_OF_PLATDATA
bool "Generate platform data for use in SPL"
depends on SPL_OF_CONTROL
projects / oweals / u-boot.git / blobdiff